Rudd RGPS-05EAUER User Manual

Download

Page 1

FORM NO. G11-495 REV. 2

Supersedes Form No. G11-495 Rev. 1

80% A.F.U.E.

✝

UPFLOW/ HORIZONTAL GAS FURNACES

The Rheem Value Series line of upflow/horizontal gas furnaces are designed for utility rooms, closets, alcoves, or attics. Because of the model’s low-profile 34 inch

[864 mm] height, the upflow model can also be used to satisfy most applications that traditionally call for a horizontal furnace.

The design is certified by CSA International.

Features

■ Unique solid door design leads to quiet operation.

■ Patented heat exchanger, constructed of both stain-

less and aluminized steel for the maximum in corrosion resistance.

■ Low profile “34 inch” [864 mm] design is lighter and eas-

ier to handle, and leaves room for optional equipment.

■ Convertible from upflow to horizontal left or right without

field conversion.

■ Left or right side gas and electric inlet connections allow

quick and simple change.

■ Direct spark ignition with remote sense, features a inte-

grated board with an electronic air cleaner hookup.

■ Prepaint galvanized steel cabinet.

■ A slow-open gas valve and a specially designed draft

inducer motor make it one of the quietest furnaces on the market today.

■ Grab-holes in doors to aid in easy door removal and

replacement.

A variety of cooling coils and plenums designed to use with Rheem Value Series gas furnaces are available as optional accessories.

✝A.F.U.E. (Annual Fuel Utilization Efficiency) calculated in accordance with Department

of Energy test procedures.

Annual Fuel Utilization Efficiency - AFUE

THIS MODEL

97%78%

HIGH

MID

82% 88%

80.0%

RGPS- SERIES

Models with Input Rates from 50,000 to 150,000 BTU/HR [15 to 44 kW]

ENER UIDE

Page 2

2 Rheem Heating, Cooling and Water Heating

STANDARD EQUIPMENT

Completely assembled and wired; induced draft; pressure switch; redundant main gas control; blower compartment door safety switch; solid state time on/time off blower control; limit control; manual shut-off valve, pressure regulator for natural and L.P. (propane) gas; transformer; direct drive multi-speed blower motor. Furnaces are equipped with cooling/heating relay and transformer (40VA) ready for air conditioning applications. (Please note: a thermostat is not included as standard equipment.) Flame sensor diagnostics.

OPTIONAL EQUIPMENT

Twinning Kit Side and bottom filter frame assembly. Return air cabinet for all sizes. NOTE: Furnace is not listed for use with fuels other than natural or L.P.

(propane) gas.

The complete terms of limited and other warranties are available at our sales office, or through local installer.

All models can be converted by a qualified Rheem distributor or local service dealer to use L.P. (propane) gas without changing burners. Factory approved kits must be used to convert from natural to L.P. (propane) gas and may be ordered as optional accessories from a Rheem parts distributor.

For L.P. (propane) operation, refer to Conversion Kit Index Form. NOTE: For natural and L.P. (propane) gas models, standard hot surface ignition is

100% safety lockout type.

WARNING

THIS FURNACE IS NOT APPROVED

OR RECOMMENDED

FOR USE IN MOBILE HOMES

Direct Spark Ignitor

In-Shot Burners

Draft Inducer Motor

Patented Heat Exchanger

Integrated

Furnace

Control

RHEEM 80% UPFLOW/HORIZONTAL GAS FURNACE

Page 3

Rheem Heating, Cooling and Water Heating 3

BEFORE PURCHASING THIS APPLIANCE, READ IMPORTANT ENERGY COST AND EFFICIENCY INFORMATION AVAILABLE FROM YOUR RETAILER.

PHYSICAL DATA AND SPECIFICATIONS

NOTES: All models are 115V, 60HZ, 1 Ph. Gas connection size for all models is 1/2

" [12 mm] N.P.T.

➀ In accordance with D.O.E. test procedures. ➁ See Conversion Kit Index Form for high altitude derate.

GA07ESGR

Heating & Cooling

Designation

E = 1100-1300(3R) G = 1500-1700(4R) J = 1900-2100(5R)

Variations

A = Standard

Cabinet

B = Wide

Cabinet

Heating Input DesignationDesign Series

S = 2nd

Design Series

Gas

Furnace

Rheem

Electric Ignition

05E 07E 10E 12E 15E

Input

BTU/HR [kW]

50,000 [15]

75,000 [22] 100,000 [28] 125,000 [37] 150,000 [44]

P = Upflow/

Horizontal MultiPositional Tier III

Electric Ignition

NOx 05N

07N 10N 12N 15N

Blower Designation [mm]

U = 11 x 6 [279 x 152] M = 11 x 7 [279 x 178] R = 11 x 10 [279 x 254]

Fuel

R = Natural Gas -

CSA -

United States

& Canada

(North American)

—

MODEL IDENTIFICATION—UPFLOW/HORIZONTAL MODELS

[ ] Designates Metric Conversions

GENERAL TERMS OF LIMITED WARRANTY

Rheem will furnish a replacement for any part of this product which fails in normal use and service within the applicable period stated, in accordance with the terms of the limited warranty.

*For Complete Details of the Limited Warranty, Including Applicable

Terms and Conditions, See Your Local Installer or Contact the Manufacturer for a Copy.

Gas Heat Exchanger Limited Warranty ......Twenty (20) Years

Conditional Parts* (Registration Required) ......Ten (10) Years

MODEL NUMBERS RGPS- SERIES

Input-BTU/Hr [kW] ➁

Heating Capacity BTU/Hr [kW] ➀

Heat Ext. Static Pressure [kPa] .10 [.025] .12 [.029] .12 [.029] .15 [.037] .15 [.037] .15 [.037] .20 [.05] .20 [.05]

Blower (D x W) [mm]

Motor H.P.–Speed– PSC Type [W]

Motor Full Load Amps 6.8 5.8 7.9 7.1 7.9 9.5 9.5 9.5

Heating Speed Med-Low Med Med Med Med Low Low Low

Cooling Speed High High High High High Med Med Med

Cooling CFM @ .5" E.S.P. (Nominal) [L/s]

Max. E.S.P. (In. W.C.) [kPa] 0.5 [.12] 0.5 [.12] 0.5 [.12] 0.5 [.12] 0.5 [.12] 0.5 [.12] 0.5 [.12] 0.5 [.12]

Temperature Rise Range °F [°C]

Max. Outlet Air Temp. °F [°C]

Approx. Shipping Weight (Lbs.) [kg]

Standard Filter (In.) [mm]

Return Air Cabinets (Opt.) RXGRFilter Size [mm]

AFUE–H.S.I. Models ➀

05EAUER 05NAUER

50,000 [15] 75,000 [22] 75,000 [22] 100,000 [29] 100,000 [29] 100,000 [29] 125,000 [37] 150,000 [44]

41,000 [12] 60,000 [18] 60,000 [18] 80,000 [23] 80,000 [23] 80,000 [23] 99,000 [29] 119,000 [35]

11 x 6

[279 x 152]

/2-4-PSC

[373]

1200 [566]

25-55

[13.9-30.6]

155

[68.3]

[39]

153/4 x 25

[400 x 635]

C14B

(2) 12 x 16

[305 x 406]

80.0% 80.0% 80.0% 80.0% 80.0% 80.0% 80.0% 80.0%

07EAMER 07NAMER

11 x 7

[279 x 178]

/2-3-PSC

[373]

1200 [566]

35-65

[19.4-36.1]

165

[73.8]

105 [48]

153/4 x 25

[400 x 635]

C17B

(2) 12 x 16

[305 x 406]

07EAMGR 07NAMGR

11 x 7

[279 x 178]

/2-3-PSC

[373]

1600 [755]

25-55

[13.9-30.6]

155

[68.3]

105 [48]

153/4 x 25

[400 x 635]

C17B

(2) 12 x 16

[305 x 406]

10EAMER 10EBRGR

11 x 7

[279 x 178]

/2-3-PSC

[373]

1200 [566]

45-75

[250-41.7]

190

[87.7]

115 [52]

153/4 x 25

[400 x 635]

C17B

(2) 12 x 16

[305 x 406]

11 x 10

[279 x 254]

/2-3-PSC

[373]

1845

[871]

30-60

[16.7-33.3]

170

[76.6]

120 [54]

191/4 x 25

[489 x 635]

C21B

(2) 20 x 16

[508 x 406]

10EBRJR 10NBRJR

11 x 10

[279 x 254]

/4-3-PSC

[560]

2060 [922]

30-60

[16.7-33.3]

170

[76.6]

120 [54]

191/4 x 25

[489 x 635]

C21B

(2) 20 x 16

[508 x 406]

12EARJR 15EARJR

11 x 10

[279 x 254]

/4-3-PSC

[560]

2115 [998]

35-65

[19.4-36.1]

180

[82.2]

140 [63]

223/4 x 25

[578 x 635]

C24B

(2) 24 x 16

[610 x 406]

11 x 10

[279 x 254]

/4-3-PSC

[560]

2080 [982]

50-80

[27.8-44.4]

190

[87.7]

150 [68]

223/4 x 25

[578 x 635]

C24B

(2) 24 x 16

[610 x 406]

Page 4

4 Rheem Heating, Cooling and Water Heating

NOTES: ➀ May require a 3" [76 mm] to 4" [102 mm] or 3" [76 mm] to 5" [127 mm] adapter.

➁ May be 0" [0 mm] with type B vent. ➂ May be 1" [25 mm] with type B vent.

Furnaces must be vented in accordance with the National Fuel Gas Code, ANSI Z223.1 and/or Can/CGA-B149 Installation Codes and in accordance with local codes.

[ ] Designates Metric Conversions

UPFLOW DIMENSIONS AND CLEARANCE TO COMBUSTIBLE MATERIAL (INCHES) [mm]

UPFLOW DIMENSIONS

MODEL

RGPS-

05 141/2 [356] 1227/32 [326] 105/8 [270] 07

10EA 171/2 [445] 1611/32 [415] 123/8 [314]

10BRGR &

10EBRJR

12 241/2 [622] 2311/32 [593] 157/8 [403] 15 241/2 [622] 2311/32 [593] 157/8 [403]

A B C D E

171/2 [445] 1611/32 [415] 123/8 [314]

211/2 [533] 1927/32 [504] 141/8 [359]

LEFT SIDE

➀

111/2 [292] 0

➀

151/2 [381]

➀

151/2 [381] 0

➀

181/2 [470] 0 0 0 1 [25] 3 [76]

➀

221/2 [559] 0 0 0 1 [25] 3 [76]

➀

221/2 [559] 0 0 0 1 [25] 3 [76]

17/8 [48] 21/2 [64] 21/2 [64]

21/2 [64]

21/2 [64] 21/2 [64]

4 [102] ➁ 3 [76] ➁ 3 [76] ➁

REDUCED CLEARANCE (IN.) [mm]

RIGHT

BACK TOP FRONT VENT

SIDE

0 1 [25] 3 [76] 0 1 [25] 3 [76] 0 1 [25] 3 [76]

6 [152] ➂ 6 [152] ➂ 6 [152] ➂

6 [152] ➂

6 [152] ➂ 6 [152] ➂

SHIP. WGTS.

(LBS.) [Kg]

85 [38.6] 105 [47.6] 115 [52.2]

120 [54.4]

140 [63.5] 150 [68] .

Page 5

Rheem Heating, Cooling and Water Heating 5

NOTES: ➀ May require a 3" [76 mm] to 4" [102 mm] or 3" [76 mm] to 5" [127 mm] adapter.

➁ May be 0" [0 mm] with type B vent. ➂ May be 1" [25 mm] with type B vent.

Furnaces must be vented in accordance with the National Fuel Gas Code, ANSI Z223.1 and/or Can/CGA-B149 Installation Codes and in accordance with local codes.

[ ] Designates Metric Conversions

HORIZONTAL DIMENSIONS

HORIZONTAL DIMENSIONS AND CLEARANCE TO COMBUSTIBLE MATERIAL (INCHES) [mm]

WARNING

THIS FURNACE IS NOT APPROVED

OR RECOMMENDED FOR HORIZONTAL

APPLICATION OR INSTALLATION

ON ITS BACK, WITH ACCESS DOORS

FACING UPWARDS.

MODEL

RGPS-

05 07

10EA 171/

10BRGR &

10EBRJR

12 241/2 [622] 2311/32 [593] 157/8 [403] 15 241/2 [622] 2311/32 [593] 157/8 [403]

A B C D E

141/2

[356]

171/2 [445] 1611/32 [415] 123/8 [314]

2 [445]

211/2 [533] 1927/32 [504] 141/8 [359]

1227/32

1611/

[326]

32 [415]

105/8

123/

[270]

8 [314]

LEFT SIDE

➀

111/2

[292]

➀

151/2 [381]

➀

151/

2 [381]

➀

181/2 [470] 0 0 0 1 [25] 3 [76]

➀

221/2 [559] 0 0 0 1 [25] 3 [76]

➀

221/2 [559] 0 0 0 1 [25] 3 [76]

17/8 21/2 [64] 21/

2 [64]

21/2 [64]

21/2 [64] 21/2 [64]

[48]

0 0 0

4 [102] ➁ 3 [76] ➁ 3 [76] ➁

REDUCED CLEARANCE (IN.) [mm]

RIGHT

BACK TOP FRONT VENT

SIDE

0 1 [25] 3 [76] 0 1 [25] 3 [76] 0 1 [25] 3 [76]

6 [152] ➂ 6 [152] ➂ 6 [152] ➂

6 [152] ➂

6 [152] ➂ 6 [152] ➂

SHIP. WGTS.

(LBS.) [Kg]

85 [38.6] 105 [47.6] 115 [52.2]

120 [54.4]

140 [63.5] 150 [68] .

Page 6

6 Rheem Heating, Cooling and Water Heating

ACCESSORIES—UPFLOW

†Filter racks are shipped without filters.

A 1" [25.4 mm] filter may be used.

*Designates “E” or “N”.

THE RXGR-C24B MUST ONLY BE INSTALLED ON THE SIDE OPPOSITE THE GAS AND ELECTRICAL CONNECTIONS.

WARNING: IMPORTANT NOTICE

A SOLID METAL BASE PLATE (SEE TABLE) MUST BE IN PLACE WHEN THE FURNACE IS INSTALLED WITH SIDE AIR RETURN DUCTS. FAILURE TO INSTALL A BASE PLATE COULD CAUSE PRODUCTS OF COMBUSTION TO BE CIRCULATED INTO THE LIVING SPACE AND CREATE POTENTIALLY HAZARDOUS CONDITIONS.

FURNACE BASE

WIDTH

SOLID BOTTOM BASE

PLATE SIZE

IN. [mm]

KIT NO. PLATE NO.

IN. [mm]

/2 [356] RXGB-D14 AE-61874-01 115/8 x 239/16 [295 x 598]

/2 [445] RXGB-D17 AE-61874-02 151/8 x 239/16 [384 x 598]

/2 [533] RXGB-D21 AE-61874-03 185/8 x 239/16 [473 x 598]

/2 [622] RXGB-D24 AE-61874-04 255/8 x 239/16 [651 x 598]

FOR HIGH ALTITUDES:

HIGH ALTITUDE OPTION CODE: U.S. & Canada –

None required for high altitudes. HIGH ALTITUDE CONVERSION KITS: U.S. & Canada –

None required for high altitudes.

80+ HIGH ALTITUDE INSTRUCTIONS CAUTION: Always follow National Fuel Gas Code (NFGC) guidelines

when converting for high altitudes. High altitude option codes are not required for these models.

However, the burner orifice size needs to be recalculated and verified at elevations above 2000 ft. See Installation Instructions for more information.

NOTE: For Canadian installations only, an optional derate (manifold

gas pressure reduction) method may be used to adjust the furnace for altitude. See Installation Instructions for more information. This optional method may NOT be used for U.S. installations.

[ ] Designates Metric Conversions

INTERNAL FILTER RACK FOR BOTTOM OR SIDE RETURN: RXGF-DA*

Each order contains (1) one box of 10 filter racks supplied without filters. *Filters available through PROSTOCK

SIDE RETURN FILTER RACK: RXGF-CA BOTTOM RETURN FILTER RACK FOR

UPFLOW APPLICATION: RXGF-CB

ACCESSORY RETURN AIR CABINETS

Return Air Cabinets may be installed on either side application except RXGR-C24B (side application must be on side opposite gas and electrical connections).

RXPF-F01 and F02

FOSSIL FUEL KIT—is for use with Rheem Value Series Heat

Pumps and air furnaces. RXPF-F02 meets TVA requirements.

RXGP-F03

TWINNING KIT—is for parallel operation requirements.

FILTER RACK FILTER SIZES† INCHES [mm]

MODEL

RGPS-

05, 07, 10EA

10EBRGR & 10EBRJR

12, 15

RXGF-CA

(SIDE)

153/4 x 25

[400 x 635]

153/4 x 25

[400 x 635]

153/4 x 25

[400 x 635]

RETURN AIR CABINETS

RXGR-C14B 141/4 RXGR-C17B 171/2 [445] (2) 12 x 16 [305 x 406] RXGR-C21B RXGR-C24B 241/2 [622] (2) 24 x 16 [610 x 406]

IN. [mm]

[356]

211/4 [533]

FILTER SIZE

IN. [mm]

(2) 12 x 16 [305 x 406]

(2) 20 x 16 [508 x 406]

Page 7

Rheem Heating, Cooling and Water Heating 7

BLOWER PERFORMANCE DATA—UPFLOW MODELS

Note: Recommended blower speeds are in bold.

[ ] Designates Metric Conversions

MODEL

NUMBER

RGPS-

SERIES

05EAUER 05NAUER

07EAMER 07NAMER

07EAMGR 07NAMGR

10EAMER

10EBRGR

10EBRJR 10NBRJR

12EARJR

15EARJR

BLOWER

SIZE

[mm]

11 x 6

[279 x 152]

11 x 7

[279 x 178]

11 x 7

[279 x 178]

11 x 7

[279 x 178]

11 x 10

[279 x 254]

11 x 10

[279 x 254]

11 x 10

[279 x 254]

11 x 10

[279 x 254]

MOTOR

H.P.

[W]

1/2

[373]

1/2

[373]

1/2

[373]

1/2

[373]

1/2

[373]

3/4

[559]

3/4

[559]

3/4

[559]

BLOWER

MED-LO

SPEED

LOW

MED-HI

HIGH

LOW

MED

HIGH

LOW

MED

HIGH

LOW

MED

HIGH

LOW

MED

HIGH

LOW

MED

HIGH

LOW

MED

HIGH

LOW

MED

HIGH

EXTERNAL STATIC PRESSURE INCHES [kPa] WATER COLUMN

.1 [.02] .2 [.05] .3 [.07] .4 [.10] .5 [.12] .6 [.15] .7 [.17]

675 [319]

950 [448]

1115 [526] 1270 [599]

1093 [563]

1241 [586]

1393 [657] 1245 [588]

1555 [734]

1810 [854] 1050 [496]

1220 [576]

1410 [665] 1295 [611]

1645 [776]

2045 [965]

1645 [776]

2045 [965] 2320 [1095]

1645 [776]

2050 [967] 2365 [1116]

1620 [765]

2010 [949] 2340 [1104]

655 [309]

930 [439]

1090 [514] 1250 [590]

1066 [503]

1212 [572]

1359 [642] 1220 [576]

1515 [715]

1755 [828] 1040 [491]

1195 [564]

1380 [651] 1275 [602]

1615 [762]

2000 [944]

1615 [762]

2000 [944] 2260 [1067]

1635 [772]

2015 [951] 2310 [1090]

1595 [753]

1985 [937] 2275 [1074]

CFM [L/s] AIR DELIVERY

635 [300]

905 [427]

1070 [505] 1225 [578]

1039 [490]

1183 [558]

1326 [626] 1195 [564]

1475 [696]

1705 [805] 1030 [486]

1160 [547]

1345 [635] 1250 [590]

1580 [746]

1955 [923]

1580 [746]

1955 [923] 2200 [1038]

1615 [762]

1980 [934] 2250 [1062]

1570 [741]

1960 [925] 2215 [1045]

610 [288]

880 [415]

1040 [491] 1200 [566]

1008 [476]

1150 [543]

1293 [610] 1165 [550]

1435 [677]

1645 [776]

990 [467]

1140 [538]

1300 [614] 1225 [578]

1550 [732]

1905 [899]

1550 [732]

1905 [899] 2130 [1005]

1590 [750]

1935 [913] 2185 [1031]

1545 [729] 1915 [904] 2145 [1012]

585 [276]

860 [406]

1015 [479] 1165 [550]

977 [461]

1118 [528]

1259 [594] 1135 [536]

1395 [658]

1585 [748]

960 [453]

1105 [522]

1255 [592] 1195 [564]

1510 [713]

1845 [871]

1510 [713]

1845 [871] 2060 [972]

1560 [736]

1885 [890] 2115 [998]

1515 [715]

1850 [873] 2080 [982]

555 [262]

830 [392]

985 [465]

1130 [533]

941 [444]

1076 [508]

1214 [573] 1105 [522]

1350 [637]

1530 [722]

920 [434]

1065 [503]

1205 [569] 1165 [550]

1465 [691]

1785 [842]

1465 [691]

1785 [842] 1985 [937]

1520 [717]

1835 [866] 2035 [960]

1480 [698]

1800 [850] 2010 [949]

520 [245]

800 [380]

945 [446]

1085 [512]

905 [427]

1033 [487]

1169 [552] 1065 [503]

1300 [614]

1470 [694]

890 [420]

1020 [481]

1150 [543] 1135 [536]

1425 [673]

1720 [812]

1425 [673]

1720 [812] 1910 [901]

1470 [694]

1775 [838] 1950 [920]

1440 [680]

1730 [816] 1940 [916]

Page 8

Before proceeding with installation, refer to installation instructions packaged with each model, as well as complying with all Federal, State, Provincial, and Local codes, regulations, and practices.

Rheem Heating, Cooling and Water Heating

P.O. Box 17010, Fort Smith, AR 72917

“In keeping with its policy of continuous progress and product improvement, Rheem reserves the right to make changes without notice.”

PRINTED IN U.S.A. 1-10 DC FORM NO. G11-495 REV. 2

Supersedes Form No. G11-495 Rev. 1