Ryobi RLM12LT300 Instruction manual

Page 1
RLT3123
ORIGINAL INSTRUCTIONS
Electric Line Trimmer
Page 2
Important!
It is essential that you read the instructions in this manual before assembling, operating and maintaining the product.
Subject to technical modification.
Page 3
Safety, performance, and dependability have been given top priority in the design of your electric line trimmer.
INTENDED USE
The product is only intended for use outdoors by a standing operator.
The product is designed for cutting grass, light weeds and other similar vegetation at or about ground level. The cutting plane should be approximately parallel to the ground surface.
The product should not be used to cut or trim hedges, bushes or other vegetation where the cutting plane is not at or about ground surface level.
GENERAL SAFETY WARNINGS
WARNING
When using the product, the safety rules must be followed. For your own safety and that of bystanders, please read these instructions before operating the product. Please keep the instruction safe for later use.
WARNING
This product is not intended to be used by children or persons with reduced physical, mental or sensory capabilities. Children should be adequately supervised to ensure they do not play with the product.
WARNING
Some regions have regulations that restrict the use of the product. Check with your local authority for advice.
TRAINING
Ŷ Never allow children or people unfamiliar
with these instructions to use the product. Local regulations may restrict the age of the operator.
Ŷ Read the instructions carefully. Be familiar
with all controls and the proper use of the product.
Ŷ Keep bystanders, children and pets 15m
away from the area of operation. Stop the product if anyone enters the area.
Ŷ Never use the product when you are tired,
ill or under the influence of alcohol, drugs or medicine.
Ŷ Keep in mind that the operator or user
is responsible for accidents or hazards occurring to other people or their property.
ELECTRICAL SAFETY
Ŷ Power plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
Ŷ Avoid unintentional starting. Always check
that the switch is in Off position before plugging in the product to the power supply. Do not carry a plugged in product with your finger on the switch.
Ŷ Avoid body contact with earthed or
grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
Ŷ Do not operate the product when there is a
risk of lightning.
Ŷ Do not expose the product to rain or wet
conditions. Water entering an appliance will increase the risk of electric shock.
Ŷ Electrical power should be supplied via
a residual current device (RCD) with a tripping current of not more than 30 mA.
Ŷ Before every use, examine the power
cord for damage. If there are signs of damage, it must be replaced by at an Authorized Service Centre. Always uncoil the power cord during use, coiled cables can overheat.
Ŷ If you need to use an extension cable
ensure it is suitable for outdoor use and has a current capacity sufficient to supply your product. The extension cord cable should be marked with either “H05 RN­F” or H05 VV-F”. Check it before every use for damage, always uncoil it during use because coiled cables can overheat. Damaged extension cables should not be repaired, they should be replaced with an equivalent type.
Ŷ Do not use the product if the electric cables
are damaged or worn.
Ŷ If the power cord or extension cable
becomes damaged during use, disconnect
Page 4
from the power supply immediately. Do not touch the electric cables until the power supply has been disconnected.
Ŷ Make sure the power cord is positioned so
that it cannot be damaged by the cutting means and will not be stepped on, tripped over or otherwise subjected to damage or stress.
Ŷ Never pick up or carry the product by the
electric cable.
Ŷ Never pull by the power cord to disconnect
from the power supply.
Ŷ Keep the power cord away from heat, oil
and sharp edges.
Ŷ Make sure voltage is correct for your
product. A nameplate on the product indicates the product’s voltage. Never connect the product to an AC voltage that differs from this voltage.
Ŷ Make sure the switch is in Off position
before disconnecting from power supply.
PREPARATION
Ŷ Wear full eye and hearing protection while
operating the product. If working in an area where there is a risk of falling objects, head protection must be worn.
Ŷ Hearing protection may restrict the
operators ability to hear warning sounds, pay particular attention to potential hazards around and inside the working area.
Ŷ Wear heavy long trousers, boots, and
gloves. Do not wear loose fitting clothing, short trousers, jewellery of any kind, or use with bare feet.
Ŷ Secure long hair so it is above shoulder
level to prevent entanglement in moving parts.
Ŷ Before use and after any impact, check that
there are no damaged parts. A defective switch or any part that is damaged or worn should be properly repaired or replaced by an authorized service facility.
Ŷ Make sure the cutting attachment is
properly installed and securely fastened.
Ŷ Never operate the product unless all
guards, deflectors and handles are properly and securely attached.
Ŷ Consider the environment in which you are
working. Keep the working area free from wires, sticks, stones and debris which if
struck by the cutter can become thrown objects.
LINE TRIMMER SAFETY WARNINGS
Never allow children, persons with reduced
Ŷ
physical, sensory or mental capabilities or lack of experience and knowledge or people unfamiliar with these instructions to use the product. Local regulations may restrict the age of the operator.
Ŷ Use the product in daylight or good artificial
light.
Ŷ Avoid using on wet grass. Ŷ Keep proper footing and balance at all
times.
Ŷ Do not walk backwards when using the
product.
Ŷ Keep firm footing and balance. Do not
overreach. Overreaching can result in loss of balance. Always be sure of the footing on slopes, and walk, never run.
Ŷ Keep bystanders, children and pets 15m
away from the area of operation, stop the product if anyone enters the area.
Ŷ Keep the cutting attachment below waist
level.
Ŷ Never operate the product with damaged
guards or without guards in place.
Ŷ Never fit a metal replacement line. Ŷ Keep hands and feet away from the cutting
means at all times and especially when switching on the motor.
Ŷ Beware, the cutting elements continue to
rotate after the motor is switched off.
Ŷ Beware of objects thrown by the cutting
means. Clear debris like small stones, gravel and other foreign objects from the work area before starting operation. Wires or string may become entangled with the cutting means.
Ŷ Switch off and disconnect from the power
supply before:
Ɣ servicing Ɣ leaving the product unattended Ɣ cleaning your product or clearing a
blockage
Ɣ changing accessories Ɣ checking for any damage after hitting an
object
Ɣ checking for any damage if the product
Page 5
starts to vibrate abnormally
Ɣ performing maintenance
Ŷ The small blade fitted to the lawn guard
is designed to trim the new extended line to the correct length for safe and optimum performance. It is very sharp, do not touch it particularly when cleaning the product.
Ŷ Always ensure that ventilation openings
are kept clear of debris.
Ŷ Make sure the cutting head attachment is
properly installed and securely fastened.
Ŷ Make sure all guards, deflectors and
handles are properly and securely attached.
Ŷ Do not modify the product in any way, this
may increase the risk of injury to yourself or others.
Ŷ Use only the manufacturer’s replacement
cutting line. Do not use any other cutting attachment.
Ŷ Immediately switch off and disconnect from
the mains once in the event of accident or breakdown. Don’t operate the product again until it’s fully checked by authorised service center.
TRANSPORTATION AND STORAGE
Ŷ
Stop the product and allow it to cool before storing or transporting.
Ŷ Clean all foreign material from the product.
Store it in a cool dry and well-ventilated place that is inaccessible to children. Keep away from corrosive agents such as garden chemicals and de-icing salts. Do not store outdoors.
Ŷ For storage, always disconnect from power
supply and wind cable.
Ŷ For transportation, secure the product
against movement or falling to prevent injury to persons or damage to the product.
MAINTENANCE
WARNING
Use only original manufacturer’s replacement parts, accessories and attachments. Failure to do so can cause possible injury, poor performance and may void your warranty.
WARNING
Servicing requires extreme care and knowledge and should be performed
RQO\ EH D TXDOL¿HG VHUYLFH WHFKQLFLDQ )RU
service we suggest you return the product to your nearest authorized service center for repair. When servicing, use only identical replacement parts.
Ŷ Switch off and disconnect from the mains
before: conducting any maintenance or cleaning work.
Ŷ You may make adjustments and repairs
described here. For other repairs, contact the authorized service agent.
Ŷ For replacement line use only nylon
filament line of the diameter described in the specification table of this manual
Ŷ After extending new cutter line, always
return the product to its normal operating position before starting.
Ŷ After each use, clean the product with a
soft dry cloth. Any part that is damaged should be properly repaired or replaced by an authorized service centre.
Ŷ Check all nuts, bolts and screws at frequent
intervals for proper tightness to ensure the product is in safe working condition.
RESIDUAL RISKS
Even when the product is used as prescribed, it is still impossible to completely eliminate certain residual risk factors. The following hazards may arise in use and the operator should pay special attention to avoid the following:
Ŷ Injury caused by vibration. Hold the product
by designated handles and restrict working time and exposure.
Ŷ Exposure to noise can cause hearing injury.
Wear ear protection and limit exposure.
Ŷ Eye injury due to flying debris. Wear eye
protection at all times.
RISK REDUCTION
It has been reported that vibrations from hand-held products may contribute to a condition called Raynaud’s Syndrome in certain individuals. Symptoms may include tingling, numbness and blanching of the
¿QJHUV XVXDOO\ DSSDUHQW XSRQ H[SRVXUH WR
Page 6
cold. Hereditary factors, exposure to cold and dampness, diet, smoking and work practices are all thought to contribute to the development of the these symptoms. There are measures that can be taken by the operator to possibly reduce the effects of vibration:
Ŷ Keep your body warm in cold weather.
When operating the product wear gloves to keep the hands and wrists warm. It is reported that cold weather is a major factor contributing to Raynaud’s Syndrome.
Ŷ After each period of operation, exercise to
increase blood circulation.
Ŷ Take frequent work breaks. Limit the
amount of exposure per day.
If you experience any of the symptoms of this condition, immediately discontinue use and see your doctor about these symptoms.
WARNING
Injuries may be caused, or aggravated, by prolonged use of a tool. When using any tool for prolonged periods, ensure you take regular breaks.
Wear eye protection.
Wear hearing protection.
Do not use metal blade(s) on the product.
Do not expose to rain or damp condition.
Remove plug from the mains immediately before maintenance or if cable is damaged, cut or entangled.
%HZDUHRIWKURZQRUÀ\LQJ
objects. Keep all bystanders a safe distance away from the product.
%HZDUHRIWKURZQRUÀ\LQJ
objects. Keep all bystanders, especially children and pets, at least 15m away from the operating area
KNOW YOUR PRODUCT
See page 7.
1. Rear handle
2. Trigger
3. Front handle
4. Cord retainer
5. Pivoting button
6. Upper shaft
7. Lower shaft
8. Safety guard
9. Cutting line
10. Cut-off blade
11. Spool cover
12. Eyelet
13. Spool cover lock button
14. Bump head
15. Spool
SYMBOLS ON THE PRODUCT
Read and understand all instructions before operating the product, follow all warnings and safety instructions.
Keep hands away from cut-off blade
Class II tool, double insulation
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.
Conforms to all regulatory standards in the country in the EU where the product is purchased.
EurAsian Conformity Mark
Guaranteed sound power level
96
The following signal words and meanings are intended to explain the levels of risk associated with this product:
The following signal words and meanings
is 96 dB.
Page 7
are intended to explain the levels of risk associated with this product.
DANGER
Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury.
WARNING
Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
CAUTION
Without safety alert symbol Indicates a situation that may result in
property damage.
SYMBOLS IN THIS MANUAL
Connect to power outlet.
Disconnect from power outlet.
Parts or accessories sold separately
Note
Warning
Page 8
x 1
x 2x 1x 1
x 1
x 1
Page 9
1
23
4
5
6
7
10
11
12 13
8
9
14 15
Page 10
1 2
5 6
2
1
3
Page 11
1
2
3
1
2
3 4
7 8
Page 12
p.11
p.15
10
p.14 p.16
Page 13
11
Page 14
1
1
2
2
12
Page 15
1
2
3
13
Page 16
1
1
2
2
3
14
3
1
2
3
4
1
2
Page 17
1
2
15
Page 18
1
2
16
20151118v1
Page 19
PRODUCT SPECIFICATIONS
Electric Line Trimmer
Rated power
Rated voltage 230-240V ~ 50Hz
No-load speed 12,000 min
Cutting line diameter 1.2 mm
Cutting capacity 23 cm
Vibration level (in accordance with EN 786 Annex D)
Rear handle
Front handle 3.2 m/s
Uncertainty of measurement 1.5 m/s
Noise emission level (in accordance with EN 786 Annex E)
300 W
5.5 m/s
2
2
2
-1
A-weighted sound pressure level at operator’s position
80.5 dB(A)
Uncertainty of measurement 2.5 dB
A-weighted sound power level 93.7 dB(A)
Uncertainty of measurement 1.09 dB
Weight 1.4 kg
REPLACEMENT PART
1.2 mm complete spool RAC118 (5132002590)
1.2 mm spool (3 pcs) RAC119 (5132002591)
Page 20
GUARANTEE
In addition to any statutory rights resulting from the purchase, this product is covered by a guarantee as stated below.
1. The guarantee period is 24 months for consumers and commences on the date when the product was purchased. This date has to be documented by an invoice or other proof of purchase. The product is designed and dedicated to consumer and private use only. So there is no guarantee provided in case of professional or commercial use.
2. There is, in some cases (i.e. promotion, range of tools), a possibility to extend the warranty period over the period described above using the registration on the www.ryobitools.eu website. The eligibility of the tool is clearly displayed in stores and/or on packaging. The end user needs to register his/her newly-acquired tools online within 8 days from the date of purchase. The end user may register for the extended warranty in his country of residence if listed on the online registration form where this option is valid. Furthermore, end users must give their consent to the storage of the data which are required to enter online and they have to accept the terms and conditions. The registration confirmation receipt, which is sent out by e-mail, and the original invoice showing the date of purchase will serve as proof of the extended warranty. Your statutory rights remain unaffected.
3. The guarantee covers all defects of the product during the warranty period due to defaults in workmanship or material at the purchase date. The guarantee is limited to repair and/or replacement and does not include any other obligations including but not limited to incidental or consequential damages. The warranty is not valid if the product has been misused, used contrary to the instruction manual, or being incorrectly connected. This guarantee does not apply to:
any damage to the product that is the result of improper maintenanceany product that has been altered or modifiedany product where original identification (trade mark, serial number) markings have been defaced, altered or
removed
any damage caused by non-observance of the instruction manualany non CE productany product which has been attempted to be repaired by an non-qualified professional or without prior authorization
by Techtronic Industries
any product connected to improper power supply (amps, voltage, frequency)any product used with inappropriate fuel mixture (fuel, oil, percentage of oil)any damage caused by external influences (chemical, physical, shocks) or foreign substancesnormal wear and tear of spare partsinappropriate use, overloading of the tooluse of non-approved accessories or partscarburettor after 6 months, carburettor adjustments after 6 monthscomponents (parts and accessories) subject to natural wear and tear, including but not limited to bump knobs, drive
belts, clutch, blades of hedge trimmers or lawn mowers, harness, cable throttle, carbon brushes, power cord, tines, felt washers, hitch pins, blower fans, blower and vacuum tubes, vacuum bag and straps, guide bars, saw chains, hoses, connector fittings, spray nozzles, wheels, spray wands, inner reels, outer spools, cutting lines, spark plugs, air filters, gas filters, mulching blades, etc.
4. For servicing, the product must be sent or presented to a RYOBI authorized service station listed for each country in the following list of service station addresses. In some countries your local RYOBI dealer undertakes to send the product to the RYOBI service organisation. When sending a product to a RYOBI service station, the product should be safely packed without any dangerous contents such as petrol, marked with sender’s address and accompanied by a short description of the fault.
5. A repair/replacement under this guarantee is free of charge. It does not constitute an extension or a new start of the guarantee period. Exchanged parts or tools become our property. In some countries delivery charges or postage will have to be paid by the sender.
6. This guarantee is valid in the European Community, Switzerland, Iceland, Norway, Liechtenstein, Turkey and Russia. Outside these areas, please contact your authorized RYOBI dealer to determine if another warranty applies.
Page 21
AUTHORISED SERVICE CENTRES
ACD PLANT LTD
145 Southbank Road Coundon Coventry, West Midlands CV6 1FG Phone: 02476 594348 Email: danmcgunigle@acdplant.co.uk Web: www.acdplant.co.uk
CBS Power Tools Limited
Unit 4, V P Square Storeys Bar Rd, Fengate Peterborough, Cambridgeshire PE1 5YS Phone: 01733 343031 Email: steve@cbspowertools.co.uk Web: www.cbspowertools.com
C D Powertools
76 Old Road Churwell Morley, Leeds LS27 7TH Phone: 0113 2718494 Email: info@cdpowertools.co.uk Web : www.cdpowertools.co.uk
C J Sinclair Limited
44 Victoria Road St Peters Broadstairs, Kent CT10 2UG Phone: 01843 869400 Email: repairs@cjsinclairltd.co.uk Web: www.cjsinclairltd.co.uk
Powertech Ind Ltd
Unit 2C, Ellison Road Norwood Ind, Killamarsh
6KHI¿HOG6RXWK<RUNVKLUH
S21 2JG Phone: 01142 474080 Email: stores@powertech-industrial.co.uk Web: www.powertech-industrial.co.uk
RYCKO Technical Services LTD
104 Green Lane St Albans, Herts AL3 6EX Phone: 08458 678790 Email: info@ryckotechnical.com Web: www.ryckotechnical.com
ToolTech Industrial Equipment
227 E Dunhill Road, Macosquin Coleraine, Co Londonderry BT514LQ Phone: 028 70359493 Email: john@tooltech.org.uk
For an updated list of authorised service centres, visit http://uk.ryobitools.eu/header/service-and-support/service-agents.
Page 22
DECLARATION OF CONFORMITY
Techtronic Industries GmbH Max-Eyth-Straße 10, 71364 Winnenden, Germany
Herewith we declare that the product
Electric Line Trimmer Brand: Ryobi Model number: RLT3123 Serial number range: 44443501000001 - 44443501999999
is in conformity with the following European Directives and harmonized standards
2006/42/EC, 2004/108/EC, 2000/14/EC, 2005/88/EC, 2011/65/EU, EN 60335-1:2012+A11:2014, EN 60335-2-91:2003, EN 786:1996+A2:2009, EN 55014-1:2006+A1:2009+A2:2011, EN 55014-2:1997+A1:2001+A2:2008, EN 61000-3-2:2014, EN 61000-3-3:2013, EN 50581:2012
Measured sound power level: 93.7 dB(A) Guaranteed sound power level: 96 dB(A) Conformity assessment method to Annex VI Directive 2000/14/EC amended by 2005/88/EC.
The notified body involved:
6RFLpWp1DWLRQDOHGH&HUWL¿FDWLRQHWG¶+RPRORJDWLRQ1RWL¿HG%RG\
11, route de Luxembourg L-5230 Sandweiler
Andrew John Eyre (BEng, CEng, MIET) Vice President, Regulatory & Safety Winnenden, Apr. 9, 2015
Authorised to compile the technical file: Alexander Krug, Managing Director Techtronic Industries GmbH Max-Eyth-Straße 10, 71364 Winnenden, Germany
Page 23
Page 24
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
Loading...