RUNCAM
MicroSwift 3
USER MANUAL
OSD Menu
16.8V RUNCAM
01:08
· ·
QUICK SETTINGS
Quick settings:
·
· Long press UP button for three seconds to access
to the OSD setting‘s screen
·
· Long press LEFT button for three seconds to
calibrate the voltage. When the voltage text
flashes, press UP/DOWN button to adjust it
·
· Long press DOWN button for ten seconds to reset
OSD settings to default
·
· Long press RIGHT button for three seconds to
switch between the camera presets
·
· CLR: clear the ID character;
·
· ALARM: low voltage warning value, smartly judge
the warning value of the battery when it's low; if set
it manually, then it saves the manual preset value;
·
· SCENE: switch the camera presets among Personal
/ Lightrax / Outdoor/ Indoor/ Cloudy / Twilight
·
· Press the middle button to switch ON / OFF, then
move to POS to enter the position adjustment..
RUNCAM_CLR
RSTUVWXYZ=/&:.
OSD Menu
1234567890ABC
DEFGHIJKLMNOPQ
ALARM
SCENE
SYSTEM
PILOT
TIMER
VOLTAGE
HORIZON
EXIT
: 11.1V
: PERSONAL
: ON
: ON
: ON
: ON
: OFF
POS
POS
POS
POS
POS
Camera Menu
· · LANGUAGE (English/中文)
·
· DPC (Cover the lens then press enter key)
·
· SHUTTER
(AUTO / 50-100000 / FLK)
· · BRIGHTNESS (50 / 0-255)
·
· AGC (OFF / LOW / MIDDLE / HIGH)
·
·
EXPOSURE
· ·
MAIN MENU
· · WHITE BAL (ATW1 / ATW2 / AWC→ SET /
MANUAL: MANUAL)
·
· DWDR (ON: 63 0-63 / OFF)
EXPOSURE
SHUTTER
BRIGHTNESS 050
AGC
DWDR
RETURN
AUTO
OFF
RET
ON
PERSONAL MENU
EXPOSURE
WHITE BAL
BACKLIGHT
DAY＆NIGHT
DPC
IMAGE ADJ
LANGUAGE
RESET
EXIT
AT W1
OFF
ENGLISH
COLOR
Model
Image Sensor
Horizontal Resolution
Lens
Signal System
S/N Ratio
Electronic Shutter Speed
Auto Gain Control (AGC)
One Touch Scene Setting
Min. Illumination
WDR
DNR
Day/Night
Power
Remote Control
Net Weight
Dimensions
RunCam Micro Swift 3
1/3" SONY Super HAD II CCD
600TVL
2.1mm (M12) FOV165° / 2.3mm(M12) FOV 150°
2.1mm (M8) FOV160° / 2.3mm(M8) FOV 145°
PAL/NTSC
Integrated OSD
Yes
>60dB (AGC OFF)
Yes
Personal / Lightrax / Outdoor / Indoor / Cloudy / Twilight
0.01Lux@1.2F
PAL: 1/50~100,000; NTSC: 1/60~100,000
D-WDR
2DNR
Color/Auto/B&W
DC 5-36V
Flight Controllers : BetaFlight 3.3 / ButterFlight 3.4 / Cleanflight 2.2
Working Current
60mA@12V / 120mA@5V
9g(2.3mm) / 11g(2.1mm) / 5.6g(M8)
19mm*19mm*25mm (M12) / 19mm*19mm*19mm(M8)
Parameters
IMAGE ADJ
LENS SHAD
2DNR
MIRROR
FONT COLOR
CONTRAST
SHARPNESS
DISPLAY
NEG IMAGE
RETURN
OFF
OFF
OFF
110
026
USER
OFF
· ·
IMAGE ADJ
· · LENS SHAD
(OFF/ ON:22 0-255)
· · CONTRAST (110 / 0-255)
·
· SHARPNESS (26 / 0-31)
·
· DISPLAY (CRT/LCD/USER)
·
· GAMMA
(0.5 / 0.05-1.0)
· · PED LEVEL (17 / 0-63)
Camera Menu
USER ADJ.
RETURN
GAMMA
PED LEVEL
COLOR GAIN
0.50
017
RET
176
· · COLOR GAIN (176 / 0-255)
· · DAY NIGHT LEVEL (80 / 0-176)
·
·
DAY NIGHT DELAY (3 / 1-30)
·
·
NIGHT DAY LEVEL (032 / 0-255)
·
·
NIGHT DAY DELAY (1 / 1-30)
Camera Menu
· · BURST
(OFF/ON)
· · IR SMART (OFF/ON)
·
· IR LEVEL (HIGH/LOW)
·
·
DAY ＆ NIGHT（AUTO / COLOR / B&W / EXT)
D＆N AUTO
080
SEC
032
SEC
3
1
D N LEVEL
D N DELAY
N D LEVEL
N D DELAY
RETURN RET
D＆N B＆W
BURST
IR SMART
IR LEVEL
RETURN
OFF
OFF
HIGH
RET
Camera Menu
· · AREA SEL
(AREA1/AREA2)
· ·
BACKLIGHT (BLC / HLC / OFF)
· · GAIN (042 / 0-255 )
·
· HEIGHT (4 / 0-10)
· · LEVEL
(200 / 0-255)
· · MODE (ALL DAY / NIGHT ONLY )
· · WIDTH (3 / 0-9)
·
· LEFT/RIGHT (6 / 0-6)
·
· TOP/BOT TOM (10 / 0-10)
BLC
042
004
003
006
005
AREA SEL
AREA STATE
GAIN
HEIGHT
WIDTH
LEFT/RIGHT
TOP/BOTTOM
RETURN
AREA1
ON
RET
200
HLC
LEVEL
MODE
RETURN
ALL DAY
RET
2.Betaflight 3.3 or above setting
USB VCP
Identifier Configuration/MS Serial Rx Telemetry Output Sensor Input Peripherals
UART1
UART2
UART3
UART4
UART5
115200
115200
115200
115200
115200
115200
Disabled AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
Disabled
Disabled
Disabled
Disabled
Disabled
RunCam Device
Disabled
Disabled
Disabled
Disabled
AUTO
AUTO
AUTO
AUTO
AUTO
Disabled
AUTO
1.Flight controller wiring
Note: Take UART3 for example
Flight controller
TX3 RX3
RX3
TX3
TX
RX
3.Remote control
Mode-1
Connect
Operation
Disconnect
ENTER
LEFT
RIGHT
UP
DOWN
Mode-2
Connect
Operation
Disconnect
ENTER
LEFT
RIGHT
UP
DOWN
When connected, The buzzer on Flight Controller will beep for 3 times; When disconected, The buzzer on Flight Controller
will beep for 2 times only; If connected successfully, you can long press the up button to enter the OSD menu, right button
to switch preset scenes, left button to calibrate voltage and down button to reset OSD.
Loading...