RLT1830LiX4
RLT1830Li13
OLT1830
ORIGINAL INSTRUCTIONS
18V ONE+ Line Trimmer
Important!
It is essential that you read the instructions in this manual before operating
this machine.
Subject to technical modifications.
9
11
10
12
13
13
12
Fig. 1
4
2
1
9
35678
Fig. 2
Fig. 3
6
15
3
1
Fig. 4
16
4
14
Fig. 5
Fig. 6
Fig. 7
17
Fig. 8
1819
Fig. 9
Fig. 10
Fig. 11
23
24
25
21
22
11
8
15
5
Fig. 12
22
26
Fig. 13
Fig. 14
Fig. 15
Safety
GENERAL SAFETY WARNINGS
WARNING
When using electric gardening appliances, basic safety
precautions should always be followed to reduce the risk
of fire, electric shock and personal injury.
Read all instructions before attempting to operate the
product and save these instructions.
■ For safe operation, read and understand all instructions
before using this product. Follow all safety instructions.
Failure to follow all safety instructions listed below, can
result in serious personal injury.
■ Do not allow children or untrained individuals to use this
unit.
■ Check the work area before each use. Remove all
objects such as rocks, broken glass, nails, wire, or
string which can be thrown or become entangled in the
machine.
■ Always wear eye protection with side shields marked to
comply with standards. Following this rule will reduce
the risk of serious personal injury.
■ Use Safety Glasses – Always wear safety glasses
with side shields. Everyday glasses have only impact
resistant lenses. They are NOT safety glasses.
Following this rule will reduce the risk of eye injury.
■ Protect your lungs. Wear a face or dust mask if the
operation is dusty. Following this rule will reduce the
risk of serious personal injury.
■ Dress Properly – Use of rubber gloves and substantial
footwear is recommended when working outdoors.
Wear heavy, long pants, long sleeves, boots, and
gloves. Do not wear loose fitting clothing, short pants,
sandals, or go barefoot. Do not wear jewellery of any
kind.
■ Secure long hair above shoulder level to prevent
entanglement in moving parts.
■ Keep children away - Keep all bystanders, children, and
pets at least 15m away.
■ Stay alert - Do not operate this unit when you are
tired, ill, or under the influence of alcohol, drugs, or
medication.
■ Do not operate in poor lighting.
■ Keep all parts of your body away from any moving part.
■ Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases, or
dust. Power tools create sparks which may ignite the
dust or fumes.
■ Avoid body contact with grounded surfaces such as
pipes, radiators, ranges, and refrigerators. There is an
increased risk of electric shock if your body is grounded.
■ Avoid Dangerous Environments - Don’t expose
appliance or line trimmer to rain or wet conditions. Water
entering an appliance or line trimmer will increase the
risk of electric shock.
■ Use Right Appliance - Do not force tool. Use the correct
tool for your application. The correct tool will do the job
better and safer at the rate for which it is designed.
■ Don’t Force Appliance – It will do the job better and with
less likelihood of a risk of injury at the rate for which it
was designed.
■ Do not operate the equipment while barefoot or when
wearing sandals or similar lightweight footwear. Wear
protective footwear that will protect your feet and
improve your footing on slippery surfaces.
■ Do not over-reach. Keep firm footing and balance.
Over-reaching can result in loss of balance.
■ Avoid accidental starting. Be sure switch trigger is in
the locked or off position before inserting battery pack.
Carrying tools with your finger on the switch trigger or
inserting the battery pack into a tool with the switch on
invites accidents.
■ Do not use tool if switch trigger does not turn it on or off.
Any tool that cannot be controlled with the switch trigger
is dangerous and must be repaired.
■ Disconnect battery pack from the appliance before
storing, servicing, or changing accessories such as
cutting line. Such preventative safety measures reduce
the risk of starting the tool accidentally.
■ Use only identical manufacturer’s replacement parts
and accessories. Use of any other parts may create a
hazard or cause product damage.
■ Maintain appliance with care - Replace trimmer head
if cracked, chipped or damaged in any way. Be sure
the trimmer head is properly installed and securely
fastened. Failure to do so can cause serious injury.
Keep handles dry, clean and free from oil and grease.
■ Check for damaged parts. Before further use of the tool,
any part that is damaged should be carefully checked
to determine that it will operate properly and perform its
intended function. Check for alignment of moving parts,
binding of moving parts, breakage of parts, mounting,
and any other conditions that may affect its operation. A
guard or other part that is damaged should be properly
repaired or replaced by an authorized service dealer.
■ Make sure all guards, straps, deflectors and handles
are properly and securely attached.
■ Use only the manufacturer’s replacement line in the
cutting head. Do not use any other cutting attachment,
for example, metal wire, rope, or the like. To install any
other brand of cutting head to this line trimmer can
result in serious personal injury.
■ Never operate unit without the grass deflector in place
and in good condition.
■ Maintain a firm grip on both handles while trimming.
Keep line trimmer head below waist level. Never cut
with the line trimmer head over 70cm or more above
the ground.
■ Store idle appliances indoors - When not in use, line
trimmer should be stored indoors in a dry, locked place
1
Safety
out of the reach of children.
■ Never use blades, flailing devices, wire or rope. Unit
is designed for line trimmer use only. Use of any other
accessories or attachments will increase the risk of
injury.
■ Inspect area to be cut. Remove objects (rocks, broken
glass, nails, wire, string, etc.) which can be thrown or
become entangled in cutting head.
■ Keep the air vents clean and free of debris to avoid
overheating the motor. Clean after each use.
■ Stop the unit and disconnect the power source when
not in use. Carry the unit with the motor stopped.
■ Store out of the reach of children.
■ Do not hang unit so that the switch trigger is depressed.
■ Battery tools do not have to be plugged into an electrical
outlet; therefore, they are always in operating condition.
Be aware of possible hazards when not using your
battery tool or when changing accessories. Following
this rule will reduce the risk of electric shock, fire, or
serious personal injury.
■ Do not charge battery tool in rain, or damp or wet
location. Following this rule will reduce the risk of
electric shock.
■ Do not use battery-operated appliance in rain.
■ Remove or disconnect battery before servicing,
cleaning or removing material from the gardening
appliance.
■ Use battery only with charger listed. For use with 18V
nickel-cadmium and lithium-ion battery packs.
■ Do not dispose of the batteries in a fire. The cell may
explode. Check with local codes for possible special
disposal instructions.
■ Do not open or mutilate the batteries. Released
electrolyte is corrosive and may cause damage to the
eyes or skin. It may be toxic if swallowed.
■ Do not place battery tools or their batteries near fire or
heat. This will reduce the risk of explosion and possibly
injury.
■ Batteries can explode in the presence of a source
of ignition, such as a pilot light. To reduce the risk of
serious personal injury, never use any cordless product
in the presence of open flame. An exploded battery
can propel debris and chemicals. If exposed, flush with
water immediately.
■ Do not crush, drop or damage battery pack. Do not use
a battery pack or charger that has been dropped or
received a sharp blow. A damaged battery is subject to
explosion. Properly dispose of a dropped or damaged
battery immediately.
■ Exercise care in handling batteries in order not to short
the battery with conducting materials such as rings,
bracelets, and keys. The battery or conductor may
overheat and cause burns.
■ For best results, your battery tool should be charged in
a location where the temperature is more than 10°C but
less than 37˚C. To reduce the risk of serious personal
injury, do not store outside or in vehicles.
■ Under extreme usage or temperature conditions,
battery leakage may occur. If liquid comes in contact
with your skin, wash immediately with soap and water,
then neutralize with lemon juice or vinegar. If liquid gets
into your eyes, flush them with clean water for at least
10 minutes, then seek immediate medical attention.
Following this rule will reduce the risk of serious
personal injury.
■ Save these instructions. Refer to them frequently and
use them to instruct others who may use this power
tool. If you loan someone this power tool, loan them
these instructions also.
WARNING
Injuries may be caused, or aggravated, by prolonged
use of a tool. When using any tool for prolonged periods,
ensure you take regular breaks.
ADDITIONAL SAFETY RULES
WARNING
The product is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the product by a person responsible
for their safety.
Children should be supervised to ensure that they do not
play with the product.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps
or tape. Do not transport batteries that are cracked or
leaking. Check with the forwarding company for further
advice.
INTENDED USE
This product is only intended for use outdoors. The product
is designed for cutting grass and light weeds only in private
garden areas.
Line trimmer
The product is intended for cutting long grass, pulpy weed,
brush and similar vegetation at or about ground level.
Edger
2
Safety
The product is intended for cutting neat edges to grass
lawns.
The product should not be used to cut or trim hedges,
bushes or other vegetation where the cutting plane is not
parallel to the ground surface.
FEATURES
KNOW YOUR PRODUCT
See Figure 1.
The safe use of this product requires an understanding of
the information on the tool and in this operator’s manual
as well as a knowledge of the project you are attempting.
Before use of this product, familiarize yourself with all
operating features and safety rules.
ADJUSTABLE FRONT HANDLE
The front handle assembly can be adjusted for ease of
operation and to help prevent loss of control.
EDGER GUIDE
The edger guide allows the line trimmer to perform as an
edger.
GRASS DEFLECTOR
The trimmer includes a grass deector that helps protect
from ying debris.
GRIPZONE™ OVERMOLD
GripZone™ overmold provides added user comfort.
LOCK-OUT BUTTON
The lock-out button prevents accidental starting.
ROTATING REAR HANDLE
The rotating rear handle can be locked in two different
positions for ease of use when edging and trimming.
TELESCOPING BOOM
The line trimmer can be adjusted to different extension
points for ease of use.
THREE-POSITION PIVOTING HEAD
The trimmer head can be adjusted with the pivot button.
ASSEMBLY
UNPACKING
This product requires assembly.
■ Carefully remove the product and any accessories from
the box. Make sure that all items listed in the packing
list are included.
WARNING
Do not use this product if any parts on the Packing List
are already assembled to your product when you unpack
it. Parts on this list are not assembled to the product by
the manufacturer and require customer installation. Use
of a product that may have been improperly assembled
could result in serious personal injury.
Inspect the product carefully to make sure no breakage or
damage occurred during shipping.
■ Do not discard the packing material until you have
carefully inspected and satisfactorily operated the
product.
■ If any parts are damaged or missing, please call Ryobi
Customer Service for assistance:
AUS: 1300 361 505
NZ: 0800 279 624
PACKING LIST
Line Trimmer
Grass Deector Assembly with Screws
Front Handle Assembly
Operator’s Manual
Battery (for RLT1830LiX4 and RLT1830Li13 only)
Charger (for RLT1830LiX4 and RLT1830Li13 only)
WARNING
If any parts are damaged or missing do not operate this
product until the parts are replaced. Use of this product
with damaged or missing parts could result in serious
personal injury.
WARNING
Do not attempt to modify this product or create
accessories not recommended for use with this product.
Any such alteration or modification is misuse and could
result in a hazardous condition leading to possible
serious personal injury.
WARNING
To prevent accidental starting that could cause serious
personal injury, always remove the battery pack from the
product when assembling parts.
DESCRIPTION
Figure 1
1. Switch trigger
2. GripZone™ overmold
3. Lock-out button
4. Adjustable front handle
5. Rear handle
3
Safety
6. Telescoping boom
7. 3-Position pivoting head
8. Edger guide
9. Grass deector
Figure 2
9. Grass deector
10. Head spool cover
11. Line cut-off blade
Figure 3
12. Screw holes
13. Screws
Figure 4
1. Switch trigger
3. Lock-out button
Figure 5
14. Latches
Figure 6
6. Telescoping boom
15. Locking coupling
Figure 7
16. Knob
Figure 8
17. Pivot button
Figure 11
18. Line release button
19. Line
Figure 12
5. Rotating rear handle
8. Edger guide
11. Line cut-off blade
15. Locking coupling
Figure 14
21. Spool retainer
22. Spool
23. Spool retainer lock buttons
24. Slots
25. Eyelet
Figure 15
22. Spool
26. Slot
ATTACHING GRASS DEFLECTOR
See Figure 2-3.
WARNING
The line cut-off blade on the grass deflector is sharp.
Avoid contact with the blade. Failure to avoid contact can
result in serious personal injury.
■ Fit the grass deflector into the slots on trimmer head.
■ Line up the screw holes in the grass deflector with the
holes in the trimmer head.
■ Install supplied screws and tighten by turning clockwise
with a Phillips screwdriver.
4
OPERATION
WARNING
Do not allow familiarity with products to make you
careless. Remember that a careless fraction of a second
is sufficient to inflict serious injury.
WARNING
Always wear eye protection with side shields marked to
comply with standards. Failure to do so could result in
objects being thrown into your eyes resulting in possible
serious injury.
WARNING
Never use blades, flailing devices, wire, or rope on this
product. Do not use any attachments or accessories not
recommended by the manufacturer of this product. The
use of attachments or accessories not recommended
can result in serious personal injury.
This product will accept Ryobi One+ 18V lithium-ion battery
packs and Ryobi One+ 18V nickel-cadmium battery packs.
For complete charging instructions, refer to the Operator’s
Manuals for your Ryobi One+ battery pack and charger
models.
NOTE: To avoid serious personal injury, always remove
the battery pack and keep hands clear of the lock-out
button when carrying or transporting the tool.
STARTING/STOPPING THE LINE TRIMMER
See Figure 4.
■ To start the line trimmer, push the lock-out button to
either the right or left side and pull the switch trigger.
■ To stop the line trimmer, release the switch trigger.
TO INSTALL BATTERY PACK
See Figure 5.
■ Insert the battery pack into the product as shown.
■ Make sure the latches on each side of the battery pack
snap into place and the battery pack is secured before
beginning operation.
TO REMOVE BATTERY PACK
See Figure 5.
■ Depress the latches on each side of the battery pack.
■ Remove the battery pack.
TELESCOPING BOOM
See Figure 6.
The boom can be extended or shortened for ease of use.
■ Remove the battery pack.
■ Loosen the telescoping boom locking coupler by turning
it counterclockwise. Slide the boom to the desired
Safety
position.
■ Tighten the coupler by turning clockwise. Make sure
the boom is securely tightened before reinstalling the
battery pack.
ADJUSTABLE FRONT HANDLE
See Figure 7.
The angle of the front handle can be adjusted 180°.
■ Remove the battery pack.
■ Loosen and remove the wing bolt from the handle.
■ Install the handle on the rear handle pole in the area
indicated by the illustration.
■ Adjust handle up or down, if necessary, to desired
operating position.
■ Reinstall the wing bolt. Tighten wing bolt to secure.
THREE-POSITION PIVOTING HEAD
See Figure 8.
The trimmer head can be adjusted to three different
positions.
■ Remove the battery pack.
■ Depress the pivot button and move the trimmer head
up or down to one of the three positions indicated by
the notches.
NOTE: Adjust the trimmer head to the rst and second
notches for trimming and edging. Adjust to the third notch
for storage only.
■ Make sure the trimmer head is securely locked into
place before reinstalling the battery pack.
OPERATING THE TRIMMER
See Figure 9.
Follow these tips when using the line trimmer:
■ Hold the trimmer with your right hand on the rear handle
and your left hand on the front handle.
■ Keep a firm grip with both hands while in operation.
■ Trimmer should be held at a comfortable position with
the rear handle about hip height.
■ Cut tall grass from the top down. This will prevent grass
from wrapping around the boom housing and line head
which may cause damage from overheating.
If grass becomes wrapped around the cutting head:
■ Remove the battery pack from the trimmer.
■ Remove the grass
WARNING
Always hold the line trimmer away from the body keeping
clearance between the body and the line trimmer. Any
contact with the line trimmer cutting head while operating
can result in serious personal injury.
CUTTING TIPS
See Figure 10.
■ Keep the trimmer tilted toward the area being cut; this is
the best cutting area.
■ The line trimmer cuts when passing the unit from left
to right. This will avoid throwing debris at the operator.
Avoid cutting in the dangerous area shown in figure 10.
■ Use the tip of the line to do the cutting. Do not force
cutting head into uncut grass.
■ Do not allow cutting head to contact the ground.
■ Wire and picket fences cause extra line wear, even
breakage. Stone and brick walls, curbs, and wood may
wear cutting line rapidly.
■ Avoid trees and shrubs. Tree bark, wood moldings,
siding, and fence posts can easily be damaged by the
line.
ADVANCING LINE
NOTE: The trimmer is equipped with an auto-feed head.
Bumping the head to try to advance the line will damage the
trimmer and void the warranty.
■ With the trimmer running, release the switch trigger.
■ Wait several seconds till the head almost stops turning,
and press the switch trigger.
NOTE: The line will extend approximately 6mm. With each
stop and start of the switch trigger until the string reaches
the length of the grass deector cut-off blade.
■ Resume trimming.
ADVANCING THE LINE MANUALLY
See Figure 11.
■ Remove the battery pack.
■ Push the black button located on the cutting head while
pulling on line to manually advance the length.
LINE CUT-OFF BLADE
See Figure 12.
This trimmer is equipped with a line cut-off blade on the
grass deector. For best cutting, advance line until it is
trimmed to length by the line cut-off blade. Advance line
whenever you hear the engine running faster than normal,
or when trimming efciency diminishes. This will maintain
best performance and keep line long enough to advance
properly.
ROTATING REAR HANDLE
See Figure 12.
The rotating rear handle is used in combination with the
edger guide.
■ Remove the battery pack.
■ Push down on the edging coupler and turn handle end
clockwise until the edging coupler locks into place.
■ Release the edging coupler.
EDGING
See Figures 12 - 13.
■ Remove the battery pack.
5
Safety
Rotate the shaft when using the edger guide for edging
sidewalks and walkways. To use the edger guide, ip down
from its stored position.
Always hold the line trimmer away from the body keeping
clearance between the body and the line trimmer. Any
contact with the line trimmer cutting head while operating
can result in serious personal injury.
WARNING
When servicing, use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
WARNING
Always wear eye protection with side shields marked to
comply with standards. Failure to do so could result in
objects being thrown into your eyes resulting in possible
serious injury.
WARNING
To avoid serious personal injury, always remove the
battery pack from the tool when cleaning or performing
any maintenance.
GENERAL MAINTENANCE
Before each use, inspect the entire product for damaged,
missing, or loose parts such as screws, nuts, bolts, caps,
etc. Tighten securely all fasteners and caps and do not
operate this product until all missing or damaged parts are
replaced. Please call Ryobi Customer Service or contact an
authorized service center for assistance.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc
WARNING
Do not at any time let brake fluids, gasoline, petroleum
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken or
destroy plastic which may result in serious personal
injury.
Only the parts shown on the parts list are intended to be
repaired or replaced by the customer. All other parts should
be replaced at an Authorized Service Center.
BATTERY PACK REMOVAL AND PREPARATION FOR
RECYCLING
WARNING
Upon removal, cover the battery pack’s terminals with
heavy-duty adhesive tape. Do not attempt to destroy
or disassemble battery pack or remove any of its
components. Lithium-ion and nickel-cadmium batteries
must be recycled or disposed of properly. Also, never
touch both terminals with metal objects and/or body
parts as short circuit may result. Keep away from
children. Failure to comply with these warnings could
result in fire and/ or serious injury.
SPOOL REPLACEMENT
See Figure 14.
Use original manufacturer’s replacement spool.
■ Remove the battery pack.
■ Push in tabs on side of spool retainer.
■ Pull spool retainer up to remove.
■ Remove the old spool.
■ To install the new spool, make sure the line is captured
in the slot on the new spool. Make sure the end of the
line is extended approximately 15cm. beyond the slot.
■ Install the new spool so that the line and slot align with
the eyelet in the cutting head. Thread the line into the
eyelet.
■ Pull the line extending from the cutting head so the line
releases from the slot in the spool.
■ Reinstall the spool retainer by depressing tabs into slots
and pushing down until spool retainer clicks into place.
LINE REPLACEMENT
See Figure 14-15.
■ Use only round type 1.65mm monofilament line.
■ Remove the battery pack.
■ Remove the spool from the cutting head.
NOTE: Remove any old line remaining on the spool.
■ Cut a piece of line approximately 2.7m long. Use only
1.65mm monofilament line.
■ Insert the line into the anchor hole in the upper part of
the spool. Neatly (do not cross) wind the line around
the upper part of the spool clockwise, as shown by the
arrows on the spool. Place line in the slot on upper
spool flange, leaving about 15cm extended beyond
the slot. Do not overfill. After winding the line, there
should be at least 6mm between the wound line and the
outside edge of the spool.
■ To replace the plastic retainer, spool, and the spool
retainer, refer to Spool Replacement earlier in this
manual.
STORING THE TRIMMER
■ Remove the battery pack from the line trimmer before
storing.
■ Clean all foreign material from the trimmer.
6
Safety
■ Store it in a place that is inaccessible to children.
■ Keep away from corrosive agents such as garden
chemicals and de-icing salts.
ENVIRONMENTAL PROTECTION
Recycle raw materials instead of disposing
of as waste. The machine, accessories
and packaging should be sorted for
environmental-friendly recycling.
SYMBOL
Safety alert
Please read the instructions carefully
before starting the machine.
Wear ear protection.
Wear eye protection.
Beware of thrown or ying objects. Keep
all bystanders at least 15 m away.
Beware of thrown or ying objects.
Keep bystanders a safe distance away
from the machine.
WARNING:
CAUTION:
CAUTION:
Indicates a potentially
hazardous situation, which,
if not avoided, could result in
death or serious injury.
Indicates a potentially
hazardous situation, which,
if not avoided, may result in
minor or moderate injury.
(Without Safety Alert Symbol)
Indicates a situation that may
result in property damage.
Do not install or use any type of blade
on a product displaying this symbol.
Avoid using in wet or damp conditions.
96
The following signal words and meanings are intended
to explain the levels of risk associated with this product.
SYMBOL SIGNAL MEANING
20131007v3
Guaranteed sound power level.
Waste electrical products should not
be disposed of with household waste.
Please recycle where facilities exist.
Check with your Local Authority or
retailer for recycling advice.
Indicates an imminently
DANGER:
hazardous situation, which,
if not avoided, will result in
death or serious injury.
7
PRODUCT SPECIFICATIONS
Model
Voltage
Cutting capacity
Cutting line diameter
Weight (without battery)
RLT1830LiX4 /
RLT1830Li13 / OLT1830
18 Volts
305 mm
1.65 mm
2.3 kg
BATTERY AND CHARGER
Model
Battery pack RB18L40 RB18L13 Not included
Charger BCL14181H BCL14181H Not included
Compatible
battery packs
Compatible
charger
RLT1830LiX4 RLT1830Li13 OLT1830
ABP1801 / ABP1802 / BPL-1820 / BPL-1815 /
BPL-1820G / RB18L13 / RB18L15 / RB18L26
/ RB18L40
BCL-1800 / BCL1418 / BCL14181H / BCL14183H
(for all compatible battery packs)
ACR-1800
(only for ABP1801 / ABP1802)
TROUBLESHOOTING
Problem Possible cause Solution
Line is welded to itself. Lubricate with silicone spray.
Line will not advance when using the
auto-feed head:
Grass wraps around boom
housing and cutting head
Motor fails to start when switch
trigger is depressed.
Not enough line on spool.
Line is worn too short. Pull line while pressing button.
Line is tangled on spool. Remove line from spool and rewind. Refer to Line
Cutting tall grass at ground level. Cut tall grass from the top down to prevent wrapping.
Battery is not secure. To secure the battery pack, make sure the latches on
Battery is not charged.
Install more line. Refer to Line replacement earlier in
this manual.
Replacement earlier in this manual.
each side of the battery pack snap into place.
Charge the battery pack according to the instructions
included with your model.
Techtronic Industries (Australia) Pty. Ltd.
Level 1, 660 Doncaster Road
Doncaster, VIC 3108, Australia
Techtronic Industries New Zealand Ltd.
18-26 Amelia Earhart Avenue
Mangere, Auckland 2022, New Zealand
960994012-04
Loading...