Saeco Moltio HD8768 AMF User Manual

Saeco Moltio

HD8768

AMF

Buttons and symbols:

Machine Settings:

• Memo setting, cup volume.

Espresso and Coffee button can be adjusted
and set to your preference.

1. Place a cup under the dispensing spout.

2. Press and hold the espresso/coffee button until the
“MEMO” icon is displayed. Then release the button.

3. Press the espresso button when the desired amount
is reached. Also when adjusting the coffee button.

Aroma Setting:

Five strength choices are possible by pressing

the “Aroma" button.

= extra mild aroma
= mild aroma

= medium aroma

= strong aroma
= extra strong aroma
= pre-ground coffee

Product dimensions and information

• Product dimensions (L x D x H): 256 x 470 x 350 mm

• Coffee bean capacity: 290 gr

• Waste container capacity: 15 servings

• Water tank capacity: 1.9 l

• Maximum cup height: 142 mm

• Product weight: 8.5 kg

• Grind settings:

The grinder can be set with the grinder
adjustment key. Remove first the bean
container.

1. Coarse grind: lighter taste, for dark roasted

coffee blends

2. Fine grind: bolder taste, for light roasted
coffee blends.

• Water hardness setting:

The water hardness can be measured with
the supplied tester strip.

1. Immerse the strip 1 sec. in water.

2. Check how many squares have changed
to red and consult the table.

3. The numbers on the strip correspond to the
water hardness adjustment settings.

4. To set the hardness on the machine; Press

the Menu button until the hardness setting

appears and select the number.

Cleaning and Maintenance:

• Empty drip tray:

Empty and clean the drip tray each time
the ‘drip tray full’ indicator pops up through
the drip tray cover.

• Empty Coffee ground container:

Always empty the container when the machine is
switched ON and when the empty symbol appears.

• Descaling:

Descale the machine when the calc clean
symbol appears. Start the descaling and
follow the instructions on the display.
Only use the Saeco decalcifier CA6700. It takes approx. 35
min. Finish the complete descale process till the end without

interruption.

• Brew group cleaning:

Support movies available within the FAQ’s;

how to lubricate/how to clean.
Clean the brew group weekly. Take it out and wash it with

fresh, lukewarm water. Clean it monthly with the coffee oil

remover tablet CA6704.
Lubricate the brew group once a month or if needed after
cleaning. Use Saeco grease HD5061.

• Cleaning Automatic milk frother:

Daily: Rinse for hygiene and to ensure perfect milk
froth

Weekly: Detach all parts and clean thoroughly.
Monthly: Clean with the Saeco Milk Circuit Cleaner CA6705.

• Cleaning coffee duct outlet (coffee funnel):

Clean the coffee duct outlet every time you clean the brew
group. Take out the brew group and clean the coffee duct
outlet with a spoon handle.

• Water pressure in pump: 15 bar

• Supported coffee types: Ground

coffee and Whole coffee beans

• Automatic Milk Frother

First time use: Machine needs to be installed and primed.

1. Insert the drip tray.

2. Rinse and fill the water tank with fresh water up to the MAX level.

3. Pour coffee beans into the coffee bean hopper.

4. Insert the plug and switch the power button to “I”. (back of the machine).

5. To turn on the machine, press the “ON/OFF ” button on the front.

6. The display will indicate you have to prime the circuit.

7. Place a container under the steam wand.

8. Press the Espresso button to start the priming. After this he machine starts
heating up and performs an automatic rinse cycle trough the coffee spout.

9. Perform a manual rinse by dispensing some hot water wand and brew a pre-ground coffee
without adding coffee.

Display

Brew group:

How to remove:

1. Turn OFF the machine.

2. Open the service door.

3. Remove the coffee ground drawer.

4. Remove the coffee ground container.

5. Press the PUSH button and pull the brew group out.

How to insert, set in rest position:

Important! If the brew group does not stand in the rest position, it cannot be reinserted.

How to set the brew group in the rest position

1. The lever must be in contact with the brew group base. Push it down.

2. The two arrow heads on the side of the brew group will now match.

3. The locking hook on the side of the brew group needs to be in uppermost position. Push it
upwards until you hear a soft click.

Display messages during descaling:

Start
process

Add the
descaling
solution.

The machine is in
the descaling
cycle. It
dispenses at
intervals.

The descaling
cycle is finished.
Rinse and fill the
water tank with
fresh water.

The machine

is ready to
start rinsing
cycle

During descaling cycle:

During rinsing cycle:

Start descaling:

Refill the
tank and

repeat

rinsing cycle.

The rinsing
cycle is
completed
and you can
exit

The machine
warms up
and performs
an automatic

rinse cycle.

• The complete process consists of 3 cycles; One descaling cycle with the specific Saeco decalcifier CA6700 and two rinsing cycles with fresh water.

• Before starting the descaling process: Remove the automatic milk frother, empty the drip tray and remove any extra placed water filter (example. INTENZA+) from the water

tank.

Compact description descaling process:

Start descaling:

1. Press the “Menu" button until the CACL CLEAN symbol appears.

2. Press the “Espresso ” button to start the descaling . The descaler symbol appears on the display.

Descaling cycle:

3. Take out the water tank. Pour the entire bottle of Saeco descaling solution in the water tank.

4. Top up the water tank with fresh tap water to the Calc Clean line. Place the water tank back into the machine.

5. Place a bowl underneath the steam/hot water wand and the dispensing spout.

6. Press the “Espresso” button to start the descaling cycle. The machine will start dispensing the descaling solution at intervals. The bar on the display shows the progress. This
takes about 25 minutes. Note: The descaling cycle can be paused by pressing the “Espresso” button .To resume the cycle, press the “Espresso” button again.

7. When the mixture of descaling solution and water has been used up, the ‘water tank empty’ symbol appears on the display.

Rinsing cycles:

8. Clean the water tank thoroughly, fill it with fresh water to the MAX and place it back. The ‘start rinsing’ symbol appears on the display.

9. Place back the bowl. Press the “Espresso ” button and the machine starts the first rinsing cycle.

10. When the ‘water tank empty’ symbol appears on the display, repeat steps 8-9 to start the second rinsing cycle.

11. When it is finished the ”Calc Clean ready” symbol appears to indicate that the descaling process has been completed. Exit the descaling process.

Important note: If the ‘water tank empty’ symbol appears on the display instead of the ‘Calc Clean ready’ symbol, you did not fill the water tank up to MAX level. Refill

the water tank up to MAX level and perform another rinsing cycle. Repeat steps 8-9 unti l the ‘Calc Clean ready’ symbol appears. You may have to do this several times
before the ‘Calc Clean ready’ symbol appears.

12. If the machines shows the prime circuit symbol, first start priming the circuit before brewing any coffee.

Remove Bean container

and detach: To remove push

the selector to the unlock position
Lift the container with both hands.
To detach the two parts of the

coffee bean container, turn it and

push down the small hooks in the
bottom.

Automatic milk

frother: Insert the

Automatic Milk Frother in
the steam wand seat.
Make sure that it is
positioned correctly. If you

cannot insert it, rotate the

chrome cover.