Sagem D142 User Manual

D142

Handset keys

Intercom key

Earpiece

Red key: Talk off / Switch handset on/off

Access to phonebook / Navigation key down

Navigation key up / Access the caller list

Deactivate / Activate handset ringer (Press and hold)

Microphone

Screen

Access to outgoing call list

Menu key

OK key: Selection / Validation

Green key: Talk on

ctivate, deactivate keypad lock

(Press and hold)

R key: Second call / conference

Back key / Cancel / Correction /

Change standby screen

(Press and hold)

Mute:

ctivate / Deactivate the microphone

Quick guide to handset display icons

Signal strength icon (blinking when no signal or the signal strength is weak).

Call (blinks when you receiv e a call)

Voicemail icon: indicates that new messages are present in your voicemail box.

Handset ringer muted.

Received call list (appears when a new call is in the caller list).

Memory.

Charging status icon ( : Full ; + flashing (charger not connected) : Flat; blinking

during charging).

Changing the batteries

Make sure the telephone is OFF before you replace batteries.

1. Remove the batteries compartment door.

2. Remove old batteries.

3. Insert the batteries in the handset battery compartment respecting polarity.

4. Put the batteries compartment door back on.

5. Place handset in the base to charge.

D142

ENU STRUCTURE

Quick reference

phonebook New entry Clock&alarm date / time

List Set format

Edit entry Alarm

delete Alarm tone

delete all

Directe mem. Advanced set Change pin

registration

Unregister

contry

reset

Personal set Handset name AUTO PREFIX

Handset tone Recall time

LANguage Dial mode

Auto hang-up First ring

Navigation

To navigate among the menus, use the keys: MENU, or, OK and . Example: To change the ring tone, go to the menu Personal set / Handset tone / ring tones.

To do this:

1. Press MENU. Select " Personal set " using the  or key.

2. Press OK. Select " Handset tone " using the  or key.

3. Press OK. Select "ring tones " using the  or key.

4. Press OK. 10 melodies are available: " melody 1 "… " melody 10 ". Select the desired melody using the or key.

5. Press OK key to confirm your selection.

ALLS

Make a call

Ensure that the handset is switched on.

1. Press the Talk key

You will hear the dialling tone and the display will show you the phone icon

2. Enter the phone number.

- OR-

1. Enter the phone number first and then press

key.

Unava ilable Hide id

or

D142

3. You will then enter the name input screen and the cursor will be at the end of the name:

- The information is accurate. Press OK key.

- To correct the name, press

key to delete characters.

- Enter the new name and press OK key.

4. You will then enter the number screen and the cursor will be at the end of the number :

- The information is accurate. Press OK.

- To correct the number, press

to delete the numbers.

- Enter the new number and press OK.

Deleting a memory / the whole phonebook

1. Go to the menu " phonebook " / "delete " (or " delete all " to delete the entire phonebook list).

2. Select the entry you want to delete using  or . Press OK :

- If you do not wish to delete the entry, press

- To delete the entry, press OK.

Assign a shortcut

This menu allows you to record two quick dial numbers assigned to the keys 1 and 2 on the keyboard.

1. Go to the menu " phonebook " / " directe mem. ".

2. Select the key you want to assign a number (1 or 2).

3. Press OK, " no number " is displayed on the screen.

4. Press MENU.

5. " edit number " appears on the screen.

6. Press OK.

7. Enter the name of the entry and press OK to confirm.

8. Enter the number of the entry. Press OK to confirm. You will hear a confirmation tone. To call the number you have assigned to one of the shortcut keys, 1. Hold down the key on which the

number was programmed (1 or 2).

Inserting a pause (in dialling)

You can insert a pause in dialling a phone number if you want to wait before actually ringing.

While dialling the number you want to call, press and hold the key

to insert the pause:

The display shows a ’ ’P’’.

SING THE MULTI-HANDSET CAPABILITIES

These functions are used for handset management when two or more handsets are registered on the same base.

Intercom Call/Intercom

1. Make sure your handset is on standby mode.

2. Press the

key on the handset.

- If your installation has two handsets, the second handset is directly called, and, "handset " followed by the handset number are displayed on the screen.

- If your telephone installation has more than two handsets, the icon INT blinks on the screen and the number of all registered handsets.

- Enter the desired handset number or press the

key if you want to call all handsets.

D142

Answering an internal call

1. The ring melody from an internal call is different from an external call. " handset " and the calling handset number appear on the screen. The "

" is blinking.

2. Press the

key to answer. The " " stop blinking.

3. Ending an internal call press

Managing an external and an internal call

Transfering an external call to another handset registered on same base

1. During a call, press . The external user is put on hold.

2. Enter the internal call number. When the user answers, you can announce the call.

3. Press the

key to transfer the call.

To switch from one call to another, press and hold down the key until an aural signal is heard.

If the called handset does not answer, press to take back the call.

Making conference calls (3-way conversation) You can connect one external call to two handsets registered at the base station. To set up a telephone conference from an external cal l:

1. Press

. key. The external user is put on hold.

2. Enter the internal call number. Wait until the internal user answer s.

3. Press and hold

key, until an aural signal is heard to start a three-way conference. "conference"

is displayed on the handset screen.

Two outside calls

Taking a second call while you are already on line

During a call, a beep is emitted by your operator to inform you that a second call is on hold. A screen displays the number of this second caller on hold.

Press

then the key to take back this new call.

Your first contact is put on hold and you can tal k with the second caller.

Making a second call while you already on line

During a conversation, press

then dial the number to be called.

The call in process is then put on hold and you can take the second call back.

Switching from one call to the other

To switch from one call to the other, press

then the key .

The call in process is then put on hold.

Ending one of the two calls

To end one call and continue with the other, press then the key . The call in process is then ended finally and you take the second call back.

To set up a 3-way conference (the 2 calls and yourself)

During a conversation, press then the key . You can then talk with the 2 contacts at the same time.

To end the 3-way conference, press the red key

NTRODUCTION

Dear customer, Thank you for purchasing a Sagemcom DECT telephone we appreciate your trust in us. This product was man ufactured with the ut most care, should yo u encounter diffic ulties during its us e we

recommend that you refer to this user guide. You can also find information on the following site:

For your comfort and safety, we ask that you read the following section carefully :

ECOMMANDATIONS ET CONSIGNES DE SECURITE

Your DECT telephone must not be installed in a humid room (wash-up room, bathroom, laundry room, kitchen, etc.) unless it is 1.50 m away from a water point or outside. Your telephone must be operated at temperatures ranging from 5°C and 45°C.

Only use the supplied power adapter, connect it to the base socket according to the installation instructions provided in this booklet and the indications on the identification label affixed to it (voltage, current, electric network frequency). As a precaution, in case of danger, the mains adapters act as a disconnecting mechanism for the 230V power supply. They should be placed near the dev ice and should be eas ily accessible.

This telephone was designed for use on the public switched telephone network (PSTN). In case of a problem you must first contact your reseller. Only use the supplied telephone cord.

For your personal sa fety, never place yo ur handset on the base without the batter ies, or without the battery cover, you could get an electric shock.

To avoid damaging your handset, only use certified rechargeable AAA batteries NiMH

1.2 V 400 mAH, never use non rechargeable batteries. Insert the batteries in the handset battery compartment respecting polarity.

At the end of their useful life, batteries must be disposed of according to the recycling instructions present ed in this booklet.

Your DECT telephone has an inside radio range of about 50 metres and up to 300 metres in open space. The immediate presence of metal parts, (of a television for example), of any electric appliance may result in range reduction.

Some sensitive medical equipment and safety equipment may be affected by the radiofrequency transmissions of your telephone. In all cases, we ask that you respect the safety recommendations.

In areas where storm s are frequent, we r ecommend that you prot ect your telephone line using a surge protection device .

This equipment does not function in the case of an electric netw ork shutdown: for emergency calls, it is recommended to use another unit during power cuts.

The CE marking certifies that the product meets the essential requirements of Directive 1999/5/CE of the European Parliament and of the Council pertaining to microwave radio equipment and telecommunication terminal equipment, for the safety and health of users, for electromagnetic interference. Furthermore, it efficiently uses the frequency spectrum attributed to ground and spatial communication to prevent damaging interference.

The declaration of compliance may be looked up on the www.sagemcom.com site "support" section or can be obtained from the following address :

250, route de l'Empereur - 92848 Rueil-Malmaison Cedex - France

http://www.sagemc om.com

Sagemcom Broadband SAS

D142

EFORE YOU BEGIN

Make sure your package includes the following: Base unit, handset, one battery compartment cover, telephone line cord, AC power supply, two rechargeable batteries, and this user guide.

In the case of purchasing a pack duo or trio, you will find in addition for each additional handset: a handset charger, one battery compartment cover, two rechargeable batteries.

Installing the phone

Paging button

Rechargeable batteries

Telephone socket

1. Insert the batteries, taking care to respect the polarity as indicated in the compartment.

2. Put the compartment door back on. «SEARCHING...» appears on the screen.

3. Connect the end of the mains power unit lead to the bottom of the base and the mains power unit to the mains socket.

4. Plug the power supply cord into AC outlet and the other end into the power j ack on the base bottom.

5. A welcome message in all the languages supported by the telephone is displayed on the screen, press OK *. You will hear a confirmation tone.

Place the handset in the base station to charge for 15 hours prior to first use.

6. After charging, press

* :

depending on country

key. You can hear dial tone.

- Pressed briefly : telephone set paging.

- Hold down pressed (4 seconds minimum) : telephone set registration.

Power socket

D142

Answering a call

When the phone rings, press the key to answer the call.

Ending a call

To end a call press .

Microphone mute function

- Enable M UTE function: press the key. The display shows "mute on".

- Disabl e MUTE function: press the

Voice Mail (According to operator)

With this function you can receive calls in your absence on a voice message recorder in the switched

telephone network. To indicate that a new message has been received the envelope icon new event message "

- Dial the number of your operator’s voice message recorder.

- The envelope icon

ALL LOG

Calling line identification presentation (CLIP)

This CLIP phone stores and displays CLIP information provided by your local telephone company. You must subscribe to CLIP service in order to use this unit. If you have not subscribed to CLIP service or if the caller number is suppressed, the display shows “unknown”.

Received call log

The received call log presents the calls you received. (max.10 last calls).

6. Press

7. The most recent name or call number is displayed according to whether your contact's number is included in your phonebook or not.

8. Press OK to display the date and the time of the call.

9. Press the or  key to go through the list.

You can adjust the volume of what you hear through the handset at any time by pressing  or  ҏkey.

voicmail

, the icon is displayed.

" are displayed on the Handset screen.

Your voicemail number is not set in the factory.

disappears when there are no more new messages.

Display of numbers not available:

If the number is too long (more than 12 digits), the screen will not show the number in full. Press OK key to go to last number page for CID length.

: you are not in same area as your contact.

: your contact does not want their number to be displayed.

key. Your correspondent can hear you again.

and the

Diallled call log

The dialled call log presents the calls you made (max. 5 last calls).

To consult the list:

1. Press briefly

2. The last dialled number is displayed. Press the

key to consult the list of the last 5 numbers dialled.

Calling back a caller

1. Press the or key.

2. Press the or  key to select a call r ecord.

3. Press the key to dial the number.

Making an entry in the directory from the list of calls received.

1. Press the or key.

2. Use  or  to select the desired caller number.

3. Press MENU key, then select "save number ".

4. Enter the name of the entry. Pr ess OK.

Deleting caller list record

1. Press the or key.

2. Press or  key to select a call record.

3. Press MENU.

- Select " delete " to delete the current record.

- Select " delete all " to delete the entire Caller list.

4. A confirmation screen appears.

5. Using the telephone touch keys:

- If you do not wish to delete the current record, press

- To confir m the deletion of the entry, press OK.

HONEBOOK

You can store 50 phonebook entries (24 digits and 12 characters) in your phonebook.

Dialling a memory number

1. Press key to consult the list of contacts.

2. Press theor  key to consult dire ctory entries.

3. When you have selected the desire number, press

Creating / Storing a memory

1. Go to the menu " phonebook " / " new entry "

2. Enter the name of the entry. Pr ess OK.

3. Enter the number of your entry using the keypad keys. Press OK.

Editing a memory

1. Go to the menu " phonebook " / " edit entry ".

2. Select the entry you want to edit using or . Press OK.

D142

Association handset & base

1. Press and hold key for 5 seconds (after 1 minute if no Handset has started association process the base goes back to standby).

2. Go to the menu " advanced set " / " registration ".

3. Enter the 4 digit base master PIN code (default 0000). Press OK.

4. Once the handset is registered. The handset automatically exits the registering mode.

5. The handset number assigned automatically by the base appears on the screen.

Disassociation of a handset

1. Go to the menu " advanced set " / " unregister ".

2. Enter the 4 digit base master PIN code (default 0000). Press OK.

3. Select the handset you want to delete using the  or  key then pre ss OK (at standby state, "pls reg h/s" is displayed on the screen.

Selecting the country

1. Go to the menu " advanced set " / " unregister ".

2. Enter the 4 digit base master PIN code (default 0000). Press OK.

3. Select the country where you are using the telephone. Press OK.

4. A confirmation screen appears, press OK.

Restoring the Handset / Base Default Settings

1. Go to the menu " advanced set " / " reset ".

2. A confirmation screen appears, press OK.

Prefix (Depending on Country)

If a PABX is used in a private network, you can program the outside call prefix. This function sets:

- The PAB X prefix number: this number will be added at the beginning of the number you dialled.

- The number to be detected: if the number you dialled starts with the recorded sequence, this sequence will be automatically deleted.

These two settings are not applied if number you dialled starts with "#", "*" or "P".

1. Go to the menu "advanced set " / "auto prefix ".

- Select "detect digit " to define the number giving you access to the outside line.

- Select "prefix" to specify the «digits before prefix».

2. Press OK.

Flash timing

If you connect your telephone to a private automatic branch exchange or use it in a foreign country, you may need to modify the flash duration in order to use your telephone correctly with regard to the following functionalities: outgoing 2nd call, incoming 2nd call, conference call. Contact your administrator, who will supply the appropriate time period, and proceed to the new settings.

1. Go to the menu " advanced set " / " recall time ".

2. Select the appropriate time period, press OK.

Modifying the dialing mode

Most telephone systems use the tone dialling mode. You can, however, use the pulse dialling mode:

1. Go to the menu " advanced set " / " dial mode ".

2. Two modes are available: " tone " and " pulse ".

3. Press OK.

D142

The product

The crossed-out waste bin stuck on the product or its accessories means that the product belongs to the family of electrical and electronic equipments. In this respect, the European regulations ask you to dispose of it selectively:

At sales points in the event of the purchase of similar equipment.

At the collection points made available to you locally (drop-off centre, selective collection, etc.).

In this way you can partic ipate in the re-use and u pgrading of Electric al and Electronic Equipm ent Waste, which can have an effect on the environment and human health.

ERMS AND CONDITIONS FOR UNITED KINGDOM &IRELAND ONLY

In order to apply the guarantee, you should contact the SAGEMCOM Helpdesk or the retailer where you purchased the equipment. Proof of purchase will be required in either case. Please make sure that you use your equipment only for the purpose for which it was designed and under normal usage conditions. SAGEMCOM do not accept any liability for the equipment if used outside the frame o f its original designed purpose or any consequence that may arise from this usage. Should any malfunction arise, the SAGEMCOM Helpdesk or your retailer will advise you how to proceed.

A) General Guarantee conditions

SAGEMCOM undertakes to remedy by repair or exchange at its own convenience, free of charge for l abour and replacement parts, any defects in the equipm ent during the guaran tee period of 12 (twe lve) months or 3 (three) months for accessories, from the date of original invoice of the Equipment, where those defects are a result of faulty workmanship. Unless the customer has concluded with SAGEMCOM a maintenance contract in respect of the equipment which specifically provides for repairs to be carried out at the customer's premises, the repairs will not be carried out on the equipment at the customer premises. The customer must however return the defective equipment at his/her own expense, to the address supplied by the SAGEMCOM Helpdesk or by the retailer. In the case that a prod uct needs to be sent i n for a repair, it mu st always be accompa nied by a proof of pur chase (which is not altered, written on or in any way made illegible) showing that the product is still under guarantee. In the case that no proof of purchase is enclosed, the SAGEMCOM repair centre will use the pr oduction date as its reference for establishing the guarantee status of the product. Apart from all legal obligatory rules, SAGEMCOM, do not give any Guarante e, either implicit or explicit which is not set force in the present section, and can not be held responsible for any direct or indirect, material or immaterial damage, either in or out of the frame of the present guarantee. If any provision of this guarantee shall be held to be in whole or in part invalid or illegal due to an obligatory rule applicable to consumers pursuant to their national legislation, such invalidity or illegality shall not impair or affect the remaining provisions or parts of this guarantee. This guarantee does not affect the Customer statutory rights.

B) Exclusions From Guarantee

SAGEMCOM shall have no liability under the guarantee in respect of: x Damage, defects, breakdown or malfunction due to one or more of the following:

- Failure to properly follow the installation process and instructions for use

- An external cause to the equipment (including but not limited to: lightening, fire, shock, vandalism, inappropriate conditions of electrical network or water damage of any nature)

- Modifications mad e without the written approval of SAGE MCOM

- Unsuitable operating conditions, particularly of temperature and humidity

- Repair or mai ntenance of the equipmen t by persons not authori sed by SAGEMCOM

x Wear and tear from normal daily use of the equipment and its accessories x Damage due to insufficient or bad packaging of equipment when return ed to SAGEMCOM x Usage of new versions of software without the previous approval of SAGEMCOM x Work on any equipment or software modified or added without the prior written consent of SAGEMCOM

D142

x Malfunctions not resulting from the Equipment or from software installed in user workstations for the

purpose of use of the equi pment Communication problems related to an unsuitable environment including:

- Problems related to access and/or connection to the Internet such as interruptions by access networks or malfunction of the line used by the subscriber or his correspondent

- Transmission faults (for example poor geographical coverage by radio and TV transmitters, interference or poor line quality)

- Local netwo rk faults (wiring, serv ers, workstations) or the fa ilure of the transmiss ion network (such as but not limited to interferences, fault or poor quality of the network

- Modification of the parameters of the cellular or broadcast network carried out after the sale of the Product

x Normal servicing (as defined in the user guide supplied with the equipment) as well as malfunctioning due

to servicing not being carried out. Servicing costs are in any event always borne by the customer.

Malfunctions resulting from the usage of products, consumables or accessories not compatible with the

equipment.

Out of Guarantee Repairs

In the cases set fort h in B) as well as after expiry of the guara ntee period, the cust omer must ask the Aut horised SAGEMCOM Repair Centre for a cost estimation prior to work being carried out. In such cases, the repair and delivery costs will be invoiced to the customer. The foregoing shall apply unless otherwise agreed in writing with the customer and only for the United Kingdom and Ireland.

www.sagemcom.com

ERMS AND CONDITIONS FOR OTHER COUNTRIES

If, despite our best ef forts, your product pr esents any defects, you s hould refer to your ret ailer and present th e proof of purchase that they gave you on the day of purchase. Should any malfunctioning arise, the retailer will advise you what to do. For the warranty to appl y, you should ensure t hat the product was us ed in accordance with t he instructions for use and the purpose for use, and that you have at your disposal the sales invoice or receipt stating the date of purchase, the name of the retailer, the re ference and the seri al number of the produ ct. No coverage shall be given under this warranty if the following conditions are applicable:

x The require d documents have been mo dified or altered in orde r to take advantage of t he warranty. x The manufacturing numbers, product brands or labels have been altered or made illegible. x Interventions on the product have been made by an unauthorized person. x The product has been subjected to abnormal or improper use. x The product has been damaged by external factors such as lightning, over-voltage, moisture, accidental

damage, improper care as well as all Acts of God. This present warranty does not affect the consumer rights that you may have under the laws in effect in your country

Important:

Should you return the product to the after-sales department, please ensure that you return as well all the elements and accessories originally supplied with the product. x accidental damage, improper care as well as all Acts of God. This present warranty does not affect the consumer rights that you may have under the laws in effect in your country

USTOMISING THE HANDSET

Handset naming

The default name of the handset is "

1. Go to the menu " personal set " / " handset name ".

2. Use the keypad to enter the new name (up to 10 characters).

Use

key to delete wrong input if necessary. Press OK.

Handset ringer level

1. Go to the menu " personal set " / " handset tone " / " ring volume ".

2. Use or  to select the volume level then press OK to confirm your selection.

Handset ringer melody

1. Go to the menu " personal set " / " handset tone " / " ring tones ".

Ten melodies are available: " melody 1 "… " melody 10 ".

2. Use or  to select the ring tone. Press OK.

Key tone On/Off

1. Go to the menu " personal set " / " handset tone " / " key beep ".

An information screen shows you the current state. Use or  to modify it.

2. Press OK key to confirm your selecti on.

Modifying the language

1. Go to the menu " personal set " / " language ".

2. Use or to choose the desired language. Press OK key to confir m your selection.

Auto talk

When active, the auto talk off feature enables you to automatically hang up as soon as you put the handset on its base.

1. Go to the menu " personal set " / " auto hang-up ".

An information screen shows you the current state. Use  or  to modify it.

2. Press OK key to confirm your sele ction.

Key lock

1. Press and hold key for 1 second. An information screen shows you that the keys are locked.

2. To recover to normal, press and hold

ETTING THE DATE AND TIME

Time and date

After a power cut the time has to be reset.

1. Go to the menu " clock & alarm " / " date/time". Current date is displayed.

- To keep the date, press OK.

- To change it, enter the new date in 20YY/MM/JJ format.

- To go back to change the entry

handset N

" where N is the number of the registered handset.

key 1 sec.

D142

2. Press OK. Current time is displayed.

- To keep the time, press OK.

- To change it, enter the new time in the HH : MM format. (If, after entering the time, the time format is 12H, use the  key to set aM and the  key to set pM).

- To go back to change the entry

3. Press OK.

Hour format (12/24)

1. Go to the menu " clock & alarm " / " set format " / " time format ". A screen displays the current format, use  or to change it.

2. Press OK.

Date format

1. Go to the menu " clock & alarm " / " set format " / " date format ". A screen displays the current format, use  or  to change it.

2. Press OK.

Alarm clock

1. Go to the menu " clock & alarm " / " alarm ".

 To activate the alarm once, select "on once ".  To repeat the alarm each day at the programmed time, select " on daily ".  To deactivate the alarm, select "off ".

2. Select your choice then press OK. Enter the time when you want the alarm to go off: "HH – mm ". (If after entering the time, the time format 12H, use  key to set

3. Press OK.

Modifying alarm tone

1. Go to the menu " clock & alarm " / " alarm tone ". 3 melodies are available: "melody 1", "melody 2" et "melody 3".

2. Select the desired melody, press OK key to confirm your selection. You will hear a confirmation tone.

DVANCED SETTINGS

Base master PIN code

Your base station code (default se tting 0000) is required to access certain security functions. This code can include 8 digits.

1. Go to the menu " advanced set " / " change pin ".

2. Enter your old code first, press OK.

3. Enter your new PIN code. Each time a digit is entered the «_»is replaced by a «*». Press OK key to confirm your new PIN code. You will hear a confirmation tone.

Carefully note your base station code. You will need it to change certain settings.

and the keyto set pM).

D142

First ring

When this function is activated, the receiver rings as soon as a call is received, without waiting for the number to be displayed. If you have activated this function, it will be automatically deactivated when a call is received with the number displayed (if you have this service).

1. Go to the menu " advanced set " / " first ring ".

2. Use the or keyto change the state.

3. Press OK.

ATTERIES SAFETY PRECAUTIONS

To avoid any risk of explosion:

 Make sure you have inserted the batteries correctly.  Use only with 1,2V 400mAh type or equivalent rechargeable batteries pack.  Do not dispose of the batteries in a fire. The cell may explode.  Check with local code for possible special disposal instructions.  Do not burn, disassembl e, mutilate or punct ure. Like other batte ries of this type, t oxic materials could be

released which can cause injury.

 To reduce the risk of fire or personal injury, use only the battery listed i n the user’s guide.  Keep batteries out of the reach of children.  Remove batteries if storing over 30 da ys.

ENERAL PRODUCT CARE

To keep your telephone wor king and looking good, fol low these guidelines:  Avoid putting the phone near heating appliances and devices that generate electrical noise (for example,

motors or fluorescent lamps).

 DO NOT expose to direct sunlight or moisture.  Avoid dropping and other rough treatment to the phone.  Clean with a soft cloth.  Retain the original packaging in cas e you need to ship the phon e at a later date.

ROUBLESHOOTING

Causes of poor reception:

 Aluminium siding.  Foil backi ng on insulation.  Heating duc ts and other metal const ruction can shield radi o signals.  You are too close to appliances such as microwaves, stoves, computers, etc).  Atmospheric conditions, such as strong storms.  Base instal led in the basement o r lower floor of the house.  Base is plugged into an AC outlet with other electronic devices.  Baby monitor is using the same frequ ency.  Handset batteries is low.  You are out of range of the base.

D142

Auto-diagnostics

Problem Solution

No display.

Handset does not ring.

You experience static, noise or fading in and

out

Unit beeps

- Place handset in base for 20 seconds to reset the security code. If that doesn’t work, charge batteries for 15 hours.

- Clean chargi ng contacts on handset and base with a soft cl oth

- Replace batteries.

Memory dialling

- Did you program the memory location keys correctly?

- Did you follo w proper dialling seque nce?

- Make sure the tone/pulse setting is correct.

- Did you reprogram numbers into memory after power outage or batteries replacement?

NVIRONMENT

Preservation of the environment is an essential concern of SAGEMCOM. The desire of SAGEMCOM is to operate systems observing the environment and consequently it has decided to integrate environmental performances in the life cycle of its products, from manufacturing to commissioning, use and elimination.

Packaging

Batteries

x Make sure the batteries are properly installed. x Place the handset on the base and fully charge the batteries. x To increase the life of your batteries, you can perform this operation about

every two months.

x If these precautionary measures do not resolve thi s issue, replacemen t

batteries are available through your reseller.

x As time goes by, you may notice a slight decrease in battery performance. Use

your handset until the battery is fully discharged, and then charge it for at least 15 hours.

x Make sure the RINGER setting on the handset is programmed to ON. x You may have too many extension phones on your l ine. Try unplugging some

phones.

x Is handset out of range?

Move closer to the base.

x Does the base need to be relocated? x Charge batteries. x Make sure base is not plugged into an outlet with another household appliance.

The presence of the logo (green dot) means that a contribution is paid to an approved national organisati on to improve pack aging recovery and r ecycling infrastru ctures.

To facilitate recycling, please respect the sorting rules set up locally for this kind of waste.

If your product contains batteries, they must be disposed of at appropriate collection

points

253437152A