Samsung DVD-AR650 User Manual
Instruction Manual
DVD-AR650
www.samsung.com
AK68-01378A
Getting Started
Warning
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE THE COVER(OR BACK).
Getting Started
NO USER-SERVICEABLE PARTS ARE INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol indicates that dangerous voltage
consisting a risk of electric shock is present
within this unit.
This symbol indicates that there are important
operating and maintenance instructions in the
literature accompanying this unit.
Do not install this equipment in a confi ned space such as
a bookcase or similar unit.
WARNING :
shock hazard, do not expose this appliance to rain or moisture.
CAUTION : DVD RECORDERS USE AN INVISIBLE LASER
BEAM WHICH CAN CAUSE HAZARDOUS RADIATION
EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE
RECORDER CORRECTLY AS INSTRUCTED.
CAUTION
THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR
YOURSELF. REFER SERVICING TO QUALIFIED
PERSONNEL.
CAUTIONS
Caution: To prevent electric shock, match wide blade of plug
to wide slot, fully insert.
Attention: Pour éviter les chocs électriques, introduíre la lame
la plus large de la fi che dans la borne correspondante de la
prise et pousser jusqu au fond.
This product satisfi es FCC regulations when shielded
cables and connectors are used to connect the unit to other
equipment. To prevent electromagnetic interference with
electric appliances, such as radios and televisions, use
shielded cables and connectors for connections.
FCC NOTE (for U.S.A):
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
To prevent damage which may result in fi re or electric
English - 2
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
•
Caution: FCC regulations state that any unauthorized changes
or modifi cations to this equipment may void the user's
authority to operate it.
This unit can be used only where the power supply
■
is AC 120V, 60Hz. It cannot be used elsewhere.
■
This DVD Recorder is designed and manufactured to
respond to the Region Management Information.
If the Region number of a DVD disc does not correspond
to the Region number of this DVD Recorder, the DVD
Recorder cannot play the disc.
■
This device is protected by U.S. Patent Nos.4,631,60
3;4,577,216;4,819,098;4,907,093; and 6,516,132.This
product incorporates copyright protection technology
that is protected by U.S. patents and other intellectual
property rights.Use of this copyright protection
technology must be authorized by Macrovision,and is
intended for home and other limited viewing uses only
unless otherwise authorized by Macrovision.Reverse
engineering or disassembly is prohibited.
■
This product is covered by one or more of the
following U.S. patents:
5,060,220 5,457,669 5,561,649 5,705,762 5,987,417
6,043,912 6,222,983 6,272,096 6,377,524 6,377,531
6,385,587 6,389,570 6,408,408 6,466,532 6,473,736
6,477,501 6,480,829 6,556,520 6,556,521 6,556,522
6,578,163 6,594,208 6,631,110 6,658,588 6,674,697
6,674,957 6,687,455 6,697,307 6,707,985 6,721,243
6,721,493 6,728,474 6,741,535 6,744,713 6,744,972
6,765,853 6,765,853 6,771,890 6,771,891 6,775,465
6,778,755 6,788,629 6,788,630 6,795,637 6,810,201
6,862,256 6,868,054 6,894,963 6,937,552
Precaution
Important Safety Instructions
▌
Read these operating instructions carefully before using
the unit. Follow all the safety instructions listed below.
Keep these operating instructions handy for future
reference.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with a dry cloth.
7) Do not block any ventilation openings, Install in
accordance with the manufacturer's instructions.
8) Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifi ers) that produce heat.
9) Do not defeat the safety purpose of the polarized or
grounding- type plug. A polarized plug has two blades
with one wider than the other. A groundingtype plug
has two blades and a third grounding prong. The wide
blade or the third prong is provided for your safety. If
the provided plug does not fi t into your outlet, consult
an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11) Only use attachments/accessories specifi ed by the
manufacturer.
12) Use only with the cart, stand, tripod,
bracket, or table specifi ed by the
manufacturer, or sold with the
apparatus. When a cart is used,
use caution when moving the cart/
apparatus combination to avoid injury
from tip-over.
13) Unplug this apparatus during lightning storms or when
unused for long periods of time.
14) Refer all servicing to qualifi ed service personnel.
Service is required when the apparatus has been
damaged in any way, such as the power-supply cord
or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus. Service is also required
if the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
• Exterior interference such as lightning and static
electricity can affect normal operation of this recorder.
If this occurs, turn the recorder off and on again with the
POWER button, or disconnect and then reconnect the
AC power cord to the AC power outlet.
The recorder will operate normally.
• Be sure to remove the disc and turn off the recorder after
use.
• Disconnect the AC power cord from the AC outlet when
you don’t intend to use the recorder for long periods of
time.
• Clean the disc by wiping in a straight line from the inside
to the outside of the disc.
• Apparatus shall not be exposed to dripping or splashing
and no objects fi lled with liquids, such as vases, shall be
placed on the apparatus.
• The Mains plug is used as a disconnect device and shall
stay readily operable at any time.
Maintenance of Cabinet
▌
For safety reasons, be sure to disconnect the AC power
cord from the AC outlet.
• Do not use benzene, thinner, or other solvents for
cleaning.
• Wipe the cabinet with a soft cloth.
▌
Disc Handling
• Use discs with regular
shapes. If an irregular disc (a
disc with a special shape) is
used, this DVD Recorder may
be damaged.
Holding discs
• Avoid touching the surface of a disc
where recording is performed.
DVD-RAM, DVD-RW and DVD-R
• Clean with an optional DVD-RAM/PD disc
cleaner . Do not use cleaners or cloths for
CDs to clean DVD-RAM/
DVD-RW/DVD-R discs.
DVD-Video, Audio CD
• Wipe off dirt or contamination on the disc with a soft
cloth.
Getting Started
Handling Cautions
▌
• Before connecting other components to this recorder, be
sure to turn them all off.
• Do not move the recorder while a disc is being played, or
the disc may be scratched or broken, and the recorder’s
internal parts may be damaged.
• Do not put a fl ower vase fi lled with water or any small
metal objects on the recorder.
• Be careful not to put your hand into the disc tray.
• Do not place anything other than the disc in the disc tray.
English - 3
Cautions on handling discs
• Do not write on the printed side with a ball-point pen or
pencil.
• Do not use record cleaning sprays or antistatic. Also, do
not use volatile chemicals, such as benzene or thinner.
• Do not apply labels or stickers to discs. (Do not use discs
fi xed with exposed tape adhesive or leftover peeled-off
stickers.)
• Do not use scratch-proof protectors or covers.
• Do not use discs printed with label printers available on
the market.
• Do not load warped or cracked discs.
Disc Storage
▌
Be careful not to damage the disc because the data on
these discs are highly vulnerable to the environment.
• Do not keep under direct sunlight.
• Keep in a cool ventilated area.
• Store vertically.
• Keep in a clean protection jacket.
Getting Started
• If you move your DVD Recorder suddenly from a cold
place to a warm place, condensation may generate
on the operating parts including the lens and cause
abnormal disc playback. When this occurs, do not
connect the plug to the power outlet. Wait for two hours,
then insert the disc and try to playback again. It will work
properly when condensation has evaporated.
▌
Disc Specifi cations
DVD-Video
• A digital versatile disc (DVD) can contain up to
135-minutes of images, 8-language audio and 32
subtitle languages. It is equipped with MPEG-2 picture
compression and Dolby 3D surround sound, allowing
you to enjoy vivid and clear theater quality images in the
comfort of your own home.
• When switching from the fi rst layer to the second layer
of a double-layered DVD Video disc, there may be
momentary distortion in the image and sound. This is not
a malfunction of the unit.
• Once a DVD-R/DVD-RW(V) recorded is fi nalized, it is
playable in a standard DVD player.
Audio CD
• An audio disc on which 44.1kHz PCM Audio is recorded
• Plays CD-DA format audio CD-R and CD-RW discs.
The unit may not be able to play some CD-R or CD-RW
discs due to the condition of the recording.
CD-R/-RW
MP3 CD-R/-RW
• Only CD-R discs with MP3 fi les recorded with ISO9660
or JOLIET format can be played back
• Only MP3 fi les with the ".mp3", ".MP3" extension can be
used.
• For MP3 fi les recorded with a VBR(Variable Bit Rates),
from 32 Kbps to 320 Kbps, the sound may cut in out.
• Playable bitrate range is from 56Kbps to 320Kbps.
• The unit can handle a maximum of 1000 fi les and
folders.
JPEG CD-R/-RW
• Only JPEG fi les with the ".jpg", ".JPG" extension can be
used.
• The unit can handle a maximum of 1000 fi les and
folders.
• Maximum size of progressive JPEG is 3M pixels.
• MOTION JPEG is not supported.
Using MPEG4 disc
• Disc : CD-R/-RW, DVD-RAM, DVD-R/ DVD-RW,
• MPEG4 File with following extensions can be played. :
.avi, .divx, .AVI, .DIVX
• MPEG4 Codec format : DivX 3.11 DivX 4.x DivX 5.x
• Available Audio Format : “MP3”, “MPEG”, “PCM”,“AC3”,
“DTS”
• Supported subtitle fi le formats: .smi, .srt, .sub, .psb,.txt
Using CD-R/-RW
• Use a 700MB(80 minutes) CD-R/-RW disc. If possible,
do not use a 800MB(90 minutes) or above disc, as the
disc may not play back.
• If the CD-R/-RW disc was not recorded as a closed
session, you may experience a delay in the early
playback time, and all recorded fi les may not play.
• Some CD-R/-RW discs may not be playable with this
unit, depending on the device which was used to burn
them.
• When recording from CDs for your personal use to CDR/-RW discs on your computer, playability may vary
depending on the contents and discs.
DVD-R Disc Playback and Recording
• Once a DVD-R recorded is fi nalized, it is playable in a
standard DVD player.
You can record onto the available space on the disc and
perform editing functions such as giving titles to discs
and programs and erasing programs before fi nalizing.
• When programming is erased from a DVD-R, that space
does not become available. Once an area on a DVD-R
is recorded on, that area is no longer available for
recording, whether the recording is erased or not.
• It takes about 30 seconds for the unit to complete
recording management information after recording
fi nishes.
• This product optimizes the DVD-R for each recording.
Optimization occurs when you start recording after
inserting the disc or turning on the unit. Recording onto
the disc may become impossible if optimization is carried
out too many times.
• Playback may be impossible in some cases due to the
condition of recording.
• This unit can play back DVD-R discs recorded and
fi nalized with a Samsung DVD video recorder. It may
not be able to play some DVD-R discs depending on the
disc and the condition of the recording.
DVD-RW Disc Playback and Recording
• Recording and playback can be performed on DVD-RW
discs in both the Video and VR Modes.
• Once a DVD-RW recorded in VR or Video mode is
fi nalized, you cannot perform additional recording.
• Once a DVD-RW is recorded in Video Mode and
fi nalized, it becomes a DVD-Video.
• In both modes, playback can be performed before and
after fi nalization, but additional recording, deleting and
editing can not be performed after fi nalization.
• If you want to record the disc in VR Mode and then
record in V Mode, be sure to fi rst reformat the disc.
Please be aware that formatting may erase all of the
disc's content.
English - 4
• When inserting an unused disc, a message will appear
asking whether to initialize the disc or not. If you select
"YES", the disc will be formatted in VR mode.
• DVD-RW (VR mode)
- This is a format that is used for recording data on a
DVD-RW disc. You can record multiple titles, edit, delete,
partial delete, create a playlist, etc.
- A disc that is recorded in this mode will not play in
standard DVD players.
• DVD-RW (Video mode)
- This is a format that is used for recording data on a
DVD-RW or DVD-R disc. The disc can be played by an
existing DVD player once it has been fi nalized.
- If a disc that has been recorded in Video Mode by a
different maker’s recorder but has not been fi nalized, it
cannot be played or recorded by this recorder.
DVD-RAM Disc Playback and Recording
• For cartridge type DVD-RAM discs, remove the cartridge
and use only the disc
• Ensure that the recording mode is set to VR.
Otherwise, this product will not be able to play the
recording.
• You cannot play a DVD-RAM in most DVD players due
to compatibility issues.
• Only DVD-RAM standard Version 2.0 discs can be
played in this unit.
•
DVD-RAM discs recorded on this unit may not work with
other DVD Players. To determine compatibility with these
DVD-RAM discs, refer to the user’s manual for the player.
COPY PROTECTION
• Many DVD discs are encoded with copy protection.
Because of this, you should only connect your DVD
Recorder directly to your TV, not to a VCR.
Connecting your DVD recorder to a VCR results in a
distorted picture from copy-protected DVD discs.
• This product incorporates copyright protection
technology that is protected by methods claims of
certain U.S. patents and other intellectual property
rights owned by Macrovision Corporation and other
rights owners. Use of this copyright protection
technology must be authorized by Macrovision
Corporation, and is intended for home and other
limited viewing uses only unless otherwise authorized
by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.
Protection
This DVD Recorder can allow you to protect the contents
of your discs, as described below.
• Program-protection: See page 69 “Locking a Title”
• Disc-protection: See page 76 “Disc Protection”
✻
DVD-RAM/DVD-RW/DVD-R discs that are incompatible
with the DVD-VIDEO format cannot be played with this
product.
✻
For more information on DVD recording compatibility,
consult your DVD-RAM/DVD-RW/DVD-R manufacturer.
✻
Use of poor quality DVD-RAM/DVD-RW/DVD-R discs
may cause the following unexpected problems including,
recording failure, loss of recorded or edited materials or
damage to the recorder.
Do not use the following discs!
• LD, CD-G, CD-I, CD-ROM and DVD-ROM discs should
not be used in this product.
[Note]
Disc types that can be played :
CD/CD-R/CD-RW/MP3/JPEG/DVD-Video/DVD-RAM/
DVD-RW/ DVD-R.
DVD+R/+RW cannot record, but fi nalized +R/+RWs
can be played.
A DVD-R/DVD-RW disc which has been recorded in Video
Mode on another component can play only when fi nalized.
• Some commercial discs and DVD discs purchased
outside your region may not be playable with this
product. When these discs are played, either “No Disc."
or "The disc cannot be played. Please check the regional
code of the disc." will be displayed.
• If your DVD-RAM/DVD-RW/DVD-R disc is an illegal
copy or is not in DVD video format, it may also not be
playable.
Disc Compatibility
• Not all brands of discs will be compatible with this unit.
• The latest fi rmware upgrade to improve recording &
playback quality can be downloaded from our web site.
(Download Center at www.samsung.com)
• If disc compatibility problems continue, or there is an
issue upgrading your recorder, contact the Call Center at
1-800-SAMSUNG.
Getting Started
English - 5
Contents
Getting Started
Warning ...................................................................2
■
Getting Started
Precaution ............................................................... 3
■
Important Safety Instructions ..................................3
Handling Cautions ................................................... 3
Maintenance of Cabinet .......................................... 3
Disc Handling ..........................................................3
Disc Storage ............................................................ 4
Disc Specifi cations .................................................. 4
General Features ....................................................8
■
Before Reading the Instruction Manual ...................9
■
How to use the DVD Recorder ................................9
■
Unpacking ............................................................... 10
■
Accessories ............................................................. 10
Preparing the Remote Control ................................10
Tour of the Remote Control .....................................12
Description .............................................................. 13
■
Front Panel .............................................................. 13
Front Panel Display ................................................. 13
Rear Panel .............................................................. 14
Connecting & Setting Up
Step 1: Connecting the Antenna Cable ...................15
■
Antenna + DVD Recorder + TV ............................... 15
Antenna + Cable box or satellite receiver (set top box) +
DVD Recorder + TV : Cable box/Satellite receiver with
a video/audio output
Antenna + Cable box or satellite receiver (set top box) +
DVD Recorder + TV : Cable box/Satellite receiver with
an antenna output only
Step 2 : Connecting HDMI/DVI to a TV ...................18
■
Connecting to a TV with HDMI Jack .......................18
Connecting to a TV with DVI Jack ........................... 19
Step 3 : Connecting the Video Cable ......................20
■
Connecting to Component Video Input Jacks
(Y,P
Connecting to an S-Video Input Jack ...................... 21
Connecting to a Video Input Jack ...........................22
Step 4 : Connecting the Audio Cable ......................23
■
Connecting to your TV ............................................23
Connecting to a Stereo Amplifi er with Analog Input
Jacks ....................................................................... 24
Connecting to an AV Amplifi er with a Digital Input
Jack ......................................................................... 25
) .................................................................. 20
B,PR
.................................................. 16
................................................ 17
Step 5 : Connecting External Devices ..................... 26
■
Connecting a VCR, Cable box/Satellite receiver
(set top box) or DVD Player to the AV 1 IN or
S-VIDEO IN Jacks ................................................... 26
Connecting a Camcorder ........................................ 27
System Setup
On-Screen Menu Navigation ...................................28
■
Plugging In & Auto Setup ........................................ 28
■
Auto Clock Set ......................................................... 29
■
Time Zone ...............................................................29
Daylight Saving ....................................................... 29
Manual Clock Set .................................................... 30
■
Auto Channel Memory ............................................. 30
■
Manual Channel Set ................................................ 31
■
Setting Up the System Options ............................... 32
■
Set Top Box Control ................................................32
CM Skip Time Setting ..............................................33
EP Mode Time Setting ............................................ 34
Automatic Chapter Creation .................................... 34
Quick Recording Setting .........................................35
Anynet+(HDMI-CEC)...............................................35
Language Setting .................................................... 36
■
Digital Caption .........................................................37
■
Setting Up the Audio Options ..................................38
■
Video(Display) Setting ............................................. 39
■
TV Aspect ................................................................39
Input Level ............................................................... 39
Black Level .............................................................. 40
3D Noise Reduction ................................................ 40
HDMI/DVI Resolution ..............................................40
DivX(R) Registration ...............................................40
Parental Control ......................................................41
■
Setting the Rating Level ..........................................41
Setting the Digital Rating ......................................... 41
Changing the Password ..........................................42
EPG-Electronic Program Guide ..............................42
■
Viewing Full Guide and Mini Guide .........................43
EPG Timer Recording ............................................. 43
English - 6
Getting Started
Recording
Recordable discs ..................................................... 44
■
Compatibility between Samsung and Other
manufacturer's Recorders ....................................... 44
Recording Formats .................................................. 45
■
DVD-RAM/-RW(VR mode) ...................................... 45
DVD-RW(Video mode)/-R ....................................... 45
Recording Mode ...................................................... 46
■
Unrecordable Video ................................................. 46
■
About the INFO Button ............................................ 47
Recording immediately ............................................ 48
■
Recording the current TV program you are watching
Recording from External Equipment ....................... 48
Copying from a Camcorder ..................................... 49
■
Making a One Touch Recording (OTR) ................... 50
■
Setting a Timer Recording ....................................... 51
■
Flexible Recording (for Timer Recording only) ........ 52
■
Editing the Scheduled Record List .......................... 52
■
Deleting the Scheduled Record List ........................ 53
■
Recording the Scheduled Record List ..................... 53
■
EZ REC MODE .......................................................54
■
.. 48
Editing
Basic Editing (Title List) ........................................... 68
■
Renaming (Labeling) a Title .................................... 68
Locking (Protecting) a Title ......................................69
Deleting a Title ........................................................ 69
Deleting a Section of a Title .................................... 70
Advanced Editing (Playlist) ...................................... 71
■
Creating a Playlist ................................................... 71
Playing Entries in the Playlist .................................. 71
Renaming a Playlist Entry ....................................... 72
Editing a Scene for the Playlist ...............................72
Copying a Playlist Entry to the Playlist .................... 75
Deleting a Playlist Entry from the Playlist ................ 75
■
Disc Manager .......................................................... 75
Editing the Disc Name ............................................. 75
Disc Protection ........................................................ 76
Formatting a Disc .................................................... 76
Finalizing a Disc ...................................................... 77
Unfi nalizing a Disc (V/VR mode) ............................. 77
Delete All Title Lists .................................................78
Additional Information
Playback
Region code (DVD-Video only) ............................... 55
■
Logos of Discs that can be played ..........................55
■
Disc types that can be played .................................55
■
Discs That Cannot be Played .................................. 56
Playing a Disc .......................................................... 56
■
Using the Disc Menu & Title Menu .......................... 57
Using the Playback Related Buttons ....................... 57
Slow Motion Play ..................................................... 58
Step Motion Play ..................................................... 58
Using the ANYKEY Button ...................................... 59
Playing an Audio CD/MP3 ....................................... 63
■
Playing an Audio CD(CD-DA) ................................. 63
Playing an MP3 Disc ............................................... 64
Playing Repeatedly ................................................. 64
Playing a Picture CD ............................................... 65
■
Playing an MPEG4 Disc .......................................... 66
■
Playing the Title List ................................................ 67
■
■
Troubleshooting ....................................................... 79
■
Cable Box/Satellite Receiver Brand Code Table ..... 81
Cable box brand ...................................................... 81
Satellite receiver brand ...........................................83
Error Message Solutions ......................................... 84
■
Specifi cations ..........................................................86
■
Warranty .................................................................. 87
■
English - 7
General Features
The DVD-AR650 allows you to record and play high
quality digital video on DVD-RAM/DVD-RW/DVD-R discs.
High quality digital audio and video recording and
Getting Started
playback
You can record up to approximately 16-hours of video on
a double side 9.4 GB DVD-RAM disc,up to 15-hours on a
dual-layer 8.5GB DVD-R disc, and up to 8-hours on a 4.7
GB DVD-RAM/DVD-RW/DVD-R disc, depending on the
recording mode.
A variety of functions with an easy-to-use user interface
The integrated menu system and the messaging function
allows you to perform desired operations both easily and
conveniently. With a DVD-RAM or DVD-RW (VR mode)
disc, you can edit recorded images, create a playlist,
and edit videos in a specifi c sequence according to your
requirements.
MPEG4 playback
This DVD Recorder can play MPEG4 formats within an avi
fi le.
Selectable Record Mode
You can set your recorder to one of fi ve different recording
speeds, each varying in recording quality and length. EP
mode yields the most recording time, LP & SP modes
provide less recording time with higher quality recording,
and XP mode gives you the highest quality recording.
There's also the FR (Flexible Recording) mode that lets
you record with the best picture quality possible for the
recording time and remaining space on the disc during
timer recording.
Automated Quality Adjustment for Timer Recording
If FR mode is selected, the video quality is adjusted
automatically so that all video for the scheduled time can
be recorded onto the free disc space. (See pages 51~52)
Create a DVD video title using a DVD-RW/DVD-R disc
With the DVD-AR650, you can create your own DVD
video title on 4.7 GB DVD-RW/DVD-R or 8.5GB DVD-R
discs.
Copying data from a digital camcorder using a DV
input jack
Record digital camcorder video onto DVD-RAM, DVD-RW
or DVD-R discs using the DV input jack (IEEE 1394-4pin).
(See page 49)
DivX Certifi cation
DivX, DivX Certifi ed, and associated logos
are trademarks of DivXNetworks, Inc and
are used under license.
HDMI (High Defi nition Multimedia Interface)
HDMI reduces picture noise by allowing a pure digital
video/audio signal path from the DVD Recorder to your
TV.
EZ REC MODE
This function allows you to Initialize and Finalize a disc
automatically. (See page 54)
High quality progressive scan
Progressive scanning provides high resolution and fl icker
free video.
The 10-bit 54-MHz DAC and 2D Y/C Separating Circuitry
provides the highest video playback and recording quality.
(See page 20)
English - 8
Before Reading the Instruction Manual
Make sure to check the following before reading the
user’s manual.
Icons that will be used in manual
Icon Term Defi nition
This involves a function available
DVD
RAM
-RW
JPEG
MP3
MPEG4
Caution
NOTE
One-
Touch
button
ANYKEY
button
About the use of this Instruction Manual
1) Be sure to familiarize yourself with the Safety
Instructions before using this product. (See pages 2 ~ 5)
2) If a problem occurs, check the Troubleshooting section.
(See pages 79~80)
Copyright
©2007 Samsung Electronics Co.
All rights reserved; No part or whole of this user’s manual
may be reproduced or copied without the prior written
permission of Samsung Electronics Co.
with DVD or DVD-R/DVD-RW (V)
discs that have been recorded and
fi nalized.
This involves a function available
with DVD-RAM discs.
This involves a function available
with DVD-RW discs.
This involves a function available
-R
with DVD-R discs.
This involves a function available
CD
with a data CD (CD-R or CD-RW).
This involves a function available
with JPEG fi les on CD-R/-RW or
DVD-RAM/DVD-RW/DVD-R discs.
This involves a function available
MP3 fi les on CD-R/-RW or DVD-
RAM/DVD-RW/DVD-R discs.
This involves a function available
with MPEG4s on CD-R/-RW or
DVD-RAM/DVD-RW/DVD-R discs.
This involves a case where a
function does not operate or
settings may be cancelled.
This involves tips or instructions on
the page that help each function
operate.
A function that can be operated by
using only one button.
A function that can be operated by
using the ANYKEY button.
How to use the DVD Recorder
Step 1 : Select the disc type
▌
This unit can record on the following types of discs.
If you want to repeatedly record on the same disc or you
want to edit the disc after recording, select a rewritable
DVD-RW or DVD-RAM type disc.
If you want to save the recording without making any
changes, choose a non-rewritable DVD-R.
▌
Step 2 : Format the disc to start recording
The recorder automatically starts formatting when an
unused disc is inserted. This is required for the preparation
of disc recording.
Using a DVD-RAM
This type of disc can be formatted with the DVD-Video
Recording format (VR mode). You can edit recorded video
and create a playlist and edit video in a specifi c sequence
according to your requirements.
Using a DVD-RW
• When an unused DVD-RW disc is fi rst inserted, the
message “Uninitialized Disc. Do you want to initialize this
disc?” will be displayed.
If you select Yes, initializing will begin. A DVD-RW disc
can be formatted in either DVD-Video format (Video
mode) or DVD-Video Recording format (VR mode)
Using a DVD-R
When using a DVD-R disc, only V mode recording is
possible and no initialization is needed to play it on this
recorder. However, fi nalization is necessary to play this
disc on other DVD players.
You can only use either the VR or Video mode on
■
a DVD-RW, but not both at the same time.
You can format a DVD-RW to V or VR mode using
■
disc manager.
It should be noted that the disc's data will be lost
when changing formats.
Step 3 : Recording
▌
There are two different recording methods. Direct Recording
(recording a program you are currently watching) and
Timer Recording. Timer recording is determined as a Date :
MM/DD, MON-FRI, Every SAT, etc.. There are 5 recording
modes : XP(high quality mode), SP(standard quality mode),
LP(long recording mode), EP(extended mode) and FR
mode. When using FR mode to record, the picture quality is
determined by the remaining time on the disc.
You can make a Timer Recording by using the
■
EPG (Electronic Program Guide). (See page 43)
Getting Started
English - 9
Step 4 : Playing
▌
To start playback select the title you want to play from the
Title list.
A DVD consists of sections called titles, and sub sections
called chapters.
During recording, a title is created between two points
where you start and stop recording. Chapters will be
Getting Started
created automatically when you fi nalize recording on
DVD-R/DVD-RW discs in Video mode.
▌
Step 5 : Editing a recorded disc
Editing on discs is easier than editing on conventional
video tapes. The recorder supports many different edit
functions, possible only with DVDs.
With a simple and easy edit menu, you can operate various
edit functions, such as delete, copy, rename, lock, etc., on
a recorded title.
With this recorder, you can create playlists using a DVDRAM/DVD-RW in VR mode. Once a playlist is created you
can create/edit a new playlist on the same disc without
changing the original recording.
▌
Step 6
:
Finalizing & Playing on other
DVD components
To play your DVD on other DVD components, fi nalizing
may be necessary. First, fi nish all editing and recording
operations, then fi nalize the disc.
When using a DVD-RW disc in VR Mode
Although fi nalizing is generally unnecessary when playing
the disc on a VR Mode compatible component, a fi nalized
disc should be used for playback.
When using a DVD-RW disc in Video Mode
The disc should be fi nalized fi rst to enable playback
on anything other than this recorder. No more editing
or recording can be made on the disc once it has been
fi nalized.
When using a DVD-R disc
You should fi nalize the disc to play it on a component
other than this recorder. No more editing or recording can
be made on the disc once it has been fi nalized.
Unpacking
Accessories
▌
Check for the supplied accessories below.
Video/Audio Cable
(AC39-00073A)
Remote Control
(AK59-00062J)
Instruction Manual
(AK68-01378A)
Preparing the Remote Control
▌
Install Batteries in the Remote Control
• Open the battery cover on the back of the remote.
• Insert two AAA batteries. Make sure that the polarities
(+ and -) are aligned correctly.
• Replace the battery cover.
If the remote control does not operate properly:
• Check the polarity +/- of the batteries.
• Check if the batteries are drained.
• Check if the remote sensor is blocked by obstacles.
• Check if there is any fl uorescent lighting nearby.
IR Blaster cable
(AK39-00055A)
Batteries for Remote
Control (AAA Size)
(AC43-12002H)
Quick Guide
(AK68-01379A)
You can fi nalize automatically using the EZ REC
■
MODE. (See page 54)
Dispose of batteries according to local environmental
regulations. Do not put them in the household trash.
English - 10
To determine whether your television is compatible, follow the instructions below.
1. Switch your television on.
2. Point the remote control towards the television.
3. Press and hold the TV POWER button and enter the two-figure code simultaneously corresponding to the brand of
your television by pressing the appropriate number buttons.
Getting Started
Brand BUTTON
AIWA 82
ANAM 10, 11, 12, 13, 14, 15, 16, 17, 18
BANG &
OLUFSEN
BLAUPUNKT 71
BRANDT 73
BRIONVEGA 57
CGE 52
CONTINENTAL EDISON
DAEWOO
EMERSON 64
FERGUSON 73
FINLUX 06, 49, 57
FORMENTI 57
FUJITSU 84
GRADIENTE 70
GRUNDIG 49, 52, 71
HITACHI 60, 72, 73, 75
IMPERIAL 52
JVC 61, 79
LG 06, 19, 20, 21, 22, 78
LOEWE 06, 69
LOEWE OPTA 06, 57
MAGNAVOX 40
METZ 57
MITSUBISHI 06, 48, 62, 65
MIVAR 52, 77
NEC 83
NEWSAN 68
NOBLEX 66
NOKIA 74
NORDMENDE 72, 73, 75
PANASONIC 53, 54, 74, 75
PHILIPS 06, 55, 56, 57
PHONOLA 06, 56, 57
PIONEER 58, 59, 73, 74
RADIOLA 06, 56
RADIOMARELLI
RCA 45, 46
REX 74
57
75
19, 20, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34
57
BRAND BUTTON
SABA 57, 72, 73, 74, 75
SALORA 74
SAMSUNG 01,02,03,04,05,06,07,08,09
SANYO 41, 42, 43, 44, 48
SCHNEIDER 06
SELECO 74
SHARP 36, 37, 38, 39, 48
SIEMENS 71
SINGER 57
SINUDYNE 57
SONY 35, 48
TELEAVA 73
TELEFUNKEN 67, 73, 75, 76
THOMSON 72, 73, 75
THOMSON ASIA
TOSHIBA 47, 48, 49, 50, 51, 52
WEGA 57
YOKO 06
ZENITH 63
Result: If your television is compatible with the remote
control, it will switch off.
It is now programmed to operate with the remote
control.
If several codes are indicated for your television
■
brand, try each one in turn until you fi nd one
that works. If you replace the remote control’s
batteries, you must set the brand code again.
If you select TV mode, you can then control your
television using the following buttons.
Button Function
TV POWER
INPUT SEL. Used to select an external source.
TV VOL +/-
CH ( / ) Used to select the desired channel.
TV MUTE Used to toggle the sound on and off.
0~9 Used to input number directly.
Various functions may be controllable on your
■
television. If you encounter problems, operate the
television directly.
80, 81
Used to switch the television on and off.
Used to adjust the volume of the television.
English - 11
Tour of the Remote Control
▌
You can control certain functions of another manufacturer's TV with this remote control.
• Buttons that can be controlled on your TV : TV POWER, INPUT SEL., TV VOL (+/-), CH (
/ ), TV MUTE, 0~9.
Getting Started
10
11
12
13
14
15
16
17
18
19
1
2
3
4
5
6
7
8
9
1. TV Button
Press this to operate your TV.
2. DVD Button
Press this to operate your DVD Recorder.
3. POWER Button
Press to power the DVD Recorder on and off.
4. NUMBER Buttons
5. DASH (_) Button
Press to select additional channels (digital and analog)
being broadcast by the same station. For example, to
select channel “54-3”, press “54”, then press “
6. REVERSE/FORWARD SKIP Buttons
Press to skip a disc backwards or forwards.
7. REVERSE/FORWARD STEP Buttons
Press to play frame by frame.
8. REVERSE/FORWARD SEARCH Buttons
Press to search a disc backwards or forwards.
9. STOP Button
Press to stop a disc or to stop the recording.
10. TV VOL Buttons
Volume adjustment.
11. MENU Button
Brings up the DVD recorder’s setup menu.
12. ENTER/DIRECTION Buttons
(UP/DOWN and LEFT/RIGHT Buttons)
This button functions as a toggle switch.
20
21
22
23
24
6
8
25
26
27
28
29
30
31
32
33
34
35
-
” and “3”.
13. TITLE LIST/DISC MENU Button
Use this to enter the View Recording list/Disc menu.
14. ANYKEY Button
Use this to view the status of the disc that is being
played.
15. TIMER/EPG RED Button
Press this to enter the Timer Recording Mode menu.
Set the Timer Rec on the EPG.
16. MARKER/EPG GREEN Button
Press this to use Bookmarks or mark a position while
playing a disc.
Scroll up the detail information on the EPG.
17. REC Button
Use to make a recording on writable/rewritable discs.
18. EZ REC MODE Button
Use this to set the EZ REC MODE.
19. REC PAUSE Button
Press this to pause the recording.
20. INFO Button
This will display current setting or disc status.
21. INPUT SEL. Button
Selects line input signal when an external device is
connected. (Analog Ch,Digital Ch,AV1,AV2 or DV)
22. TV POWER Button
23. OPEN/CLOSE Button
To open and close the disc tray.
24. CM SKIP/SET Button
Press this to skip a portion of the program
automatically during playback of a DVD disc.
25. PLAY/PAUSE Button
Press to play/pause a disc.
26. CH Buttons
Use this to select a channel. (TV/DVD)
27. TV MUTE/AUDIO Button
This operates as Sound Mute. (TV mode)
Use this to access various audio functions on a disc.
(DVD mode)
Use this to access Multi-sound Broadcasting functions
on Air. (DTV mode)
28. RETURN Button
Returns to the previous menu.
29. PLAY LIST/TITLE MENU Button
Use this to return to the Title menu, or to view the
recorded Playlist.
30. EXIT Button
Press this to exit the menu.
31. EPG BLUE Button
Press this to go to Full / Mini Guide on the EPG.
32. CAPTION/EPG YELLOW Button
Press this to select a caption. (DTV mode)
Also used to scroll down in the EPG.
33. EPG (Electronic Program Guide) Button
Press this to display the EPG. (DTV mode)
34. CANCEL Button
35. REC MODE Button
Use this to set the desired Recording time and picture
quality. (XP/SP/LP/EP)
Ã
EPG stands for Electronic Program Guide.
Ã
This is a special remote control for the visually impaired,
and has Braille points on the POWER(
and PLAY(
English - 12
) buttons.
), STOP( )
Description
Front Panel
▌
Getting Started
1. POWER Button
Turns the recorder on and off.
2. AV 2 IN
Connect external equipment.
3. DV-IN
Connects external digital equipment with a DV
jack. (such as a camcorder)
4. DISC TRAY
Opens to accept a disc.
5. P.SCAN Button
Selects the progressive scan mode.
6. OPEN/CLOSE Button
Opens and closes the disc tray.
7. DISPLAY
Displays the playing status, time, etc.
8. DTV
Lights when a Digital channel is selected.
Front Panel Display
▌
9. INPUT SEL. Button
Selects line input signal in external mode.
(Analog Ch, Digital Ch, AV1, AV2, DV)
This allows you to select a TV signal or
connected external equipment for recording
purposes.
10. CH (
Select channels.
11. REC Button
Starts recording.
12. STOP Button
Stops disc playback.
13. PLAY/PAUSE Button
Plays a disc or pauses playback.
14. SKIP Buttons
Go to the next title/chapter/track, or go back to
/ )
the previous title/chapter/track.
1. Lights when a disc is loaded.
2. Lights in the record mode.
3. Lights to indicate the timer record mode.
4. Lights when a DVD-RAM/DVD-RW/DVD-R
disc is loaded.
5. Alpha/Numeric display.
6. Lights in the progressive scan mode.
English - 13
Rear Panel
▌
Getting Started
Fan
The fan always revolves when the power is on.
Ensure a minimum of 4” clear space on all sides of the
fan when installing the product.
1. HDMI OUT (best video quality)
Connects the input of external equipment using
a HDMI cable.
2. DIGITAL AUDIO OUT(OPTICAL)
Connects to an amplifi er having a digital optical
audio input jack.
3. DIGITAL AUDIO OUT(COAXIAL)
Connects to an amplifi er having a digital coaxial
audio input jack.
4. AV AUDIO OUT
Connect to the audio input of external
equipment using audio cables.
5. AV VIDEO OUT(good video quality)
Connects the input of external equipment using
a Video cable.
6. AV S-VIDEO OUT(better video quality)
Connects the input of external equipment using
an S-Video cable.
7. COMPONENT VIDEO OUT
(excellent video quality)
Connect to equipment having Component video
input jacks.
8. AV 1 AUDIO IN
Connect the output of external equipment using
audio cables
9. AV 1 VIDEO IN
Connects the output of external equipment
using a video cable.
10. AV 1 S-VIDEO IN
Connects the output of external equipment
using an S-Video cable.
11. ANT IN/ANT OUT (TO TV)
Connects antenna cables.
12. CABLE BOX CONTROL OUT
Connect the IR Blaster here to control your
cable box or satellite receiver (set top box).
English - 14
Connecting & Setting Up
Step 1: Connecting the Antenna Cable
There are several ways to connect your DVD Recorder. Select the antenna connection that best suits you below.
Antenna + DVD Recorder + TV
▌
You can record non-scrambled channels by selecting the channel on the DVD Recorder. Also use this method if
you watch channels without without a cable box or satellite receiver (set top box).
Connecting & Setting Up
English - 15
The VHF/UHF ANT (RF) OUT jack of this product
■
sends only signals received through the antenna.
It does not output Audio/Video signals. You must
connect Audio/Video cables to view Video from
the unit. (i.e. DVD playback)
Antenna + Cable box or satellite receiver (set top box) + DVD Recorder + TV :
▌
Cable box/Satellite receiver with a video/audio output
You can record channels by selecting the channel on the cable box or satellite receiver (set top box).
You cannot record one channel while watching another channel. Be sure that the cable box or satellite receiver
(set top box) is turned on.
Connecting & Setting Up
Connecting the IR Blaster cable into the Cable Box Control jack
The Cable Box Controller (IR Blaster) is used to control
your cable box for recording purposes.
1. Find and Connect the included IR Blaster cable into the
Cable Box's Control jack of the DVD Recorder.
2. Find the Cable Box IR Sensor
A. Turn the cable box Off.
B. Hold the Cable box/Satellite receiver's remote so that
it touches the front of the Cable box/Satellite receiver
(see Figure 1).
Figure 1
Correct
C. Move the Cable Box's remote across the front of
the Cable Box/Satellite Receiver while pressing the
remote's power button On and Off (Figure 2).
Incorrect
(Press and release the power button each time you
move the remote; holding down the button will not work.)
D. When the Cable box/Satellite receiver powers On,
you have found the sensor.
E. Remember the location of the sensor.
3. Place the IR Blaster.
Place the Cable box controller of the IR Blaster on
top or underneath the Cable box/Satellite receiver
approximately 1 inch in front of the sensor you found in 2.
Use the double-sided tape to secure the IR Blaster.
■
■
Figure 2
English - 16
You must select a Cable box/Satellite receiver
brand from the table on pages 81~83. If you do
not know the brand name, please contact your
cable/satellite provider.
After setting up your cable box or satellite receiver
(Set top box) with the DVD recorder through
IR Blaster cable, you need to set up the Set Top Box
Control menu. (See pages 32~33)
the
Antenna + Cable box or satellite receiver (set top box) + DVD Recorder + TV :
▌
Cable box/Satellite receiver with an antenna output only
You can record non-scrambled channels by selecting the channel on the DVD Recorder. You cannot record
scrambled channels that require a cable box.
Connecting & Setting Up
English - 17
Step 2 : Connecting HDMI/DVI to a TV
If your TV has an HDMI/DVI input, connect the HDMI/DVI cable to the TV. You will enjoy the best quality image
and sound.
Connecting to a TV with HDMI Jack
▌
Using an HDMI-HDMI cable, connect the HDMI OUT jack on the rear of the DVD Recorder to the HDMI IN jack of
your TV. Turn on your TV, then the DVD Recorder. Press the input selector on your TV remote control until the
HDMI signal from the DVD Recorder appears on your TV screen.
Connecting & Setting Up
To watch through the HDMI output, set the digital
■
audio output to PCM. (See page 38)
Depending on the HDMI device(TV/HDMI
■
Receiver) you use, audio may not be supported.
If your TV does not support Dolby digital/DTS,
Audio output is not available when you set the
Digital output to Bitstream or select DTS On in
the Audio setup menu. In this case, set the digital
audio ouput to PCM or DTS Off.
■
If you use an HDMI cable to connect a Samsung
TV to the DVD recorder, you can operate the
recorder using the TV remote control. (This is
only available with SAMSUNG TVs that support
Anynet+(HDMI-CEC).) (See pages 35~36)
English - 18
Please check the logo (If your TV has an
■
logo, then it supports Anynet+ function.)
Connecting to a TV with DVI Jack
▌
Using the HDMI-DVI cable (not included), connect the HDMI OUT terminal on the rear of the DVD Recorder to the
DVI IN terminal of your TV.
An HDMI to DVI connection requires a separate audio connection, using the audio cables, connect the AUDIO (red
and white) OUT terminals on the rear of the DVD Recorder to the AUDIO (red and white) IN terminals of your TV.
Turn on your TV, then the DVD Recorder.
Press the input selector on your TV remote control until the DVI signal from the DVD Recorder appears on your
TV screen.
Connecting & Setting Up
To set the HDMI output resolution (480p/720p/
■
1080i), see page 40.
HDMI (High Defi nition Multimedia Interface)
■
HDMI enables you to make a digital video and
audio connection with a single cable.
Using HDMI, the DVD player transmits a digital
video and audio signal and displays a vivid picture
on a TV having an HDMI input jack.
HDMI is completely compatible with DVI. The only
■
difference between HDMI and DVI is that HDMI
supports multi-channel audio.
HDMI connection description
■
HDMI connector - Both uncompressed video data
and digital audio data (LPCM or Bit Stream data).
- The DVD recorder outputs a pure digital signal to
the TV.
- If your TV does not support HDCP
(High bandwidth Digital Content Protection),
snow noise appears on the screen.
English - 19
Why does Samsung use HDMI?
■
Analog TVs require an analog video/audio
signal.However, when playing a DVD, the data
transmitted to a TV is digital. Therefore either a
digital-to-analog converter (in the DVD Recorder)
or an analog-to-digital converter (in the TV) is
required. During this conversion, the picture
quality is degraded due to noise and signal loss.
HDMI technology is superior because it requires
no D/A conversion and is a pure digital signal from
the DVD recorder to your TV.
What is the HDCP?
■
HDCP (High-bandwidth Digital Content Protection)
is a system for protecting DVD content output
via HDMI from being copied. It provides a secure
digital link between a video source (PC, DVD. etc)
and a display device (TV, projector. etc). Content
is encrypted at the source device to prevent
unauthorized copies from being made.
Step 3 : Connecting the Video Cable
If you have not connected to your TV via HDMI/DVI, select one of the video connections on the following pages.
Connecting to Component Video Input Jacks (Y,PB,PR)
▌
Connecting & Setting Up
1. Connect the Component video cables(not supplied)
between the COMPONENT OUT(Y,P
DVD Recorder and COMPONENT IN(Y,P
your TV (or AV amplifi er).
This connection outputs the 480i or 480p resolution to
your TV.
2. If the connected TV supports Progressive Scan, press
the P.SCAN button on the front of the DVD Recorder
to enjoy best quality video. Pressing the P.SCAN
button alternately switches the Progressive(480p) or
Interlace(480i) scan mode on.
• You will enjoy the best quality accurate color
reproduction images. Component video separates the
picture element into black and white(Y), blue(P
) signals to present clear and clean images.
red(P
R
• Connect the audio cables(white and red) between the
AUDIO OUT jacks on the DVD Recorder and AUDIO IN
jacks on your TV(or AV amplifi er).
(See pages 23~25)
) jacks on the
B,PR
B,PR
) jacks on
) and
B
English - 20
■
Compared to standard interlaced video,
progressive scan doubles the amount of video
lines fed to your TV, resulting in a clearer, more
stable, and fl icker free image than interlaced
video. The component output jack of the DVD
player can be used for progressive output mode,
which is only available with TVs that support
progressive scan.
■
Progressive Scan Output (480p).
Not all high defi nition television sets are fully
compatible with this product. If the 480p
progressive scan picture is not satisfactory, press
the P.SCAN button on the unit to switch to the
Interlace mode.
If there are questions regarding TV set
compatibility with this model, please contact our
customer service center at 1-800-SAMSUNG.
■
The Component jacks will not output video
resolutions above 480p. To view 720p and 1080i,
connect the DVD-AR650 to your TV with an HDMIHDMI cable. With HDMI connected, press the
P.SCAN button to alternate between all available
resolutions. (See page 40)
Connecting to an S-Video Input Jack
▌
Connect an S-Video cable(not supplied) between the S-VIDEO OUT jack on DVD Recorder and S-VIDEO IN jack
on your TV (or AV amplifi er).
Connecting & Setting Up
• You will enjoy high quality images. S-Video separates
the picture element into black and white (Y) and color
(C) signals to present clearer images than regular video
input mode. This connection outputs the 480i resolution
to your TV.
• Connect the audio cables(white and red) between the
AUDIO OUT jacks on the DVD Recorder and AUDIO IN
jacks on your TV(or AV amplifi er). (See pages 23~25)
English - 21
■
S-Video or Component video outputs are
available only if your TV supports S-Video input or
Component video input, respectively.
If S-Video or Component video output does not
work, check your TV connections and the TV input
selection settings.
Connecting to a Video Input Jack
▌
Connect a video(yellow) cable between the VIDEO(yellow) OUT jack on DVD Recorder and VIDEO(yellow) IN jack
on the TV (or AV amplifi er).
Connecting & Setting Up
• You will enjoy regular quality images.
• Connect the audio cables(white and red) between the
AUDIO OUT jacks on the DVD Recorder and AUDIO IN
jacks on your TV(or AV amplifi er). (See pages 23~25)
English - 22
Step 4 : Connecting the Audio Cable
Select one of the Audio connections on the following pages.
Connecting to your TV
▌
This connection will use your TV’s speakers.
Connecting & Setting Up
English - 23
Connecting to a Stereo Amplifi er with Analog Input Jacks
▌
If your stereo amplifi er only has AUDIO INPUT jacks(L and R), use the AUDIO OUT jacks on the recorder.
Connecting & Setting Up
English - 24
Connecting to an AV Amplifi er with a Digital Input Jack
▌
If your AV amplifi er has a Dolby Digital or DTS decoder and a digital input jack, use this connection. To enjoy
Dolby Digital or DTS sound, you will need to set up the audio settings. (See page 38)
Connecting & Setting Up
Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of
Dolby Laboratories.
“DTS” and “DTS Digital Out” are trademarks of DTS, Inc.
English - 25
Step 5 : Connecting External Devices
This allows you to connect your DVD Recorder to other external devices and view or record their outputs.
Connecting a VCR, Cable box/Satellite receiver (set top box) or DVD Player to the AV 1
▌
IN or S-VIDEO IN Jacks
Connecting a VCR or external device to the AV 1 IN jacks of the DVD Recorder.
You can record from connected equipment (VCR, STB or DVD Player).
Connecting & Setting Up
• You must also make audio connections when connecting
via S-Video.
English - 26
Connecting a Camcorder
▌
You can record from connected equipment, such as a camcorder by using the AV 2 IN or DV IN jacks on front of
the DVD Recorder.
Connecting & Setting Up
(See page 49)
When an Input source is inserted into AV 2 while
■
watching TV, the Input will be switched to AV 2
automatically.
If the Input is not selected automatically, press the
■
INPUT SEL. button on the remote control to select
the DV Input.
Check your camcorder's owner's manual to see
■
how to use the camcorder in this mode.
English - 27
Loading...