Samson 8-5000 User Manual

If any components of this unit are broken,
ATTENTION
do not operate properly, or for product returns,
please contact Pragotrade at
1-800-814-4895
Outside the U.S. call 440-638-3131.
Exc lusiv ely impo rte d by Pra gotra de LLC, Str ongsv ill e, Oh io
www.pragotrade.com
COMMERCIAL
PRODUCTS
C O M M E R C I A L
WHEATGRASS JUICER
INSTRUCTION MANUAL
Model No. 08-5000
REV081809
12
2
11
Feed
Chute
3
A
B
4
Power
Cord
Power Switch / Circuit Breaker
Reset Button
10
Juice
1
Outlet
5
COMPONENT LIST
DIAGRAM PART PART NUMBER DESCRIPTION NUMBER
1 Head 08-5010
2 Juicer Motor N/A 3 Head Locking Screw 08-2005 4 Auger Bushing See Replacement Parts Kit 5 Screen See Replacement Parts Kit 6 Auger 08-5015 7 Rubber Gasket See Replacement Parts Kit 8 Head Aligning Cap 08-5017 9 Waste Valve 08-5018 10 Rubber Feet (4) 08-2007 11 Stomper 08-5020 12 Head Aligning Cap Wrench 08-5021
Not Shown Toggle Switch Rubber Boot 08-5012
13 Replacement Parts Kit 08-5022
Screen (2) Rubber Gasket (2) Auger Bushing (2)
A Complete Motor Assembly 08-5028 B Complete Head Assembly 08-5029
If an y parts a re miss in g or da maged, th e uni t does no t opera te proper ly or t o
repla ce worn -o ut part s call Pr agotrad e LLC t ol l free at
1-800-814-4895
Monday thru Friday 8:00am-5:00pm EST.
Outside the U.S. call 440-638-3131
-2-
WARRANTY INFORMATION
SAVE THIS WARRANTY INFORMATION FOR YOUR RECORDS!
Pragotrade LLC warrants to the ORIGINAL RETAIL PURCHASER of this product that if operated in accordance
with the printed instruction accompanying it, then for a period of 1 year from the date of purchase, the product shall be free from defects in material and workmanship. The Warranty Card, along with a copy of the original receipt, must be received by Pragotrade LLC within 30 days
from purchase date for the warranty to apply. Failure to send the completely lled out Warranty Card, along with a copy
of the original receipt, will void the warranty. The product must be delivered to or shipped freight prepaid to Pragotrade LLC for warranty services, in either its original packaging or similar packaging affording an equal degree of protection. Damage due to shipping is not the responsibility of the company. Pragotrade LLC charges a $35.00 per hour bench charge. NOTE: No repairs will be started without the authorization of the customer. The return shipping cost to the customer will be added to the repair
13
7
8
9
6
invoice. Pragotrade LLC will repair (or at its discretion, replace) the product free of charge, if in the judgment of the company, it has been proven to be defective as to seller’s labor and material, within the warranty period. New or rebuilt replacements for factory defective parts will be supplied for one (1) year from the date of purchase. Replacement parts are warranted for the remainder of the original warranty period. For non-warranty repairs, contact Pragotrade’s Customer Service at 1-800-814-4895 M-F 8am-5pm EST (outside of the United States 440-638-3131) to obtain a Return Authorization Number (RMA Number). Pragotrade will refuse all returns that do not contain this number. DO NOT RETURN THE UNIT WITHOUT PROPER AUTHORIZATION
FROM PRAGOTRADE LLC.
LIMITATIONS: The warranty is void if the product is used for any purpose other than that for which it is designed. The product must not have been previously altered, repaired, or serviced by anyone else other than Pragotrade LLC. If applicable, the serial number must not have been altered or removed. The product must not have been subjected to accident in transit or while in the customer’s possession, misused, abused, or operated contrary to the instructions contained in the instruction manual. This includes failure caused by neglect of reasonable and necessary maintenance, improper line voltage and acts of nature. This warranty is not transferable and applies only to U.S. and Canadian sales. Except to the extent prohibited by applicable law, no other warranties whether expressed or implied, including
warranty merchantability and tness for a particular purpose, shall apply to this product. Under no circumstances shall
Pragotrade LLC be liable for consequential damages sustained in connection with said product and Pragotrade LLC neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than such as is expressly set forth herein. Any applicable implied warranties are also limited to the one (1) year period of the limited warranty.
This warranty covers only the product and its specic parts, not the food or other products processed in it.
CUT ALONG THE DOTTED LINE AND SEND THE WARRANTY CARD ALONG WITH A COPY OF YOUR ORIGINAL PURCHASE RECEIPT TO:
Pragotrade LLC
20365 Progress Drive, Strongsville, OH 44149
COMMERCIAL WARRANTY CARD
SEND THIS CARD ALONG WITH A COPY OF YOUR ORIGINAL PURCHASE RECEIPT
Business Name: _________________________________
Contact Name: __________________________________
Address: ______________________________________
City/State/Zip: ___________________________________
Telephone Number: (_________) ___________________
E-Mail Address: ___________________________________
Original Date of Purchase: _______/_________/__________
Product Model #: __________________________________
Serial # (if applicable): ____________________________
-11-
HELPFUL HINTS
1. If you notice a decrease in juice output, the Screen may be clogged. You will need to disassemble the Wheatgrass Juicer (see “Cleaning Instructions” section of this manual) and clean the Screen before continuing.
2. See the “Using the Reverse Function” section of this manual for information on clearing a jam.
3. Spray the Drive Shaft of the Motor Body with a food-grade silicone spray after every cleaning.
WARNING!
NEVER operate Wheatgrass Juicer unless it is
fully and properly assembled.
To avoid serious or fatal injury, NEVER reach into any inlet or outlet.
ONLY USE the Stomper to push wheatgrass into the Head.
Read and understand all information in this manual before use.
-10-
IMPORTANT SAFETY RULES
READ AND FULLY UNDERSTAND ALL INSTRUCTIONS AND WARNINGS PRIOR TO USING THIS UNIT. YOUR SAFETY IS MOST IMPORTANT! FAILURE TO COMPLY WITH PROCEDURES AND SAFEGUARDS MAY RESULT
WARNING!
1. Read and understand all information in this manual before using the Wheatgrass Juicer.
2. Clean the Wheatgrass Juicer before
using it for the rst time and every time
after use. See the “Cleaning Instructions” section of this manual.
3. DO NOT use the Wheatgrass Juicer unless it is fully assembled and all parts are secured in place. See the “Assembly Instructions” section of this manual.
4. To avoid serious personal injury, NEVER reach into the Head. Use the
Stomper to push wheatgrass into the Head.
5. Stay clear of the juice outlet on the bottom of the Head. NEVER insert your
ngers into the juice outlet. Serious
personal injury could result.
6. Disconnect the Power Cord from the electrical outlet before cleaning, assembling or disassembling the Wheatgrass Juicer.
7. Only operate the Wheatgrass Juicer on a level, stable surface. Make sure all of the feet touch the surface.
8. To prevent unintentional starting, make sure the Power Switch on the Juicer
Motor is set to “OFF” before connecting the Power Cord to the electrical outlet.
9. DO NOT operate the Wheatgrass Juicer without wheatgrass in the Head.
Damage to the Head and Auger may occur.
10. Inspect the Power Cord for damage before each use. DO NOT use the Wheatgrass Juicer if the Power Cord or any other part is damaged. DO NOT attempt to repair the Wheatgrass Juicer. Call Pragotrade at the number listed on the back of this manual for information on unit
SAVE THESE INSTRUCTIONS!
IN SERIOUS INJURY OR PROPERTY DAMAGE.
REMEMBER: YOUR PERSONAL SAFETY IS YOUR RESPONSIBILITY!
repair or replacement.
11. DO NOT use parts or attachments from other manufacturers on the Wheatgrass Juicer. Use of unauthorized parts or attachments may cause personal injury and/or unit damage and will void the warranty.
12. DO NOT use the Wheatgrass Juicer outdoors.
13. Before operating the Wheatgrass Juicer, tie back long hair, roll up long sleeves and remove ties, watches and jewelry.
14. Wait until all parts have stopped moving before toggling the Wheatgrass Juicer into “Reverse” or “Forward”.
15. DO NOT run the Wheatgrass Juicer in “Reverse” for more than 3 seconds at a time. Damage to the unit may occur.
16. DO NOT use the Wheatgrass Juicer
while under the inuence of drugs or
alcohol.
17. DO NOT operate the Wheatgrass Juicer if the Juicer Motor is very cold. The temperature of the Juicer Motor should be at least 45oF (7oC) before use.
18. The body and Juicer Motor may become warm during use. This is normal. DO NOT touch these parts while the Wheatgrass Juicer is running or until they cool afterwards.
19. WEAR EYE PROTECTION. Wear safety glasses while operating the Wheatgrass Juicer. Everyday eye glasses are not safety glasses. Approved safety glasses conform to ANSI-287.1 requirements and will have Z87 printed or stamped on them.
Refer to them often and use them to instruct others.
-3-
GROUNDING INSTRUCTIONS
GROUNDING
This appliance must be grounded to protect the operator from electric shock during use. For this purpose, it is equipped with a three-conductor power cord and three-prong grounding-type plug (Figure
A). The plug only ts three-hole electric receptacles. For the plug to t a two-hole receptacle, you will
need a Grounding Plug Adapter with a wire or metal tab (Figure B). Connect the wire/tab to the electrical outlet with the cover plate screw. The screw must be metal. The electrical box must be properly grounded (Figure C).
3 prong
grounding-
type plug
Grounding
Plug
Aadaptor
Figure A
Figure B
WASTE VALVE SETTINGS
WARNING! Before cleaning, assembling or disassembling the
Wheatgrass Juicer, make sure it is turned “OFF” and the Power Cord is disconnected from the electrical outlet.
To extract the maximum amount of juice from wheatgrass, we recommend you fully close the Waste Valve (Figure 7). A different setting may result in more juice, though. Experiment by adjusting the Waste Valve in and out. Be careful not to remove the Waste Valve while the Wheatgrass Juicer is running.
Figure 7
Waste
Valve
EXTENSION CORDS
When using an extension cord with this appliance, only use a three-wire extension cord with a three-prong grounding-type plug and three-pole
Metal tab or
wire
Figure C
connector. The extension cord must have an electrical rating equal to or greater than that of the appliance. Do not use a damaged extension cord. Examine the cord before each use and replace it if necessary. Do not abuse an extension cord. Pull on the plug, not the cord, to disconnect it. Keep the extension cord away from hot surfaces and sharp edges.
Metal
Grounding
Screw
Cover of
Grounded
Outlet Box
CIRCUIT BREAKER INSTRUCTIONS
The Wheatgrass Juicer is equipped with a Circuit Breaker to protect it from damage due to overload or short circuit. If the Wheatgrass Juicer should unexpectedly stop running, take
the following steps to get it running again.
ALLOW MOTOR TO COMPLETELY STOP
BEFORE ENGAGING IN
FORWARD OR REVERSE.
READ & FULLY UNDERSTAND
ALL INSTRUCTIONS AND
WARNINGS PRIOR TO
USING THIS UNIT.
1. Turn the Power Switch to the “OFF” position.
2. Check for possible reasons for the overload, ie. a jam in the machine or incorrect assembly.
Circuit Breaker
Reset Button
3. Press the Circuit Breaker Reset Button (Figure 1).
4. Turn the Wheatgrass Juicer back on and resume juicing.
5. Resume normal operation.
If the Wheatgrass Juicer still does not run, check the household circuit breaker to see if it has tripped and/or try connecting the Power Cord to a different electrical outlet. If these steps don’t work or if the Circuit Breaker repeatedly trips, turn the unit off and disconnect it from the electrical outlet. DO NOT continue to try running the Wheatgrass Juice or unit damage may occur. Contact Pragotrade at the number on the back of this manual for information on unit repair or replacement.
-4-
Figure 1
USING THE REVERSE FUNCTION
NOTICE: DO NOT run the Wheatgrass Juicer in reverse for more than 3 seconds at a time. Unit damage may occur.
ALLOW MOTOR TO
Use the Reverse Function to improve
ow through the Wheatgrass Juicer when necessary. Briey engage “Reverse” to help
COMPLETELY STOP
BEFORE ENGAGING IN
FORWARD OR REVERSE.
READ & FULLY UNDERSTAND
ALL INSTRUCTIONS AND
WARNINGS PRIOR TO
USING THIS UNIT.
clear a jam, for example.
1. Turn the Power Switch to the “OFF” position.
2. Wait until the Juicer Motor comes to a complete stop.
3. Briey hold the Power Switch in the “Reverse” position (Figure 8). DO NOT hold the Power Switch in “Reverse” for more than about 3 seconds. Unit damage may occur.
4. The Power Switch will automatically return to “OFF” once released from the “Reverse” position.
If juice ow does not improve after engaging “Reverse” , disassemble, clear the jam and
clean the Screen holes before resuming operation.
Figure 8
Power Switch
WARNING!
NEVER operate Wheatgrass Juicer unless it is
To avoid serious or fatal injury, NEVER reach into any inlet or outlet.
ONLY USE the Stomper to push wheatgrass into the Head.
Read and understand all information in this manual before use.
fully and properly assembled.
-9-
OPERATING INSTRUCTIONS
WARNING! Before cleaning, assembling or disassembling the
Wheatgrass Juicer, make sure it is turned “OFF” and the Power Cord is disconnected from the electrical outlet.
WARNING!
NEVER operate Wheatgrass Juicer unless it is
To avoid serious or fatal injury, NEVER reach into any inlet or outlet.
ONLY USE the Stomper to push wheatgrass into the Head.
Read and understand all information in this manual before use.
1. Place a cup under the outlet on the bottom of the Head to collect juice. Place a cup or container under the Waste Valve to collect pulp (Figure 6).
2. Fill the Head with wheatgrass.
3. Make sure the Power Switch is in the “OFF” position. Connect the
Power Cord on the Juicer Motor to an electrical outlet.
4. Turn the Wheatgrass Juicer “ON” by pushing
the Power Switch to the “Forward” position.
5. Use the Stomper to push wheatgrass into the Head. DO
NOT use your ngers to push
wheatgrass into the Head!
6. Add wheatgrass to the Head as
needed to keep juice owing. Always
be careful. Keep your ngers clear
of the Head Opening.
7. Turn the Wheatgrass Juicer “OFF” and disconnect the Power Cord from the electrical outlet when you are done.
fully and properly assembled.
Head
Opening
KEEP FINGERS
CLEAR!
Power Switch
Figure 6
Waste
Valve
Juice
Outlet
PRIOR TO USE
Clean and sanitize the Wheatgrass Juicer as indicated in the “Cleaning Instructions”
section of this manual before using it for the rst time.
DO NOT IMMERSE THE JUICER MOTOR IN WATER OR OTHER LIQUIDS.
DISASSEMBLY INSTRUCTIONS
WARNING! Before cleaning, assembling or disassembling the
Wheatgrass Juicer, make sure it is turned “OFF” and the Power Cord is disconnected from the electrical outlet.
1. Turn the Wheatgrass Juicer to the “OFF” Position. Disconnect the Power Cord on the Juicer Motor from the electric outlet.
2. Loosen the Head Aligning Cap (on the Head) by turning it clockwise. DO NOT REMOVE the Head Aligning Cap at this time. Use the Head Aligning Cap Wrench if necessary.
3. Loosen the Head Locking Screw on the Juicer Motor until it releases the Head Assembly.
4. Remove the Head Assembly from the Juicer Motor.
5. Unscrew the Head Aligning Cap from the Head by turning it clockwise.
6. Unscrew the Waste Valve from the Head Aligning Cap by turning it clockwise.
7. Remove the Rubber Gasket from the Head Aligning Cap.
8. Remove the Auger and Screen from the Head.
9. Allow the parts to air-dry before reassembling and storing the Wheatgrass Juicer.
10. The Wheatgrass Juicer is NOT dishwasher safe.
CLEANING INSTRUCTIONS
WARNING! Before cleaning, assembling or disassembling the
Wheatgrass Juicer, make sure it is turned “OFF” and the Power Cord is disconnected from the electrical outlet.
JUICER MOTOR
1. Make sure the Power Cord on the Juicer Motor is disconnected from the electric outlet.
2. Clean the Juicer Motor by wiping it with a damp cloth. NEVER immerse the Juicer Motor in water or other liquid. DO NOT spray the Juicer Motor with water.
3. Dry the Juicer Motor before storing it.
HEAD ASSEMBLY, STOMPER & HEAD ALIGNING CAP WRENCH
1. Fill a sink with hot water. Maintain a water temperature of at least 140oF (60oC) throughout the washing process.
2. Add a manual dishwashing detergent formulated for commercial use to the water per the manufacturer’s instructions.
3. Place all parts to be washed in a sink.
4. Thoroughly wash all parts with a sponge or dishcloth. Be sure to fully remove any food residue from each part.
-5--8-
5. After washing, drain the sink and rell it with warm water.
6. Rinse the parts by submerging them in water. Change the water and repeat, if necessary, to remove all of the detergent.
7. When done rinsing, drain the sink and rell it with a sanitizing solution of water and chlorine
bleach (use 1 ounce of chlorine bleach per 4 gallons of water). Soak the parts in the solution for a minimum of 5 minutes.
8. Remove the parts from the sink.
9. Allow the parts to air-dry before reassembling and storing the Wheatgrass Juicer.
NOTE! The Wheatgrass Juicer is NOT dishwasher safe.
ASSEMBLY INSTRUCTIONS
WARNING! Before cleaning, assembling or disassembling the
Wheatgrass Juicer, make sure it is turned “OFF” and the Power Cord is disconnected from the electrical outlet.
1. Slide the Screen (curved side down) into the slot on the inside bottom
of the Head until it stops. Make sure both sides of the Screen are within the slot (Figure 2).
2. Place the Auger Bearing onto the splined end of the Auger. Insert the the Auger into the open end of the Head until it stops. The splines on the end of the Auger should protrude from the opposite end of the Head (Figure 3).
3. Place the Rubber
Gasket onto the at surface on the inside of the Head Aligning Cap below the threads. The Rubber Gasket is properly installed
when it lays at on the
surface (Figure 4).
4. Screw the Head Aligning Cap counterclockwise onto the Head until it
is rmly seated.
5. Screw the Waste Valve counterclockwise into the tip of the Head Aligning Cap until it stops.
7. Loosen the Head Locking Screw on the Juicer Motor until it no longer protrudes into the receptacle for the Head Assembly (Figure 4).
8. Install the Head Assembly onto the Juicer Motor. You will need to align the cutout on the Head with the pin inside
CAUTION:
Make sure Screen is properly seated
in the slot before operation or unit
damage will occur.
Head
Auger
Bearing
Figure 4
Head
Slot
Auger
Splines
Auger
Rubber
Gasket
Head
Aligning
Cap
Figure 2
Screen
Figure 3
Waste
Valve
the receptacle (Figure 5). Align the Auger Splines with the keyways on the drive shaft of the Juicer Motor. If the parts do not align, rotate the Auger end (it protrudes from the Head) a bit and try again. Wiggling the Head Assembly during installation may help as well.
IMPORTANT: Tighten the Head Locking Screw until it rmly holds the Head Assembly in place.
CAUTION!: DO NOT operate the Wheatgrass Juicer without the
Head Assembly rmly secured
into place. Personal injury or unit damage may occur.
Pin Inside
Receptacle
Head
Locking
Screw
WARNING!
NEVER operate Wheatgrass Juicer unless it is
To avoid serious or fatal injury, NEVER reach into any inlet or outlet.
ONLY USE the Stomper to push wheatgrass into the Head.
Read and understand all information in this manual before use.
fully and properly assembled.
-7--6-
Cutout
In Head
Figure 5
Loading...