Samsung 400UXn, 460UXn User Manual

SyncMaster 400UXn,460UXn

LCD Monitor

User Manual

Safety Instructions

Notational

Note

These safety instructions must be followed to ensure your safety and prevent property damage.

Make sure to read the instructions carefully and use the product in the correct manner.

Warning / Caution

Failure to follow directions noted by this symbol could result in bodily harm
or damage to the equipment.

Notational Conventions

Power

Prohibited

Do not disassemble

Do not touch

When not used for extended period of time, set your computer to DPM.

If using screen saver, set it to active screen mode.

The images here are for reference only, and are not applicable in all cases (or
countries).

Shortcut to Anti-Afterimage Instructions

Do not use a damaged power cord or plug or a damaged or loose power

outlet.

• Otherwise, this may result in electric shock or fire.

Important to read and under­stand at all times

Disconnect the plug from the
outlet

Ground to prevent an electric
shock

Do not touch the power plug with wet hands when removing or plug-

ging the plug into the outlet.

• Otherwise, this may result in electric shock.

Make sure to connect the power cord to a grounded power outlet.

• Otherwise, it may result in electric shock or personal injury.

Ensure that the power plug is plugged into the power outlet firmly and

correctly.

• Otherwise, this may result in fire.

Safety Instructions

Do not forcefully bend or pull the power plug and do not place any

heavy material on it.

• Otherwise, this may result in fire.

Do not connect multiple appliances to the same power outlet.

• Otherwise, this may cause fire due to overheating.

Do not disconnect the power cord while using the product.

• Otherwise, this may result in damage to the product due to electric
shock.

To disconnect the apparatus from the mains, the plug must be pulled
out from the mains socket, therefore the mains plug shall be readily op­erable.

• This may cause electric shock or fire.

Use only the power cord provided by our company. Do not use the
provided power cord of another product.

Installation

• Otherwise, this may result in fire or electric shock.

Be sure to contact an authorized Service Center when installing your monitor in
a location with heavy dust, high or low temperatures, high humidity, and exposed
to chemical substances and where it operates for 24 hours such as at airports,
train stations etc.

Failure to do so may cause serious damage to your monitor.

Ensure that at least two persons lift and move the product.

• Otherwise, it may be dropped and cause personal injury, and/or dam-

age the product.

When installing the product in a cabinet or rack, make sure that the
front end of the bottom of the product does not project out.

• Otherwise, it may fall or cause personal injury.

• Use a cabinet or rack of a size appropriate to the product.

DO NOT PLACE CANDLES, MOSQUITO REPELLANT, CIGA­RETTES AND ANY HEATING APPLIANCES NEAR THE PROD­UCT.

• Otherwise, this may result in fire.

Keep heating appliances as far away from the power cord or the prod­uct as possible.

• Otherwise, this may result in electric shock or fire.

Safety Instructions

Do not install it in a badly ventilated location such as a bookcase or
closet.

• Otherwise, this may result in fire due to an increase in the internal

temperature.

When putting the product down, make sure to put it down softly.

• Otherwise, this may result in damage to the screen display.

Do not place the front of the product on the floor.

• Otherwise, this may result in damage to the screen display.

Ensure that an authorized installation company installs the wall mount.

• Otherwise, it may fall and cause personal injury.

• Make sure to install the specified wall mount.

Install your product in a well ventilated location. Ensure that there is
a clearance of more than 10 cm from the wall.

Clean

• Otherwise, it may result in fire due to an increase in the internal tem-

perature.

Ensure that the packaging vinyl is kept away from children.

• Otherwise, it may result in serious harm (suffocation) if children play

with it.

If the height of your monitor is adjustable, do not place any object or
part of your body on the stand when lowering it.

• This may cause damage to the product or the person carrying it.

When cleaning the monitor case or the surface of the TFT-LCD screen, wipe
with a slightly moistened, soft fabric.

Do not spray cleaner directly onto the surface of the product.

• Otherwise, this may result in the discoloration and distortion of the

structure and the screen surface may peel off.

Clean the product using a soft cloth with a monitor cleaner only. If
you must use a cleaner other than the monitor cleaner, dilute it with water
at a ratio of 1:10.

When cleaning the power plug pins or dusting the power outlet, clean
it with a dry cloth.

• Otherwise, it may result in fire.

Safety Instructions

When cleaning the product, make sure to disconnect the power cord.

• Otherwise, it may result in electric shock or fire.

When cleaning the product, disconnect the power cord and clean it
softly with a dry cloth.

• (Do not use chemicals such as wax, benzene, alcohol, thinner, mos-

quito repellant, lubricant, or cleaner.) These may change the appear­ance of the product surface and peel off the indication labels on the
product.

Since the product housing is easily scratched, make sure to use the
specified cloth only.

• Use the specified cloth adding only a little water. As the product may

be scratched if there is any foreign material on the cloth, make sure
to shake it thoroughly before using it.

When cleaning the product, do not spray water directly onto the main
body of the product.

Others

• Ensure that water does not enter the product and that it is not wet.

• Otherwise, this may result in electric shock, fire or a malfunction.

The product is a high voltage product. Ensure that users do not disas­semble, repair or modify the product themselves.

• Otherwise, this may result in electric shock or fire. If the product

needs to be repaired, contact a Service Center.

If there is a strange smell or a strange sound or smoke is coming from
the product, disconnect the power plug immediately and contact a Service
Center.

• Otherwise, this may result in electric shock or fire.

Do not place this product in a location exposed to moisture, dust,
smoke, water, or in a car.

• Otherwise, this may result in electric shock or fire.

When you drop the product or the case is broken, turn the power off
and disconnect the power cord. Contact a Service Center.

• Otherwise, this may result in electric shock or fire.

If thunder or lightening is occurring, do not touch the power cord or
antenna cable.

• Otherwise, this may result in electric shock or fire.

Safety Instructions

Do not try to move the monitor by pulling only the wire or the signal
cable.

• Otherwise, it may fall and result in electric shock, damage to the

product or fire due to damage to the cable.

Do not lift or move the product back and forwards or right and left
while only holding the power cord or signal cables.

• Otherwise, it may fall and result in electric shock, damage to the

product or fire due to damage to the cable.

Make sure that the ventilating opening is not blocked by a table or
curtain.

• Otherwise, it may result in fire due to an increase in the internal tem-

perature.

Do not place any containers containing water, vases, flowerpots, med­icines as well as any metal on the product.

• If water or a foreign material enters the product, disconnect the power

cord and contact a Service Center.

• This may result in a product malfunction, electric shock, or fire.

Do not use or keep combustible spray or flammable material near the
product.

• Otherwise, this may result in an explosion or fire.

Do not insert any metal, such as chopsticks, coins, pins and steels, or
inflammable objects, such as matches or paper, inside the product
(through the ventilating openings, input and output terminals, etc).

• If water or foreign material enters the product, disconnect the power

cord and contact a Service Center.

• Otherwise, this may result in electric shock or fire.

When using a fixed screen for a long time, an afterimage or stain may
occur.

• If you are not using your product for a long period of time, put it into

sleep mode or use a moving screen saver.

Set a resolution and frequency appropriate to the product.

• Otherwise, your eyesight may be damaged.

When using headphones or earphones, do not turn the volume too high.

• Having the sound too loud may damage your hearing.

If you continually move closer to the product screen, your eyesight
may be failing.

Safety Instructions

Take a rest for at least five (5) minutes after using the monitor for one
(1) hour.

This reduces the weariness of your eyes.

Do not install it in an unstable location such as an unstable rack or
uneven surface or a location exposed to vibrations.

• Otherwise, it may fall and cause personal injury and/or damage the

product.

• If you use the product in a location exposed to vibrations, it may

damage the product and result in fire.

When moving the product, turn the power off and disconnect the power
plug, antenna cable, and all the cables connected to the product.

• Otherwise, it may result in electric shock or fire.

Ensure that children do not hang onto the product or climb up onto the
product.

• The product may fall and cause personal injury or death.

If you do not use the product for a long period of time, disconnect the
power cord from the power outlet.

• Otherwise, this may result in overheating or fire due to dust, and may

result in fire due to electric shock or leakage.

Do not place any heavy items or toys or confectionery, such as cookies
etc. that may attract the attentions of children onto the product.

• Your children may hang onto the product causing it to fall and this

may result in personal injury or death.

Be careful that children do not place the battery in their mouths when
removed from the remote control. Place the battery in a location that
children or infants cannot reach.

• If children have had the battery in their mouths, consult your doctor

immediately.

When replacing the battery, insert it with right polarity (+, -).

• Otherwise, the battery may become damaged or it may cause fire,

personal injury or damage due to leakage of the internal liquid.

Use only the specified standardized batteries, and do not use a new
battery and a used battery at the same time.

• Otherwise, the batteries may be damaged or cause fire, personal in-

jury or damage due to a leakage of the internal liquid.

The batteries (and rechargeable batteries) is not ordinary refuse and
must be returned for recycling purposes. The customer is responsible for
returning the used or rechargeable batteries for recycling purposes as the
consumer.

• The customer can return used or rechargeable batteries to a nearby

public recycling center or to a store selling the same type of the battery
or rechargeable battery.

Safety Instructions

Do not place the product in a location exposed to direct sunlight or
near any heat such as a fire or heater.

• This may reduce the lifetime of the product, and may result in fire.

Do not drop any objects onto the product or cause any impact to the
product.

• Otherwise, this may result in electric shock or fire.

Do not use a humidifier or kitchen table near the product.

• Otherwise, this may result in electric shock or fire.

When there is a gas leak, do not touch the product or the power plug
but ventilate immediately.

• If a spark occurs, it may cause an explosion or fire.

If the product has been turned on for a long time, the display panel
becomes hot. Do not touch it.

• Keep the small accessories in a location out of the reach of children.

Be careful when adjusting the angle of the product or the height of the
stand.

• This may result in personal injury as your hand or fingers may be-

come caught.

• Also, if you tilt the product too far, it may fall and cause personal

injury.

Do not install the product in a location low enough for children to
reach.

• Otherwise, it may fall and result in personal injury.

• Since the front part of the product is heavy, install the product on a

level and stable surface.

Do not put any heavy objects on the product.

• This may result in personal injury and/or damage to the product.

Introduction

-- 400UXn --

Package Contents

Note

Please make sure the following items are included with your LCD Display.

If any items are missing, contact your dealer.

Contact a local dealer to buy optional items.

Note

This stand is not for the Floor Standing Type.

Unpacking

Manuals

Quick Setup Guide Warranty Card

(Not available in all loca-

Cables

D-Sub Cable Power Cord

LCD Display

User's Guide

tions)

Others

Introduction

Sold separately

-- 400UXn --

Remote Control Batteries (AAA X 2)

(Not available in all loca-

tions)

DVI Cable Wall Mount KIT Semi Stand KIT

BNC Cable LAN Cable For more information on the

BNC to RCA Adaptor Jack

Calibrater

use of the calibrater, see Nat-

ural Color Expert Help.

Your LCD Display

Front

MENU button [MENU]

Introduction

Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu
or return to the previous menu.

Navigate buttons (Up-Down buttons)

Moves from one menu item to another vertically or adjusts selected menu values.

Adjust buttons (Left-Right buttons) / Volume buttons

Moves from one menu item to another horizontally or adjusts selected menu val­ues. When OSD is not on the screen, push the button to adjust volume.

ENTER button [ENTER]

Activates a highlighted menu item.

SOURCE button [SOURCE]

Switches from PC mode to Video mode. Changing the source is only allowed for
external devices that are connected to the LCD Display at the time.

[PC] → [BNC] → [DVI] → [AV] → [S-Video] → [Component] → [HDMI]
→ [MagicInfo]

>> Click here to see an animation clip

PIP

Push the PIP button to turn the PIP screen On / Off.

More than one PIP cannot overlap on screen as BNC and the component use the
same terminal.

>> Click here to see an animation clip

• PC

AV / S-Video / Component / HDMI Mode

• BNC

AV / S-Video / HDMI Mode

• DVI

AV / S-Video / Component Mode

• AV / S-Video

PC / BNC / DVI Mode

• Component

PC / DVI Mode

• HDMI

PC / BNC Mode

Power button [ ]

Use this button for turning the LCD Display on and off.

Power indicator

Shows PowerSaver mode by blinking green

Rear

Introduction

Note

See PowerSaver described in the manual for further information regarding power
saving functions. For energy conservation, turn your LCD Display OFF when it
is not needed or when leaving it unattended for long periods.

Remote Control Sensor

Aim the remote control towards this spot on the LCD Display.

Note

For detailed information concerning cable connections, refer to Connecting Cables under Setup. The
LCD Display 's configuration at the back may vary slightly depending on the LCD Display model.

POWER S/W ON [ │ ] / OFF [O]

Switches the LCD Display On/Off.

POWER IN

The power cord plugs into the LCD Display and
the wall plug.

Introduction

REMOTE OUT/IN

You can use a wired remote control by connecting
it to your LCD Display.

RS232C OUT/IN (RS232C Serial PORT)

MDC(Multiple Display Control) Program Port

DVI / PC / HDMI IN [PC/DVI/BNC AUDIO
IN] (PC/DVI/BNC/HDMI Audio Connection Ter­minal (Input))

DVI / PC / HDMI IN [HDMI]

Connect the HDMI terminal at the back of your
LCD Display to the HDMI terminal of your dig­ital output device using a HDMI cable.

DVI / PC / HDMI IN [RGB](PC Video Con­nection Terminal)

Using a D-Sub Cable (15 pin D-Sub) - PC mode
(Analog PC)

DVI / PC / HDMI IN [DVI(HDCP)] (PC

Video Connection Terminal)

Using a DVI Cable (DVI-D to DVI-D) - DVI
mode (Digital PC)

COMPONENT AUDIO IN [L-AUDIO-R]
(Component Audio Connection Terminal (Input))

BNC/COMPONENT OUT [R/PR, G/Y, B/
PB, H, V] (BNC/Component Connection Termi­nal (Output))

BNC (Analog PC) Connection: connecting the R,
G, B, H, V ports

Component Connection: connecting the PR, Y,
PB ports

BNC/COMPONENT IN [R/PR, G/Y, B/PB,
H, V](BNC/Component Connection Terminal
(Input))

Introduction

AV AUDIO IN [L-AUDIO-R] (LCD Display
Audio Connection Terminal (Input))

AV OUT [VIDEO](VIDEO Connection Ter­minal)

AV mode (Output)

AV IN [VIDEO](VIDEO Connection Termi­nal) (Input)

AV OUT [S-VIDEO] (S-VIDEO Connection
Terminal)

S-VIDEO mode (Output)

AV IN [S-VIDEO](S-VIDEO Connection
Terminal) (Input)

EXT SPEAKER(8 Ω)[- - L - +, - - R - +] (EXT
Speaker Connection Terminal)

AUDIO OUT [L-AUDIO-R] (LCD Display
Audio Connection Terminal (Output))AUDIO
OUT is the terminal for sound output of PC, DVI
or BNC.

LAN (LAN Connection Terminal)

USB(USB Connection Terminal)

Keyboard / Mouse, Mass Storage Device Com­patible.

Note

The number of LCD Displays that can be con­nected to loopout may differ depending on the
cables, signal source etc. With cables where there
is no degradation or signal source, up to ten LCD
Displays can be connected.

Note

See Connecting Cables for further information regarding cable connections.

-- 400UXn --

Remote Control

Note

The performance of the remote control may be affected by a TV or other electronic device operating
near the LCD Display , causing a malfunction due to interference with the frequency.

Introduction

ON / OFF

MagicInfo

MDC

LOCK

MagicInfo buttons

+100 DEL

VOL

MUTE

TTX/MIX

MENU

ENTER

P.MODE

AUTO

ENTER/PRE-CH

CH/P

SOURCE

INFO

EXIT

Up-Down Left-Right buttons

S.MODE

STILL

FM RADIO

P.SIZE

SRS

DUAL/MTS

PIP

SOURCE

SWAP

SIZE

REW

Introduction

STOP

PLAY/PAUSE

FF

1. ON / OFF Turns the LCD Display On/Off.

2. MagicInfo MagicInfo Quick Launch Button.

3. MDC MDC Quick Launch Button.

4. LOCK Activates or deactivates all function keys on both the remote con­trol and the LCD Display except for the Power and LOCK buttons.

5. MagicInfo buttons MagicInfo Quick Launch Button.

• Alphanumeric: Used to enter the Internet address.

• DEL: Functions as the backspace.

• SYMBOL: Used to enter the symbols. (.O_-)

• ENTER: Used to enter values.

6. +100 DEL

7. VOL Adjusts the audio volume.

8. MUTE

9. TTX/MIX

10.

11. ENTER

12.

MENU

P.MODE

Press to select channels over 100. For example, to select channel
121, press "+100", then press "2" and "1".

- This fuction does not work for this LCD Display.

Pauses (mutes) the audio output temporarily. This is displayed on
the lower left corner of the screen. The audio resumes if MUTE
or - VOL + is pressed in the Mute mode.

TV channels provide text information services via teletext.

- This fuction does not work for this LCD Display.

Opens the on-screen menu and exits from the menu screen or
closes the screen adjustment menu.

Activates a highlighted menu item.

When you press this button, current picture mode is displayed on
the lower center of the screen.

AV / S-Video / Component : P.MODE

The LCD Display has four automatic picture settings that are pre­set at the factory. Then push button again to circle through avail­able preconfigured modes. ( Dynamic → Standard → Movie
→ Custom )

PC / DVI / BNC : M/B (MagicBright)

MagicBright is a new feature providing the optimum viewing
environment depending on the contents of the image you are

Introduction

watching. Then push button again to circle through available pre­configured modes. (Entertain → Internet → Text → Custom )

13. AUTO Adjusts the screen display automatically in PC mode. By changing
the resolution in the control panel, auto function is performed.

14. ENTER/PRE-CH

15. CH/P In TV mode, selects TV channels.

16. SOURCE

17.

18. EXIT

19. Up-Down Left-Right but-

tons

20.

21. STILL Press the button once to freeze the screen. Press it again to un-

INFO

S.MODE

Returns to the immediately previous channel.

- This fuction does not work for this LCD Display.

- This fuction does not work for this LCD Display.

Changes the video source.

The current picture information is displayed in the top left corner
of the screen.

Exits from the menu screen.

Moves from one menu item to another horizontally, vertically or
adjusts selected menu values.

When pressing this button, the current mode is displayed at the
bottom centre of the screen. The LCD Display has a built-in high
fidelity stereo amplifier. Then press the button again to circle
through available preconfigured modes. ( Standard → Music
→ Movie → Speech → Custom )

freeze.

22. FM RADIO Turns the FM Radio on/off. In PC/DVI mode, sets the SOUND
to FM Radio. In general Video mode, selects FM Radio, and turns
off the screen. In areas where the signal is weak, noise may occur
during FM radio broadcasts.

- This fuction does not work for this LCD Display.

23. P.SIZE Press to change the screen size.

24. SRS

25. DUAL/MTS

SRS

DUAL-

STEREO/MONO, DUAL l / DUAL ll and MONO/NICAM
MONO/NICAM STEREO can be operated depending on the
broadcasting type by using the DUAL button on the remote control
while watching TV.

MTS-

You can select MTS (Multichannel Television Stereo) mode.

Audio Type MTS/S_Mode Default

FM Stereo Mono Mono Manual Change

Stereo Mono ↔ Stereo

SAP Mono ↔ SAP Mono

Introduction

- This fuction does not work for this LCD Display.

26. PIP

27.

28. SWAP Swaps the contents of the PIP and main image. The image in the

29.

30.

31.

32. PLAY / PAUSE

33.

SOURCE

SIZE

REW

STOP

FF

-- 400UXn --

Mechanical Layout

Mechanical Layout

Every time you press the button, a PIP screen appears.

Changes the source of the PIP window signal.

PIP window will appear on the main screen, and the main screen
image will appear in the PIP window.

Switches the PIP Picture Size.

Rewind

Stop

Play/Pause

Fast forward

NETWORK MODEL SIZE

LCD Display Head

NETWORK MODEL SIZE

Introduction

Installation VESA Bracket

• When installing VESA, make sure to comply with the international VESA standards.

• Purchasing VESA Bracket and Installation Information : Please contact your nearest SAMSUNG

Distributor to place an order. After your order is placed, installation professionals will visit you
and install the bracket.

• At least 2 persons are needed in order to move the LCD Display.

• SAMSUNG is not responsible for any product damage or any injury caused by installation at

customer's discretion.

Dimensions

Introduction

Notice

For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12 mm length.

Wall Bracket Installation

• Contact a technician for installing the wall bracket.

• SAMSUNG Electronics is not responsible for any damages to the product or harm to customers

when the installation is done by the customer.

• This product is for installing on cement walls. The product may not stay in place when installed

on plaster or wood.

Components

Only use the components and accessories shipped with the product.

Wall Bracket(1) Hinge(Left 1, Right1)Plastic

Wall Bracket Assembly

Note

There are two hinges(left and right). Use the correct one.

1. Insert and tighten the Captive Screw in the direction of the arrow.

When done, mount the wall bracket on the wall.

Hanger
(4)

Screw
(A)(11)

Screw(B)
(4)

Anchor
(11)

Introduction

There are two hinges(left and right). Use the correct one.

A - Captive Screw

B - Wall Bracket

C - Hinge (Left)

D - Hinge (Right)

2. Before drilling into the wall, check if the length between the two locking holes at the back of the

product is correct.

If the length is too short or long, loosen all or some of the 4screws on the wall bracket to adjust
the length.

A - Length between the two locking holes

3. Check the installation diagram and mark the drill points on the wall. Use the 5.0 mm bit to drill

holes deeper than 35 mm. Fix each anchor in the corresponding hole. Match each of the brackets
and hinge holes to the corresponding anchor holes and insert and tighten the 11 screws A.

Introduction

To mount the product on the wall bracket

The shape of the product may vary depending on the model. (The assemblies of the plastic hanger and
the screw are the same)

1. Remove the 4 screws on the back of the product.

2. Insert the screw B into the plastic hanger.

Notice

• Mount the product on the wall bracket and make sure it is properly fixed to the left and right
plastic hangers.

• Be careful when installing the product on the bracket as fingers can be caught in the holes.

• Make sure the wall bracket is securely fixed to the wall, or the product may not stay in place
after installation.

3. Tighten the 4 screws in step 2 (plastic hanger + screw B)to the rear holes of the product.

Introduction

4. Remove safety pin (3) and insert the 4 product holders into the corresponding bracket holes (1).
Then place the product(2) so that it is firmly fixed to the bracket. Make sure to re-insert and tighten
the safety pin (3) to securely hold the product to the bracket.

A - LCD Display

B - Wall Bracket

C - Wall

Wall Bracket Angle Adjustment

Adjust the bracket angle to -2° before installing it on the wall.

1. Fix the product to the wall bracket.

2. Hold the product at the top in the center and pull it forward (direction of the arrow) to adjust the
angle.

3. You can adjust the bracket angle between -2° and 15°.

Make sure to use the top center, and not the leftor the right side of the product to adjust the angle.

-- 460DXn --

Package Contents

Note

Please make sure the following items are included with your LCD Display.

Introduction

If any items are missing, contact your dealer.

Contact a local dealer to buy optional items.

This stand is not for the Floor Standing Type.

Unpacking

Manuals

Note

LCD Display

Quick Setup Guide Warranty Card

(Not available in all loca-

tions)

User's Guide

Cables

Others

Introduction

D-Sub Cable Power Cord

Remote Control Batteries (AAA X 2)

(Not available in all loca-

Sold separately

DVI Cable Wall Mount KIT Semi Stand KIT

BNC Cable LAN Cable For more information on the

BNC to RCA Adaptor Jack

tions)

Calibrater

use of the calibrater, see Nat-

ural Color Expert Help.

-- 460DXn --

Your LCD Display

Front

Introduction

MENU button [MENU]

Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu
or return to the previous menu.

Navigate buttons (Up-Down buttons)

Moves from one menu item to another vertically or adjusts selected menu values.

Adjust buttons (Left-Right buttons) / Volume buttons

Moves from one menu item to another horizontally or adjusts selected menu val­ues. When OSD is not on the screen, push the button to adjust volume.

ENTER button [ENTER]

Activates a highlighted menu item.

SOURCE button [SOURCE]

Switches from PC mode to Video mode. Changing the source is only allowed for
external devices that are connected to the LCD Display at the time.

[PC] → [BNC] → [DVI] → [AV] → [S-Video] → [Component] → [HDMI]
→ [MagicInfo]

>> Click here to see an animation clip

PIP

Push the PIP button to turn the PIP screen On / Off.

More than one PIP cannot overlap on screen as BNC and the component use the
same terminal.

>> Click here to see an animation clip

• PC

Introduction

AV / S-Video / Component / HDMI Mode

• BNC

AV / S-Video / HDMI Mode

• DVI

AV / S-Video / Component Mode

• AV / S-Video

PC / BNC / DVI Mode

• Component

PC / DVI Mode

• HDMI

PC / BNC Mode

Power button [ ]

Rear

Use this button for turning the LCD Display on and off.

Power indicator

Shows PowerSaver mode by blinking green

Note

See PowerSaver described in the manual for further information regarding power
saving functions. For energy conservation, turn your LCD Display OFF when it
is not needed or when leaving it unattended for long periods.

Remote Control Sensor

Aim the remote control towards this spot on the LCD Display.

Note

For detailed information concerning cable connections, refer to Connecting Cables under Setup. The
LCD Display 's configuration at the back may vary slightly depending on the LCD Display model.

Introduction

POWER S/W ON [ │ ] / OFF [O]

Switches the LCD Display On/Off.

POWER IN

The power cord plugs into the LCD Display and
the wall plug.

REMOTE OUT/IN

You can use a wired remote control by connecting
it to your LCD Display.

RS232C OUT/IN (RS232C Serial PORT)

MDC(Multiple Display Control) Program Port

DVI / PC / HDMI IN [PC/DVI/BNC AUDIO
IN] (PC/DVI/BNC/HDMI Audio Connection Ter­minal (Input))

DVI / PC / HDMI IN [HDMI]

Connect the HDMI terminal at the back of your
LCD Display to the HDMI terminal of your dig­ital output device using a HDMI cable.

DVI / PC / HDMI IN [RGB](PC Video Con­nection Terminal)

Using a D-Sub Cable (15 pin D-Sub) - PC mode
(Analog PC)

DVI / PC / HDMI IN [DVI(HDCP)] (PC

Video Connection Terminal)

Using a DVI Cable (DVI-D to DVI-D) - DVI
mode (Digital PC)

Introduction

COMPONENT AUDIO IN [L-AUDIO-R]
(Component Audio Connection Terminal (Input))

BNC/COMPONENT OUT [R/PR, G/Y, B/
PB, H, V] (BNC/Component Connection Termi­nal (Output))

BNC (Analog PC) Connection: connecting the R,
G, B, H, V ports

Component Connection: connecting the PR, Y,
PB ports

BNC/COMPONENT IN [R/PR, G/Y, B/PB,
H, V](BNC/Component Connection Terminal
(Input))

AV AUDIO IN [L-AUDIO-R] (LCD Display
Audio Connection Terminal (Input))

AV OUT [VIDEO](VIDEO Connection Ter­minal)

AV mode (Output)

AV IN [VIDEO](VIDEO Connection Termi­nal) (Input)

AV OUT [S-VIDEO] (S-VIDEO Connection
Terminal)

S-VIDEO mode (Output)

AV IN [S-VIDEO](S-VIDEO Connection
Terminal) (Input)

EXT SPEAKER(8 Ω)[- - L - +, - - R - +] (EXT
Speaker Connection Terminal)

AUDIO OUT [L-AUDIO-R] (LCD Display
Audio Connection Terminal (Output))AUDIO
OUT is the terminal for sound output of PC, DVI
or BNC.

See Connecting Cables for further information regarding cable connections.

-- 460DXn --

Introduction

LAN (LAN Connection Terminal)

USB(USB Connection Terminal)

Keyboard / Mouse, Mass Storage Device Com­patible.

Note

The number of LCD Displays that can be con­nected to loopout may differ depending on the
cables, signal source etc. With cables where there
is no degradation or signal source, up to ten LCD
Displays can be connected.

Note

Remote Control

Note

The performance of the remote control may be affected by a TV or other electronic device operating
near the LCD Display , causing a malfunction due to interference with the frequency.