IFB-325
Portable User Station
Talent Electronics
User Manual
9350-7488-000 Rev D 12/2005
PROPRIETARY NOTICE
The RTS product information and design disclosed herein were originated by and
are the property of Telex Communications, Inc. Telex reserves all patent, proprietary design, manufacturing, reproduction, use and sales rights thereto, and to any
article disclosed therein, except to the extent rights are expressly granted to others.
COPYRIGHT NOTICE
Copyright 2005 by Telex Communications, Inc. All rights reserved. Reproduction
in whole or in part without prior written permission from Telex is prohibited.
UNPACKING AND INSPECTION
Immediately upon receipt of the equipment, inspect the shipping container and
the contents carefully for any discrepancies or damage. Should there be any,
notify the freight company and the dealer at once.
CUSTOMER SUPPORT
Technical questions should be directed to:
Customer Service Department
RTS/Telex Communication Inc.
12000 Portland Avenue South.
Burnsville, MN 55337 U.S.A.
Telephone: (800) 392-3497
Fax: (800) 323-0498
Factory Service: (800) 553-5992
Return Shipping Instructions
Customer Service Department
Telex Communications, Inc. (Lincoln, Nebraska)
Telephone: (402) 467-5321
Fax: (402) 467-3279
Factory Service: (800) 553-5992
Shipping to the Manufacturer
All shipments of products should be made via UPS Ground, prepaid (you may
request from Factory Service a different shipment method). Any shipment
upgrades will be paid by the customer. The equipment should be shipped in the
original packing carton. If the original carton is not available, use any suitable
container that is rigid and of adequate size. If a substitute container is used, the
equipment should be wrapped in paper and surrounded with at least four inches of
excelsior or similar shock-absorbing material. All shipments must be sent to the
following address and must include the Proof of Purchase for warranty repair.
Upon completion of any repair the equipment will be returned via United Parcel
Service or specified shipper, collect.
Factory Service Department
Telex Communications, Inc.
8601 East Cornhusker Hwy.
Lincoln, NE 68507, U.S.A
Attn: Service
Please include a note in the box which supplies the company name, address,
phone number, and a person to contact regarding the repair, the type and quantity
of equipment, a description of the problem and the serial number(s).
Chapter 1
Introduction and Description ......................................................................................................................3
Description and Specifications ....................................................................................................................3
General ........................................................................................................................................................3
Features .......................................................................................................................................................3
Connections and Controls ...........................................................................................................................3
Specifications ..............................................................................................................................................4
Table
of
Contents
Chapter 2
Operation ....................................................................................................................................................5
External Connections and Controls ............................................................................................................5
Internal Jumper ...........................................................................................................................................6
Chapter 3
Replacement Parts .......................................................................................................................................7
Where to Obtain Parts .................................................................................................................................7
Mechanical Parts .........................................................................................................................................7
Chapter 4
Diagrams .....................................................................................................................................................9
CHAPTER 1
Introduction and Description
Description and Specifications
General
the IFB-325 is a portable user station for use with RTS 2-wire intercom systems. The IFB-325 is a listen-only IFB belt pack
that can be used to listen to only one intercom channel.
Features
Features of the IFB-325 include:
• Powered externally, via the intercom system power supply on channel one
• Power-ON indicator
• Headset/earset jack set for 150Ω operation
• Internal jumper selection of intercom channel one or channel two (default to channel two)
Connections and Controls
The IFB-325 has the following connections and controls:
• Intercom/program volume control
• Headset connector that accepts 1/4” monaural phone plug
• Channel connector that accepts an XLR type 3-pin connector for intercom line an power input
3
Introduction and Description
Specifications
General
Channel Supplied Power Requirements
32 VDC nominal (standard RTS line), 50 to 80 mA
Environmental Requirements
Storage: -20°C to 80°C; 0% to 95% humidity, non-condensing
Operating: 0°C to 50°C; 0% to 95% humidity, non-condensing
Dimensions
3.25” (82.6mm)H x 3.5” (88.mm)W x 1.8” (45.7mm) D
Wei ght
1.0 pounds (0.45kg)
Interface Requirements
Earset
150 to 600Ω headphones
RTS Intercom Channel
Input Level: 2 Vp-p (0 dBu) nominal
Input Impedance: 200Ω ±5%
Noise Contribution
less than -60 dB on the line
Headphone Amplifier
Voltage Gain
27 ±3dB from the line
Maximum Output
165mW into 150Ω
Frequency Response
250 Hz to 8 kHz +1/-4dB
Connector Pin Configurations
Headset Connector
Type: 1/4” Monaural Plug
Sleeve: Headset audio low
Tip: Headset audio high
Intercom Channel Connectors
Type: XLR-3F
Pin 1 Common
Pin 2 Intercom Channel 1 (audio and +32 VDC input)
Pin 3 Intercom Channel 2 (audio)
4
External Connections and Controls
CHAPTER 2
Operation
1 2
3
HEADSET
FIGURE 1. IFB-325 Connections and Controls
4
IFB-325
5
NOTE: The numbers refer to the callouts in Figure 1.
1. Volume Control: Use this control to adjust the headset/earset listen level.
2. ON indicator: This LED glows green when the belt pack is connected to an intercom channel that is functioning.
3. Headset Connector: This connector accepts a wide-response headset/earset, such as the RTS Model 2233 or Model 2234,
with a 1/4” monaural phone plug.
4. Hole Plug: This hole is for future use.
5. Intercom Channel Connectors: The IFB-325 intercom channel is connected via a 3-pin female connector. The IFB-325 is
powered from the intercom system power supply and will turn ON with the intercom system.
5
Operation
Internal Jumper
The channel termination is set for operation on intercom channel two, which is compatible with other RTS equipment. If IFB operation is required on the intercom channel one, an internal jumper must be changed as described
in Table 1.
To gain access to the jumper, disconnect all power and line connections. Remove two screws from the top of
each side and two screws from the bottom of each side. The jumper location is shown in Figure 2.
C10
C18
J1
J2
J3
DS1
C12
C8
C6
R12
FIGURE 2. Internal Jumper
JUMPER
NUMBER JUMPER FUNCTION
J3 IFB Channel Selectilon
Pin 4&5 shorted: Channel one IFB
Pin 2&3 shorted: Channel two IFB
TABLE 1. Internal Jumper
DEFAULT
SETTING
Pins 2 & 3
shorted
(Channel 2)
6
CHAPTER 3
Replacement Parts
Where to Obtain Parts
Parts may be obtained directly from Telex at:
Tele x / RT S S ystems
12000 Portland Avenue South
Burnsville, MN 55337
Telephone: (800) 392-3497
Fax: (800) 323-0498
Mechanical Parts
Final Assembly
(Refer to Figure X for Item No. location
Item No. Description Part No.
1 Case, IFB-325 90607374-008
2 Top Plate 90707374-008
3Not Used
4 Circuit Board Assembly 90307477-001
5 Knot, Nylon Body 9160563-601
6 Boot, Knob 9160563-602
7 Screw, 4-40 x 0.25, Flat Head 800124-001
8 Belt Clip 91107600-00
9 Screw, 4-40 x 0.25, Pan Head 51845-038
10 Hole Plug 4501-2617-00
11 Screw, 4-40 x 0.1875, Pan Head 51845-073
12 Washer, Lock, Split, #4 50086-001
13 Valox 1303-0010-00
Final Assembly
(Refer to Figure X for Item No. location
Item No. Description Part No.
14 Loctite Superbonder BF 753
15 Label, Serial 3101001700
16 Not Used
17 Not Used
18 Screw Locking Agent 59857-000
Connector Plate Assembly
(Refer to figure X for Item No. locations)
Item No. Description Part No.
1Not Used
2 Jack, Phono,1/4” 2013001200
3 Connector, XLR-3F 40055-10
4 Connector, 4-pin 59958-004
5 Contact, Connector 59958-200
6 thru 9 Not Used
10 Connector Plate 90807374-007
11 Screw Locking Agent 59857-000
7
Replacement Parts
Circuit Board Assembly
(Refer to Figure X)
Ref No. Description Part No.
Support Bracket 64106-003
C1, C2 Capacitor, CM, SM, 0.22μF, 50V 102880-237
C3 Capacitor, CM, SM, 0.33μF, 50V 102880-239
C4 Capacitor, CM, SM, 0.1μF, 50V 102882-351
C5 Capacitor, EL, 2200μF, 16V 102884-412
C6 Capacitor, EL, 100μF, 25V 51821-626
C7 Capacitor, CM, SM, 0.01μF, 50V 102881-339
C8 Capacitor, EL, 47μF, 25V 51821-625
C9 Capacitor, CM, SM, 0.01μF, 50V 102881-339
C10 Capacitor, EL, SM, 1μF, 50V 102884-606
C11 Not Used
C12 Capacitor, EL, SM, 0.1μF, 50V 102884-600
C13 Capacitor, CM, SM, 0.1μF, 50V 102882-351
C14 Not Used
C15 Capacitor, EL, 2200μF, 25V 517004-036
C17 Capacitor, CM, SM,220 pF, 50V 102879-208
C18 Capacitor, EL, SM, 4.7μF, 25V 102884-410
C19 Not Used
C20,
C21
C22 -
C24
C25 Capacitor, EL, 2200μF, 16V 102884-412
D1 - D4 Diode, SM, Switching, 914/4148 58711-100
DS1 LED, Rectangular, Green 58685-101
J1, J2 Connector, St Locking, 0.059, M-4 59958-104
J3 Connector, St Header, 0.100, M-5 590089-005
PEM1 Nut, Self Clinching, 4-40 59832-002
PEM2 Nut, Self Clinching, 4-40 59832-002
Q1, Q2 Transistor, SM, SI NPN,
R1, R2 Resistor, SM, 22.1kΩ, 1%, 1/8W 102404-333
R3-R6 Not Used
R7 Resistor, SM, 10kΩ, 1%, 1/8W 102404-300
R8 Resistor, SM 10kΩ, 5%, 1/8Ω 102513-103
R9 Resistor, SM, 10kΩ, 1%, 1/8W 102404-300
R10 Resistor, SM, 4.7kΩ, 5%, 1/8W 102513-472
R11 Not Used
Capacitor, CM, SM, 0.1μF, 50V 102881-351
Not Used
54749-000
MMBTA13
Circuit Board Assembly
(Refer to Figure X)
Ref No. Description Part No.
R12 Potentiometer, 10kΩ, 10%, 0.05W 54131-005
R13 Resistor, SM, 10Ω, 5%, 1/8W 102513-100
R14,
R15
R16 Resistor, SM, 10Ω, 5%, 1/8W 102513-100
R17 Resistor, SM, 150kΩ, 5%, 1/8W 102513-154
R18 Resistor, SM, 10Ω, 5%, 1/8W 102513-100
R19,
R20
R21 Resistor, SM, 7.5kΩ, 5%, 1/8W 102513-752
R22 Not Used
R23 Resistor, SM 0Ω, 5%, 1/8W 102513-000
R24,
R25
R26 -
R29
R30 -
R33
R34 Resistor, SM, 1kΩ, 5%, 1/8W 102513-102
R35 Resistor, SM 75kΩ, 1%, 1/8W 102404-384
TP1 Connector, Test Point Terminal 20170014-00
U1 IC, SM, Dual Op Amp, LM833 16030833-
U2 IC SM, LP Audio Amp, MC34119 16030146-
U3 Not Used
U4 IC, Voltage Regulator, 12V, 78L12 54680-412
Resistor, SM, 47kΩ, 5%1/8W 102513-473
Not Used
Not Used
Resistor, SM, 10Ω, 5%, 1/8W 102513-100
Not Used
SM1
SM1
8
CHAPTER 4
Diagrams
Drawing Number Title
9010-7488-000 Figure X Final Assembly, IFB-325
9020-7477-001 Figure X Connector Plate Assembly, IFB-325
9030-7477-001 Figure X PC Board Assembly, IFB-325
9027-7477-001 Figure X Schematic, IFB-325
9
Diagrams
1.
3.
4.
1
2
3
4
7
8
9
( 2 PLS )
(
4 PLS )
IFB325
90007488-000
RTS
TELEX
BY
10
2.
3.
12
( 2 PLS )
14
6
1.
5
11
( 2 pls )
15
17
16
4.18
J1
J2
TO
J1
TO
J2
FIGURE 3. Final Assembly, IFB-325
9010-7488-000, Rev F
10
FIGURE 4. Connector Plate Assembly, IFB-325
9020-7477-001, Rev E
11
Diagrams
FIGURE 5. PC Board Assembly, IFB-325
9030-7477-001 Rev M
12
13
14
15
Loading...