Rough Country 588.20 User Manual

92158400

08-10 F250 6” SUSPENSION KIT

Thank you for choosing Rough Country for your suspension needs.
Rough Country recommends a certified technician installs this system. In addition to these instructions, professional

knowledge of disassemble/reassembly procedures as well as post installation checks must be known. Attempts to install
this system without this knowledge and expertise may jeopardize the integrity and/or operating safety of the vehicle.

Please read all the instructions before beginning the installation. Check the kit hardware against the parts list. Be sure
you have all the needed parts and understand where they go. Also please review the tools needed list and make sure
you have needed tools.

PRODUCT USE INFORMATION

As a general rule, the taller a vehicle is the easier it will roll. We strongly recommend seat belts and shoulder
harnesses should be worn at all times. Avoid situations where a side rollover may occur.

Braking performance and capabilities are decreased when significantly larger/heaver tires and wheels are used. Take
this into consideration while driving. Also, speedometer recalibration is necessary when larger tires are installed.

Do no add, alter, or fabricate any factory or after-market parts which increase vehicle height over the intended height of
the Rough Country product purchased. Mixing component brands, lifts, and/or combining body lift with suspension lifts
voids all warranties. Rough Country makes no claims regarding lifting devices and excludes any and all implied claims.
We will not be responsible for any product that is altered.

This kit is packaged as a leveling kit—raising the front 6” and the back 5”. If you desire a different look or if the vehicle
has a tool box or added weight in the rear, please consult with your sales representative about block / u-bolt options.

This 6” suspension system was developed for 37x12.50x17 tire on an after market wheel w/ 4.5” back spacing.

NOTICE TO DEALER AND VECHICLE OWNER

Any vehicle equipped with any Rough country product must have the “Warning to Driver” decal installed on the sun visor
or dash. The decal is to act as a constant reminder for whoever is operating the vehicle of its unique handling character­istics. INSTALLING DEALER—It is your responsibility to install the warning decal and to forward these installation in­structions on too the vehicle owner for review and to be kept in the vehicle for its service life.

Kit Contents:

9295 Diesel Coil Springs
OR
9296 Gas Coil Springs
1580Box1 Upper Control Arms
1580Box2 Adj Lower Control Arms
1584Box1 Stabilizer Drop Brackets
Track Bar Bracket
Control Arm Bracket
Sway Bar Link
Hardware Bags
Pitman Arm
Stainless Front Lines
1580Box4 Shock Box
6111 Add-a-leaf
6578 3” Block and U-Bolt Kit
OR
6539 Rear Block / u-bolt kit for
use with vehicles w/o
factory rear overloads

Tools Needed:
8mm Wrench 1 1/8” Wrench

10mm Wrench 1 13/16” Wrench
12mm Wrench Jack Stands
15mm Wrench Jack
17mm Wrench Drill
17mm Socket Drill Bits-13/16-7/8
18mm Wrench
18mm Socket
19mm Wrench
21mm Wrench
24mm Socket
30mm Socket

Torque Specs:
Size Grade 5 Grade 8
5/16” 15 ft/lbs 20 ft/lbs

3/8” 30 ft/lbs 35 ft/lbs
7/16” 45 ft/lbs 60 ft/lbs
1/2” 65 ft/lbs 90 ft/lbs
9/16” 95 ft/lbs 130 ft/lbs
5/8” 135 ft/lbs 175 ft/lbs
3/4” 185 ft/lbs 280 ft/lbs

FRONT INSTALLTION INSTRUCTIONS

1. Block the rear wheels of the vehicle. Raise the front of the vehicle and support the frame with jack stands. Remove
the front wheels and tires and set aside. Position a hydraulic jack under the front axle and raise the jack until the
front suspension begins to compress

2. Disconnect the track bar from the driver side frame bracket, using a 30mm wrench.

3. Disconnect the sway bar end links from the axle and the sway bar, using a 18mm wrench. Remove end links and
retain the hardware for reuse. See Photo 1.

4. Remove the bump stop from the cup shaped bracket. Remove the bracket from the frame rail using 10mm wrench.

See Photo 2.

Photo 1 Photo 2

5. Disconnect the ABS sensor wire from the lower spring seat and the radius arm, using a 8mm wrench.

6. Unbolt the brake line brackets from the axle, using a 10mm wrench. Remove the vacuum line from the clamp on the
axle.( If equipped with automatic hubs). Remove the stock brake line from the stock steel line and install the supplied
braided brake lines in the factory location with the factory hardware. Please note there is a driver and passenger
side brake hose . Photo 3 shows the passenger side new line being installed. Bleed bra ke system.

7. Using a 19mm wrench remove the nut, retaining washer and rubber bushing from the upper shock mounts.
18mm wrench remove the lower shock bolts. Retain hardware for re-use.

8. Carefully lower the jack until the coil springs are free. Remove the coil springs from the vehicle. Note: use of a coil
spring compressor may be required for spring removal.

9. Support both driver and passenger radius arms with jack stands. Using a 24mm wrench, and socket remove the bolt
holding the radius arm to the frame. Using a 24mm wrench, and socket remove the bolts holding the radius arm to
the axle. Retain stock hardware for reuse.

10. Insert bushings, and sleeves from kit bag into the upper control arm. See Photo 4.

Photo 3

Photo 4

Using a

Disconnect Vacuum Line (Auto Hubs only)