Samsung DV56H9100GW/A2, DV56H9100GG/A2 User Manual

DV56H9100E*

DV56H9100G*

Gas and Electric Dryer

user manual

imagine the possibilities

Thank you for purchasing this Samsung product.

DV9100HA DRY_DV56H_USER MANUAL_DC68-03170K-08_EN.indd 1 2016/2/25 16:36:51

contents

INSTALLING YOUR DRYER

7 Unpacking your dryer 7 Basic requirments 8 Ducting requirements 9 Important to installer 9 Location considerations 9 Alcove or closet installation 11 Exhausting 12 Gas requirements 12 Commonwealth of Massachusetts

installation instructions

13 Electrical requirements 13 Grounding 14 Electrical connections 15 Installation - General procedure 18 Connecting the Inlet Hose 18 Final installation check list 19 Dryer Exhaust Tips 20 Door Reversal

OPERATING INSTRUCTIONS, TIPS

CARE AND CLEANING

SPECIAL LAUNDRY TIPS

TROUBLESHOOTING

22 Overview of the control panel

25 Rack Dry 26 My Cycle 26 Drum Light

26 Sound

26 Child lock 27 Smart Care

27 Clean the lint ﬁlter 27 Load the dryer properly 27 Getting started

27 Vent sensor

30 Control Panel 30 Tumbler 30 Powder Coated Tumbler 30 Dryer Exterior 30 Dryer Exhaust System

31 Special laundry tips

32 Check these points if your dryer… 33 Information codes

APPENDIX

English - 2

DV9100HA DRY_DV56H_USER MANUAL_DC68-03170K-08_EN.indd 2 2016/2/25 16:36:51

34 Fabric care chart 35 Protecting the environment 35 Declaration of conformity 35 Speciﬁcations 36 Cycle chart

safety instructions

Congratulations on your new Samsung Dryer. This manual contains valuable information on the installation, use, and care of your appliance. Please take the time to read this manual to take full advantage of your dryer’s many beneﬁts and features.

WHAT YOU NEED TO KNOW ABOUT SAFETY INSTRUCTIONS

Warnings and Important Safety Instructions in this manual do not cover all possible conditions and situations that may occur. It is your responsibility to use common sense, caution, and care when installing, maintaining, or operating your dryer.

Always contact your manufacturer about problems or conditions you do not understand.

IMPORTANT SAFETY SYMBOLS AND PRECAUTIONS

What the icons and signs in this user manual mean:

Hazards or unsafe practices that may result in severe personal injury or death.

WARNING

Follow the information in this manual to minimize the risk of ﬁre or explosion or to prevent property damage, personal injury, or death.

Do not store or use gasoline or other ﬂammable vapors and liquids near this or any other appliance.

CAUTION

These warning icons are here to prevent injury to you and others. Please follow them explicitly. After reading this section, keep it in a safe place for future reference.

Read all instructions before using the appliance.

Hazards or unsafe practices that may result in minor personal injury or property damage.

Do NOT attempt.

Do NOT disassemble.

Do NOT touch.

Follow directions explicitly.

Unplug the power plug from the wall socket.

Make sure the machine is grounded to prevent electric shock.

Call the service center for help.

Note

English - 3

DV9100HA DRY_DV56H_USER MANUAL_DC68-03170K-08_EN.indd 3 2016/2/25 16:36:51

safety instructions

WARNING: To reduce the risk of ﬁre, electric shock, or injury to persons when using your

WARNING

appliance, follow basic precautions, including the following:

1. Read all instructions before using this appliance.

2. Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, or other ﬂammable or explosive substances, as they give o vapors that could ignite or explode.

3. Do not use the dryer to dry clothes which have traces of any ﬂammable substance, such as vegetable oil, cooking oil, machine oil, ﬂammable chemicals, paint thinner, etc., or anything containing wax or chemicals, such as mops and cleaning cloths. Flammable substances may cause the fabric to catch ﬁre by itself.

4. Do not store or use gasoline or other ﬂammable vapors and liquids near this or any other appliance.

5. Do not allow children to play on or in the appliance. Close supervision of children is necessary when the appliance is used near children.

6. Before the appliance is removed from service or discarded, remove the door to the drying compartment.

7. Do not reach into the appliance if the drum is moving.

8. Do not install or store this appliance where it will be exposed to the weather.

9. Do not tamper with internal controls.

10. Do not repair or replace any part of the appliance or attempt any service unless speciﬁcally recommended in the user-maintenance instructions or in published userrepair instructions that you understand and have the skills to carry out.

11. Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product.

12. Clean the lint screen before or after each load.

13. Do not use heat to dry articles containing foam rubber or similarly textured rubber-like materials.

14. Keep area around the exhaust opening and adjacent surrounding areas free from the accumulation of lint, dust, and dirt.

15. The interior of the appliance and exhaust duct should be cleaned periodically by qualiﬁed service personnel.

16. Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch ﬁre.

17. This appliance must be grounded. See “Electrical requirements” and ”Grounding” in installing your dryer section.

18. Do not allow children to play on or in the appliance. Close supervision of children is necessary when the appliance is used near children.

19. Do not insert your hand under the dryer.

- This may result in injury.

20. Take care that children’s ﬁngers are not caught in the door when closing it.

- This may result in injury.

21. Control board and inlet valve are intentionally not grounded and may present a risk of electric shock only during servicing.

- Do not contact this part while appliance is energized.

English - 4

DV9100HA DRY_DV56H_USER MANUAL_DC68-03170K-08_EN.indd 4 2016/2/25 16:36:51

WARNING -

• State of California Proposition 65 Warnings (US only)

This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

• Gasappliancescancauselow-levelexposuretoProposition65listed

substances, including but not limited to, benzene, carbon monoxide, formaldehyde and soot, substances resulting from the incomplete combustion of natural gas or LP fuels.

Gas Appliances:

WARNING - Risk of Fire

• Clothesdryerinstallationmustbeperformedbyaqualiedinstaller.

• Installtheclothesdryeraccordingtothemanufacturer’sinstructionsandlocalcodes.

• Donotinstallaclothesdryerwithexibleplasticventingmaterials.Ifexiblemetal

(foil type) duct is installed, it must be of a speciﬁc type identiﬁed by the appliance manufacturer as suitable for use with clothes dryers. Flexible venting materials are known to collapse, be easily crushed, and trap lint. These conditions will obstruct clothes dryer airﬂow and increase the risk of ﬁre.

• Toreducetheriskofsevereinjuryordeath,followallinstallationinstructions.

To reduce the risk of ﬁre or explosion:

WARNING

• Do not dry items that have been previously cleaned, washed, soaked, or spotted with gasoline, dry cleaning solvents, or other ﬂammable or explosive substances. They emit vapors that could ignite or explode. Any material that has been in contact with a cleaning solvent or ﬂammable liquids or solids should not be placed in the dryer until all traces of these ﬂammable liquids or solids and their fumes have been removed. There are many highly ﬂammable items used in homes, such as acetone, denatured alcohol, gasoline, kerosene, some liquid household cleaners, some spot removers, turpentine, waxes, and wax removers.

• Items containing foam rubber (may be labeled latex foam) or similarly textured rubberlike materials must not be dried on a heat setting. Heated foam rubber materials can, under certain circumstances, produce ﬁre by spontaneous combustion.

What to do if you smell gas:

WARNING

• Donottrytolightanyappliance.

• Donotturnontheappliance.

• Donottouchanyelectricalswitch.

• Donotuseanyphoneinyourbuilding.

• Cleartheroom,buildingorareaofalloccupants.

• Immediatelycallyourgassupplierfromaneighbor’sphone.Followthegassupplier’s

instructions.

• Ifyoucannotreachyourgassupplier,calltheredepartment.

• Installationandservicemustbeperformedbyaqualiedinstaller,serviceagency,orthe

gas supplier.

English - 5

DV9100HA DRY_DV56H_USER MANUAL_DC68-03170K-08_EN.indd 5 2016/2/25 16:36:51

safety instructions

Do not allow children or pets to play on, in, or in front of the appliance. Close supervision is necessary when the appliance is used near children and pets.

Before discarding or removing your dryer from service, remove the door to the drying compartment to prevent children or animals from becoming trapped inside.

Do not reach into the appliance when the drum is moving. Do not install or store this appliance where it will be exposed to the weather. Do not tamper with controls. Do not repair, replace, or attempt to service any part of the appliance unless speciﬁcally

instructed to in the user-repair instructions and you have the understanding and skills to carry out the procedure.

Do not use fabric softeners or products to eliminate static unless the softener or product is recommended for dryer use by the manufacturer of the fabric softener or product.

Clean the lint screen before or after each load. Keep the area around the exhaust opening and surrounding areas free from lint, dust, and dirt. The interior of the dryer and exhaust duct should be cleaned periodically by qualiﬁed service

personnel. This appliance must be properly grounded. Never plug the power cord into a receptacle

that is not grounded adequately or not in accordance with local and national codes. See installation instructions for information about grounding this appliance.

Do not sit on top of the dryer. Ensure pockets are free from small, irregularly shaped hard objects, foreign material, etc. ie.

WARNING

coins, knives, pins, etc. These objects could damage your dryer. Do not wash clothing with large buckles, buttons, or other heavy metal or solid objects. Gas leaks may occur in your system, resulting in a dangerous situation.

WARNING

Gas leaks may not be detected by smell alone. Gas suppliers recommend you purchase and install a UL-approved gas detector. Install and use in accordance with the manufacturer’s instructions. Do not place items in your dryer that have been spotted or soaked with vegetable oil or cooking

oil. Even after being washed, these items may contain signiﬁcant amounts of these oils. Residual oil on clothing can ignite spontaneoulsy. The potential for spontaneous

combustion increases when items containing vegetable oil or cooking oil are exposed to heat. Heat sources such as your dryer can warm these items, allowing an oxidation reaction in the oil to occur. Oxidation creates heat. If this heat cannot escape, the items can become hot enough to catch ﬁre. Piling, stacking, or storing these kinds of items may prevent heat from escaping and can create a ﬁre hazard.

All washed and unwashed fabrics that contain vegetable oil or cooking oil can be dangerous. Washing these items in hot water with extra detergent will reduce, but not eliminate, the hazard. Always use the Cool Down cycle for these items to reduce their temperature. Never remove these items from the dryer hot or interrupt the drying cycle until the items have run through the Cool Down cycle. Never pile or stack these items when they are hot.

English - 6

DV9100HA DRY_DV56H_USER MANUAL_DC68-03170K-08_EN.indd 6 2016/2/25 16:36:51

installing your dryer

UNPACKING YOUR DRYER

Unpack your dryer and Inspect it for shipping damage. Make sure you have received all of the items shown below. If your dryer was damaged during shipping, or you do not have all of the items, contact 1-800-SAMSUNG (726-7864).

To prevent personal injury or strain, wear protective gloves whenever lifting or carrying the dryer.

Packing materials can be dangerous to children. Keep all packing material (plastic bags, polystyrene,

WARNING

etc.) well out of children’s reach.

01 installing your dryer

Tools needed

Pliers Cutting knife Pipe wrench (gas only) Nut drivers

Frame Front

Filter

Top Cover

Control panel

[ BACK ]

Door

Duct Exhaust

Level Phillips Screwdriver Duct tape Wrench

Parts supplied

“Y”- Connector Hose water Short inlet hose

BASIC REQUIRMENTS

Make sure you have everything necessary for proper installation

• A GROUNDED ELECTRICAL OUTLET is required. See Electrical Requirements.

• A POWER CORD for electric dryers (except in Canada).

• GAS LINES (if installing a gas dryer). The gas lines must meet national and local codes.

• EXHAUST SYSTEM - must be rigid metal or ﬂexible sti-walled metal exhaust ducting.

English - 7

DV9100HA DRY_DV56H_USER MANUAL_DC68-03170K-08_EN.indd 7 2016/2/25 16:36:53

installing your dryer

DUCTING REQUIREMENTS

• Use a 4-inch (10.2 cm) diameter rigid aluminum or rigid galvanized steel duct.

• Do not use a smaller duct.

• Ducts larger than 4 inches (10.2 cm) in diameter can cause increased lint accumulation.

Lint accumulation should be cleaned regularly.

• If a ﬂexible metal duct must be used, use the type with a sti sheet metal wall. Do not use a ﬂexible duct with a thin foil wall. Serious blockage can result if the ﬂexible metal duct is bent too sharply.

• Never install any type of ﬂexible duct in walls, ceilings, or other concealed spaces.

• Keep the exhaust duct as straight and short as possible.

• Secure joints with duct tape. Do not use screws.

• Plastic ﬂexible duct can kink, sag, be punctured, reduce airﬂow, extend drying times, and aect dryer

operation.

• Exhaust systems longer than recommended can extend drying times, aect machine operation, and may collect lint.

• The exhaust duct should end with an exhaust hood with a swing-out damper to prevent back drafts and the entry of wildlife. Never use an exhaust hood with a magnetic damper.

• The hood should have at least 12 inches (30.5 cm) of clearance between the bottom of the hood and the ground or other obstruction. The hood opening should point down.

• Never install a screen over the exhaust outlet.

• To avoid lint buildup, do not exhaust the dryer directly into a window well. Do not exhaust under a house

or porch.

• If exhaust ductwork must run through an unheated area, the duct should be insulated and slope slightly down towards the exhaust hood to reduce condensation and lint buildup.

• Inspect and clean the interior of the exhaust system at least once a year. Unplug the power cord before cleaning.

• Check frequently to be sure the exhaust hood damper opens and closes freely.

• Check once per month, and clean at least one time per year. Note: If clothes are not getting dry, then

check ducting for obstructions.

• Do not exhaust dryer into any wall, ceiling, crawl space, or concealed space of a building, gas vent, or any other common duct or chimney. This could create a ﬁre hazard from lint expelled by the dryer.

ELECTRIC AND GAS DRYER

Weather Hood Type

Recommended Use only for short-run installation

4” (10.2 cm) 2.5” (6.4 cm)

No. of 90° elbows Rigid Metallic Flexible* Rigid Metallic Flexible*

0 80 ft. (24.4 m) 41 ft. (12.4 m) 74 ft. (22.6 m) 33 ft. (10.1 m) 1 68 ft. (20.7 m) 37 ft. (11.2 m) 62 ft. (18.9 m) 29 ft. (8.8 m) 2 57 ft. (17.4 m) 33 ft. (10.1 m) 51 ft. (15.5 m) 25 ft. (7.6 m) 3 47 ft. (14.3 m) 29 ft. (8.8 m) 41 ft. (12.5 m) 21 ft. (6.5 m)

* Do not use non-metallic ﬂexible duct.

English - 8

DV9100HA DRY_DV56H_USER MANUAL_DC68-03170K-08_EN.indd 8 2016/2/25 16:36:53

If the new dryer is being installed into an existing exhaust system, you must make sure:

• The exhaust system meets all local, state, and national codes.

• That a ﬂexible plastic duct is not used.

• To Inspect and clean all lint buildup from inside the existing duct.

• The duct is not kinked or crushed.

• The exhaust hood damper opens and closes freely.

The static pressure in any exhaust system must not exceed 0.83 inches of water column, or be less than 0.

This can be measured with the dryer running with a manometer at the point where the exhaust duct connects to the dryer. A no-heat setting should be used. The dryer tumbler should be empty and the lint ﬁlter clean.

IMPORTANT TO INSTALLER

Please read the following instructions carefully before installing the dryer. These instructions should be kept for future reference.

Remove the door from all discarded appliances to avoid the danger of a child suocating.

WARNING

LOCATION CONSIDERATIONS

Locate the dryer where there is enough space at the front for loading the dryer, and enough space behind for the exhaust system. This dryer is factory-ready for rear exhaust. To exhaust out the bottom or the right or the left (electric model only), use the accessory exhaust kit (sold separately). Instructions are included with the kit. It’s important to make sure the room has enough fresh air. The dryer must be located where there is no air-ﬂow obstruction.

On gas dryers, adequate clearance as noted on the data plate must be maintained to ensure adequate air for combustion and proper dryer operation.

Do not install or store the dryer in an area where it will be exposed to water and/or weather. Keep the dryer area clear of combustible materials, gasoline, and other ﬂammable vapors and liquids. A dryer produces combustible lint. The area around the dryer should be kept lint free.

01 installing your dryer

ALCOVE OR CLOSET INSTALLATION

MINIMUM CLEARANCES FOR CLOSET AND ALCOVE INSTALLATIONS:

Sides – 1 in / 25 mm Rear – 5 in / 127 mm If the washer and dryer are installed together, the closet front must have at least a 72 in² (465 cm²)

unobstructed air opening. Your washer alone does not require a speciﬁc air opening. A. Recessed area B. Side view - closet or conﬁned area

1 in.

(2.5 cm)

1 in.

(2.5 cm)

30 in.

(76.2 cm)

30 in.

(76.2 cm)

(2.5 cm)

Top – 17 in / 432 mm Closet Front – 2 in / 51 mm

1 in.

English - 9

(5 cm)

2 in.

17 in.

(43.2 cm)

32 in.

(81.3 cm)

5 in.

(12.7 cm)

DV9100HA DRY_DV56H_USER MANUAL_DC68-03170K-08_EN.indd 9 2016/2/25 16:36:53

installing your washer

With optional pedestal base or stacking kit

Required Dimensions for Installation With Pedestal (Model No.: WE302*)

57.8 in. (146.7 cm) to clear open door

(12.7 cm)

3 in.

(7.6 cm)

5 in.

30 in.

(76.2 cm)

48 in.² *

(310 cm²)

32 in.

(81.3 cm)

42.6 in.

(108.3cm)

53.7 in.

(136.5 cm)

5 in.

(12.7 cm)

24 in.² *

(155 cm²)

Closet or Door

3 in.

(7.6 cm)

1 in.

(2.5 cm)

32.5 in.

(82.6 cm)

7.5 in.** (19 cm)

Required Dimensions for Installation With Stacking Kit (Model No.: SKK-BB)

6 in. *

(15.2 cm)

84.6 in.

(215 cm)

* Required spacing

1 in.

(2.5 cm)

30 in.

(76.2 cm)

** External exhaust elbow requires

additional space.

English - 10

DV9100HA DRY_DV56H_USER MANUAL_DC68-03170K-08_EN.indd 10 2016/2/25 16:36:54

EXHAUSTING

The dryer shall not be exhausted into a chimney, a wall, a ceiling, an attic, a crawl space, or a concealed space of a building.

Exhausting the dryer to the outside will prevent large amount of lint and moisture from being blown into the room.

In the United States:

• All dryers must be exhausted to the outside.

• The required exhaust duct is 4 inches (10.2 cm) in diameter.

• Use only those foil-type ﬂexible ducts, if any, speciﬁcally identiﬁed for use with the appliance

by the manufacturer and that comply with the Outline for Clothes Dryer Transition Duct, Subject 2158A shall be used.

• See “Ducting Requirements” in installing your dryer section for the maximum duct length and number of bends shall be used.

• The total length of ﬂexible metal duct shall not exceed 2.4 m.

• Do not assemble the duct with screws or other fastening means that extend into the duct

and catch lint

In Canada:

• All dryer must be exhausted to the outside.

• The exhaust duct should be 4 inches (10.2 cm ) in diameter.

• Use only those foil-type ﬂexible ducts, if any, speciﬁcally indentiﬁed for use with the appliance

by the manufacturer shall be used.

• See “Ducting Requirements” in installing your dryer section for the maximum duct length and number of bends.

• The total length of ﬂexible metal duct shall not exceed 2.4 m.

• Do not assemble the duct with screws or other fastening means that extend into the duct

and catch lint.

01 installing your dryer

Outside the U.S. and Canada:

• Refer to the local codes.

You must exhaust the dryer to the outside to reduce the risk of ﬁre when you install the dryer in an alcove or closet.

WARNING

NEVER USE A PLASTIC OR NON-METAL FLEXIBLE DUCT. If your existing ductwork is plastic, non-metal, or combustible, replace it with metal. Use only a metal exhaust duct that is non-ﬂammable to ensure containment of exhaust air, heat, and lint.

English - 11

DV9100HA DRY_DV56H_USER MANUAL_DC68-03170K-08_EN.indd 11 2016/2/25 16:36:54

installing your dryer

GAS REQUIREMENTS

Use only natural or LP (liquid propane) gases.

THE INSTALLATION MUST CONFORM WITH LOCAL CODES, OR IN THE ABSENCE OF LOCAL CODES, WITH THE NATIONAL FUEL GAS CODE ANSI/Z223.1, LATEST REVISION (FOR THE UNITED STATES), OR WITH THE CAN/CGA-B149 INSTALLATION CODES (FOR CANADA).

Gas dryers are equipped with a burner vent for use with natural gas. If you plan to use your dryer with LP (liquid propane) gas, it must be converted for safe and proper performance by a qualiﬁed service technician.

A 1/2” (1.27 cm) gas supply line is recommended and must be reduced to connect to the 3/8” (1 cm) gas line on your dryer. The National Fuel Gas Code requires that an accessible, approved manual gas shut-o valve be installed within 6” of your dryer.

Gas dryers installed in residential garages must be raised 18 inches (46 cm) above the ﬂoor.

Additionally, a 1/8” (0.3 cm) N.P.T. (National Pipe Thread) plugged tapping, accessible for test gauge connection, must be installed immediately upstream of your dryer’s gas supply connection.

Your dryer must be disconnected from the gas supply pipe system during any pressure testing of the system.

DO NOT reuse old ﬂexible metal gas lines. Flexible gas lines must be design certiﬁed by the American Gas Association (CGA in Canada).

• Any pipe joint compound used must be resistant to the action of any liqueﬁed petroleum gas.

• As a courtesy, most local gas utilities will Inspect a gas appliance installation.

GAS IGNITION – Your dryer uses an automatic ignition system to ignite the burner.

There is no constant burning pilot.

COMMONWEALTH OF MASSACHUSETTS INSTALLATION INSTRUCTIONS

Your dryer must be installed by a licensed plumber or gas ﬁtter. A “T” handle manual gas valve must be installed in the gas supply line to your dryer. If a ﬂexible gas connector is used to install your dryer, the connector can be no longer than 3’ (36”).

• Gas leaks may occur in your system, creating a dangerous situation.

• Gas leaks may not be detected by smell alone.

WARNING

• Gas suppliers recommend you purchase and install a UL-approved gas detector.

• Install and use in accordance with the manufacturer’s instructions.

English - 12

DV9100HA DRY_DV56H_USER MANUAL_DC68-03170K-08_EN.indd 12 2016/2/25 16:36:54

ELECTRICAL REQUIREMENTS

The wiring diagram is located on the plate below the control panel or frame back.

• Improperly connecting the equipment grounding conductor can result in a risk of electric shock.

WARNING

Check with a qualiﬁed electrician or serviceman if you are in doubt as to whether your dryer is properly grounded. Do not modify the plug provided with your dryer – if it doesn’t ﬁt the outlet, have a proper outlet installed by a qualiﬁed electrician.

• To prevent unnecessary risk of ﬁre, electrical shock, or personal injury, all wiring and grounding must be done in accordance with local codes, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA No. 70-Latest Revision (for the U.S.) or the Canadian Electrical Code CSA C22.1 – Latest Revisions and local codes and ordinances. It is your responsibility to provide adequate electrical services for your dryer.

• All gas installations must be done in accordance with the national Fuel Code ANSI/Z2231 – Latest Revision (for the U.S.) or CAN/CGA – B149 Installation Codes – Latest Revision (for Canada) and local codes and ordinances.

GROUNDING

This dryer must be grounded. In the event of malfunction or breakdown, the ground will reduce the risk of electrical shock by providing a path of least resistance for the electrical current.

Gas models

WARNING

Your dryer has a cord with an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in

accordance with all local codes and ordinances. Do not modify the plug provided with your dryer – if it doesn’t ﬁt the outlet, have a proper outlet

installed by a qualiﬁed electrician. Never connect the ground wire to plastic plumbing lines, gas lines, or hot water pipes.

01 installing your dryer

Electric models

WARNING

Your dryer has an optional cord with an equipment-grounding conductor and a grounding plug. This cord is sold separately.

The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Do not modify the plug provided with your dryer – if it doesn’t ﬁt the outlet, have a proper outlet installed by a qualiﬁed electrician.

If a power cord is not used and the electric dryer is to be permanently wired, the dryer must be connected to a permanently grounded metal wiring system, or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment grounding terminal or lead on the dryer.

English - 13

DV9100HA DRY_DV56H_USER MANUAL_DC68-03170K-08_EN.indd 13 2016/2/25 16:36:54

installing your dryer

ELECTRICAL CONNECTIONS

Before operating or testing, follow all grounding instructions in the grounding section. An individual branch (or separate) circuit serving only your dryer is recommended. DO NOT USE AN

EXTENSION CORD.

Gas models – U.S. and Canada

A 120 volt, 60 Hz AC approved electrical service, with a 15-ampere fuse or circuit breaker is required.

Electric models – U.S. only

Most U.S. dryers require a 120 / 240 volt, 60 Hz AC approved electrical service. Some require 120 / 208 volt, 60 Hz approved electrical service. The electric service requirements can be found on the data label located behind the door. A 30-ampere fuse or circuit breaker on both sides of the line is required.

• If a power cord is used, the cord should be plugged into a 30-ampere receptacle.

• The power cord is NOT provided with U.S. electric model dryers.

Risk of Electric Shock

WARNING

When local codes allow, the dryer electrical supply may be connected by means of a new power supply cord kit, marked for use with a dryer, that is U.L. listed and rated at a minimum of 120/240 volts, 30-ampere with three No. 10 copper wire conductors terminated with closed loop terminals, open-end spade lugs with turned up ends, or with tinned leads.

• Do not reuse a power supply cord from an old dryer. The power cord electric supply wiring must be supported at the dryer cabinet by a suitable UL-listed strain relief.

• Grounding through the neutral conductor is prohibited for (1) new branch-circuit installations, (2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding through the neutral conductor. (Use a 4-prong plug for a 4 wire receptacle, NEMA type 14-30R.)

Electric models – Canada Only

• A 120 / 240 volt, 60 Hz AC approved electrical service fused through a 30-ampere fuse or circuit breaker on both sides of the line is required.

• All Canadian models are shipped with the power cord attached. The power cord should be plugged into a 30-ampere receptacle.

It is not permissible to convert a dryer in Canada to 208 volts.

English - 14

DV9100HA DRY_DV56H_USER MANUAL_DC68-03170K-08_EN.indd 14 2016/2/25 16:36:54

INSTALLATION - GENERAL PROCEDURE

For proper installation, we recommend that you hire a qualiﬁed installer.

Read these instructions completely before you begin the installation.

To install the dryer, follow these steps:

1. Move your dryer to an appropriate location for installation. Consider installing the dryer and washer side-

by-side so you have easy access to both appliances.

To move the dryer easily, lay two of the carton cushion-tops on the ﬂoor. Tip your dryer on its side so it lies across both cushion-tops. Push the dryer so that it is near its ﬁnal location. Set your dryer upright. Leave enough room around the dryer so you can attach the duct work, power cord, etc.

2. If you need to change the direction of the door, go to Door Reversal on page 20. When done, return to

Step 3 below.

3. Review the exhausting section before installing the exhaust system. Install the duct work from your dryer

to the exhaust hood. The crimped end of the duct sections must point away from your dryer. DO NOT use sheet metal screws when assembling ducting. These joints should be taped. Never use plastic ﬂexible exhaust material.

A tip for tight installations: Attach a section of the exhaust system to your dryer before putting it in place. Use duct tape to secure this section to your dryer, but do not cover the ventilation slots at the back of the dryer cabinet.

4. If you have an electric model, skip to Step 6. If you have a gas model, go to the next step.

5. Review the Gas Requirements section, then follow the lettered steps below. a. Remove the pipe thread protective cap. b. Apply pipe joint compound or about 1 1/2 wraps of Teﬂon tape over all threaded connections.

01 installing your dryer

The pipe joint compound must be resistant to the action of any liqueﬁed petroleum gas.

c. Connect the gas supply to your dryer. An additional ﬁtting is required to connect the 3/4” (1.9 cm)

female thread end of a ﬂexible connector to the 3/8” (1 cm) male threaded end on the dryer.

d. Securely tighten the gas line ﬁtting over the threads. e. Turn on the gas supply. Check all gas connections for leaks using a soap solution. If bubbles

appear, tighten the connections and recheck. DO NOT use an open ﬂame to check for gas leaks.

f. Go to Step 6 on the next page

English - 15

DV9100HA DRY_DV56H_USER MANUAL_DC68-03170K-08_EN.indd 15 2016/2/25 16:36:54

installing your dryer

6. Review the Electrical Requirements section, then follow the 3 Wire system connection instructions (Step

7) or 4 Wire system instructions (Step 8) below.

7. Three Wire system instructions: A. External ground connector B. Neutral grounding wire (white) C. Center silver-colored terminal block screw D. Neutral wire (white or center wire) E. ¾” (1.9 cm) UL-listed strain relief

1. Loosen or remove the center terminal block screw.

2. Connect the neutral wire (white or center wire) of the power

cord to the center, silver-colored terminal screw of the terminal block. Tighten screw.

3. Connect the other wires to outer terminal block screws. Tighten screws.

4. Tighten the strain relief screws.

5. Insert the tab of the terminal block cover into your dryer’s rear panel slot.

Secure the cover with a hold-down screw.

If converting from a 4-wire electrical system to a 3-wire, you must connect the ground strap to the terminal block support to ground the dryer frame to the neutral conductor.

WARNING

We recommend using ring terminals. If you use strap terminals, please ensure you install them perfectly.

8. Four Wire System instructions: A. External ground connector B. Green or bare copper wire of power cord C. ¾” (1.9 cm) UL-listed strain relief D. Center silver-colored terminal block screw E. Neutral grounding wire (white) F. Neutral wire (white or center wire)

1. Remove the External ground connector screw.

2. Connect the ground wire (green or unwrapped) of the

power cord to the external ground connector screw. If you want to connect B (Green or bare copper wire of power cord) to the Neutral Post without connecting it to A (cabinet ground), call a service technician.

3. Loosen or remove the center terminal block screw.

4. Connect the neutral wire (white or center wire) of the power cord and the appliance ground

wire (green with yellow stripes) under the central screw of the terminal block.

5. Connect the other wires to the outer terminal block screws. Tighten screws.

6. Tighten the strain relief screws.

7. Insert the tab of the terminal block cover into your dryer’s rear panel slot.

Secure the cover with a hold-down screw.

We recommend using ring terminals. If you use strap terminals, please ensure you install them perfectly.

English - 16

DV9100HA DRY_DV56H_USER MANUAL_DC68-03170K-08_EN.indd 16 2016/2/25 16:36:54

U.S. MODELS:

Risk Of Electric Shock

WARNING

All U.S.models are designed for a 3-WIRE SYSTEM CONNECTION. The dryer frame is grounded to the neutral conductor at the terminal block. A 4-WIRE SYSTEM CONNECTION is required for new or remodeled construction, mobile homes, or if local codes do not permit grounding through neutral. If you use the 4-wire system, you cannot ground the dryer frame to the neutral conductor at the terminal block.

Remove the terminal block cover plate. Insert the power cord with a UL-listed strain relief through the hole provided in the cabinet near the terminal block.

A strain relief must be used. Do not loosen the nuts already installed on the terminal block. Be sure they are tight. Use a 3/8” (1cm) deep well socket.

9. To ensure that the dryer provides optimal drying performance, it must

be level. To level the dryer, follow the lettered steps below:

Level

a. Using a level, check if the dryer is level side to side and then front

to back.

b. If the dryer is not level, adjust the leveling feet on the bottom of

the dryer until the dryer is level side to side and back to front. Turning the feet clockwise retracts the feet. Turning the feet clockwise loosens and extends them.

If you have a dryer and washer

To set the dryer to the same height as the washer, fully retract the leveling feet by turning them counterclockwise, then loosen the feet by turning them clockwise. Once the dryer is the same height as the washer, follow the directions above to level the dryer.

01 installing your dryer

Leveling feet

Retract fully Then loosen

Adjust the leveling feet only as much as necessary to level the dryer. Extending the leveling feet more than necessary can cause the dryer to vibrate.

10. Make sure all gas connections (on gas models) and exhaust, and electrical connections are complete.

Plug in your dryer, and then check its operation by using the checklist on the next page.

11. For GAS MODELS ONLY

The burner may not ignite initially due to air in the gas line. Allowing your dryer to operate on a heat setting will purge the line. If the gas does not ignite within 5 minutes, turn your dryer o and wait 5 minutes. Be sure the gas supply to your dryer has been turned on. To conﬁrm gas ignition, check the exhaust for heat.

English - 17

DV9100HA DRY_DV56H_USER MANUAL_DC68-03170K-08_EN.indd 17 2016/2/25 16:36:54

installing your dryer

CONNECTING THE INLET HOSE

METHOD1

The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old hoses.

1. If space permits, attach the brass female end of the “Y” connector to the cold water faucet.

2. Turn the cold water faucet o.

3. Attach the straight end of long hose to “Y’ connector.

4. Using pliers, tighten the coupling with an additional two-thirds turn.

Do not overtighten, as it may damage the coupling.

5. Attach angled end of long hoses to ﬁll the valve at the

bottom of the dryer’s rear frame. Screw on coupling by hand until it is seated on ﬁll valve connector.

6. Using pliers, tighten the coupling with an additional two-thirds turn.

Do not overtighten, as it may damage the coupling.

7. Check that the water faucets are on.

8. Check for leaks around “Y” connector, faucets and hoses.

METHOD2

The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old hoses.

1. If “Y” connector cannot be attached directly to the cold water

faucet, the short hose must be used.

2. Turn the cold water faucet o.

3. Attach short inlet hose to cold water faucet.

Screw on coupling by hand until it is seated on the faucet.

4. Using pliers, tighten the coupling with an additional

two-thirds turn. Do not overtighten, as it may damage the coupling.

5. Attach ‘Y” connector to brass male end of small hose.

Screw on coupling by hand until it is seated on connector.

6. Using pliers, tighten the coupling with an additional two-thirds turn.

Do not overtighten, as it may damage the coupling.

7. Attach angled end of long hoses to the ﬁll valve at the bottom of the dryer rear frame. Screw on

coupling by hand until it is seated on ﬁll valve connector.

8. Using pliers, tighten the coupling with an additional two-thirds turn.

Do not overtighten, as it may damage the coupling.

9. Check that the water faucets are on.

10. Check for leaks around “Y” connector, faucets and hoses.

.UYK]GZKX

9NUXZOTRKZNUYK

?)UTTKIZUX

FINAL INSTALLATION CHECK LIST

 The dryer is plugged into an electrical outlet and grounded properly.  The exhaust ductwork is hooked up and the joints are taped.  You have used rigid or sti-walled ﬂexible metal duct material, not plastic ﬂexible duct.  The dryer is level and is sitting ﬁrmly on the ﬂoor.  For gas models: The gas is turned on and there are no gas leaks.  Start your dryer to conﬁrm that it runs, heats, and shuts o.

English - 18

DV9100HA DRY_DV56H_USER MANUAL_DC68-03170K-08_EN.indd 18 2016/2/25 16:36:55

DRYER EXHAUST TIPS

Plastic or non-metal ﬂexible duct presents a potential ﬁre hazard.

WARNING

1. Make sure your dryer is installed properly so it exhausts air

easily.

2. Use 4” diameter rigid metal duct. Tape all joints, including at

the dryer. Never use lint-trapping screws.

3. Keep ducts as straight as possible.

4. Clean all old ducts before installing your new dryer.

Be sure the vent ﬂap opens and closes freely. Inspect and clean the exhaust system annually.

Dryer

DUCT

Wall

DUCT EXHAUST

Tape

01 installing your dryer

Don’t let a poor exhaust system slow drying by:

1. Restricting your dryer with a poor exhaust system.

2. Using a plastic, thin foil, or non-metal ﬂexible duct.

3. Using unnecessarily long ducts that have many

elbows.

4. Using crushed or clogged venting or ducts.

English - 19

DV9100HA DRY_DV56H_USER MANUAL_DC68-03170K-08_EN.indd 19 2016/2/25 16:36:55

1 2

3 4

RING-E

installing your dryer

DOOR REVERSAL

If you want to reverse the direction of the door, it is recommended calling a qualiﬁed service technician.

1. Unplug the power cord.

2. Remove the one screw from the COVER HANDLE.

3. Remove the 7 screws (M5, M4 2type) from the BRACKET DOOR.

4. Remove DOOR from BRACKET DOOR.

5. Remove the RINE-E and PIN from the BRACKET DOOR.

6. Remove the BRACKET DOOR from the HINGE.

7. Remove the 4 screws (M4 2EA, M5 2EA), HOLDER LEVER, COVER

HINGE, BRACKET LEVER from the left side of FRONT.

Push the COVER HINGE strongly when you disassemble screws

WARNING

on COVER HINGE from the left side of FRONT. LEVER LINK will be appear by spring if you don’t push COVER HINGE. Assemble the BRACKET DOOR, PIN and RING-E on the opposite side

using the PIN that were removed in Step 4.

Use to remove COVER HOLDER LEVER With (-) driver.

8. Remove the 2 screws and COVER HOLDER LEVER from the right side

of FRONT.

9. Assemble the HOLDER LEVER, COVER HINGE, BRACKET LEVER and

COVER HOLDER LEVER on the opposite side using the screws that were removed from the left side in Step-7,8.

DV9100HA DRY_DV56H_USER MANUAL_DC68-03170K-08_EN.indd 20 2016/2/25 16:36:57

English - 20

10. Remove the the 9 screws. (L12 1ea, L14 5 ea, L18 2 ea).

11. Remove the COVER HANDLE and LEVER DOOR.

12. Remove the the 1 screw(L14).

13. Rotate the HOLDER GLASS (BIG ROUNDED STEEL) 180º.

14. Assemble the the 1 screw (L14).

L12

L14

COVER HANDLE

L18

LEVER DOOR

01 installing your dryer

15. Assemble the COVER HANDLE and LEVER DOOR on the

HOLDER GLASS.

16. Assemble the 9 screws. (L12 1ea, L14 5 ea, L18 2 ea).

17. Install the DOOR on the 2 screws of BRACKET DOOR.

18. Fasten the 3 screws that removed in step 3. Check position of screw that installed to bracket door.

19. Install the COVER HOLDER on the HOLDER GLASS and then

Fasten the 1 screws that removed in step 1.

L14

L12

L18

English - 21

DV9100HA DRY_DV56H_USER MANUAL_DC68-03170K-08_EN.indd 21 2016/2/25 16:36:58

operating instructions, tips

To reduce the risk of ﬁre, electric shock, or injury to persons, read the IMPORTANT SAFETY

WARNING

INSTRUCTIONS before operating this appliance.

OVERVIEW OF THE CONTROL PANEL

DV56H9100E

DV56H9100G

Cycle Selector

To select a cycle, rotate the Cycle Selector dial to the desired cycle. The indicator light by the cycle name will illuminate. The NORMAL, HEAVY

DUTY, BEDDING, SANITIZE, PERM PRESS, WOOL, DELICATES, ACTIVE WEAR, ECO NORMAL, and TOWELS cycles are Sensor Dry cycles.

Sensor Dry automatically senses the moisture in the load and shuts the dryer o when the load reaches the dryness level you have selected with the Dry Level Selection Button (see below).

ECO NORMAL - For reducing energy usage. This cycle adjusts cycle time and temperature for increased eciency.

NORMAL - The normal cycle is for most fabrics including cotton, linens, and normally soiled garments.

(If this cycle is selected, the Eco Dry function is enabled by default. For more information, please refer to the descriptions about the “Eco Dry” option.)

HEAVY DUTY - Use this cycle to get high heat for heavy fabrics such as jeans, corduroys, or work clothes.

BEDDING - For bulky items such as blankets, sheets and comforters. SANITIZE - Sanitizes garments by infusing high temperature heat deep into

the fabric during the drying cycle. Use this cycle to keep your bedding and curtains clean through sanitization. PERM PRESS - Dry wrinkle-free cottons, synthetic fabrics, knits, and

permanent press fabrics automatically.

English - 22

DV9100HA DRY_DV56H_USER MANUAL_DC68-03170K-08_EN.indd 22 2016/2/25 16:36:59

Digital Graphic

Display

WOOL - For machine washable and tumble dryable wool only. DELICATES - The DELICATES cycle is designed to dry heat-sensitive items at

a low drying temperature. ACTIVE WEAR - The ACTIVE WEAR cycle is for exercise wear and outdoor

wear such as sports jerseys, training pants, water-repellent jackets and other performance clothing. Thick fabrics like a zipper or velcro closure of a jacket,

or training socks may not be completely dried.

TOWELS - To dry bath towels and similar items. QUICK DRY - Provides a 30 minute drying cycle. TIME DRY - The TIME DRY cycle allows you to select a cycle time in minutes.

(If this cycle is selected, the Eco Dry function is enabled by default. For more information, please refer to the descriptions about the “Eco Dry” option.)

AIR FLUFF - The AIR FLUFF cycle tumbles the load in room temperature air. REFRESH - This cycle is best for smoothing out wrinkles and reducing odors

from loads consisting of one to four dry items. In this cycle a small amount of water is sprayed into the dryer drum after several minutes of tumbling with heat. Conﬁrm that the laundry load is dry.

WRINKLE AWAY - Removes wrinkles from clothes stored in closets, etc. It provides wrinkle release via optimized steam care. For best results, load 2-3 items at once. You can extend the drying time by a

minimum of 20 minutes , depending on the item type or load. Conﬁrm that the laundry load is dry.

The display window shows the estimated time remaining in the cycle after you have pressed the Start/Pause button. The estimated time remaining may ﬂuctuates as the cycle progresses.

The Drying light will illuminate and remain lit until the cycle is complete. When your dryer is in the cool-down phase, the Cooling light will illuminate. When

your dryer is in the wrinkle prevent phase, the Wrinkle Prevent light will illuminate. When the cycle is complete, “End” will appear in the display panel until you push

the Start/Pause button or the power button. If your dryer is paused during a cycle, the indicator lights will blink until you press the Start/Pause button.

02 operating instructions, tips

Dry Level

Selection Button

Temp. Selection

Button

Time Selection

Button

To select the dry level in the NORMAL, HEAVY DUTY, or other Sensor Dry cycles except SANITIZE, WOOL and ACTIVE WEAR press the Dry Level button. An indicator light will illuminate next to the desired dryness level.

Press the button repeatedly to scroll through the settings. Larger or bulkier loads may require the Very Dry or More Dry setting for complete dryness.

The Less Dry setting is best suited for lightweight fabrics or for leaving some moisture in the clothing at the end of the cycle. Damp Dry is designed to partially dry items. Use for items that lay ﬂat or hang to dry.

To select the temperature for the load, press the Temp. button. An indicator light will illuminate next to the temperature you selected. Press the button repeatedly to scroll through the settings.

High - For sturdy cottons or those labeled Tumble Dry. Medium - For permanent press, synthetics, lightweight cottons, or items

labeled Tumble Dry Medium. Med Low - For heat lower than Medium. Use to dry synthetic or washable knit

fabrics.

Low - For heat sensitive items labeled Tumble Dry Low or Tumble Dry Warm. Extra Low - Provides the lowest heated drying temperature possible.

When using Manual Dry cycles, you can adjust the drying time by pressing the time selection button.

During the Sensory Dry cycle, the time light indicator is o because exact drying times are determined by ﬂuctuating humidity levels.

Therefore, the actual drying time may dier from the displayed time.

English - 23

DV9100HA DRY_DV56H_USER MANUAL_DC68-03170K-08_EN.indd 23 2016/2/25 16:36:59

operating instructions, tips

Anti Static - To reduce statics by clothing friction and spray steam at the later period of drying cycle.

It is only available with: NORMAL, HEAVY DUTY, PERM PRESS, DELICATES (Dry level of every cycle exceeds Normal) and TIME DRY cycle.

Rack Dry - Rack Dry is available in the TIME DRY cycle. Temperature will be set to Extra Low only. (Refer to the “Rack Dry” section on page 25.)

Mixed Load Bell - The mixed load bell that notiﬁes you when the average dry level in a load is damp dry (80% dried). This lets you take garments that you don’t want fully dried or that dry quickly out of the dryer early while letting others continue to dry.

You can select this function in all Sensor Dry cycles except WOOL, SANITIZE and ACTIVE WEAR. The dry level selections are limited to Normal Dry, More

Dry, and Very Dry. Wrinkle Prevent - Wrinkle Prevent provides approximately 180 minutes

of intermittent tumbling in unheated air at the end of the cycle to reduce wrinkling. Press the Wrinkle Prevent button to activate this feature.

The indicator light above the pad will illuminate when Wrinkle Prevent is selected.

The load is dry, and can be removed at any time during the Wrinkle Prevent cycle.

Select Cycle

Option

Start/Pause

selection button

Power button

If you insert laundry into your dryer while it is extremely tangled immediately after your washer has ﬁnished a wash or spin cycle, it may degrade the drying eciency or cause the door to open. We recommend that you disentangle your laundry appropriately before inserting it.

Each indicator on the graphic display means:

My Cycle - Choose your favorite cycle including cycle, temp, dry level option, etc. (Refer to the “My cycle” section on page 26.)

Adjust Time - Time can be added or subtracted from the automatically set times in the Manual Dry cycles (TIME DRY, QUICK DRY, or AIR FLUFF cycles) and WRINKLE AWAY cycle.

To add or subtract time from the cycle, press the Adjust Time arrow pad up or down until the desired time is displayed.

Small Load Care

drying a small load in the Sensor Dry cycle. It is only available with: NORMAL, HEAVY DUTY, PERM PRESS and DELICATES

cycle. It can’t be selected/cancelled when the drying cycle is running. In order to improve drying eect and control operation rate, the drum can be

paused during operation. Eco Dry (Electric model Only) - This function is available in the NORMAL,

and TIME DRY cycles. When the Eco Dry function is activated, drying takes longer but the power consumption is reduced. (When the Eco Dry function is enabled, the drying time can be extended up to

3 times depending on the speciﬁed temperature and the amount of laundry to be dried. When the product is shipped, the Eco Dry function is set to On by default.)

Press to pause and restart programs.

Press once to turn your dryer on, Press again to turn it o. If you turn your dryer on and do not touch any buttons for 10 minutes, the power automatically turns o.

(Gas model Only) - To control the operation rate for

Steam

Child Lock

Filter Check

Vent Sensor

English - 24

DV9100HA DRY_DV56H_USER MANUAL_DC68-03170K-08_EN.indd 24 2016/2/25 16:37:00

RACK DRY

Door

Drying Rack

Using the drying rack

1. The drying rack is installed in the drum at in default state.

2. When using this dryer for the ﬁrst time, remove the drying rack from the drum. Pull upwards

vertically and take the drying rack out of the drum. Remove the package and keep it properly stored.

3. When you need to use drying rack, refer to the following steps for installation.

Installing the drying rack

1. Open the dryer door.

2. Place the Drying Rack inside the product, and then align the holes of the ﬁlter handle of the

Drying Rack to the front projections.

3. Place the rear legs in the two recessed areas of the dryer’s back wall, and then push down

the middle of the drying rack to ﬁx it in place.

4. Place the items to be dried on the rack, leaving space between them so air can circulate.

5. Close the dryer door.

6. Press the RACK DRY button in Time Dry cycle, and then select the time according to the

moisture and weight of item.

02 operating instructions, tips

Place the Drying Rack inside the dryer, align the holes of the ﬁlter handle of the Drying Rack with the front projections, and then secure the back of the Drying Rack.

SUGGESTED ITEMS SUGGESTED TEMP. SETTINGS

Washable sweaters

Extra Low (Time Dry cycle)

(block to shape and lay ﬂat on rack) Stued toys

Extra Low (Time Dry cycle)

(cotton or polyester ﬁberﬁlled) Stued toys

Air Flu

(foam or rubber-ﬁlled) Foam rubber pillows Air Flu Sneakers Air Flu

Don’t dry the drying rack together with the package when using the drying rack.

WARNING

Drying foam rubber, plastic, or rubber on a heat setting may cause damage to the items and create a ﬁre hazard.

In case this model is not supplied with a Drying Rack, you can purchase it through a service center.

English - 25

DV9100HA DRY_DV56H_USER MANUAL_DC68-03170K-08_EN.indd 25 2016/2/25 16:37:00

operating instructions, tips

MY CYCLE

Allows you to activate your custom dry (Cycle, Dry Level, Temp) with one button convenience. Press the My Cycle button to load and use the saved My Cycle options. The “My Cycle” light will indicate activation. Also, the chosen course and option lights will ﬂicker.

You can set options as follows in the My Cycle mode.

1. Press the Power button.

2. Select cycle using the Cycle Selector.

3. After cycle selection, set each option (Dry Level, Temp, Time)

4. You can then store the selected cycle and options by pressing and holding the My Cycle button for

longer than 3 seconds in My Cycle mode. The cycle and options you select will be displayed the next time you choose the My Cycle function.

You can change the My Cycle settings by repeating the same process above. The last used setting will be displayed the next time you choose the My Cycle function.

If you press My Cycle and release it within 3 seconds, the previously saved cycle and options appear. If you press and hold My Cycle for 3 second or longer, the currently set cycle and options are saved

and the LED blinks for 3 seconds.

DRUM LIGHT

Lights the dryer drum while the dryer is running.

Turning On and O

Press and hold the Wrinkle Prevent button for 3 seconds or more.

You can turn the Drum Light on and o while your dryer is running and when it is stopped. If you do not turn the Drum Light o 5 minutes after turning it on, the Drum Light

automatically turns o.

SOUND

The Sound O function can be selected during all cycles.

Activating

If you want to activate the Sound O function, press the Dry Level button at the same time for 3 seconds.

Deactivating

If you want to deactivate the Sound O function, press the Dry Level button at the same time for 3 seconds again.

When this function is selected, sound is turned o for all cycles. Even if the power is turned on and o repeatedly, the setting is retained.

CHILD LOCK

Prevents children from playing with your dryer.

Setting/Releasing

If you want to set or release the Child Lock, press the Temp. and Time buttons simultaneously for 3 seconds.

English - 26

DV9100HA DRY_DV56H_USER MANUAL_DC68-03170K-08_EN.indd 26 2016/2/25 16:37:00

Child Lock Details

- You can turn Child Lock on while your dryer is running.

- Once you turn Child Lock on, no button, except for the power button, will respond until you

turn o the Child Lock function.

- The Child Lock indicator will be lit.

If you have not turned o Child Lock, and then turned the dryer o and on, the Child Lock function will still be on. To turn o Child Lock, follow the instructions above.

When other buttons, except for the power button, do not respond, check the Child Lock indicator. If Child Lock is on, follow the instructions above to turn Child Lock o.

SMART CARE

This function enables you to check the status of the dryer using a smartphone.

1. To enable the Smart Care function, press the power button to turn the dryer on and then press and hold

the Time button for 3 seconds. If you press a button other than the Time button after turning the dryer on, you will not be able to activate the Smart Care function.

• The error code history is deleted after using the function.

2. If the Smart Care function is activated, the Smart Care indicator is lit on the display.

3. Run the Smart Care app on your smart phone.

• GalaxyS, GalaxyS2, GalaxyS3, GalaxyS4, GalaxyS2(HD), Galaxy Note, Galaxy Note2, Galaxy Note3

(Other devices may not be normal operation).

Supported operating system: Android 2.2 or higher.

• IPhone 3 G S, iPhone 4/4S, iPhone 5/5S.

Supported operating system : OS 4.3 or higher.

4. Focus the smart phone’s camera on the display panel of the dryer.

5. If the smart phone’s camera is focused on the display panel of the dryer, the panel and error message is

automatically recognized and the error type and countermeasures are displayed on the smart phone.

6. If the smartphone fails to recognize the error code more than twice, please enter the error code

displayed on the display panel of the dryer manually into the Smart Care app.

Downloading the Smart Care app

02 operating instructions, tips

• Download the Samsung Laundry App into your mobile phone from the Android market or Apple

App store. (Search word : Samsung Smart Washer/Dryer)

Precautions when using Smart Care

• If light from a light bulb, ﬂuorescent bulb, or lamp is reﬂected on the display panel of the dryer, the

smartphone may not be able to recognize the panel or error message easily.

• If you hold the smartphone at too large an angle relative to the front of the display panel, it may not

be able to recognize the error code. For best results, hold the smartphone so that the front of the panel and the smartphone are parallel or nearly parallel.

English - 27

DV9100HA DRY_DV56H_USER MANUAL_DC68-03170K-08_EN.indd 27 2016/2/25 16:37:00

operating instructions, tips

CLEAN THE LINT FILTER

• After or before each load.

• To shorten drying time.

• To operate more energy eciently.

Do not operate your dryer without the lint ﬁlter in place.

Frame Front

Filter

Door

LOAD THE DRYER PROPERLY

• Place only one washload in your dryer at a time.

• In mixed loads, heavy and lightweight fabrics will dry dierently. This may result in lightweight fabrics

being dry while heavy fabrics remain damp at the end of a drying cycle.

• Add one or more additional similar items to your dryer when you are drying only one or two items. This

improves the tumbling action and drying eciency.

• Overloading restricts tumbling action, resulting in uneven drying as well as excessive wrinkling of some

fabrics.

GETTING STARTED

1. Load your dryer loosely – DO NOT overload.

2. Close the door.

3. Select the appropriate cycle and options for the load ( See pages “Cycle Chart” ).

4. Press the Start/Pause button.

5. The dryer indicator light will illuminate.

6. The estimated cycle time will appear in the display.

The time may ﬂuctuate as humidity levels ﬂuctuate in the dryer.

• When the cycle is complete, “End” will appear in the display.

• Pressing power cancels the cycle and stops your dryer.

• The Drying, Cooling, and Wrinkle Prevent indicator lights will illuminate during those portions of the

cycle.

Do not place anything on top of your dryer while it is running.

WARNING

VENT SENSOR

Your Samsung dryer is equipped with a Vent Sensor, which detects and notiﬁes you when it is time to clean the ductwork. Keep your dryer safe and ecient by cleaning the ducts when prompted.

The Vent Sensor detects any duct blockages

You can ﬁ gure out whether there is a duct blockage from the “Vent Sensor ” lamp of the digital display.

English - 28

DV9100HA DRY_DV56H_USER MANUAL_DC68-03170K-08_EN.indd 28 2016/2/25 16:37:00

Level Message Status Solution

The “Vent Sensor

lamp is turned o.

The “Vent Sensor ”

lamp illuminates.

The ductwork is free from

”

blockages.

When a part of the duct or the lint ﬁlter is blocked by lint or a foreign object.

When the resistance is high because the duct is too long or bent.

Check the duct connection and shorten the duct and straighten it if necessary.

Check the lint ﬁlter or the duct and clean it if necessary.

Check the duct connection and shorten the duct and straighten it if necessary.

Check the lint ﬁlter or the duct and clean it as soon

The “Vent Sensor ”

lamp blinks.

When the duct is blocked by lint or a foreign object.

When the resistance is very high because the duct is too long or bent excessively.

as possible.

In the LEVEL 2 state, this lamp blinks for 3 hours after the completion of the cycle. (If the wrinkle

prevention function is activated, this message is displayed for up to 3 hours.) If the power button is pressed or the door is opened, the power is immediately turned o.

For more information about the duct installation, please refer to the “Ducting requirements” section on page 8.

02 operating instructions, tips

•Althoughthedryerisavailableeveniftheblockagemessageisdisplayed,thedryingtime

may be extended.

•IftheLEVEL1messageisdisplayedthersttimethedryerisrunaftertheinstallation,

check the connection and clean the duct. If the LEVEL 1 message appears even after you have checked and cleaned the ducts, this may indicate that there are some restrictions of the duct due to the length, condition, etc. If this occurs, you can use the dryer normally and no countermeasures need to be taken. However, the drying time may be extended or the drying performance may be degraded.

English - 29

DV9100HA DRY_DV56H_USER MANUAL_DC68-03170K-08_EN.indd 29 2016/2/25 16:37:00

care and cleaning

CONTROL PANEL

Clean with a soft, damp cloth. Do not use abrasive substances. Do not spray cleaners directly on the panel. The control panel ﬁnish may be damaged by some laundry pre-treatment soil and stain remover products. Apply such products away from your dryer and wipe up any spills or overspray immediately.

TUMBLER

Remove any stains from the tumbler caused by crayon, ink, fabric dye (from new items such as towels or jeans) and so on with an all-purpose cleaner.

Tumble old towels or rags to remove any remaining stain or cleaning substance. Once these steps are followed, stains may still be visible, but should not transfer to subsequent loads.

POWDER COATED TUMBLER

To clean the powder coated tumbler, use a damp cloth with a mild, non-abrasive cleaner suitable easily marred surfaces.

Remove cleaner residue and dry with a clean cloth.

DRYER EXTERIOR

Clean with a soft, damp cloth. Do not use abrasive substances. Protect the surface from sharp objects. Do not place any heavy or sharp objects or a detergent box on the dryer. They can scratch or damage the

top cover of the dryer. Keep these items in the separately purchased pedestal or in a separate storage box. The entire dryer has a high-gloss ﬁnish. Avoid scratching or damaging the surface when using the dryer.

DRYER EXHAUST SYSTEM

Inspect and clean the dryer exhaust system yearly to maintain optimum performance. The outside exhaust hood should be cleaned more frequently to ensure proper operation.

English - 30

DV9100HA DRY_DV56H_USER MANUAL_DC68-03170K-08_EN.indd 30 2016/2/25 16:37:00

+ 102 hidden pages