SAGEMCOM DCI85HD KD User Manual

Download

Page 1

User manual

RECEIVER

DCI85HD KD

Page 2

Page 3

DCI85HD KD

Congratulations!

This Receiver is an innovative product from the latest generation of Sagemcom digital TV receivers, dedicated to Digital Cable Television. It allows easy reception of digital programs, including those broadcast in High Definition.

Once you have connected your Receiver and performed the initial installation, you will be able to watch and enjoy all the cable TV and radio channels which are not scrambled and you are entitled to. You can update your Receiver if new functions or services become available.

The Sagemcom Receiver follows a continuous development strategy. Therefore, we reserve the right to make changes and improvements to the product described in this user manual without any prior notice.

This product complies with EMC directive 89/336/EEC.

CE marking:

The CE marking certifies that the product complies with the essential requirements of the Directive 1999/5/EC concerning radio equipment and telecommunication equipment, and of Directives 2006/95/EC concerning safety, 2004/108/EC concerning electromagnetic compatibility and ErP 2009/125/EC concerning ecodesign requirements, defined by the European Parliament and Council to minimize electromagnetic interferences, ensure the safety of users and their equipment and protect their health, and minimize the impact of products on the environment.

The CE declaration of conformity can be viewed in the support section of the Sagemcom site www.sagemcom.com, or it can be obtained from the following address:

Sagemcom Broadband SAS - Customer relations department

250 route de l'Empereur

92848 Rueil-Malmaison Cedex - FRANCE

This "HD TV" Television Receiver complies with the "HD TV" Minimum Requirements. The "HD TV" Logo is a trademark of DIGITALEUROPE. HDMI, HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. DTS is a registered trademark of Digital Theater Systems, Inc. Macrovision is a registered trademark of Rovi Corp. Manufactured under license from Dolby Laboratories. "Dolby" and the double-D symbol are registered trademarks of Dolby Laboratories Inc.

Macrovision Copyright notice

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Rovi Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Rovi Corporation. Reverse engineering or diassembly is prohibited.

Page 4

DCI85HD KD

Read this first!

For your safety and comfort, we urge you to carefully read the Safety recommendations on page 3 before attempting use.

This document makes use of symbols designed to help the reader identify the information supplied:

Symbol Definition

CAUTION

Indicates important safety information.

Failure to respect these notes may lead to serious or even fatal injury. Read these notes carefully. You will find them in the Safety section of this manual.

WARNING

Indicates important safety information.

Failure to respect these notes may lead to minor to moderate injury, or damage to the apparatus or equipment. Read these notes carefully. You will find them in the Safety section of this manual.

Important

Indicates points to be read with special attention when using the device, and explanations of probable reception issues. Read these explanations carefully.

Note

Indicates additional explanations about device functions, and instructions for resolving user errors.

Page 5

DCI85HD KD

Safety recommendations

Use of the Receiver is subject to safety measures designed to protect users and their environment.

Where to put your Receiver?

In order to guarantee the correct operation of your Receiver, you must:

• place it indoors to protect it from lightning, rain, and sun rays,

• place it in a dry and well ventilated area,

• keep it away from heat sources such as radiators, candles, lamps,

etc.

• protect it from dampness, place it on a flat surface from where it

will not fall off and children don`t have access to,

• do not place anything on top of your Receiver (as it would restrict

ventilation): the ventilation slots located on the casing prevent your Receiver from overheating. If you place the Receiver in a compartment, leave a space of at least 10 cm on each side and 20 cm on the front and back of the Receiver,

• connect it directly to the mains with the provided cords, the socket

must be near the Receiver and easy to access. The use of an extension cable (with multi-points) is not recommended.

Warnings and safety instructions

NEVER OPEN THE Receiver! YOU RISK GETTING AN ELECTRIC SHOCK.

• Use only the power cord supplied with the Receiver to connect it to the mains. Other

practice may be dangerous.

• Connect the Receiver to the mains in accordance with the installation instructions in this

document and the indications mentioned on the identification label (voltage, current, frequency of electricity network).

• As a precaution, in case of danger, the mains adapters act as a disconnecting mechanism

for the 230V power supply. That is why it is imperative that you connect the Receiver to a power outlet located nearby and easily accessible.

•The Receiver must be used within a temperature range of between 0 °C and 40 °C.

• You must imperatively connect the power cord to the Receiver before connecting the power cord to the

power socket.

• To avoid short-circuits (fire or electrocution hazard), do not expose your Receiver to dampness. Do not

place any object containing liquid (vase for example) on the appliance. The Receiver must not be splashed with liquid. If liquid is dropped, dripped onto the Receiver, unplug it immediately from the mains and consult your supplier.

• Take care not to allow liquids or metal objects to enter the Receiver through the ventilation slots.

• Avoid reconnecting the Receiver after it has been subjected to large changes in temperature.

• The Receiver must be disconnected from mains supply (from the power outlet or rear panel) before

any modification of connection between TV, VCR or antenna.

• In the event of a storm, it is advisable to unplug the antenna. Even if the Receiver and the television

set are disconnected from the power supply, lightning can still damage them.

• Only a personnel approved by the manufacturer can repair the Receiver. The non-observance of these

safety precautions can result in forfeiture of the guarantee.

Page 6

DCI85HD KD

Batteries

Batteries are easily swallowed by young children. Do not allow young children to play with the remote control.

To avoid damaging the remote control, only use identical batteries or batteries of equivalent type. The batteries provided are not rechargeable.

Interference

Do not place the Receiver near appliances that may cause electromagnetic interferences (for example loudspeakers). This could affect Receiver operation and distort the picture or sound.

Cleaning the Receiver

The outer casing of the Receiver can be cleaned with a soft and dry cloth. Do not use any type of abrasive pad, scouring powder or solvents, such as alcohol or turpentine, as they could damage the surface of the Receiver.

Page 7

DCI85HD KD

Environment

Preservation of the environment is an essential concern of the manufacturer. The desire of the manufacturer is to operate systems observing the environment and consequently it has decided to integrate environmental performances in the life cycle of its products, from manufacturing to commissioning, use and elimination.

Meaning of logos present on the product or its packaging

The crossed-out dustbin sign stuck on the product or its accessories means that at the end of its life, the product is subject to selective collection and must not be thrown away in unsorted household waste.

The looped arrow sign means that the packaging may be recycled and must not be disposed of with household waste.

The green logo means that a financial contribution is paid to an approved national organisation to improve packaging recovery and recycling infrastructures.

The logo with three arrows shown on the plastic parts means that they may be recycled and that they must not be disposed of with household waste.

Product recycling and disposal

To facilitate recycling, please respect the sorting rules set up locally for this kind of waste.

If your product contains batteries, they must be disposed of at appropriate collection points.

European regulations ask you to dispose of products belonging to the family of electrical and electronic

equipments ( ) selectively:

• At the collection points made available to you locally (drop-off centre, selective collection, etc.),

• At sales points in the event of the purchase of similar equipment.

In this way you can participate in the re-use and upgrading of Electrical and Electronic Equipment Waste, which can have an effect on the environment and human health.

European Directive on Waste Electrical and Electronic Equipment (WEEE)

In the context of sustainable development, the reduction of wastes to be eliminated by reusing, recycling, composting and energy recovery is strongly advised.

In order to comply with this directive which is applicable to EEEs sold after 13/08/2005, your Receiver will be taken back free of charge and recycled by the distributor of the EEE within the limits of the quantity and types of equipment bought from them. These appliances which contain substances potentially dangerous to human health and the environment will be recycled.

Page 8

DCI85HD KD

Directive on the Restriction of use of certain hazardous substances in electronic

equipment (ROHS)

Your Receiver along with the batteries supplied comply with the directive relating to the RoHS – dangerous materials such as lead, mercury or cadmium are not used. This avoids environmental hazards and any risks to the health of personnel at the recycling centres. The batteries of the remote control can be removed simply.

Note: When the batteries of the remote control are worn out, please dispose of them at a collection point and not with household waste.

Electrical consumption of the Receiver

To reduce the consumption of your Receiver, you are recommended to place it in standby mode when not in use. We recommend you to turn off the Receiver or unplug it from the mains if you will not be using it for a prolonged period of time.

Page 9

DCI85HD KD

Contents

1. Product Overview ....................................9

1.1 Package contents ......................................... 9

1.2 Elements and functionalities: Front side

of the device ............................................... 10

1.3 Elements and functionalities: Back side

of the device ............................................... 10

1.4 Remote control ........................................... 11

Batteries .............................................................11

2. Connections to the network and

connecting additional devices ..............12

2.1 Connection to the cable network ................ 12

RF Cable connection..........................................12

2.2 Connection to TV ........................................ 13

Connection to High Definition TV with

HDMI® port ........................................................13

Connection to a standard definition TV

with SCART connection .....................................13

2.3 Connection to the internet........................... 14

Internet connection via wireless stick .................14

Internet connection via network cable ................14

2.4 Connection to the VCR / DVD recorder ...... 14

2.5 Connection with a home cinema amplifier .. 15

2.6 Connection to a hi-fi unit ............................. 15

2.7 Powering On / Off the Receiver .................. 16

3. Initial installation ....................................17

3.1 Preparation: Device checks the device

settings ....................................................... 17

3.2 Language settings ...................................... 17

3.3 The five steps of the installation wizard ...... 18

Step 1: Channel search......................................18

Step 2: Set up favorite channels ........................18

Step 3: Setting up an internet connection ..........19

Step 4: Select energy mode ...............................20

Step 5: Summary................................................20

4. Basic functions ......................................21

4.1 Selecting a TV channel............................... 21

Using P+/P- or 0-9..............................................21

Program information bar.....................................21

Using the channel list .........................................22

Detailed program information .............................23

4.2 Volume settings .......................................... 23

Volume ...............................................................23

Mute ...................................................................24

4.3 Language settings for audio and subtitles

and selection of option channels.................. 24

Language for audio............................................ 24

Language for subtitles ....................................... 24

Selecting option channels.................................. 24

4.4 Teletext ....................................................... 25

4.5 Listen to radio.............................................. 25

Selecting a radio channel .................................. 26

Categories and other options in radio mode...... 26

5. Setting a timer ....................................... 27

5.1 Set timer...................................................... 27

Set flags in program information bar.................. 27

Set timer in electronic program guide (EPG) ..... 27

Set timer in search results ................................. 28

Delete timer ....................................................... 28

5.2 Set timer manually....................................... 28

5.3 Displaying and using timers ........................ 29

6. Electronic program guide (EPG), search function and Select Video

(video library) ........................................ 31

6.1 Electronic Program Guide (EPG) ............... 31

6.2 Search ........................................................ 32

Search by keyword ............................................ 32

Search by category............................................ 33

Search results.................................................... 34

Local Search...................................................... 34

6.3 Select Video (online video library)............... 35

Access to Select Video ...................................... 35

Selection of videos............................................. 35

7. Settings ................................................. 37

7.1 System Update............................................ 37

Software update................................................. 37

Search for updated software.............................. 37

Channel search.................................................. 38

Delete additional channels................................. 39

Search additional channels................................ 39

Start a channel search....................................... 39

Reset to factory default...................................... 40

Update EPG....................................................... 40

7.2 System set-up ............................................. 41

Language........................................................... 41

Audio.................................................................. 41

Picture................................................................ 43

Energy settings .................................................. 45

Internet............................................................... 46

Page 10

DCI85HD KD

7.3 Protection of minors.................................... 50

Change Parental Control PIN.............................50

Change Adult PIN...............................................51

PIN request when ordering Select Video ...........51

PIN-protect timer ................................................52

7.4 Timer settings ............................................. 52

Manual timer.......................................................52

Timer extensions ................................................53

7.5 Favorites ..................................................... 53

Add favorites ......................................................53

Delete favorites ..................................................54

Sort favorites ......................................................54

7.6 Service........................................................ 55

Support by phone ...............................................55

Service messages ..............................................55

7.7 System Check ............................................ 55

Device Info .........................................................55

Smartcard...........................................................56

TV Signal............................................................56

VOD Signal.........................................................56

HDMI ..................................................................56

TV picture ...........................................................56

Audio ..................................................................56

Network settings.................................................57

Back channel......................................................57

Test IP Connection.............................................57

7.8 Settings overview........................................ 58

8. Software update .....................................62

9. Universal remote control .......................63

9.1 Programing the universal remote control.... 63

9.2 Selection of the volume control................... 64

9.3 Reading out the 4-digit code....................... 64

9.4 Reset the universal remote control ............. 64

9.5 Brand Code List .......................................... 65

10. Troubleshooting .....................................74

11. Support ...................................................75

12. Explanation of terms .............................76

13. Specifications .........................................77

Page 11

DCI85HD KD

1 Product Overview

Your Receiver is a digital receiver that lets you watch all the cable TV and radio channels which are not scrambled and you are entitled to.

1.1 Package contents

The package of your new device includes:

In addition, a smartcard from Kabel Deutschland is provided for the operation of the device.

Item Description

1 Receiver

2 Power cord

3 Remote control with 2 batteries (AAA)

4 HDMI lead for connection to the HDTV

5 Antenna cable to connect to the cable network

6 Quick installation guide

7 WLAN-Stick and cable

234

13 14

20 21

31 32

37 38

/Radio

Menü

Suche

ahmen

Zurück Info

Rec

Opt

321

Page 12

DCI85HD KD

1.2 Elements and functionalities: Front side of the device

1.3 Elements and functionalities: Back side of the device

Item Description Item Description

STANDBY button

TV/radio button

Switch to Standby/Wake up from standby

• Red: Device in standby

• Green: Device is running

Switch between TV and radio channels

• orange: radio mode active

USB port

P+/P- changing channels

Item Description Item Description

On/Off switch

DIGITAL AUDIO connector

(Optical S/PDIF)

6 Power supply connector 12 SCART connector (to TV)

Ethernet port (RJ45)

SCART connector (to VCR or

DVD Recorder)

8 USB port 14 Cable signal output

Analog AUDIO connectors (ANALOG AUDIO L/R) to Hi-fi system or TV

Cable signal input

HDMI DIGITAL VIDEO AUDIO connector

Page 13

DCI85HD KD

1.4 Remote control

Batteries

The remote control needs two batteries (AAA) to operate. The direction to insert the batteries is labeled in the battery compartment. The batteries are not rechargeable.

Button Functions

TV: Switch to TV mode, if programed. In TV mode, you can control your TV with this remote (see chapter 9, Using the universal remote). The unit is in TV mode, the LED light

flashes.

MENÜ: Open and close main menu

PROGRAMM: Show electronic program guide (EPG)

SELECT VIDEO: Open online video library Select Video

(Video on Demand, VOD), internet connection necessary. This service is not yet available everywhere in Germany.

V+/V-: Adjust the volume

NAVIGATION: Browse menu, electronic program guide (EPG),

program information bar and other functionalities

ZURÜCK: Return to the previous screen or mode

MUTE: Turn the sound on or off

REWIND: Rewind program or recorded program, switch to

other day in electronic program guide (EPG)

REC: Timing a program or prepare a timer using the electronic

program guide (EPG).

COLOR KEYS: Select options in the On Screen Display

(OSD), menus and messages, that are displayed on the screen

0-9: Choose programs and options from the On Screen

Display (OSD)

OPT: Displays options for the current program (Audio

Language / Subtitle, option channels). Shows program information for prime time in electronic program guide (EPG)

STANDBY: Switch to Standby/Wake up from standby

TV/RADIO: Switch between TV and radio channels

EXIT: Close a screen or a mode, return to the last viewed

program, switch from TV mode to Receiver mode

AUFNAHMEN: : Displays the timed program list

SUCHE: Starts a search for programs in electronic program

guide (EPG), in online video library Select Video and recordings

P+/P-: Jump to next / previous channel, display next / previous

page in electronic program guide (EPG), browse in multipage lists / references

OK: Show program information bar, confirm a selection

INFO: Show informations for current program, in electronic

program guide (EPG) and program search

FAST FORWARD: Forward switch to other day in the

electronic program guide (EPG)

PLAY/PAUSE: Play / pause a recorded program, switch to

time-shifted mode

STOP: Stop a recording, stop playing a recorded program,

stop the time shift mode and return to live TV program

TELETEXT: Show teletext pages, if available

Page 14

DCI85HD KD

2 Connections to the network and connecting

additional devices

Check if the package is complete before installing the Receiver (see chapter 1.1, Package contents).

Make sure that the devices to be connected (Receiver, TV, VCR ...) are disconnected from the power supply.

2.1 Connection to the cable network

To make sure that your Receiver can receive all the cable TV and radio channels which are not scrambled and you are entitled to, you must check first of all that your home is connected to cable network.

2.1.1 RF Cable connection

1. Connect the antenna cable input of the Receiver with the antenna socket (antenna cable provided).

2. Connect the antenna cable output of the Receiver with the antenna socket of the TV or VCR/DVD

Recorder (antenna cable not provided).

ANALOG

AUDIO

KABEL

EINGANG

KABEL

AUSGANG

VCR SCART TV SCART

DIGITAL

AUDIO

HDMI

NETZWERK

USB

EIN / AUS

19W

230V~50Hz

Page 15

DCI85HD KD

2.2 Connection to TV

2.2.1 Connection to High Definition TV with HDMI® port

In order to take advantage of high-definition television (HDTV), connect the HDMI® port on your digital Receiver through the HDMI

cable (provided) to the HDMI ® port on your HD TV.

2.2.2 Connection to a standard definition TV with SCART connection

Connect the TV SCART connector on the Receiver through a SCART cable (not provided) with a free SCART socket on your TV.

Note

If you have a TV with HDMI

port, please use only the HDMI® cable to connect

the Receiver to TV.

ANALOG

AUDIO

KABEL

EINGANG

KABEL

AUSGANG

VCR SCART

TV SCART

DIGITAL AUDIO

HDMI

NETZWERK

USB

EIN / AUS

19W

230V~50Hz

ANALOG AUDIO

KABEL

EINGANG

KABEL

AUSGANG

VCR SCART TV SCART

DIGITAL

AUDIO

HDMI

NETZWERK

USB

EIN / AUS

19W

230V~50Hz

Page 16

DCI85HD KD

2.3 Connection to the internet

With an internet connection you have numerous other offers from Kabel Deutschland. To use them, connect your Receiver to the internet, either through the wireless stick or via a network cable (LAN cable).

2.3.1 Internet connection via wireless stick

Slide the WLAN-Stick into the USB port for the WLAN dongle below the Network connector (RJ45). If the Receiver is connected to the power supply after all devices were connected, the wireless stick automatically starts. You may be prompted to enter the necessary data later.

2.3.2 Internet connection via network cable

If you wish to connect your Receiver to the internet using a network cable with RJ45 connectors (LAN cable), plug in such a network cable (not provided) into the network port (RJ45) on the back of the Receiver. Plug the other end of the network cable to a free network connection to your internet router. You may be prompted to enter the necessary data later.

2.4 Connection to the VCR / DVD recorder

Connect the VCR SCART connector on the back of your Receiver with a free SCART socket on your VCR-/DVD-Recorder (cable not provided).

Note

If your VCR / DVD recorder has more than one SCART socket, select the TV or EXT1 port.

NETZWERK

USB

NETZWERK

USB

ANALOG

AUDIO

KABEL

EINGANG

KABEL

AUSGANG

VCR SCART TV SCART

DIGITAL AUDIO

HDMI

NETZWERK

USB

EIN / AUS

19W

230V~50Hz

EXT

DIGIT

AUDIO

HDMI

Page 17

DCI85HD KD

2.5 Connection with a home cinema amplifier

Some programs are broadcast with DTS or DOLBY DIGITAL sound. To fully enjoy this high sound quality it is recommended to connect your Receiver via the optical S / PDIF connection with a home cinema amplifier.

Use an optical S / PDIF cable (not supplied) to connect the DIGITAL AUDIO port of the Receiver to the DIGITAL AUDIO port of the home cinema amplifier.

2.6 Connection to a hi-fi unit

To enjoy digital broadcasts in high sound quality and to listen to radio channels with switched off TV, connect the two analog AUDIO terminals (ANALOG AUDIO L / R) of the Receiver to the AUDIO terminals of your hi-fi system (cable not provided). This is only possible if you do not use the two analog AUDIO terminals (ANALOG AUDIO L / R) of the Receiver for connecting a TV.

ANALOG

AUDIO

KABEL

EINGANG

KABEL

AUSGANG

VCR SCART TV SCART

DIGITAL AUDIO

HDMI

NETZWERK

USB

EIN / AUS

19W

230V~50Hz

HDMI

ANALOG

AUDIO

KABEL

EINGANG

KABEL

AUSGANG

VCR SCART

TV SCART

DIGITAL

AUDIO

HDMI

NETZWERK

USB

EIN / AUS

19W

230V~50Hz

Page 18

DCI85HD KD

2.7 Powering On / Off the Receiver

You have all the equipment (Receiver, TV, VCR) connected? Connect the Receiver to the power network and turn it on. To turn on the Receiver proceed as follows:

1. Make sure that the power switch "On / Off" on the back of the Receiver is set to "Off" (position 0).

2. Now connect the power cord to the power connector of the Receiver.

3. Plug the power cord into a power outlet near the equipment so you can easily access it.

4. Press the "On / Off" button to switch the Receiver on (position I).

The initial installation of your Receiver will start automatically.

If you need to turn off the Receiver (for example, before a long period without using it), proceed as follows:

1. Press the STANDBY button on the remote control or on the front of the Receiver to switch the Receiver

to standby mode.

2. Press the "on / off" switch on the back of the Receiver to turn off the Receiver (position O).

3. Unplug the power cord from the socket.

ANALOG

AUDIO

KABEL

EINGANG

KABEL

AUSGANG

VCR SCART

TV SCART

DIGITAL AUDIO

HDMI

NETZWERK

USB

EIN / AUS

19W

230V~50Hz

Page 19

DCI85HD KD

3 Initial installation

If the Receiver is plugged in and turned on for the first time, the installation wizard starts.

1. Turn on your TV. If your TV does not automatically recognize the connected and powered Receiver,

select the AV source to your TV (HDMI ®, analog or SCART AUDIO / VIDEO connector), on which the TV is currently connected to the Receiver.

2. Open the cover of the smartcard reader on the front of the

Receiver. Slide the smartcard into the card slot. The smartcard must be inserted with the chip facing down.

3.1 Preparation: Device checks the device settings

The following tests are performed by the installation wizard automatically. Your intervention is not required normally.

The Receiver searches for the cable signal. If no signal is detected, make sure that the antenna cable is

properly connected. If the test has been interrupted, press on your remote control to proceed with the

installation.

If the Receiver does not find a signal, contact the customer service of Kabel Deutschland.

The Receiver verifies that you have inserted the smartcard into the device. You received a smartcard from Kabel Deutschland, insert it into the smartcard reader. The smartcard must be inserted with the gold chip

facing down. If you do not have the smartcard at hand, press on the remote control to continue the

installation without smartcard. Until you use the smartcard, you can only use free channels.

The Receiver automatically searches the cable network for new and improved software for your Receiver. If new software is available, the Receiver downloads it and reboots.

3.2 Language settings

The default language for the operation of your Receiver is

German. If you want to set a different language, press

on the remote control. You can choose between the languages German, English, Turkish and Russian. Use the keys to select

a language and confirm your selection by pressing .

Note

The assignment of the button on your remote changes depending on

the steps you perform. During installation, the current function assignment of

the button always appears at the bottom right on your television

screen.

Page 20

DCI85HD KD

3.3 The five steps of the installation wizard

In five steps, the installation wizard will guide you through the installation. Please follow the instructions on the screen carefully. If necessary, react with your remote control. Simply use the keys around the

button and then confirm your selection by pressing .

3.3.1 Step 1: Channel search

The Receiver automatically checks the cable for TV and radio channels and stores them in places 101 to

999.

After the completion of the channel search, the total number of TV and radio channels is displayed in the installation

screen. Exit the channel search by pressing .

3.3.2 Step 2: Set up favorite channels

The channel search normally finds several hundred channels. You can now set up your favorite channels and their place in the list of favorite channels. Places 1 to 100 are reserved for

your favorites. To begin, press .

1. The list of TV channels is displayed. Now proceed by pressing the keys , or the P+ / P- button on

your remote control to browse through the channel list and select which channel you want to add to your

favorites list. If you want to add a channel to your favorites list, press while the yellow marker is on

the name of the channel. The selection is indicated by a green check mark next to the channel name.

2. If your list is complete, press on the remote control. A window appears in which you are prompted to

confirm your selection. By pressing you store your entire favorite list.

3. To change the order of the channels in your favorites list, move down with the arrow key to the entry

Rearrange. Your favorites are displayed. Do you want to move a channel in the favorites list, press

while the yellow marker is on the program‘s name. Now the program can be moved using the keys

4. To complete sorting, press the arrow button . Confirm the selected order of your favorites list by

pressing .

Note

If you do not want to create a list now, skip this menu. You can later press

on your remote to enter the main menu. Then select Settings first,

then Favorites (see chapter 7.5, Favorites). By choosing Add the list of TV channels is displayed. You can now create your favorites list as described. Without a favorites list the positions 1 to 100 remain unassigned.

Page 21

DCI85HD KD

3.3.3 Step 3: Setting up an internet connection

If you are connected to the internet you can use the Kabel Deutschland’s online video store "Select Video". This service is not yet available everywhere in Germany. Furthermore, by using an internet connection you can review previous searches, the list of your recorded programs and a list of your favorite channels.

On the TV screen you see how to connect the Receiver to the internet. Select how to connect to the internet using the keys , on the remote control: via the provided wireless stick or via a network cable (LAN cable) (with network cable, continue with step 2).

If you do not want to connect the Receiver to the internet at the moment, use the arrow button and on your remote control to select Proceed to step 4: Select Energy Save Mode.

1. If you want to connect via the WLAN-Stick, make sure that

the WLAN-Stick is plugged into the USB port for WLANStick under the network connector (RJ45) on the back of the Receiver and that the WLAN key is at hand. The wireless key is a string in the form of a password that protects access to your wireless internet access from unauthorized third parties. The wireless key is usually found in the documentation of your wireless router, the wireless access point to the internet. It is strongly discouraged to operate a wireless internet access in Germany without protection by a wireless key for reasons of data protection, data security and for legal liability.

Now select the yellow highlighted line Via the Kabel Deutschland wireless LAN stick by pressing on your

remote to establish an encrypted connection between WLAN-Stick and wireless router using a WLAN key. You have additionally the option of selecting Continue with WPS using the arrow key on your remote control. WPS stands for Wi-Fi Protected set-up and is another technology for establishing wireless connections, but with lower level safety. If wireless networks are in range, they are now displayed. Choose with the keys , on the remote control, with which wireless network to connect the Receiver. When the name of the network is

highlighted in yellow, select this network pressing on your remote.

Now, an on-screen keyboard is displayed to type the WLAN key. The wireless key is usually between 8 and 63 characters long and can consist of numbers, letters and special characters. Usually you have to distinguish between lowercase and uppercase letters. To enter the WLAN key, move the yellow highlight using the four keys , , , on your remote control to the first character of the Wi-Fi key,

and then press on your remote control. The character appears in the input line on the screen keyboard. Enter all characters of the wireless key. Use the ABC field in the screen keyboard and press

on your remote to set the lowercase letters shown in the screen keyboard to uppercase if

necessary. Use the field !&? in on the on-screen keyboard and press on your remote to display

the special characters available. If the key is entered completely and correctly, finish the input via the field Input ready on the on-screen keyboard and press on your remote control. Now, the Receiver

checks the network and internet connection. If the Receiver is connected to the internet, the message The internet connection has been set up appears. In addition, the LED light flashes on the wireless stick.

EIN / AUS

23W

230V~50Hz

ANALOG

AUDIO

USB

NETZWERK

HDMI

Page 22

DCI85HD KD

2. If you choose to connect via a network cable (LAN cable), check if the network cable is connected to

the Receiver and to the router as shown in chapter 2.2.2, Connection to a standard definition TV with SCART connection. Press and on your remote control to select Via a LAN cable. The

device will automatically establish an internet connection.

If the internet connection is lost, it can be established later pressing on your remote control and selecting Settings (see chapter 7.2.5, Internet).

3.3.4 Step 4: Select energy mode

In the fourth step you decide whether your Receiver consumes less energy overall but starts slowly, or if you wish a rapid operation of the Receiver but want to take into account a higher overall energy consumption of the device. Select one of the modes: Active, Quick Start and Keep Standard.

The default is the Standard mode, it causes the lowest power consumption and a longer start-up phase.

The Active mode has the highest power consumption and keeps the equipment ready at any time.

The Quick Start mode allows you to choose the times at which the device remains in Active mode and

when it falls into the Standard mode. Use the keys , and press on your remote control to select

one of the specified modes. If you have selected the Quick Start mode, enter the start time, for example 1 7 0 0 for 17:00 hrs

(=5 p.m.), using the number buttons on your remote control.

Use the arrow button and press on your remote control, to select for how many hours the Receiver

shall remain active. Use the arrow button and press on your remote control to choose on which days this mode should be active, for example, Daily or only on Mondays, Wednesdays and Sundays.

Save your settings pressing on your remote.

The message The Energy Mode has been selected appears on the TV screen, confirm it pressing on your remote.

You may press on your remote control and Settings at any time to change the power mode later (see chapter 7.2.4, Energy settings).

3.3.5 Step 5: Summary

After choosing the power saving mode in step 5, you receive a summary of the successful installation. Now you will see a list of the settings you have made during the installation.

Now press on your remote to confirm the yellow marked field Watch TV and go to the TV program.

Page 23

DCI85HD KD

4 Basic functions

4.1 Selecting a TV channel

4.1.1 Using P+/P- or 0-9

To change channels press the P+ or P- button on the remote control or enter the channel number directly using the numeric keys on the remote control. You can also switch to the last viewed channel using the

button .

4.1.2 Program information bar

Each time you change the channel, the program information bar appears on the TV screen. It can also be

displayed while watching a program by pressing or using the four keys , , , .

The program information bar shows you the current program and the program for the coming 2 hours at a glance.

Use the keys and to scroll through the information regarding the current program and upcoming

programs. You can display the time and the transparency of the information bar pressing on your remote and Settings, System set-up, Picture, OSD Transparency (see chapter 7.2.3.6, OSD

Transparency).

A Day of broadcast E Current and next program

B Channel number and name F Channel category

Title, start time and end time of the broadcast

G Choose category

D Elapsed time H Show options for this program

HGF

C D

Page 24

DCI85HD KD

4.1.3 Using the channel list

During a program you can display the program information bar by pressing on your remote control or

using the four keys , , , .

Press or to display the channel list.

Press and to scroll through the channel list (I). The program information bar shows the broadcast data for the selected channel (J).

To switch to a channel in the list, mark it with the buttons or , then press .

4.1.3.1 List of favorites

If you have favorite channels you watch frequently, you can add them to your TV favorites list in the program information bar: your favorites are listed first for faster selection (channels 1 to 100 depending on the number of favorites). The main channel list follows, from channel number 101 to 999 depending on the number of channels found in the cable network.

For more information about creating and managing favorites, see chapter 7.5, Favorites.

4.1.3.2 Categories

To allow easy access to channels in a particular category, proceed as follows: press the yellow button on

the remote control, select a category using the buttons or and press . The Channel list now

shows the first channel in the selected category.

Page 25

DCI85HD KD

4.1.4 Detailed program information

To view more information about a program, press . Depending on availability, a detailed description

of the program is displayed.

Use the keys P+ or P- to scroll through the information pages.

Depending on the mission, you can select different actions within the information page:

Use the buttons or to select an action and press to confirm.

To close the program information screen and move to the last viewed program, press or .

4.2 Volume settings

4.2.1 Volume

Adjust the volume using the volume buttons on your remote control. If you want to increase the volume, press +. If you want to decrease the volume, press -.

Action Description

Watch View the program.

Watch in HD

Watch the channel in HD if you have an activation for the selected channel.

Timer Set the timer.

Channel to favorites Add the channel broadcasting the program to the Favorites.

Note

The following settings affect the sound that can be heard on TV, but not on the VCR SCART connector, on the analog AUDIO connector (ANALOG AUDIO L / R) for Hi-fi system and on the DIGITAL AUDIO port.

Page 26

DCI85HD KD

4.2.2 Mute

If you want to mute the sound heard on the TV, use the button . Pressing again turns the

sound on again.

4.3 Language settings for audio and subtitles and selection of option channels

4.3.1 Language for audio

1. Press to display the options bar.

2. Select Audio language using or and press or .

3. Select the language using or and press .

4.3.2 Language for subtitles

1. Press to display the options bar.

2. Select Subtitle language using or and press

or .

3. Select the language using or and press .

4.3.3 Selecting option channels

1. Press to display the options bar.

2. Select Video subchannel using or and press

or .

3. Select the language using or and press .

Note

All changes are immediately reflected in the program that you are watching. The temporary adjustments will be lost if you switch to another channel.

For a permanent change of language or settings for subtitles, press

on your remote and select Settings, System set-up, Language

(see chapter 7.2.1, Language).

Page 27

DCI85HD KD

4.4 Teletext

You can view teletext pages with additional information on television programs, if this service is supplied by the channel.

Press to open the teletext page for the channel you are watching.

To make teletext pages appear transparent so that you can track the current program in the background,

press again.

To scroll through the teletext pages, either select a page using the number buttons on your remote control or press the P+ or P- button on the remote control.

If the channel provides more screen options and services, select them using the color keys on the remote control.

To change back to the program from the teletext pages press and .

4.5 Listen to radio

The radio mode offers the same features as the TV mode.

Press on your remote to switch between TV mode and radio mode. On the TV screen the

selected channel and the current program are displayed.

If you press or one of the keys ,,, on the remote, the channel information is displayed as in

TV mode.

A Day of broadcast E Current and next program

B Channel number and name F Channel category

Title, start time and end time of the broadcast

G Choose category

D Elapsed time H Show options for this programn

HGF

C D

Page 28

DCI85HD KD

4.5.1 Selecting a radio channel

Press P+ or P- on the remote control to change channels or enter a channel number using the numeric keys on the remote.

Use the keys , to scroll through information regarding current and upcoming program.

Press or to display the radio channel list. As in TV mode, you may create a list of favorites among the radio channels (see chapter 7.5, Favorites).

4.5.2 Categories and other options in radio mode

Each time you change the radio channel the program information bar appears. If you press the yellow button on your remote now, you can quickly reach the first channel of a particular category, for example News where categories are available for the program.

Press to display detailed information about a program.

Press to see more options, if available for the current radio program.

Page 29

DCI85HD KD

5 Setting a timer

Your Receiver has the ability to set timers for favorite programs in order to notify you in time before the start of the broadcast. The unit will automatically switch to that program before the program starts.

This feature is especially useful when you wish to record a video or DVD. Before recording a program on video or DVD make sure that:

• Your recorder is connected to the Receiver (see chapter 2.4, Connection to the VCR / DVD recorder)

• Your recorder is adjusted for the same period for recording as the Receiver

• The Receiver is not turned off at the time of the recording but turned on or in standby mode.

You can record TV and radio programs.

5.1 Set timer

A flag can be set for upcoming broadcasts (TV and radio). To set a flag for a program, you have to navigate to the program information bar in the digital program guide or to the search results. Once you have set a flag (see below), you can change the channel or put the Receiver into standby. Shortly before the scheduled broadcast a screen message is displayed that the Receiver will switch to the remembered program.

By default, the Receiver switches to the respective program before the program begins. After the end of the program, the Receiver returns to the channel previously selected.

Note: If you want to record a flagged program on your VCR or DVD recorder, these devices must be set at the scheduled time to record.

5.1.1 Set flags in program information bar

1. Press or one of the keys , , , to enter the program information bar.

2. Use , to browse to the program you wish to record. Press to set a timer for a program. The

program information window opens.

3. Use , to select Set timer and press . See chapter 4.1.2, Program information bar for more

information.

5.1.2 Set timer in electronic program guide (EPG)

1. Press to switch to the EPG.

2. Use , , , to navigate to the selected program in the EPG. Press to set a timer for a

program. The program information window opens.

3. Use , to select Set timer and press . See chapter 6.1, Electronic Program Guide (EPG) for

more information.

Page 30

DCI85HD KD

5.1.3 Set timer in search results

1. Press to enter search, perform a search for keywords or categories as described

in chapter 6.2.

2. Use , , , to navigate to the selected program in the search results. Press to set a timer

for a program. The program information window opens.

3. Use , to select Set timer and press . See chapter 4.1.2, Program information bar for more

information.

• The selected program is marked in grey in the program information bar and in the EPG.

• If the saved program overlaps with another saved program, you will be prompted to correct the overlap.

If a program is not approved for minors, the Receiver asks you to enter the Parental Control PIN to confirm the timer.

5.1.4 Delete timer

1. In the program information bar, in the EPG or in search use the keys , , , to select a program.

2. Press . The program information window opens.

3. Use , to select Cancel timer and press .

5.2 Set timer manually

To set a timer for a program, the Receiver automatically retrieves the data required for the selected program and stores it.

If too few details for the program are available, the Receiver offers to set the details of the recording manually.

Additionally, you can also prepare a timer manually for a period of your choice on a channel you select.

Press on your remote and use the keys , and to choose Settings, Timer, Set timer.

Now choose your settings:

1. Choose a channel. Use , to select Channel. In the list use , to select a channel and confirm

Page 31

DCI85HD KD

your choice by pressing .

2. Select a date. Use , to select Date. Use the number keys of your remote to choose a date.

3. Enter the start and end time of the timer. Press , to select Start time. The marker automatically

jumps to the line End time. Use the number buttons on your remote to insert the end time.

4. Select whether the recording should take place once or repeatedly. The marker jumps automatically to

the line Repeat. By default Once is set. To set an automatic repetition of the recording, press . Now

select how often you want the recording to take place:

• Once: once at the set time.

• Daily: every day at the set time.

• Mon-Fri only: every week day from Monday to Friday at the set time.

• Weekly: at an interval of seven days from the date set for the set time.

5. Use , to select Save and press .

The manually prepared timers in the timer list will show a clock symbol. The manually prepared recurring timers are stored in a folder that is named with the channel's name and date and time of the recording.

Manual programmings can always be changed via the menu Timer.

5.3 Displaying and using timers

Press on your remote to open Timer. Or press and use and on your remote to

select Timer.

For details concerning your timers and folders choose the referring line using the keys , and press . All

timers are shown in Timer.

In Timer first all folders for series are displayed, followed by the timers created manually and the timers for individual programs. For each line, the following properties are displayed:

Note

You can customise your timer settings to add extra time before and after your manual timers (see chapter 7.4.2, Timer extensions).

Page 32

DCI85HD KD

• Folder or program name

• Start date of timer

• Time of broadcast

• Channel name or number

Use the following icons to quickly realize which kind of timers are displayed:

To leave Timer press .

Symbol Description

The folder contains timers with repetition scheme:

• A series whose future sequences are timed automatically.

• Manual timers with repetition scheme. The folder contains timers without repetition scheme:

• A series which is terminated.

• A series with deleted timers.

The timer was prepared manually.

The folder was prepared manually.

PIN protected timers. To lock / unlock an item select it using the

keys , , press and select an action.

Page 33

DCI85HD KD

6 Electronic program guide (EPG), search function

and Select Video (video library)

If you are looking for programs that interest you, press on your remote. Now you see the following options:

• Program Guide: The electronic program guide (EPG) provides an overview of current and upcoming

programs.

• Search: Searches current and upcoming programs by genre and titles that you enter.

• Select Video: Access to the online video Select Video to download a film or broadcast on your

Receiver.

6.1 Electronic Program Guide (EPG)

The digital program guide, also known as EPG, offers a preview for most TV and radio channels. You can set a timer directly from the EPG, see chapter 5.1.2, Set timer in electronic program guide (EPG). The EPG previews up to 7 days, depending on the channel.

Press on your remote control to open the EPG. Or press and select Program

Guide using the key and press on your remote control.

You can choose to view the digital program guide for the TV or the radio program. To switch between TV

and radio press on your remote.

You receive an information on the specific day that is displayed.

The period in which the programs are broadcasted. The current period is highlighted with a fine yellow timeline.

You receive an information on the specific channels that are displayed. If you select a channel, it is highlighted in yellow, the other channels are gray.

Here you can see the broadcasts of the respective channel (list on the left) for the relevant period (time axis above).

Page 34

DCI85HD KD

For better orientation, the EPG marks the current time with a yellow timeline.

How to use the EPG:

• To select a program or a channel on the current page of the digital program guide press the keys , ,

, on your remote. Looking for a specific channel and knowing the number of the channel in your favorites? Then you can also enter this number directly using the number buttons on your remote control.

• To browse the EPG, press P+ (one page forward) and P- (one page back) on your remote control.

• To move to the next day, press . To move to the previous day, press .

• To view details such as content or performer of a program, select the title of the program with one of

the keys , , , on your remote. As soon as the title of the program appears in yellow, press

• Do you want to leave the digital program guide and watch the program that you selected using the

keys , , , on your remote? Press .

• Do you want to see programs shown in prime time on the same day from 8 pm? Press .

• Do you want a preview exclusively for a particular channel category (e.g. sports)? Simply press the

yellow button on your remote control. Select a category using the keys , on your remote and

press .

• To set a timer for an upcoming program, select it by pressing the keys , , , and press .

For more information see chapter 5.1.2, Set timer in electronic program guide (EPG).

To exit the EPG press or on your remote.

6.2 Search

With the search function you can search for any keyword. For example actors, movie titles or different keywords but also by categories such as movies, series, entertainment, etc.

An internet connection is required for using all features within the search function. The results do not only include television broadcasts from the EPG but also the movies of online video library Select Video, if available in your region.

Press on your remote to begin the search.

You can also press on your remote control and then use the four keys , , , to select Search.

You are automatically in the keyword search.

6.2.1 Search by keyword

Enter a keyword on the on-screen keyboard:

• Select the characters using the four keys , , , and press for each character you want to

Page 35

DCI85HD KD

select.

After entering the third letter, the search will start automatically and search results that contain the letters you type.

The list on the right contains results that include your keyword. In the list you find results from the current television program and from the film supply of Select Video.

By pressing on your remote you can now switch to the right window into search results. If you want

detailed information about this result, use the keys , to select the search result and press . If you

selected a movie title with the arrow keys press . The time of the broadcast is displayed now. If your

keyword is an actor name, films with this actor will now display, including broadcast date and channel.

To select a TV program or a rental video from the list press and follow the instructions on the screen

navigating with the four keys , , , and confirming with .

Possibly the list of results has multiple pages. If necessary, move to the next page using and return to the last page pressing .

If you are in the keyword list, you may wish to refine your search. To do this, press to proceed to the search filters. The filters Search for keyword, Search for title only, Search for person only refine your search. In this case, the search only displays results according to the chosen filter. Use to move from the list of filters back to the refined search results.

6.2.2 Search by category

In addition, you also have the opportunitiy to search by category such as programs in a particular category (eg, movie or sport).

1. Select Category using , and press or .

2. Select a category from the list using , and press or .

3. For some categories more input is needed. E.g. if you select Spielfilm as category, another list is

displayed in which a subset should be selected, such as Action, Comedy, Krimi etc. Select a

subcategory from the list with the , keys and press .

4. If you want to refine your search, press to proceed to the search filters. Filters like Show all, Show

TV only refine your search. In this case only results according to the chosen filter are displayed. Select

a filter from the list with the , keys and press .

Note

You may enter numbers using on the on-screen keyboard as well as using the number buttons on your remote control.

Note

Possibly the list of categories has multiple pages. If necessary, move to the next page using P+ on your remote and return to the last page pressing P-.

Page 36

DCI85HD KD

6.2.3 Search results

In the list of search results all matching programs are displayed with date, time and channel.

How to use the search results:

• Browse the list of results using , on your remote.

• To browse several pages of a results list press P+ (one page forward) and P- (one page back) on your

remote.

• To display details like content or actors select the title of the program using the keys , , , . Is the

title marked yellow, press .

• To set a timer for a current program or prepare a timer, select it using , , , and press as

soon as the title is marked yellow.

For more information on this feature, see chapter 5, Setting a timer.

To leave the search press or on your remote.

6.2.4 Local Search

If you have not established an internet connection you can use the local search. Press on your

remote to start the search. You can also press on your remote control and then use the four keys , , , to select Search.

Press , select Search without internet connection and press .

6.2.4.1 Title/Actor

You can search for a program by entering the title or the actor name.

• On the Enter keyword tab, select at least three characters by using the four keys , , , and

the OK button on the virtual keyboard.

• Select the List entry on-screen to move to the list of keywords matching to the entered title/actor. If

there are no titles or actors listed, the list is disabled.

6.2.4.2 Categories

You can search for a program by category.

• Select Category and press OK or button.

Page 37

DCI85HD KD

• For some categories more input is needed. E.g. if you select Spielfilm as category, another list is

displayed in which a subset should be selected, such as Action, Comedy, Krimi etc.

• Press to view search results.

6.3 Select Video (online video library)

Select Video is a video-on-demand service (VOD). It offers videos on demand through the internet and in high diversity. You order and play rental videos via your Receiver, if it is connected to the internet.

6.3.1 Access to Select Video

Select Video is only available if the service is available in your region and you are entitled to. In addition, you have to connect the Receiver to the internet via your router in order to use all features of Select Video (see chapter 7.2.5, Internet).

6.3.2 Selection of videos

Press on your remote to enter the online video store. Alternatively press , select

Select Video using the key and press on your remote.

You will see a list of several categories such as Highlights, Specials, TV auf Abruf etc. Use the keys ,

to select a category and press .

Page 38

DCI85HD KD

You will now see the available films or programs in this category. Use the arrow keys to select a movie or

a show. Select a film or a program using , . If the item is marked yellow, press . Follow the

instructions on the screen. Navigate using , , , and confirm your selection with .

Page 39

DCI85HD KD

7 Settings

Press on your remote. Select Settings using the keys , . Press . Select one of the

following options using the keys , :

1. System update

2. System set-up

3. Parental control

4. Timer

5. Favorites

6. Service

7. System check

7.1 System Update

Using the settings in System update you can configure the software update feature, search for channels, add or remove channels, and reset the Receiver to factory default.

Press on your remote. Use the keys

to select Settings. Press . Select System

update with the keys

To return to the previous screen and save your changes, press or .

To exit the menu screen, press or .

7.1.1 Software update

You can choose two types of software updates, the two available options are Automatic and Manual. Manual is the default.

If Automatic is selected, the Receiver automatically updates its operating software at intervals when it is in standby mode. If Manual is selected, you will be prompted to perform the upgrade immediately when a software update is available, or wait until the Receiver is in standby mode or otherwise to refuse.

To change this setting:

1. Press on your remote. Use the keys

select Settings. Press .

2. Use the keys

to select System update. Press

or .

3. Use the keys

to select Software update mode. Press

or .

4. Use the keys

to select how the software should be updated: Automatic or Manual.

5. Press to confirm the new setting.

More information on software updates can be found in see chapter 8, Software update.

7.1.2 Search for updated software

You can search for new operating software for your Receiver at any time. This feature is especially useful

Page 40

DCI85HD KD

if you have previously rejected an update that you want to catch up now.

To start a search for new software:

1. Press on your remote. Use the keys

select Settings. Press .

2. Use the keys

to select System update. Press

or .

3. Use the keys

to select Search for new software.

Press or .

4. The Receiver will search for new software.

5. If new software is available, use the keys

to select one of the following options: Download it now,

In Standby or Do not download. Press .

More information on software updates can be found in see chapter 8, Software update.

7.1.3 Channel search

Per default the Receiver automatically checks at intervals if new channels are available, and stores them when it is in standby mode.

You can choose two types of channel search, the two available options are Automatic and Manual. Automatic is the default.

If Automatic is selected, the Receiver automatically updates its channels list at intervals when it is in standby mode. As soon as an update of the channel list is available you will be prompted to perform the update immediately, to wait until the Receiver is in standby mode or otherwise to refuse, if Manual is selected.

To change the setting:

1. Press on your remote. Use the keys

select Settings. Press .

2. Use the keys

to select System update. Press

or .

3. Use the keys

to select Channel scan mode. Press

or .

4. Use the keys

to select, how the channel list should be updated: Automatic or Manual.

5. Press to confirm the new setting.

Page 41

DCI85HD KD

7.1.4 Delete additional channels

Use this feature to delete unwanted channels after performing a manual search (described in chapter

7.1.5, Search additional channels).

1. Press on your remote. Use the keys

select Settings. Press .

2. Use the keys

to select System update. Press

or .

3. Use the keys

to select Delete additional channels.

Press or .

4. Use the keys

to select channels to be deleted and mark them. The list of additional channels may

consist of multiple pages. To browse through the pages of the list press P+ (forward) or Taste P- (back).

5. To undo the selection of a channel you selected press .

6. After selecting all channels to be deleted, press or .

7.1.5 Search additional channels

This menu lets you search for additional channels manually by typing a specific cable frequency. Cable frequencies are available on the website of Kabel Deutschland or made available by your television channel.

To start the search for additional channels:

1. Press on your remote. Use the keys

select Settings. Press .

2. Use the keys

to select System update. Press

or .

3. Use the keys

to select Search for additional

channels. Press or .

4. Input a Frequency using the number keys of your remote. Press .

5. Use the keys

to select Search. Press .

6. The Receiver searches for TV and radio channels and displays the number of channels found. To

cancel the search press or .

7. Save the channels by pressing .

7.1.6 Start a channel search

Per default the Receiver automatically checks at intervals if new channels are available and saves them when it is in standby mode. You can start this search manually, if necessary. This feature is especially useful if you have previously rejected an update that you want to catch up now.

Page 42

DCI85HD KD

To start a channel search:

1. Press on your remote. Use the keys

select Settings. Press .

2. Use the keys

to select System update. Press

or .

3. Use the keys

to select Automatic channel scan.

Press .

4. The Receiver will scan for new TV channels and radio channels and show the number of channels

found. You can stop the search by pressing or .

5. To save the channels press .

7.1.7 Reset to factory default

This menu lets you restore the factory settings of the Receiver.

1. Press on your remote. Use the keys

select Settings. Press .

2. Use the keys

to select System update. Press

or .

3. Use the keys

to select Factory reset. Press .

4. To cancel, use the keys

to select No. Press

or . To confirm, use the keys

to select Yes. Press .

5. After resetting to factory default, the installation screen of the Receiver is displayed. Set up the Receiver

again (see chapter 3, Initial installation).

7.1.8 Update EPG

You can update the electronic program guide if necessary.

To start the update:

1. Press on your remote. Use the keys

select Settings. Press .

2. Use the keys

to select System update. Press

or .

3. Use the keys

to select Program Guide refresh. Press

The message Program Guide refresh in progress… is displayed.

Note

If you restore the factory settings, your favorites, settings and prepared timer are lost.

Page 43

DCI85HD KD

7.2 System set-up

The System set-up menu allows you to change the settings for language, audio and picture, energy use as well as for the internet connection of the Receiver and to control the remote control app.

Press on your remote. Use the keys

to select Settings. Press . Use the keys

to select System set-up. Press .

To return to the previous screen to save your changes, press or .

To exit the menu screen, press or .

7.2.1 Language

Using this setting you can configure the language settings for the user interface and the subtitle of the program. Broadcasts are also shown in the selected menu language, if available. The automatic (permanent) subtitle display can be enabled or disabled here.

To open the language settings:

1. Press on your remote. Use the keys

select Settings. Press .

2. Use the keys

to select System set-up. Press

or .

3. Use the keys

to select Language. Press or .

7.2.1.1 Menu language

To set a default language for menus, sound and subtitles:

1. Use the keys

to select On Screen Language. Press

or .

2. Use the keys

to select a language.

3. Press to confirm.

7.2.1.2 Subtitles

To enable or disable automatic subtitle display:

1. Use the keys

to select Subtitles. Press or .

2. Use the keys

to select On (activate subtitles) or Off

(disable subtitles).

3. Press to confirm.

7.2.2 Audio

This menu lets you configure the following audio settings:

• Audio Output: Set the most appropriate AUDIO connector for your devices: Mono or Stereo.

• Dolby Digital on HDMI / Dolby Digital on SPDIF: You can activate or deactivate automatic playback

of Dolby Digital at the HDMI connection for digital video / audio and the DIGITAL AUDIO jack (S / PDIF). In this case broadcasts are delivered in Dolby Digital if available. Refer to the manual of your audio system, which settings your device requires.

Page 44

DCI85HD KD

• For visually impaired: This audio is supplement with the sounds that aid to understand the action on

the screen.

To open the audio settings:

1. Press on your remote. Use the keys

select Settings. Press .

2. Use the keys

to select System set-up. Press

or .

3. Use the keys

to select Audio. Press or .

7.2.2.1 Audio output

To set the default settings for the audio output:

1. Use the keys

to select Audio output. Press or .

2. Select the desired audio output. Use the keys

to select Mono or Stereo.

3. Press to confirm.

7.2.2.2 Dolby Digital

To enable or disable Dolby Digital replay at the HDMI connection for digital video / audio and at the DIGITAL AUDIO connector (S / PDIF):

1. Use the keys

to select Dolby Digital on HDMI or Dolby Digital on SPDIF. Press or .

2. Use the keys

to select On (enable Dolby Digital) or Off (disable Dolby Digital).

3. Press to confirm.

7.2.2.3 For visually impaired

To enable or disable audio for visually impaired:

1. Use the keys

to select Audio. Press or .

2. Use the keys

to select On (enable audio for visually impaired) or Off (disable audio for visually

impaired).

3. Press to confirm.

Page 45

DCI85HD KD

7.2.3 Picture

This menu lets you configure the following picture settings:

1. TV-SCART / VCR SCART

2. SCART Switching

3. HDMI Screen Resolution

4. Banner Timeout

5. OSD-Transparency

6. Start Channel

To open the image settings of the Receiver:

1. Press on your remote. Use the keys

select Settings. Press .

2. Use the keys

to select System set-up. Press

or .

3. Use the keys

to select Picture. Press or .

7.2.3.1 SCART settings for TV

Using this setting you can specify the most suitable video standard for TV output for the the TV connected to the TV SCART connector.

1. Use the keys

to select TV SCART. Press or .

2. Set the video standard that is best suited for your TV. Refer

to the manual of your TV for all necessary information. Use the keys

to select RGB, CVBS or S-Video.

3. Press to confirm.

7.2.3.2 SCART settings for video recorder or DVD recorder

This menu lets you adjust the video standard that is best suited for the VCR or DVD recorder connected to the VCR SCART output.

1. Use the keys

to select VCR SCART. Press or .

2. Set the video standard that is best suited for your device.

Refer to the manual of your video recorder or DVD recorder for all necessary information. Use the keys

to select

CVBS or S-Video.

3. Press to confirm.

Page 46

DCI85HD KD

7.2.3.3 Video aspect ratio for SCART

This menu lets you select whether the video aspect ratio (4:3 or 16:9) is also automatically displayed on the TV SCART output.

1. Use the keys

to select SCART-switching. Press

or .

2. Use the keys

to select Always 16:9 or Always 4:3.

3. Press to confirm.

7.2.3.4 HDMI video resolution

Using this setting you can specify the output resolution for HDTV.

1. Use the keys

to select HDMI screen resolution.

Press

or .

2. Determine the output resolution of your HD TV. Use the

keys

to select 576p, 576i, 720p or 1080i. If you use a

standard TV, leave the setting to 720p.

3. Press to confirm.

4. The Receiver will temporarily switch to the selected

resolution. If you do not want to save this setting, use the

keys

to select No, press and select a different setting. If you want to save this setting, use the

keys

to select Yes.

5. Press to confirm.

7.2.3.5 Display options for program information bar

Using this setting you can select how long the program information bar should be displayed on the TV screen (for more information see chapter 4.1.2, Program information bar).

1. Use the keys

to select Banner timeout. Press

or .

2. Use the keys

to select 5 sec or 10 sec.

3. Press to confirm.

7.2.3.6 OSD Transparency

Using this setting you can select how transparent menus and messages in the so-called On-Screen Display (OSD) on the TV screen will be displayed.

1. Use the keys

to select OSD transparency. Press

or .

2. Use the keys

to select None to disable OSD

transparency. Use the keys

to select 10%, 30% or

50%, if you want to soften the image in the background to the respective percentage.

3. Press to confirm.

Page 47

DCI85HD KD

7.2.3.7 Startup channel

Select On, if the Receiver should always show the Kabel Deutschland channel on startup. Select Off, if the Receiver should always show the last viewed channel on startup.

1. Use the keys

to select Start channel. Press

or .

2. Use the keys

to select Off, if the Receiver should

always show the last viewed channel on startup. Use the keys

to select On, if the Receiver should always show

the Kabel Deutschland channel on startup.

3. Press to confirm.

7.2.4 Energy settings

In this menu you decide whether your Receiver consumes less energy overall, but starts slowly, or if you wish a rapid operation of the Receiver, but want to take into account a higher overall energy consumption of the device. Select one of the modes: Standard, Energy Save Mode, Quick Start and Active. The default is the Standard mode, it causes the lowest power consumption and a longer start-up phase.

To change this setting:

1. Press on your remote. Use the keys

select Settings. Press .

2. Use the keys

to select System set-up. Press

or .

3. Use the keys

to select Energy settings. Press

or .

4. Use the keys

to select Standard, Energy Save Mode, Quick Start or Active. Press . A

description of the different modes is displayed.

Standard: This mode helps you minimize your energy consumption. For this reason your Receiver takes longer to start and switches off automatically if the remote control is not used. The duration until automatic switch-off can be determined.

1. Use the keys

to select Standard.

2. Press two times.

3. Use the keys

to select the time in hours, until the device turns off automaticcally and press .

4. Use the key to select Confirm and press .

Energy Save Mode: In the Energy Save Mode your Receiver consumes little energy on standby. In

contrast to the standard mode the Receiver does not switch off automatically.

1. Use the keys

to select Energy Save Mode.

2. Press two times.

Quick start: In the quick start mode you can set on which days, at what time and for how long your

Receiver automatically turns on from standby mode to active mode. The Receiver switches to active mode for the duration you determined.

1. Use the keys

to select Quick start.

2. Press

3. Enter a start time using the number keys of your remote, for example 1 7 0 0 for 17:00 hrs (=5 p.m.).

Page 48

DCI85HD KD

4. Press and use the keys

to select, for how many hours the Receiver remains in the Active

mode. Press .

5. Use the keys

to select Days. Press .

6. Use the keys

to select the days, on which the device remains in the Active mode during the time

selected before. Press for every day you wish to select.

7. Press to save your settings.

8. Use the keys

to select Confirm and press .

Active: In the Active Mode your Receiver is always available and boots within seconds. In this mode the device has the highest power consumption.

1. Use the keys

to select Active.

2. Press two times.

7.2.5 Internet

With an internet connection additional offers from Kabel Deutschland are available. To use them, you need to connect your Receiver to the internet, either through the wireless stick or via a network cable (LAN cable).

To set up an internet connection:

7.2.5.1 Setting up a wireless internet connection (Wi-fi)

1. Press on your remote. Use the keys

to select Settings. Press .

2. Use the keys

to select System set-up. Press or .

3. Use the keys

to select Internet. Press or .

4. Use the keys

to select Internet set-up. Press .

5. Use the keys

to select Via the Kabel Deutschland wireless LAN-Stick or Via a LAN-cable.

Press .

Using the Kabel Deutschland WLAN-Stick

1. Use the keys

to select Via the Kabel Deutschland wireless LAN-Stick. Press

Note

Make sure that you have either the wireless stick connected via a USB port OR a LAN cable to the network port on the Receiver (see chapter 2.2,

Connection to TV).

Note

If the network does not appear in the list, you must configure it manually (see section Setting up a wireless internet connection (Wi-fi) manually, page

47).

Page 49

DCI85HD KD

2. Use the keys

to select Continue with security key for wireless LAN or Continue with WPS.

You have additionally the option of selecting WPS. WPS stands for Wi-Fi Protected set-up and is another technology for establishing wireless connections, but with lower level safety.

Continue with wireless key

1. Use the keys

to select Continue with security key for wireless LAN. Press

2. The device now searches for available wireless networks. Use the keys

to select the wireless

network you would like to connect to. Press .

3. Enter your wireless key.

Now an on-screen keyboard is displayed to type the WLAN key. The wireless key is usually between 8 and 63 characters long and can consist of numbers, letters and special characters. Usually you have to distinguish between lowercase and uppercase letters. To enter the WLAN key, move the yellow highlight using the four keys , , , on your remote

control to the first character of the Wi-Fi key, and then press on your remote control. The character appears in the input line on the screen keyboard. Enter all characters of the wireless key. Use the ABC

field in the screen keyboard and press on your remote to set the lowercase letters shown in the screen keyboard to uppercase if necessary. Use the field !&? in on the on-screen keyboard and press

on your remote to display the special characters available. If the key is entered completely and

correctly, finish the input via the field Input ready on the on-screen keyboard and press on your remote control.

4. Now, the Receiver checks the network and internet connection. If the Receiver is connected to the

internet, the message The internet connection has been set up appears. In addition, the LED light flashes on the wireless stick in the color orange.

Continue with WPS

1. Use the keys

to select Continue with WPS. Press .

2. The device detects the internet connection and sets it up automatically. Press .

Setting up a wireless internet connection (Wi-fi) manually

Use the manual configuration if your wireless network (Wi-fi) is not visible for security reasons, but allows devices to detect and register. To perform the manual configuration, keep the following information about the network ready: SSID network name, wireless security type and wireless key.

1. Press on your remote. Use the keys

to select Settings. Press .

Note

The wireless key is a string in the form of a password that protects access to your wireless internet access from unauthorized third parties. The wireless key is usually found in the documentation of your wireless router, the wireless access point to the internet. It is strongly discouraged to operate a wireless internet access in Germany without protection by a wireless key for reasons of data protection, data security and for legal liability.

Note

For a WPS connection your router has to be prepared. The settings for a WPS connection have to be made in the software menu of your router. In addition, some routers ask for WPS activation on the router device itself.

Page 50

DCI85HD KD

2. Use the keys

to select System set-up. Press or .

3. Use the keys

to select Internet. Press or .

4. Use the keys

to select Internet set-up. Press .

5. Use the keys

to select Via the Kabel Deutschland wireless LAN-Stick. Press .

6. The screen for the network selection is displayed. Press to configure a wireless network (Wi-

fi) that is not visible for security reasons.

7. Use the keys

to select SSID. Press

8. Enter the name of the wireless network (also called SSID) on the on-screen keyboard.

To enter the SSID, move the yellow highlight using the four keys , , , on your remote control to

the first character of the SSID, and then press on your remote control. The character appears in the input line on the screen keyboard. Enter all characters of the wireless key. Use the ABC field in the

screen keyboard and press on your remote to set the lowercase letters shown in the screen

keyboard to uppercase if necessary. Use the field !&? in on the on-screen keyboard and press on

your remote to display the special characters available. If the key is entered completely and correctly, finish the input via the field Input ready on the on-screen keyboard and press on your remote

control.

9. Select Security Type. Press . Select the type of security used on the network (unsecured, WEP,

WPA-PSK or WPA2-PSK) using the keys , . Press .

10.Select Security Key. Press .

To enter the WLAN key, move the yellow highlight using the four keys , , , on your remote control

to the first character of the Wi-Fi key, and then press on your remote control. The character appears in the input line on the screen keyboard. Enter all characters of the wireless key. Use the ABC field in the

screen keyboard and press on your remote to set the lowercase letters shown in the screen keyboard

to uppercase if necessary. Use the field ! &? in on the on-screen keyboard and press on your remote

to display the special characters available. If the key is entered completely and correctly, finish the input via the field Input ready on the on-screen keyboard and press on your remote control.

11.Use the keys

to select Save. Press .

Setting up an internet connection via network cable (LAN cable)

1. Press on your remote. Use the keys

to select Settings. Press .

2. Use the keys

to select System set-up. Press or .

3. Use the keys

to select Internet. Press or .

4. Use the keys

to select Internet set-up. Press .

Page 51

DCI85HD KD

5. Use the keys

to select Via a LAN-cable. Press .

The device detects the internet connection and sets it up automatically. Press .

7.2.5.2 Show internet connection settings

With this menu you can view the internet settings of the device.

1. Press on your remote. Use the keys

to select Settings. Press .

2. Use the keys

to select System set-up. Press or .

3. Use the keys

to select Internet. Press or .

4. Use the keys

to select View settings. Now the settings of the internet connections are displayed.

7.2.5.3 Test internet connection

In this menu you can test your internet connection.

1. Press on your remote. Use the keys

to select Settings. Press .

2. Use the keys

to select System set-up. Press or .

3. Use the keys

to select Internet. Press or .

4. Use the keys

to select Test Connection. Press

5. The Receiver tests the connection and displays the result on the TV screen.

7.2.5.4 Disable internet connection

With this menu you can turn off the internet connection.

1. Press on your remote. Use the keys

to select Settings. Press .

2. Use the keys

to select System set-up. Press or .

3. Use the keys

to select Internet. Press or .

4. Use the keys

to select Switch off. Press

A message is displayed: If you switch off now

you will lose all functions using the internet connection. Most important examples are Video-onDemand (if available) and Keyword Search.

5. To turn off the connection press two times. To leave the connection turned on press .

7.2.5.5 Privacy

In this menu you can view the privacy information.

1. Press on your remote. Use the keys

to select Settings. Press .

2. Use the keys

to select System set-up. Press or .

3. Use the keys

to select Internet. Press or .

4. Use the keys

to select Data privacy. Press

5. The privacy policy is displayed. Use P+ and P- to browse. Press to leave this menu.

Page 52

DCI85HD KD

7.3 Protection of minors

With the Parental control menu you can change the PIN protection stored on your smartcard.

If you use the online video library Select Video, you can also:

• Change the Adult PIN

• Protect the purchase of Select Video with your Parental Control PIN

To return to the previous screen and save your changes, press or .

To exit the menu screen press or .

7.3.1 Change Parental Control PIN

The Parental Control PIN is used to block access to channels and broadcasts, which are not suitable for minors. If you switch to channels or programs that are subject to the protection of minors the Receiver asks you to enter the Parental Control PIN. The broadcast will be played back after the correct Parental Control PIN has been entered.

Please note if you change the Parental Control PIN:

• The Parental Control PIN is a four digit code.

• You must first enter the current Parental Control PIN before changing.

• The current Parental Control PIN must match the PIN stored on the smartcard.

• The new Parental Control PIN must be different from the current PIN.

• The new Parental Control PIN must be different from the current Adult PIN, both must not be the

same.

• The new PIN must not consist of the same four digits.

• If you enter the wrong PIN three times, access is blocked for ten minutes.

To change the Parental Control PIN:

1. Press on your remote. Use the keys

select Settings. Press .

2. Use the keys

to select Parental control. Press or

3. Use the keys

to select Change PIN. Press or .

4. Enter the current four-digit Parental Control PIN using the

number keys on the remote control.

5. Enter the new four-digit Parental Control PIN.

6. Enter the new four-digit Parental Control PIN again, to protect against typos. If the first and second input

match, you will receive confirmation that the Parental Control PIN has been changed successfully.

Page 53

DCI85HD KD

7.3.2 Change Adult PIN

The Adult PIN protects access to videos in the online video library Select Video, which are only suitable for adults. You can only change the Adult PIN if you use Select Video. Please note that the Adult PIN is always sent by mail and you may have to wait a few days until you can change the Adult PIN on your device.

Please note if you change the Adult PIN:

• The Adult PIN is a four digit code.

• You must first enter the current Adult PIN before changing.

• The current Adult PIN must match the Adult PIN stored.

• The new Adult PIN must be different from the current Adult PIN.

• The new Adult PIN must be different from the current Parental Control PIN, both must not be the

same.

• The new Adult PIN must not consist of the same four digits.

• If you enter the wrong PIN three times, access is blocked for ten minutes.

1. Press on your remote. Use the keys

select Settings. Press .

2. Use the keys

to select Parental control. Press or

3. Use the keys

to select Change PIN-18. Press or

4. Enter the current four-digit Adult PIN using the number keys on the remote control.

5. Enter the new four-digit Adult PIN.

6. Enter the new four-digit Adult PIN again, to protect against typos. If the first and second input match,

you will receive confirmation that the Adult PIN has been changed successfully.

7. Press to close the menu window.

7.3.3 PIN request when ordering Select Video

With this setting, you can protect the order of paid programs in the online video library Select Video by first entering the Parental Control PIN. If this is selected, the Receiver prompts you to enter the Parental Control PIN as soon as you order a video in the online video library Select Video.

To set up PIN protection:

Note

This function can only be used when the online video library Select Video is available at your address and if you are unlocked for the online video library Select Video.

Note

This function can only be used when the online video library Select Video is available at your address and if you are unlocked for the online video library Select Video.

Page 54

DCI85HD KD

1. Press on your remote. Use the keys

select Settings. Press .

2. Use the keys

to select Parental control. Press or

3. Use the keys

to select PIN VOD purchase. Press

or .

4. Use the keys

to select On (PIN protection activated) or Off (PIN protection deactivated). If you

select On, a window opens. Enter the current Parental Control PIN.

5. To turn off the Parental Control PIN protection, use the keys

to select Off. A window opens. Enter

the current Parental Control PIN.

7.3.4 PIN-protect timer

With this setting, you can protect access to your timer with the Parental Control PIN.

1. Press on your remote. Use the keys

to select Settings. Press .

2. Use the keys

to select Parental control. Press or .

3. Use the keys

to select PIN for timer. Press or .

4. Use the keys

to select On (PIN protection activated) or Off (PIN protection deactivated). If you

select On, a window opens. Enter the current Parental Control PIN.

5. To turn off the Parental Control PIN protection, use the keys

to select Off. A window opens. Enter

the current Parental Control PIN.

7.4 Timer settings

The menu Timer lets you prepare timers manually.

To return to the previous screen and to save your changes, press or .

To exit the menu screen, press or .

7.4.1 Manual timer

This menu lets you program timers manually.

1. Press on your remote. Use the keys

select Settings. Press .

2. Use the keys

to select Timer. Press or .

3. Use the keys

to select Set timer. Press or .

4. Set the timer options.

More information about timer functions can be found in chapter 5, Setting a timer.

Page 55

DCI85HD KD

7.4.2 Timer extensions

In this menu you can set timer extensions that are automatically added to recordings from the EPG. It allows you to set the Receiver in a way that the timer begins before the announced starting time and ends after the announced end time.

You can program the following setttings:

1. Press on your remote. Use the keys

select Settings. Press .

2. Use the keys

to select Timer. Press or .

3. Use the keys

to select Guard time. Press or .

4. Press to confirm the new setting.

7.5 Favorites

7.5.1 Add favorites

You can create two separate lists of favorites: for TV channels and radio channels.

1. Press on your remote. Use the keys

select Settings. Press .

2. Use the keys

to select Favorites. Press or .

3. Use the keys

to select Add. Press or .

Depending on the selected mode (radio or television), the list of TV channels or radio channels is displayed.

4. Press to specify which type of favorites list you want to create: TV channels or radio channels.

5. Select the channels you want to add as favorites. Use the keys

to select them. Press for every

channel you want to add. Selected channels are now marked.

6. To cancel your selection, press . To browse the list, press P+ or P-.

7. Press or . A confirmation message is displayed.

8. Press to save your favorites list.

Note

In our example, the timer will start 1 minute before the start time and end 14 minutes after the end time of the broadcast. To choose the correct entries:

• For Start time enter the number of minutes using the number buttons on

your remote control. Possible entries are all two-digit numbers from 00 to 99, e.g. 01.

• For End time enter the number of minutes using the number buttons on

your remote control. Possible entries are all two-digit numbers from 00 to 99, e.g. 14.

Page 56

DCI85HD KD

7.5.2 Delete favorites

1. Press on your remote. Use the keys

select Settings. Press .

2. Use the keys

to select Favorites. Press or .

3. Use the keys

to select Delete. Press or .

4. Press to select the type of list you want to edit: TV

or radio.

5. Select the channels you want to delete as favorites. Use the keys

to select them. Press for

every channel you want to delete. Selected channels are now marked.

6. To cancel your selection, press . To browse the list, press P+ or P-.

7. Press or . A confirmation message is displayed.

8. Press to save your changes.

7.5.3 Sort favorites

With this setting you may rearrange your list.

1. Press on your remote. Use the keys

select Settings. Press .

2. Use the keys

to select Favorites. Press or .

3. Use the keys

to select Rearrange. Press or .

4. .Press to select the type of list you want to edit: TV

or radio.

5. Select the channels you want to move. Use the keys

to select them.

6. Use the keys

to move a channel by one position. Use the keys P+ and P- to move a channel by

ten positions. If a channel is in the right position, press .

7. Repeat the procedure for each channel you want to move.

8. Press or . A confirmation message is displayed.

9. Press to save your changes.

Page 57

DCI85HD KD

7.6 Service

7.6.1 Support by phone

In this menu you find a support number if you need assistance.

1. Press on your remote. Use the keys

select Settings. Press .

2. Use the keys

to select Service. Press or .

3. Use the keys

to select Hotline list.

7.6.2 Service messages

Service messages are text messages that may be sent to you from the manufacturer. The menu Service messages gives you access to all the messages that have been sent to you, both read and unread.

1. Press on your remote. Use the keys

select Settings. Press .

2. Use the keys

to select Service. Press or .

3. Use the keys

to select Service messages. Press

or .

4. To scroll the list of messages, press P+ or P-.

5. Use the keys

to select a message. Press to read it.

6. To save a message, use the keys

to select Close. To delete a message, use the keys

select Delete.

7.7 System Check

The information in these menus are particularly important in cases when you need to contact your cable operator or any other technical service.

Below you find information about the Receiver and its software, smartcard information, as well as a diagnostic program for the operating parameters of the Receiver.

To return to the previous screen and to save your changes, press or .

To exit the menu screen, press or .

7.7.1 Device Info

This menu contains information on your Receiver.

1. Press on your remote. Use the keys

to select Settings. Press .

2. Use the keys

to select System check. Press or .

3. Use the keys

to select Device Info, to look up the information on the device.

Page 58

DCI85HD KD

7.7.2 Smartcard

This menu contains information on your smartcard. To retrieve and display this information, the smartcard must be inserted into the Receiver.

1. Press on your remote. Use the keys

to select Settings. Press .

2. Use the keys

to select System check. Press or .

3. Use the keys

to select Smartcard, to look up the information on the smartcard.

7.7.3 TV Signal

This menu contains information about your cable connection and provides an overview of the signal quality of cable frequencies.

1. Press on your remote. Use the keys

to select Settings. Press .

2. Use the keys

to select System check. Press or .

3. Use the keys

to select TV signal, to look up the information on the TV signal.

The following network information is displayed:

• Last channel scan: Date of the last channel scan.

• TV/radio channels: Number of stored TV channels and radio channels.

• Tuner parameter: Displays the frequency and the modulation of the current channel for each tuner.

• Signal level: Displays the signal quality for each tuner to the current channel.

• BER: Displays the bit error rate of the current channel.

• Network info: Name of the cable network.

7.7.4 VOD Signal

With this setting you can check the video-on-demand (VOD) connection.

1. Press on your remote. Use the keys

to select Settings. Press .

2. Use the keys

to select System check. Press or .

3. Use the keys

to select VOD signal, to look up the information on the VOD Signal.

7.7.5 HDMI

This menu contains information about a HD-TV connected to the Receiver via HDMI cable.

1. Press on your remote. Use the keys

to select Settings. Press .

2. Use the keys

to select System check. Press or .

3. Use the keys

to select HDMI, to look up the information on HD-TV.

7.7.6 TV picture

This menu contains information about the current TV screen format and SCART equipment.

1. Press on your remote. Use the keys

to select Settings. Press .

2. Use the keys

to select System check. Press or .

3. Use the keys

to select TV picture, to look up the information about the TV screen format and

SCART equipment.

7.7.7 Audio

This menu contains information about the audio settings.

Page 59

DCI85HD KD

1. Press on your remote. Use the keys

to select Settings. Press .

2. Use the keys

to select System check. Press or .

3. Use the keys

to select Audio, to look up the information about the audio settings.

7.7.8 Network settings

This menu contains information about the internet connection via Wi-fi or network cable.

1. Press on your remote. Use the keys

to select Settings. Press .

2. Use the keys

to select System check. Press or .

3. Use the keys

to select LAN / WLAN, to look up the information about the internet and network

settings.

7.7.9 Back channel

With this setting, you can check the back channel connection.

1. Press on your remote. Use the keys

to select Settings. Press .

2. Use the keys

to select System check. Press or .

3. Use the keys

to select Back channel,to look up the information about the return channel

connection.

4. Press to check the return channel. Now details are displayed.

7.7.10 Test IP Connection

With this setting you can check the speed of your internet connection.

1. Press on your remote. Use the keys

to select Settings. Press .

2. Use the keys

to select System check. Press or .

3. Use the keys

to select Test IP connection, to look up the information about the speed of your

internet connection.

4. . Press to check the speed of your internet connection. Now the speed of your internet connection

is displayed.

Page 60

DCI85HD KD

7.8 Settings overview

The following table shows an overview of the Settings menu and the default settings of the Receiver:

• Default settings are bold.

• Grey cells show that the sub menu prompts for an action, for editing or shows data that can not be

changed.

• The asterisk (*) shows that the (sub) menu is only available when the Select Video service is enabled

and if this service is available at your home port.

Menu Sub-menu(s) Default settings #

System update p. 37

Software update mode Automatic | Manual p. 37

Search for new software

p. 37

Channel scan mode Automatic | Manual p. 38

Delete additional channels

p. 39

Search for additional channels

p. 39

Automatic channel scan

p. 39

Factory reset

p. 40

Program guide refresh

p. 40

System set-up p. 41

Language p. 41

On-screen language Deutsch | English | Turkish | Russian

Subtitles On | Off

Audio p. 41

Audio output Mono | Stereo

Dolby Digital on HDMI On | Off

Dolby Digital on SPDIF On | Off

For visually impaired On | Off

Picture p. 43

TV SCART RGB | CVBS | S-Video

VCR SCART CVBS | S-Video

SCART switching Always 16/9 | Always 4/3

HDMI screen resolution

1080i | 720p

(if not detected on TV set) |

576p | 576i

Banner timeout 5 sec | 10 sec

OSD transparency None | 10% | 30% | 50%

Start channel On | Off

Page 61

DCI85HD KD

Energy saving mode On | Off p. 45

Standard

Energy save mode

Quick start

Active

Internet (*) p. 46

Internet set-up

View settings

Test connection

Switch off

Data privacy

Parental control p. 50

Change Parental Control PIN

Change Adult PIN PIN for VOD On | Off

Timer p. 52

Set timer

Guard time

Automatic | Manual

If set to Automatic:

• Start guard time: 1 min.

• End guard time: 14 min.

Favorites p. 53

Add

Delete

Rearrange

Service p. 55

Hotline list p. 55

Service messages p. 55

System check p. 55

Device Information p. 55

Menu Sub-menu(s) Default settings #

Page 62

DCI85HD KD

Manufacturer

Model

Serial number

CA Serial number

Hardware version

Software version

Last SW update

Last SW update status

Provisioning code

Free space

Smartcard p. 56

Smartcard serial No.

Smartcard version

Smartcard status

Program data status

Program data version

Program guide update

Status program guide

CA project name

CAK version

Chip NUID

TV signal p. 56

Last channel scan

TV channels

radio channels

Tuner parameter

Signal level

BER

Network

VOD signal p. 56

HDMI p. 56

Menu Sub-menu(s) Default settings #

Page 63

DCI85HD KD

HDMI screen resolution

HDMI status

HDCP status

TV manufacturer

TV model

TV picture p. 56

Selected channel

Picture mode

TV SCART

VCR SCART

SCART switching

Audio p. 56

On-screen language

Subtitles

Audio output

Dolby Digital on HDMI

Dolby Digital on SPDIF

For visually impaired

LAN / WLAN p. 57

WLAN / LAN IP address

Subnet mask

Default gateway

DNS server

LAN MAC address

Connection uptime

SSID

WLAN encryption

WLAN MAC address

Signal strength

Back channel p. 57

Test IP connection

p. 57

Menu Sub-menu(s) Default settings #

Page 64

DCI85HD KD

8 Software update

By default, the Receiver is in manual mode. The Receiver automatically checks for new software in the cable network. If an software update is available you can directly start the update, postpone until next standybode or reject.

Using the menu Settings, System update, Search for new software you can start an automatic search for new Receiver software at any time (see chapter 7.1.1, Software update). If you change the update settings, the Receiver asks if you wish to perform the upgrade immediately, wait for the next switch to standby mode or to reject it.

In manual mode, when a new software update is available an alert is displayed:

• To accept the update, use the keys , to select Yes (Upgrade now). Press .

The Receiver starts an update. You can use the Receiver only after successful completion of the update:

- The progress of the update is displayed in the status screen.

- After the update, the Receiver automatically switches back to the previously viewed program.

• To update in standby mode, use the keys , to select No (Wait for Standby). Press . The

Receiver will update the software next time it switches to standby mode.

• To reject the update, use the keys , to select No (Do not upgrade at all). Press . The

Receiver will not update the software.

Note

Please note, that you may not be able to use technical developments or additional services, if you reject a software update.

Page 65

DCI85HD KD

9 Universal remote control

The remote control is a universal model. You can program it to control your TV as well. The supported devices are listed in the Brand Code List.

After programing the remote use press to switch from Receiver mode to TV mode. The LED flashes once in short interval. The LED also flashes after each command is transmitted to the TV.

These are the main controls for the direct control of your television:

• Standby/Wake up

• Volume up / down, mute

• Changing channels, keys P+ and P-

• Four arrow keys , , , ,

• Access to the TV menu, key

Press to return to Receiver mode.

9.1 Programing the universal remote control

Refer to the brand code list for the right four-digit code for your TV.

1. Turn on your TV.

2. Press and at the same time for at least 3 seconds, until the LED on the remote

flashes two times.

3. Enter the 4-digit code for your TV or the universal code. Make sure that not more than 10 seconds pass

between the entry of each number. After entering the first 3 digits the LED flashes one time in short interval. After the fourth digit the LED flashes 2 times short and then remains lit.

4. Press until your TV turns off.

5. Release the key.

6. Press for 3 seconds to confirm the code.

7. Press to use your TV.

If you do not see your TV in the code list, please enter the code "0000" in step 3 and keep pressed

until your TV turns off. The remote control now starts a search through all the available codes. This process may take some time.

Page 66

DCI85HD KD

9.2 Selection of the volume control

When a TV code is programmed into the remote, the remote controls the volume of the TV also in

Receiver mode (instead of the Receiver's volume). To change, press and at the same time

for at least 3 seconds. The LED on your remote flashes 2 times.

To switch back to TV control mode, keep and pressed at the same time for at least 3

seconds. The LED on your remote flashes 2 times.

9.3 Reading out the 4-digit code

Using this method, you can read out the 4-digit code stored in the remote to control the TV.

1. Press the number key 1 and at the same time: The LED on your remote shows the first digit of

the code by flashing. E.g., if the first number is 9, the LED flashes 9 times. No flashing means 0 (zero).

2. Press the number key 2 and at the same time for the second digit of the code.

3. Press the number key 3 and at the same time for the third digit of the code.

4. Press the number key 4 and at the same time for the fourth digit of the code.

9.4 Reset the universal remote control

1. Press , and at the same time for at least 3 seconds. The LED on your remote

flashes 2 times.

2. All codes stored in the remote will be deleted. After restoring the factory settings on your remote, the

LED flashes twice again.

Page 67

DCI85HD KD

9.5 Brand Code List

TV Brand

Brand

code

TV code(s)

A.R. Systems 0583

Accent 0583 0064

Acec 0039

Acer 1366 1671, 2217, 1536, 1430

Acoustic Solutions 1694

Adcom 0652

Admiral 0120 0445, 0114, 0291

Advent 0903

AEG 0633

2123, 1399, 2048, 1064, 1583, 2193, 1582, 1190, 2266

Agef 0114

Aim 0064 0583

Aiwa 0728 0732, 1943, 1532

Akai 0388

0235, 0398, 0064, 0460, 0218, 1892, 1286, 1275, 1962, 2048, 2123, 1335, 0633, 0613, 1064, 0500, 0675, 0839, 0583, 0575, 0507, 0658, 0291, 0205, 0062, 0036, 0245, 0579, 0741, 0742

Akiba 0245 0064, 0583, 0321

Akura 1694 1672, 1797

Alkos 0062

Allorgan 0321

Allstar 0064 0583

Amoi 1556 2369

Amstrad 0036

0291, 0398, 0245, 0064, 0583, 0460, 1064, 0675, 2009, 1847

Anam National 0677

Andersson 1190 1612, 1176

Anglo 0036 0291

Anitech 0036 0291, 0064, 0583

Ansonic 0397

0064, 0583, 0036, 0695, 0438, 0274, 1464, 0039

AOC 1615 0652, 2138

Apollo 0500

Ardem 0513 0064, 0583

Arena 0064

Aristona 0583 0064, 0039

Art Mito 1612 1847

ASA 0132 0373, 0097, 0114

Asberg 0064 0583

Asora 0036

Astro 0667

Atec 1633

Atlantic 0064 0583

Atori 0036

Audiosonic 0064

0583, 0136, 0741, 0742, 0397, 0291, 0245, 0513, 2010

Audioton 0513 0397, 0291

Autovox 0114 0571, 0376, 0274

Avol 1847

Axxent 0036

B&D 1244

Baier 0903 1399, 2266

Bang & Olufsen 0592 0647, 0114, 1647

Barco 0579

Basic Line 0064 0695, 0583, 0036, 0245, 1064

Bauer 1642

Baur 0562

0222, 0539, 0064, 0583, 0581, 0218, 0388, 0571, 0376, 1532, 1037

Beaumark 0205

Beko 0741

0513, 0742, 0064, 0633, 1679, 2227, 1827, 0397, 0835

Bennett 0583 0064

BenQ 1589 1601

Beon 0064 0583, 0445

Best 0397 0448

Bestar 0064 0583, 0397

Black Diamond 1064 0583, 1190

Blackway 0245

Blaupunkt 0581

0222, 0562, 0218, 0227, 0354, 0197

Blue Media 1633

Blue Sky 0064

1064, 0741, 0514, 0695, 0742, 0835, 1390, 1341, 1943, 1270, 0652, 1679, 0651, 1936, 0583, 0245

Boman 1399

Bondstec 0274

Boots 0036

Bosch 0354

BPL 0064 0583

Brandt 0652

0136, 0223, 0314, 0362, 0498, 0370, 0587

Brandt Electronique

0314 0362

Brinkmann 0064 0583, 0695, 0546, 0445, 0513

Brother 0291

Bruns 0114 0513

BSR 0321 0579, 0388

BTC 0245

TV Brand

Brand

code

TV code(s)

Page 68

DCI85HD KD

Bush 1064

1679, 0741, 1943, 0695, 1672, 0546, 1694, 0064, 0583, 1736, 1335, 0805, 0614, 1286, 2154, 0688, 1583, 0514, 1176, 1353

Canton 0245

Capsonic 0291

Carad 0637 0064, 0583, 0695, 1064

Carrefour 0097 0064, 0583

Cascade 0036 0064, 0583

Casio 0064 0583, 0376

CAT 1709 2182

Cathay 0064 0583

Centrum 1064

Centurion 0064 0583

Century 0114 0274

CGE 0101 0445, 0274, 0579, 0397

Cimline 0036 0262, 0245

Cinex 1583 0675

City 0036

Clarivox 0445 0064, 0583, 0097

Clatronic 1399

0633, 0245, 0064, 0583, 0741, 1704, 0036, 0398, 0675, 0397, 0274, 0291, 1190

Clayton 1064

Concorde 0036

Condor 0036

0397, 0438, 0445, 0064, 0274, 0291

Conia 1672

Conrac 0835

Conrad 0064 0583

Contec 0036 0038, 0291, 0064, 0583

Continental Edison

0136 0223, 0314, 0514

Cosmel 0036 0064, 0583

Crosley 0114 0274, 0101, 0579

Crown 0064

0513, 0633, 1064, 0742, 0514, 0235, 0445, 0397, 0741, 0036, 1679, 0695, 0448, 0680

CS Electronics 0245 0274

CTC 0274

Cybertron 0245

Cytronix 1325

D.Boss 1501 0064

Daewoo 0661

0688, 0526, 1936, 1822, 0064, 0651, 2302, 0741, 0583, 0036, 0907, 1334, 0903, 0892, 1639, 0245, 1164, 2064

Dainichi 0245

TV Brand

Brand

code

TV code(s)

Dantax 0397 0513, 0741, 0633, 0742

Daytek 1403

Daytron 0036 0064, 0583

de Graaf 0235 0575

Dell 1430

Denver 1704

1216, 2077, 0614, 2123, 2048, 1661, 1872, 2272, 0064, 2015, 1736, 1847

Desmet 0064 0583, 0036, 0114

Diamant 0064 0583

DiBoss 0064 0583, 1501

Digatron 0064 0583

Digihome 1694

Digiline 0064 0583, 0132, 0695

Digimate 0917

Digital Device 1633

Digitek 1736

Digivision 0388

DigiX 0907

DiK 0064 0583

Dixi 0036 0064, 0583, 0274, 0114

DMTECH 2028 1991

Domland 0421

Doric 0376

Dream Vision 1731 1781

DTS 0036

Dual 1064

2268, 0064, 1229, 0546, 0579, 1264, 1164, 0571, 0805, 0421, 1294, 0376, 0370, 1399, 1190, 0658, 1176, 2059, 0379

Dumont 0114 0097

Dunai 0571

Durabrand 0064 1464, 0583, 2015, 1679

D-Vision 2009 0064, 0583

Dynatron 0064 0583, 0039

e:max 1399 1558

Edison-Minerva 0514

Electrion 1612

Elekta 0036 0064, 0583, 0291

ELG 0064 0583

Elin 0064

0583, 0132, 0575, 0388, 0376, 0036

Elite 0245 0064, 0583

Elta 0036 0291

Emco 0274

Emerson 0114

0274, 1936, 0513, 0397, 0695, 0064, 0583, 0398, 0097, 0388, 0651

Emprex 1816

TV Brand

Brand

code

TV code(s)

Page 69

DCI85HD KD

Epson 0858

Erres 0064 0583, 0039

ESC 0064 0583

Estèle 0579

Etron 0064 0583, 0036

Eurofeel 0291

EuroLine 0064 2077

Euroman 0291 0064, 0583, 0448, 0397

Europa 0064 0583

Europhon 0064 0583, 0274, 0579

Evesham 1694

Exquisit 0064 0583, 0274

Fast 1928

Fenner 0036

Finlux 1694

0064, 0583, 1583, 2009, 1612, 1398, 0132, 1275, 0373, 0741, 0835, 0658, 0519, 0507, 0500, 0445, 0579, 0742, 0097, 0114, 0438

Firstline 0064

0583, 0695, 0741, 0651, 0036, 1390, 1190, 1398, 1639, 1335, 0376, 0262, 0235, 0388, 1064, 0835, 0321, 0274, 0579, 1936, 0438, 0571

Fisher 0235

0397, 0114, 0388, 0579, 0571, 0376

Force 1176

Formenti 0064 0583, 0513, 0114, 0579

Formenti-Phoenix 0579

Fortress 0120 0114

Fraba 0064 0583, 0397

Friac 0036

0064, 0583, 0448, 0397, 0526, 0682, 0637

Frontech 0274 0291, 0376, 0036

Fujitsu 0036 0379, 0064, 0583, 0388

Fujitsu General 0036

Fujitsu Siemens 1693

1325, 0835, 2201, 1275, 1190, 1286

Funai 1844

1421, 1064, 1693, 1622, 0695, 0741, 0291, 0321

Future 0064 0583

Galaxi 0064 0583, 0388

Galaxis 0397 0064, 0445, 0583

Galeria 0036

GBC 0579 0036, 0245

GE 0370

GEC 0388 0376, 0064, 0583

Geloso 0274 0036, 0579

General Electric 0370 0314

General Technic 0036

TV Brand

Brand

code

TV code(s)

Genexxa 0245 0064, 0583, 0036

Gericom 1244

1633, 0892, 1325, 1233, 0907, 0835, 1748

Goldfunk 0695

GoldStar 0064

0583, 0274, 0388, 0741, 0633, 0036, 0136, 0742, 0397

Gooding 0514

Goodmans 1286 1275, 1822

Gorenje 0397 0448

GPM 0245

Graetz 0388 0398, 1190

Gran Prix 0675

Grundig 0222

1250, 0562, 0097, 1609, 0581, 0064, 0218, 0561, 2227, 1286, 1827, 0205, 0583, 1064, 1694, 0784, 1403, 0470, 1335, 2266, 2152, 0514, 2154, 1962, 1943, 0397, 0036, 0614, 0370

H&B 0835 2028

Haier 1642

Halifax 0291

Hanimex 0245

Hanns.G 1640

Hannspree 2054 2245, 1640, 1378, 2241

Hanseatic 0546

0064, 0661, 2028, 0526, 0688, 0652, 0421, 0741, 1991, 0835, 0388, 0513, 0583, 0036, 0571, 0321, 0114, 0376, 0397

Hantarex 0036 0064, 0583

Hantor 0064 0583

Harsper 0892

Harwa 1223 1534, 1296

Hauppauge 0064 0583

HB 1399

HCM 0036 0064, 0583, 0245, 0445, 0291

Hedzon 0583 0064

Hema 0036

Highline 0291 0064, 0583

Hisense 1390 2125, 2064, 1341

Hitachi 1603

0508, 0605, 1799, 1064, 2234, 0526, 0771, 0064, 1072, 1511, 1221, 0252, 1508, 2241, 1881, 0388, 0661, 0746, 1190, 1612, 1176, 0824, 2154, 0507, 0904, 0519, 1164, 0575, 0376, 0500, 0911, 1694, 0579, 0223, 0370, 0136, 0132, 0205

Hitachi Fujian 0135 0252

TV Brand

Brand

code

TV code(s)

Page 70

DCI85HD KD

HMV 0114

Höher 0741 1583, 0892, 1190

Hugoson 1693

Humax 1566 1322, 1848, 1562

Hyper 0036 0274

Hypersonic 0388

Hypson 0064

0583, 0741, 0742, 0291, 1064, 0695, 0513

Hyundai 1308

1495, 1179, 0903, 1559, 1403, 0892, 1321, 1501, 1583, 1633, 0805, 1639

Iberia 0064 0583

ICE 0398 0245, 0291, 0064, 0036

Ices 0245

Ict 0064 1164, 0583

IISonic 1403

Iiyama 0904 0917, 2281, 1244

Ikasu 1704

Imperial 0445

0579, 0274, 0101, 0223, 0397, 0064, 0376

Indiana 0064 0583

InFocus 1457 1233

Ingelen 0514 0637, 0741, 0388, 1464

Ingersoll 0036

Inno Hit 0036

0064, 0583, 0245, 0274, 1190, 1612

Innovation 0546 0064, 0583

Innowert 0892 1325

Interactive 0064

0583, 0039, 0114, 0539, 0354, 0388, 0397, 0136, 0438

Interbuy 0036 0064, 0291, 0274, 0539, 0583

Interfunk 0064

0583, 0039, 0114, 0539, 0354, 0388, 0397, 0136, 0376, 0274, 0227

Internal 0064 0583, 0651, 0526, 1936

Intervision 0064

0398, 0546, 0513, 0397, 0421, 0514, 0245, 0291, 0274, 0036, 0583

Isukai 0245 0064, 0583

ITC 0579

ITS 0064 0398, 0245, 0291, 0036, 0583

ITT 2152

0575, 0388, 0507, 0376, 0500, 0373, 0235, 0613, 0637

ITT Nokia 0388

0575, 0500, 0507, 0376, 0373, 0235, 0613, 0633, 0637, 0658

ITV 0291

Jean 1540

JEC 0062

JGC 1704 1736

Jubilee 0583

TV Brand

Brand

code

TV code(s)

JVC 0680

1845, 1680, 0398, 2145, 0633, 0758, 0120, 0245, 0677, 0445

Kapsch 0388

Karcher 0633

1583, 0448, 0805, 0064, 0637, 0741, 0397, 0583, 0291, 2152, 1335, 2009

Kathrein 0583 0064, 0907

Kawa 0398

Kendo 1612

1064, 0637, 0438, 1176, 0397, 0064, 1464, 0513, 0675, 0274, 0546, 0262, 1164

Kennedy 0579

Kiton 0583 0064, 0695

Kobra 1325

Kolster 0064 0583, 0376, 0274, 0245

Konka 0064

0583, 0398, 0741, 0445, 0245, 2056

Kontakt 0514

Korpel 0064 0583

Korting 0114 0448, 0397

Kotron 0291

Koyoda 0036

Kriesler 0039

Kuba 0376

Kuba Electronic 0376

Kyoshu 0445 0291

L&S Electronic 0892 0741

LaSAT 0513 0397

Lava 1501

Leader 0036

Lemair 0438

Lenco 0064

0036, 1822, 0583, 0614, 1064, 2010

Lentec 1558

Lesa 0274

Levis Austria 0064 0583

Lexsor 1223 1534

Leyco 0291 0064, 0583, 0321

LG 1450

2209, 0205, 1869, 0741, 1690, 1867, 0064, 1332, 1664, 1748, 0583, 1566, 0742, 0136, 0274, 0388, 0397, 0036

Liesenkötter 0064 0354, 0039, 0583

Lifetec 0064

0695, 1064, 1164, 0546, 2028, 0245, 0036, 0741, 0682, 1275, 1286, 0291

Loewe 0539

0660, 1911, 0817, 1863, 0114, 1817, 0682, 0397

TV Brand

Brand

code

TV code(s)

Page 71

DCI85HD KD

Logik 0038

0398, 0907, 1244, 1064, 2056, 1672

Logix 0695 0546

Luma 0064 0438, 0583, 0036

Lumatron 0064 0583, 0388, 0291

Luxor 0507

0519, 0376, 0388, 0235, 0575, 0373, 0500, 1064, 0658

Madison 0064 0583

Magnavox 0064 0583

Magnum 0675 0741, 0064, 0742, 1316

Mandor 0291

Manesth 0064 0583, 0262, 0291, 0062, 0321

Manhattan 0064 0583, 0695, 1064, 0805

Maqma 1816 1633, 1325, 1729, 1736

Marantz 0064 0583, 1559

Mark 0064 0583, 0036, 0741, 0742

Master's 0526 0064

Masuda 0398

Matsui 1190

Matsushita 0677

Maxim 2009 1583

Medialine 1233 1991

Mediator 0064 0583, 0039

Medion 0835

1275, 0741, 1768, 0583, 1176, 1229, 1583, 0064, 0907, 1064, 1612, 1694, 0272, 1164, 1464, 0695, 1943, 2028, 0539, 1248, 1233

Megas 0637

MEI 1064 0064, 0583

Melectronic 0373

0064, 0539, 0136, 0370, 0274, 0222, 0688, 0741, 1679, 0314, 0583, 0651, 0661, 0388, 0218, 0132, 0036, 0507, 0519, 0438, 0376

Memorex 0036

Memphis 0036

Mercury 0064 0036, 0583

Metz 0474

1560, 0773, 0394, 0415, 1190, 0695, 0114, 0064, 0222, 0562, 0561, 0581, 0218

Micromaxx 1399

0741, 0064, 0695, 0835, 1064, 2028

Microstar 0835

Minato 0064 0583

Minerva 0514

1275, 0581, 0562, 0222, 0097, 0561, 0218, 0135

Minoka 0064 0583

Mirai 1693 2099, 1879

Mitsubishi 0135

0064, 0562, 0539, 1064, 0583, 0114, 0235

TV Brand

Brand

code

TV code(s)

Mivar 0397

Monaco 0036

Morgan's 0064 0583

MTC 0397 0376, 0539, 0388

MTlogic 1335

Multitec 0695

1064, 1583, 2009, 0064, 0583, 0513

Multitech 0376

0036, 0513, 0064, 0397, 0583, 0274, 0291, 0579

Musikland 0064 0245, 0274, 0583

Mx Onda 1672 1847

Myryad 0583 0064

NAD 0892

Naiko 0064 0633, 0583

Nakimura 0064 0583

NEC 2171

0197, 0272, 1731, 0036, 0064, 0038, 0526, 0688, 0732, 0731, 0680

Neckermann 0064

0218, 0397, 1532, 1037, 0561, 0376, 0114, 0274, 0438, 0539, 0227, 0581, 0583, 0579, 0354, 0445

NEI 0064 0583, 0398, 1064

Neon 1759

Neovia 1233 0892, 1991, 1398, 0903, 1403

Nesco 0274

Netway 2136

Neufunk 0064 0036, 0583, 0637, 0245, 0741

New Tech 0064 0036, 0583, 0370

Nikkai 1704

Nikkei 0741

Nobliko 0097

Nokia 0500

0507, 0388, 0613, 0575, 0658, 0633, 0376, 0373, 0235, 0519, 0637, 0136

Nordmende 1440

0136, 0587, 2358, 2356, 0314, 1316, 0498, 2359, 0223, 0741, 0362, 0370, 1612, 2034, 2028, 1694, 1286, 0064, 0222

Normerel 0064 0583

Novak 0039 0064, 0583

Novatronic 0064 0132, 0583

Novita 1612

Nurnberg 0388

Oceanic 0388

0321, 0235, 0500, 0575, 0507, 2028

Odeon 0291

Odys 2416 1822

Okano 0291 0036, 0397, 0064, 0583

Olidata 1403

TV Brand

Brand

code

TV code(s)

Page 72

DCI85HD KD

Omega 0291

Onwa 0398 0245, 0460

Optoma 1781 1701

Orbit 0064 0583

Orion 2034

2032, 0470, 0741, 0262, 0682, 0064, 2135, 0321, 0583, 2027, 0907, 0382, 1943, 1223, 0571, 0291, 0038, 0036

Orline 0064 0245, 0583

Ormond 0695 1064, 0064, 0583

Osio 0064 0583

Oso 0245

Osume 0245 0064, 0583

OTIC 1672 2010

Otto Versand 1532

1037, 0120, 0539, 0064, 0583, 0274, 0036, 0370, 0546, 0579, 0218, 0388, 0262, 0136, 0321, 0253, 0561, 0562, 0222, 0571, 0376, 0581

Pacific 0064

0583, 1164, 1264, 0741, 1064, 0470, 1399

Palladium 0397

0438, 0376, 0682, 0741, 0546, 0064, 0445, 0218, 1532, 1164, 0561, 0227, 0581, 0354, 0114, 0274, 0579, 0583, 1037, 2009

Panama 0036 0291, 0064, 0583, 0274

Panasonic 0677

1663, 1677, 0253, 1337, 1362, 0575, 0394, 0388, 0064, 0561

Papouw 0064 0583

Pathe Cinema 0376 0579, 0397

Pathe Marconi 0136 0223

Pausa 0036

Perdio 0064 0583

Perfekt 0064 0583

Philco 0114

0101, 0445, 0274, 0579, 0397, 0064, 0583, 0546

Philips 0583

1533, 0064, 1771, 0666, 1894, 0632, 1610, 1522, 2042, 1273, 1482, 0039, 0799, 0581, 0036, 0388, 0227, 0114, 0370

Phocus 1335 0741, 1316, 1679, 1827

Phoenix 0064 0583, 0397, 0513, 0114, 0579

Phonola 0064 0583, 0039, 0114

Pioneer 1484

1287, 0706, 0193, 0787, 0064, 0388, 0136, 0513, 0539, 0397, 0370, 0314

Pionier 0397 0513

Plantron 0583 0291, 0036, 0064

TV Brand

Brand

code

TV code(s)

Playsonic 0741 0064, 0742, 1827, 1679

Polaroid 1768 2152, 1672, 1550, 1747

Policom 0136

0223, 0388, 0097, 0101, 0114, 0562

Poppy 0036

Portland 0651 1936

Powerpoint 0514 0064, 0583, 1797

Prandoni-Prince 0274 0388

Prima 0036 0291, 1296, 1534, 1223

Prinz 0571 0376, 0388

Profex 0036 0388

Profi 0036

Profilo 1583

Profitronic 0064 0583

Proline 0064

0583, 0652, 0661, 0438, 0039, 1403, 1540, 1064

Prosonic 0695

0741, 1759, 2117, 2272, 0064, 0583, 0397, 0398

Protech 0064

0583, 0036, 0274, 0376, 0291, 0445, 0695, 0579, 0513, 1064

Proview 1672

Provision 1064 1558, 0064, 0583, 0741, 1399

Pye 0064 0583, 0039, 0114, 0581, 0376

Pymi 0036

QONIX 1661

Quadral 0245

Quasar 0274 0892, 0036

Quelle 0064

1532, 1037, 0038, 0136, 0539, 0373, 0448, 0579, 0036, 0583, 0222, 0227, 0291, 1064, 0321, 0274, 0101, 0354, 0097, 0132, 0695, 0562, 0571, 0376, 0581, 0218, 0388

radiola 0064 0583, 0039

radiomarelli 0114 0274, 0064, 0583

radioShack 0064 0583

radiotone 0695

0675, 0064, 0036, 1064, 0397, 0445, 0291

Rank 0097

RBM 0097

Recor 0064 0583

Rectiligne 0064 0583

Red Star 1583

Rediffusion 0388 0575, 0373

Redstar 0064 0583

REEL Multimedia 1451

Reflex 0064 0583, 1064, 0695

Relisys 1768

1672, 0904, 1233, 1325, 1403, 1612, 1639, 0892, 0903

TV Brand

Brand

code

TV code(s)

Page 73

DCI85HD KD

Revox 0064 0835, 0583, 0397

Rex 0438 0274, 0291

RFT 0291 0114, 0397, 0064, 0583, 0513

Ricoh 0064 0583

Roadstar 1064

0742, 0741, 0036, 0064, 1216, 1582, 1353, 0583, 0445, 0695, 1464, 0245, 0291, 1943

Robotron 0114

Rowa 0583 0291, 0036, 0614, 0064

Royal Lux 0448 0397, 0362

Rukopir 0583 0064

Saba 0652

0362, 0136, 0587, 0370, 0114, 0223, 0498, 0314, 1064, 0388, 0575, 0525, 1615, 0741, 0583

Sagem 0637 0857, 1340, 0645

SaiVOD 0064 0583, 0695, 1064

Salora 0376

0388, 0575, 0235, 0579, 0507, 2152, 1264, 0658, 1583, 0805, 1398, 1229

Salsa 0362

Samsung 2078

0839, 1485, 0645, 1339, 0614, 2164, 1276, 1657, 1705, 2121, 0671, 0583, 1262, 0064, 0036, 0793, 1659, 0397, 0546, 0291

Sansui 0064 0583, 0398, 1962

Santon 0036

Sanyo 0235

1235, 1674, 1612, 0036, 1694, 0571, 1676, 1064, 1675, 0135, 0197, 0731, 0397, 0038

Save 0064 0583

SBR 0064 0583, 0039

Schaub Lorenz 0741

2127, 1399, 0513, 0575, 0633, 1398, 0388, 1221, 0376, 2152, 1694, 1390

Schneider 0583

1164, 0064, 1064, 2155, 1644, 0695, 0546, 0379, 0039, 0571, 1501, 0376, 1395, 0274, 0741, 1399, 2009, 0421, 1264, 0398, 0388, 0245, 0370, 1943, 0097, 0675

Scott 1216 2010

Seaway 0661

SEG 1064

0695, 1190, 0064, 1176, 1936, 1464, 0651, 0579, 0583, 1928, 1612, 1694, 0036, 2088, 0514, 0661, 0291, 0245, 0376, 0274

SEI 0114

1532, 1037, 0579, 0571, 0376, 0321, 0064, 0583

TV Brand

Brand

code

TV code(s)

Sei-Sinudyne 0321

1532, 1037, 0579, 0571, 0064, 0583, 0114

Seleco 0438 0398, 0291, 0373

Sencora 0036

Sentra 0062 0245, 0036, 0376

Sharp 1686

0120, 1220, 1420, 1614, 2241, 1846, 1613, 0321, 0227, 0680

Shintoshi 0064 0583

Shivaki 0064 0583, 0470, 0205

Siarem 0579 0114

Siemens 0222

0581, 0218, 0562, 0227, 0354, 0064, 0561, 0583, 0388

Siera 0064 0583, 0039, 0614

Siesta 0397

Silva 0388 0675, 0064, 0583

Silva Schneider 1583 2193, 0675, 2152

Silver 0388 0742

Simz 1847

Singer 0036 0114, 0064, 0583, 0274, 0362

Sinudyne 1399

0114, 0262, 0321, 0579, 0388, 0633, 0571, 0376, 1532, 1037, 0064, 0583

Sky 1540

1640, 1633, 1772, 0688, 0892, 0907, 0205, 1531, 1642, 1403

Skymaster 0132

Sliding 0892 0907, 1399, 1395

Smaragd 0514

Soemtron 0892 1325

Sogo 1403

Solavox 0388 0575, 0064, 0583

Sonawa 0245

Soniko 0064 0583

Sonitron 0235 0397

Sonoko 0064 0583, 0036, 0291

Sontec 0064 0583, 0397, 0321, 0036

Sony 1852

1532, 1678, 1778, 1037, 0038, 1712, 0861, 0064, 0120, 0197, 0101

Sound & Vision 0245 0064, 0583

Soundwave 0064 0583, 0445, 0742

Standard 0064 0583, 1064, 0245, 0036

Starion 1064

Starlite 0036 0579, 0064, 0583, 0291

Starmedia 2136

Stenway 0245

Stern 0291 0438

Strato 0064 0583, 0291, 0036

Strong 0064 0583, 1190, 1176, 1064

TV Brand

Brand

code

TV code(s)

Page 74

DCI85HD KD

Sungoo 2064

Sunic Line 0064 0583

Sunstar 0398 0064, 0583, 0036, 0291

Sunstech 2028 1991

Sunwood 0036 0064, 0583

SuperTech 0036 0064, 0583, 0245

Supra 0036

Susumu 0362 0245, 0314

Sutron 0036

Swedx 1633

Swissline 0274

Swisstec 1531

Sysline 0064 0583

T+A 0474

Tandberg 0394 0438, 0136, 0223, 0388

Tandy 0245 0274, 0120

Targa 0645 2272, 1398, 1294

Tatung 1747

1275, 0064, 0583, 1399, 1286, 1583, 1398, 0038

TCM 2028 1335, 0741, 1316, 0835

TEC 0036

0274, 0498, 0362, 0579, 0064, 0583, 0388

Tech Line 0064 0583, 0695, 1464, 1190

Tech Lux 1216

Technica 2009

TechniSat 1294 0667, 0064, 2182, 0583, 0682

Technisson 0741 1316, 1679

Technotrend 1729 2182, 1558

Techvision 1736 1558

Techwood 1190 1064, 1694

Teco 1340 2136, 1550

Tedelex 0633 0064, 0036, 0235, 0614, 0583

Teiron 0036

Telefunken 0289

0652, 0498, 0128, 0362, 0136, 0314, 0525, 0370, 0587, 0101, 0064, 0513, 0741, 1583, 0373, 0223

Telefusion 0064 0583

Telemeister 0064 0583

Telesonic 0064 0583

Telestar 2345 0064, 2117, 0583

Teletech 0064 0695, 1064, 0036, 0274

Teleton 0376

Televideon 0579

Teleview 0064 0583

Tensai 0245

0064, 0583, 0321, 0036, 0132, 0398, 0274, 0742, 1064

Tenson 0036

Tesla 0064

TV Brand

Brand

code

TV code(s)

Tevion 1275

1164, 0741, 0583, 1583, 1064, 2050, 0695, 0835, 1768, 0675, 2268, 1316, 1827, 2117, 1612, 0892, 1286, 0064

Texet 0036 0245

Thomson 0652

0587, 0314, 0370, 0362, 0498, 0136, 1615, 0223, 2155, 0064, 0376, 0579

Thorn 0135

0136, 0252, 0370, 0097, 0128, 0388, 1532, 1037, 0562, 0038, 0039

Thorn-Ferguson 0362 0062

Tokyo 0062

Topline 0695 1064

Toshiba 1535

0535, 0062, 0745, 1609, 0580, 1764, 1316, 0222, 1457, 1064, 0268, 1583, 1962, 0645, 0677, 1972, 1731, 0097, 1943, 0036, 0136

Towada 0376 0579

Toyoda 0036

Trakton 0291

Triad 0583 0245, 0036, 0064

Trio 1672

Tristar 0291 0245

TVTEXT 95 0583

Uher 0064 0583, 0445, 0513, 0397, 0507

Ultravox 0064 0114, 0274, 0579, 0583

Unic Line 0064 0583, 0500, 0376

United 1679

1847, 1797, 0583, 1943, 1064, 0614, 2009, 2227, 0741, 0064, 0742

Universum 1064

0064, 0373, 1190, 0695, 1464, 0500, 0438, 0132, 0507, 1264, 0036, 0388, 0291, 0354, 0562, 0097, 0519, 1928, 0579, 0038, 0539, 1176, 0658, 0397, 0274, 0645, 0571, 0581, 0445, 0448, 0197, 0136, 0101, 0227, 2201, 0376, 0222, 1532, 0321, 1037

Univox 0064 0583, 0114

V7 Videoseven 1244 1693, 2281, 0907, 1403, 1294

Vestel 1064

1190, 1612, 1694, 0064, 0695, 0579, 0583

Vexa 0036 0064, 0583

Videologic 0245

Videosat 0274

VideoSystem 0064 0583

Viewpia 0903

ViewSonic 1569 1615, 1540, 2136, 2138

TV Brand

Brand

code

TV code(s)

Page 75

DCI85HD KD

Vision 0064 0583

Vistar 0388

Vortec 0064 0583

Voxson 0114 0064, 0583, 0445, 0205

Waltham 1064

0470, 0445, 0314, 0064, 0583, 0695, 0136

Watson 0064

1064, 0546, 0036, 0695, 1275, 1403, 1464, 0354, 0421, 0245

Watt radio 0571 0376, 0579, 0513

Wega 0064 0583, 0114

Wegavox 0036 0064, 0583

Welltech 1679

Weltblick 0064 0583

Weltstar 1064

Weston 0064 0583

White Westinghouse

0064 0583, 0651, 1936

Wilson 0583

Windy Sam 0583

World-of-Vision 0907

1759, 2028, 0917, 0892, 1316, 1325, 0904, 1633, 1244

Xomax 1797

Xoro 1816

2094, 1534, 2173, 1223, 1244, 1270, 2172

Xrypton 0064 0583

Yakumo 1640 2324

Yamaha 0677 0824, 1553, 1603

Yokan 0064 0583

Yoko 0064

0583, 0245, 0291, 0036, 0448, 0397, 0274

Yorx 0245

TV Brand

Brand

code

TV code(s)

Page 76

DCI85HD KD

10 Troubleshooting

Problem Solution

The remote control does not work.

• Press to switch to Receiver mode.

• Point the remote towards the Receiver.

• Check the batteries and check that the batteries are inserted

correctly.

The Receiver displays a black screen or an error message.

• Search for channels (see chapter 7.1.4, Delete additional

channels).

The picture is frozen and / or blurred.

• Check all connections, the antenna cable, and search for

channels again (see chapter 7.1.6, Start a channel search).

The Receiver cannot find any channels.

• Check the cable connection.

• Check the antenna signal (see chapter 2, Connections to

the network and connecting additional devices).

• Search for channels (see chapter 7.1.6, Start a channel

search).

• Check with your cable company for more information about

your home connection.

The TV does not recognize the Receiver if he leaves the standby mode.

• "Check if your TV is connected to the TV SCART connector

(see chapter 2, Connections to the network and connecting additional devices).

• "Select the SCART input on the TV, if necessary.

At some channels, no audio in Home Cinema mode is displayed.

• Check whether the Receiver is connected to a Home Cinema

amplifier via optical SPDIF connector (see chapter 2,

Connections to the network and connecting additional devices).

Black and white video at VCR output (during VCR / DVD recording).

• "Check that the mode selected for the VCR SCART output

type is compatible with your VCR (see chapter 7.2.3, Picture).

All other problems.

• Reset device to factory default (see chapter 7.1.7, Reset to

factory default).

Page 77

DCI85HD KD

11Support

This product has been designed with great care to ensure the best possible quality. In the unlikely case you have difficulties with the product and need advice or support, you can rely on the best possible help.

For technical problems with the product, you may contact Kabel Deutschland directly:

0800/ 52 666 25 Mon - Sun 0:00 - 24:00 (free of charge from Germany)

Page 78

DCI85HD KD

12 Explanation of terms

Term Definition

BER

Bit Error Rate The bit error rate defines the transmission quality from the number of

incorrectly transmitted bits.

EPG

Electronic Programme Guide Digital program guide, where you can view the programs, channels and

search for content.

FSK

Voluntary self-regulation of the film industry (Freiwillige Selbstkontrolle der Filmwirtschaft)

German organization that maintains a movie rating system, which draws on the parental control feature. The Receiver's replays content with classification G-16 or higher only if the parental protection PIN is entered.

Non entitled channels

Channels that are saved in the channel list but can not be displayed because you have no entitlement.

OSD

On Screen Display Menus and messages that are displayed on the screen.

Service Info

Text message that is sent from the channel or cable operator. See chapter

7.6.2, Service messages.

Smartcard

Electronic smartcard to decrypt encrypted digital TV or radio broadcasts. Slide the smartcard with the chip facing downwards into the reader of the Receiver to view programs for which you are unlocked.

Start Channel

Channel on which the Receiver systematically tunes to wherever the Receiver is switched on or woke up after standby.

Timeshift Mode

Time-shift recording mode, which allows to stop and rewind current broadcasts and watch it again.

Video Subchannel

Channels or programs that transfer more than one video channel at a time and offer you the option of choosing from different video channels.

VOD

Video on Demand (Select Video) Interactive services for direct retrieval of a wide range of programs. To use

this service, the Receiver must be connected to the internet, Select Video must be available in your region and you must be unlocked for this service.

Page 79

DCI85HD KD

13Specifications

TRANSMISSION STANDARDS

DVB-C, IP, MPEG-2, MPEG-4

CABLE FRONT END

CABLE RF INPUT Input frequency range: 47-862 MHz (6,

7, & 8 MHz BW)

RF input level: -15 to +15 dBmV

RF impedance: 75 Ohms

Tuning step: 62.5 kHz

RF OUTPUT Loop through output frequency

range: 47-862 MHz

CABLE DEMODULATOR

DVB-C Demodulator

Waveform QAM 16,32,64,128,256

Symbol rate: 1 to 6.96 MS/s Mbauds

Roll-off factor: 0.15

Decoder RS (204, 188, 8)

De interleaver: convolution type,

Depth l = 12

PROCESSOR AND MEMORIES

Processor: ST 7105 - 800 Mips

RAM memory: 256 Mbytes

Flash memory: 64 Mbytes

EEPROM emulated into Flash

ETHERNET 10/100BT

Fully integrated IEEE 802.3/802.3u

10/100 base T-Physical layer

Auto-negotiation 10/100

Full/Half Duplex

Adaptive equaliser

Baseline wander correction

VIDEO DECODING

MPEG2 Standard MPEG-2 MP@HL for 50 Hz

Input rates (max): 15 Mbit/s at ship

input

MPEG-4 Part 10 / H.264

- MPEG4 AVC HP@L4 (HD) for 50 Hz Input rates (max): 20 Mbit/s for HP@L4

- MPEG4 AVC HP@L3 (SD) for 50 Hz Input rates (max): 10 Mbit/s for HP@L3

CABAC and CAVLC decoding

Supports all intra/inter prediction

modes and block sizes I, P and B picture types

Fidelity range extensions (8x8

Transforms, 8x8 Spatial Prediction Mode, Dynamic Quantization Matrix)

AUDIO DECODING

MPEG-1 layer I & II (Musicam)

MPEG-2 layer II

Mode: Mono, stereo, joint stereo

Sampling rates 32, 44.1 or 48 KHz

HE-AAC

Dolby Digital

Dolby Pulse

Mode: pass through and down mixing

Mode: pass through, transcoding in

Dolby Digital, and down mixing

OUTPUT RESOLUTION FORMAT

For HD broadcast 1920x1080 @ 50 Hz progressive, or

1920x1080 @ 50 Hz interlaced and progressive (motion adaptative spatial and temporal de-interlacing)

(HD>SD) by set up menu

For SD broadcast 720x576 - Aspect ratio: 4:3 and 16:9

Conversion: Pan and Scan, Letter box

Scaling: SD > HD

HD or SD Resizing: down 1/4 and up no limit

SD INPUT/OUTPUT

TV SCART RGB out, CVBS, Y/C, Audio R/L

AUX SCART CVBS, Y/C, RGB in, Audio R/L

Protection Macrovision 7.0.1

CGMS-A

HDMI OUTPUT

HDMI 1.3 with HDCP 1.1 including CEC

Rely on the (E)EDID HDMI information

returned by the display device

AUDIO OUTPUT

Optical S/PDIF Two channels PCM in case of MPEG1-

layer II,

Originally received bit stream in case of

Dolby Digital

HiFi audio output Mono stereo in case of MPEG1 layer II,

Two channels down mixed in case of Dolby Digital

Page 80

DCI85HD KD

CONDITIONAL ACCESS

1 x Smart card reader, ISO/IEC 7816

DATA PORT

2 x USB 2.0 Host (High Speed)

1 x RJ45 (Ethernet 10/100 base T)

FRONT PANEL

1 x Smart Card reader

1 x IR sensor: 36 kHz

4 x Buttons (Standby, P+, P-, TV/radio

with LEDs)

1x USB 2.0 Host (High Speed)

REAR PANEL

1 x IEC169-2 (female: RF In)

1 x IEC169-2 (male: RF Out)

2 x SCART (TV, AUX)

1 x HDMI

2 x RCA Stereo L/R

1 x Optical S/PDIF

1 x RJ45 (Ethernet 10/100 base T)

1x USB 2.0 Host (High Speed)

1 x Power On/Off switch

POWER SUPPLY

Mains supply voltage: 220-240 V

~50 Hz

Max. Power consumption: 25 W

Standby mode: < 1 W

PHYSICAL SPECIFICATIONS

Receiver:

- Size (wxdxh): 310x175x41 mm

- Weight: ~0.780 Kg

- Operating temperature: 0°C to +40°C

- Storage temperature: -25°C to +65°C

ACCESSORIES

1 x Power cord for internal AC/DC

(1.8 m)

1 x Remote control

2 x Alkaline 1.5 V batteries (AAA type)

1 x HDMI cable (2 m)

1 x RF cable (2 m)

1 x Quick Installation guide

Page 81

Page 82

Sagemcom Broadband SAS

Headquarters: 250, route de l’Empereur

92848 Rueil-Malmaison Cedex - FRANCE

Tel : +33 (0)1 57 61 10 00 - Fax : +33 (0)1 57 61 10 01

www.sagemcom.com

All rights reserved. The information and speciﬁcations included are subject to change without prior notice. Sagemcom Broadband SAS tries to ensure that all information in this document is correct, but does not accept liability for error or omission.

Non contractual document. All trademarks are registered by their respective owners. Simpliﬁed joint stock company - Capital 35 703 000 Euros - 518 250 360 RCS NANTERRE.