Samsung 941MG, 941MW User Manual

SyncMaster 941MW / 941MG

Install Driver

Notational

Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment.

Prohibited Important to read and understand at all times

Do not disassemble Disconnect the plug from the outlet

Power

Do not touch Ground to prevent an electric shock

When not used for extended period of time, set your computer to DPMS. If using a screen saver, set it to active screen mode.

The images here are for reference only, and are not applicable in all cases (or countries).

Do not use a damaged or loose plug.

! This may cause electric shock or fire.

Do not pull the plug out by the wire nor touch the plug with wet hands.

This may cause electric shock or fire.

Use only a properly grounded plug and receptacle.

An improper ground may cause electric shock or equipment damage.

(Class l Equipment only.)

Insert the power plug firmly so that it does not come loose.

A bad connection may cause fire.

Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage.

This may cause electric shock or fire.

Do not connect too many extension cords or plugs to one outlet.

This may cause fire.

Do not disconnect the power cord while using the monitor.

A surge may be caused by the separation and may damage the monitor.

Do not use the power cord when the connector or plug is dusty.

If the connector or plug of the power cord is dusty, clean it with a dry cloth.

Using the power cord with a dusty plug or connector may cause electric shock

or fire.

To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable.

This may cause electric shock or fire.

Installation

Be sure to contact an authorized Service Center, when installing your monitor in a location with heavy dust, high or low temperatures, high humidity, and exposed to chemical substances and where it operates for 24 hours such as at airports, train stations etc.

Failure to do so may cause serious damage to your monitor.

Place your monitor in a location with low humidity and a minimum of dust.

Failure to do so may cause electric shock or fire inside the monitor.

Do not drop the monitor when moving it.

This may cause damage to the product or the person carrying it.

Install the monitor base in a showcase or shelf so that the end of the base does not protrude from the showcase or shelf.

Dropping the product may cause damage to the product or the person carrying

it.

Do not place the product on the floor.

Take care, as someone, specifically children may trip over it.

Do not place the product on an unstable or small surface area.

Place the product on an even and stable surface, as the product may fall and

cause harm to someone walking by, specifically children.

TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OTHER OPEN FLAMES AWAY FROM THIS PRODUCT AT ALL TIMES.

Otherwise, this may cause fire.

Keep any heating devices away from the power cable.

A melted coating may cause electric shock or fire.

Do not install the product in places with poor ventilation, for instance, a bookshelf, closet, etc.

Any increase in the internal temperature may cause fire.

Put down the monitor carefully.

Failing to do so may damage the monitor.

Do not place the monitor face down.

This may damage the TFT-LCD surface.

The installation of the bracket must be done by a qualified professional.

Installing the bracket by unqualified personnel may result in injury.

Always use the mounting device specified in the owner's manual.

When installing the product, make sure to keep it away from the wall (more than 10 cm / 4 inches) for ventilation purposes.

Poor ventilation may cause an increase in the internal temperature of the

product, resulting in a shortened component life and degraded performance.

To prevent rainwater from running along the outdoor antenna cable and into the house, ensure that the outdoor portion of the cable is hanging below the point of entry.

If the product is exposed to rainwater, it may cause electric shock or fire.

When using an outdoor antenna, ensure that there is sufficient distance between the antenna and any electric wires nearby so that they do not come into with each other if the antenna is knocked over by strong wind or any other accident.

A knocked-over antenna may cause injury or electric shock.

Keep the plastic packaging (bag) out of children's reach.

The plastic packaging (bag) may cause suffocation if children play with it.

Clean

When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with a slightly moistened, soft fabric.

Do not spray water or detergent directly onto the monitor.

This may cause damage, electric shock or fire.

Use the recommended detergent with a smooth cloth.

If the connector between the plug and the pin is dusty or dirty, clean it properly using a dry cloth.

A dirty connector may cause electric shock or fire.

Make sure to unplug the power cord before cleaning the product.

Otherwise, this may cause electric shock or fire.

Unplug the power cord from the power outlet and wipe the product using a soft, dry cloth.

Do not use any chemicals such as wax, benzene, alcohol, thinners, insecticide,

air freshener, lubricant or detergent.

Contact the SAMSUNG customer care center or Customer Center for interior cleaning once a year.

! Keep the product's interior clean. Dust which has accumulated in the interior

over an extended period of time may cause a malfunction or fire.

Others

Do not remove the cover (or back).

! This may cause electric shock or fire. ! Refer to a qualified servicing company.

If your monitor does not operate normally - in particular, if there is any unusual sound or smell coming from the monitor - unplug it immediately and contact an authorized dealer or the Service Center.

! This may cause electric shock or fire.

Keep the product away from places exposed to oil, smoke or moisture; do not install inside a vehicle.

! This may cause a malfunction, electric shock or fire. ! In particular, avoid operating the monitor near water or outdoors where the

monitor could be exposed to snow or rain.

If the monitor is dropped or the casing is damaged, turn the monitor off and unplug the power cord. Then contact a Service Center .

The monitor may malfunction, causing electric shock or fire.

Disconnect the plug from the outlet during storms or lightning or if it is not used for a long period of time.

Failure to do so may cause electric shock or fire.

Do not try to move the monitor by pulling only the wire or the signal cable.

This may cause a breakdown, electric shock or fire due to damage to the

cable.

Do not move the monitor right or left by pulling only the wire or the signal cable.

This may cause a breakdown, electric shock or fire due to damage to the

cable.

Do not cover the vents on the monitor cabinet.

Bad ventilation may cause a breakdown or fire.

Do not place water containers, chemical products or small metal objects on the monitor.

This may cause a malfunction, electric shock or fire.

If a foreign substance enters the monitor, unplug the power cord and contact

the Service Center .

Keep the product away from combustible chemical sprays or inflammable substances.

This may cause an explosion or fire.

Never insert anything metallic into the monitor openings.

! This may cause electric shock, fire or injury.

Do not insert metal objects such as chopsticks, wire and tools or inflammable objects such as paper or matches into the vent, headphone port or AV ports or etc.

! This may cause electric shock or fire. If an alien substances or water enters the

product, turn the product off, unplug the power connector from the wall outlet and contact the Service Center.

When viewing a fixed screen for an extended period of time, residual image or blurriness may appear.

! Change the mode to energy saving mode or set a screensaver to a changing

picture when away from the monitor for an extended period of time.

Adjust the resolution and frequency to the level appropriate for the model.

An inappropriate resolution may cause undesirable picture quality.

19 inch Wide (48 cm) - 1440 X 900

Keep the volume at a comfortable level when using the headphones.

Excessively loud volume level may damage hearing.

Viewing the monitor continuously at a too close angle may result in damage to your eyesight.

To ease eye strain, take at least a five-minute break after every hour of using the monitor.

Do not install the product on an unstable, uneven surface or a location prone to vibrations.

Dropping the product may cause damage to the product or the person carrying

it. Using the product in a location prone to vibrations may shorten the lifetime of the product or may cause the product to catch fire.

When moving the monitor, turn off and unplug the power cord. Make sure that all cables, including the antenna cable and cables connected to other devices, are disconnected before moving the monitor.

Failure to disconnect cables may damage it and cause fire or electric shock.

Place the product out of children's reach, as they could damage by hanging onto it.

! A falling product may cause injury to the person or even fatality.

When not using the product for an extended period of time, keep the product unplugged.

Otherwise, this may cause heat emission from the accumulated dirt or

degraded insulation, causing electric shock or fire.

Do not place your children's favorite toys or any other objects of interest on the product.

! Children may try to climb on the product to retrieve an object. The product

could fall, causing injury or even fatality.

When removing batteries from the remote control, ensure that the children do not swallow the batteries. Keep the batteries out of children's reach.

! If the batteries are swallowed, see a doctor immediately.

When replacing batteries, place the batteries in the correct +/- polarity position as indicated on the battery holder.

The incorrect polarity may cause a battery to break or leak and may cause fire,

injury, or contamination (damage).

Use only specified standard batteries. Do not use new and used batteries together.

! This may cause a battery to break or leak and may cause fire, injury, or

contamination (damage).

The batteries (and rechargeable batteries) are not ordinary refuse and must be returned for recycling purposes. The customer is responsible for returning the used or rechargeable batteries for recycling purposes as the consumer.

The customer can return used or rechargeable batteries to a nearby public

recycling center or to a store selling the same type of the battery or rechargeable battery.

When lifting up or moving the monitor, do not lift the monitor upside down while holding only the stand.

This may cause your monitor to fall, and become damaged or cause personal

injury.

Good Postures When Using the Monitor

Try to maintain a good posture when using the monitor.

! Keep your back straight.

Keep a distance of about 45 ~ 50 cm between your eyes and the

monitor screen. Look at the screen from slightly above it, and have the monitor directly in front of you.

! Tilt the monitor upwards by 10 ~20 degrees. Adjust the monitor

height so that the top of the monitor is slightly below eye level. Adjust the monitor angle so that there is no reflected light on the

screen.Try to maintain your arms perpendicular to your armpits. Keep your arms level with the back of your hands.

Keep the angle of the elbow perpendicular.

! Keep the angle of the knees at more than 90 degree. Do not let

your feet fall up from the floor. Adjust the arm position so that it is below the heart.

Unpacking

Please make sure the following items are included with your monitor.

If any items are missing, contact your dealer.

Contact a local dealer to buy optional items.

Without Stand With Stand

Manual

Quick Setup Guide

Cable

Warranty Card

(Not available in all locations)

User's Guide, Monitor Driver

D-Sub Cable Audio Cable Power Cord

Other

Sold separately

Remote Control Batteries (AAA X 2)

Component(P

, PB, Y) Cable

TV Antenna Cable

(Coaxial Cable)

RCA Cable (Video-Yellow,

Audio-Red and White)

S-VIDEO Cable Earphones/Headphones SCART Cable

Front

DVI Cable

1. SOURCE

2. PIP

3. MENU

7. [ ] Power button

8. Remote control sensor

9. Power indicator

10. Speaker

1. SOURCE

Press the SOURCE button to change the input signal source. Changing the source is allowed only in external devices that are connected to the monitor at the time. To switch Screen modes: [PC] → [DVI] → [TV] → [Ext.] → [AV] → [S-Video] → [Component]

>>Click here to see an animation clip

2. PIP - Available in PC/DVI Mode In PC mode, turns on Video or TV screens in PIP mode.

3. MENU Use this button for open the on-screen menu and exits from the menu screen or closes screen adjustment menu.

8. Remote Control Sensor

9. Power indicator

10. Speaker

See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed or when leaving it unattended for long periods.

Moves from one menu item to another vertically or adjusts selected menu values. In TV mode, selects TV channels.

Moves from one menu item to another horizontally or adjusts selected menu values. Adjusts the audio volume.

Activates a highlighted menu item.

[ ] Power button

Use this button to turn the monitor On/Off.

Aim the remote control towards this spot on the Monitor.

Power Indicator shows power saver mode by green blinking. For more information, see the

PowerSaver section.

You can hear sound by connecting the soundcard of your PC to the monitor.

Rear

(The configuration at the back of the monitor may vary from product to product.)

1. POWER

2. DVI/PC IN

! Power terminal

Connect the power cord for your monitor to the POWER on the back of the monitor. This product may be used with 100 ~ 240VAC(+/10%).

1. DVI(HDCP) : Connect the DVI cable to the DVI(HDCP) port on the back of your monitor.

2. RGB : Connect the signal cable to the RGB port on the back of your monitor.

3. AUDIO : PC sound terminal (input).

3. EXT(RGB)

! Connect the EXT (RGB) port of the monitor to the

DVD Player using a SCART jack.

s for EXT(RGB) port of the monitor, it makes TV or

Video signal input and output.

4. COMPONENT IN

1. R - AUDIO - L : Connect the port of the DVD, VCR (DVD / DTV Set-Top Box) to the R-AUDIO-L port of the monitor.

2. P

, PB,Y

: Connect the VIDEO OUT port of the DVD / DTV Set-Top Box to the P component video cable (P

, PB,Y input ports using a

, PB,Y).

5. ANT IN

7. / S-VIDEO / VIDEO / L - AUDIO - R

Connect the CATV cable or TV antenna cable to the

"ANT IN" port on the rear side of the monitor. Make sure to use a TV antenna cable (sold separately) as the antenna cable.

The Kensington lock is a device used to physically

fix the system when using it in a public place. (The locking device has to be purchased separately.)

For using a locking device, contact where you purchase it.

1. Connect your headphones to the Headphone connection terminal.

2. S-VIDEO / VIDEO : Input devices such as DVD, VCR or Camcorder are connected to the VIDEO or S-VIDEO terminal of the monitor using the Video or S-Video cable.

3. L - AUDIO - R : Connect the port of the DVD, VCR (DVD / DTV Set-Top Box) to the L - AUDIO - R port of the monitor.

See Connecting the monitor for further information regarding cable connections.

Remote Control

The performance of the remote control may be affected by a TV or other electronic device operated near

the monitor, causing malfunction due to interference with frequency.

1. POWER

2. Number button

3. -/--, +100

MUTE

10. SOURCE

11. INFO

12.

13. Up-Down Left-Right buttons

14. AUTO

15. P.MODE, M/B (MagicBright™)

16. P.SIZE

17. STILL

18. PIP

19.

20.

21.

22. SOURCE

23. SIZE

24.

25. MAGIC-CH

1. POWER

Turns the monitor On/Off.

2. Number button

Selects TV channels in the TV mode. Used to change channels when PIP is selected and the PIP Source is set to TV.

3. -/-- (One/Two-Digit channel selection )

Use to select a channel numbered ten or over. Press this button, and the "--" symbol is displayed. Enter the two-digit channel number. This function is available only in Europe.

+100 (Not availble)

Press to select channels over 100. For example, to select channel 121, press "+100", then press "2" and "1".

5. MUTE

6. TTX/MIX

7. MENU

8. ENTER

Adjusts the audio volume.

Press to mute the sound temporarily. Displayed on the bottom left of the screen. Press the MUTE button again to cancel the Mute function. Alternatively press the buttons to cancel the Mute function.

TV channels provide written information services via teletext. For more information > TTX / MIX This function is available only in Europe.

Opens the on-screen menu and exits from the menu or closes the adjustment menu.

Activates a highlighted menu item.

TTX/MIX

ENTER

EXIT

S.MODE DUAL/MTS

PRE-CH

POSITION

In TV mode, selects TV channels.

10. SOURCE Press the 'SOURCE' button to change the input signal source. Changing the source is only allowed for external devices that are connected to the monitor at the time.

11. INFO Current picture information is displayed on the upper left corner of the screen.

12. EXIT Exits from the menu screen.

13. Up-Down Left-Right buttons

Moves from one menu item to another horizontally, vertically or adjusts selected menu values.

14. AUTO - Available In PC mode Only

Adjusts the screen display automatically.

15. P.MODE, M/B (MagicBright™)

Press to select a pre-defined Picture Mode of the monitor or to change the picture atmosphere as required. When you press this button, current mode is displayed on the lower center of the screen.

TV / Ext. / AV / S-Video / Component : P.MODE The monitor has four automatic picture settings that are preset at the factory. Then press the button again to circle through available preconfigured modes. ( Dynamic → Standard → Movie → Custom )

PC / DVI Mode : M/B ( MagicBright™ ) MagicBright™ is a new feature providing the optimum viewing environment depending on the contents of the image you are watching. Then press the button again to circle through available preconfigured modes. ( Entertain→ Internet → Text → Custom )

16. P.SIZE

Press to change the screen size.

- PC/ DVI mode : Wide / 4:3

- TV / Ext. / AV / S-Video mode : Auto Wide / Wide / 16:9 / Zoom1 / Zoom2 / 4:3

- Component mode : Wide / 16:9 / Zoom1 / Zoom2 / 4:3

17. STILL - Operates only for the CVBS, S-Video and RF Signal sources. Press the button once to freeze the screen. Press it again to unfreeze.

18. PIP - Available in PC/DVI Mode Push the PIP button to turn PIP screen On/Off.

19. S.MODE ( Sound Mode )

When you press this button, current mode is displayed on the lower center of the screen. The monitor has a built-in high fidelity stereo amplifier. Then press the button again to circle through available preconfigured modes. ( Standard → Music → Movie → Speech → Custom )

20. DUAL / MTS DUAL : STEREO/MONO, DUAL l / DUAL ll and MONO/NICAM MONO/NICAM STEREO

can be operated depending on broadcasting type by using DUAL button on the remote control while watching TV.

MTS : You can select the MTS (Multichannel Television Stereo) mode. . Mono, Stereo, SAP (Separate Audio Program) Set 'MTS' to ON to choose Mono, Stereo or SAP.

21. PRE-CH This button is used to return to the immediately previous channel.

22. SOURCE - Adjustable when the PIP function is ON.

Selects the Video source.

23. SIZE - Adjustable when the PIP function is ON.

You can switch the PIP picture size.

24. POSITION - Adjustable when the PIP function is ON.

Changes the Position of the PIP window.

+ 39 hidden pages