rotork CMA Series, CML-1500, CML-3000 Quick Start Manual

SET PT

Setpoint

THRUST or TORQUE

Thrust Display or

Ouput Torque

LOCAL/REM

Local / Remote Operation

MANJOG

Manual Jog

TORQ/THRUST C

Close Torque/Thrust

TORQ/THRUST O

Open Torque/Thrust

CL ACT

Close Action

OP ACT

Open Action

CL LIM

Close Limit (zero)

OP LIM

Open Limit (span)

CMD4

Field Command Signal4

CMD20

Field Command Signal20

DBAND

Deadband

FLTHST

Fault History Access

ADVANC

Advanced Menu

DEFLTS

Default Menu Access

STATUS

SET OUTPUT

TORQUE/TRUST

STEP 3

SET CLOSE LIMIT

OF TRAVEL

STEP 4

SET OPEN LIMIT

OF TRAVEL

STEP 5

CALIBRATE COMMAND

SIGNAL ZERO SETPOINT

STEP 6

CALIBRATE COMMAND

SIGNAL SPAN SETPOINT

STEP 2

SELECT ACTION AT END

OF TRAVEL ( LIMIT OR FORCE)

STEP 7

DEADBAND

STEP 3

SET CLOSE LIMIT

OF TRAVEL

STEP 4

SET OPEN LIMIT

OF TRAVEL

STEP 5

CALIBRATE COMMAND

SIGNAL ZERO SETPOINT

STEP 6

CALIBRATE COMMAND

SIGNAL SPAN SETPOINT

SELECT ACTION AT END

OF TRAVEL ( LIMIT OR FORCE)

STEP 7

DEADBAND

SET CLOSE LIMIT

OF TRAVEL

STEP 4

SET OPEN LIMIT

OF TRAVEL

STEP 5

CALIBRATE COMMAND

SIGNAL ZERO SETPOINT

STEP 6

CALIBRATE COMMAND

SIGNAL SPAN SETPOINT

STEP 7

DEADBAND

CAUTION: Before commissioning
actuators fitted with the Reserve
Power Pack (RPP), please ensure
PUB094-019 is fully understood and
additional safety instructions are
followed where applicable.

Ensure the local control selector is set to
LOCAL during the commissioning process.

CMA Range

Quick Start Guide

CML-1500 and CML-3000

Position Display
START POINT

POSIT

Position

CLOSE

1

STEP 1

THRSTC

OPEN

REMOTE

X

POS I T

Until

LOCAL

THRSTC or TORQ C

LOCAL

THRSTO

THRSTO or TORQ O

CLOSE

LOCAL

2

STEP 2

CL ACT

OPEN

LOCAL

OP ACT

LOCAL

or

POS I T

LOCAL

EDIT

TC 100

LOCAL

EDIT

TO 100

LOCAL

EDIT

CA LIM

LOCAL

EDIT

OA LIM

LOCAL

or

%

Select desired Torque/Thrust Close

or

%

Select desired Torque/Thrust Open

or

Select Force FRC or Limit LIM

or

Select Force FRC or Limit LIM

EDIT

TC 600

Example set at 60%

LOCAL

EDIT

TO 600

Example set at 60%

LOCAL

EDIT

CA LIM

LOCAL

EDIT

OA FRC

%

SAVE

%

SAVE

X

X

X

SAVE

X

SAVE

LOCAL

THRSTC

LOCAL

THRSTO

LOCAL

CL ACT

LOCAL

OP ACT

LOCAL

3

STEP 3

These instructions enable the actuator to be
configured to suit the valve and must be carried
out before electrical start up. For complete
instructions refer to PUB094-019.

PUB094-022-00 Issue 08/18

CL LIM

LOCAL

EDIT

CL LIM

or

Move Actuator to CLOSE Position

www.rotork.com

LOCAL

EDIT

CL LIM

SAVE

Rotork plc
Brassmill Lane, Bath, UK

tel [phone]
fax [phone]
email [e-mail]

As part of a pro cess of on-going product d evelopment, Rotork reserves t he right to amend and change specific ations without
prior notice. Publis hed data may be subject to change. For t he very latest version releas e, visit our website at www.rotork.com

The name Rotork is a reg istered trademark. Rotork recognis es all registered trademarks .
Published and prod uced in the UK by Rotork. POWTG0 818

USA
Rotork Controls

tel [phone]
fax [phone]
email [e-mail]

X

A full listing of our worldwide
sales and service network is
available on our website.

LOCAL

CL LIM

SET OPEN LIMIT

OF TRAVEL

STEP 5

CALIBRATE COMMAND

SIGNAL ZERO SETPOINT

STEP 6

CALIBRATE COMMAND

SIGNAL SPAN SETPOINT

STEP 7

DEADBAND

CALIBRATE COMMAND

SIGNAL ZERO SETPOINT

STEP 6

CALIBRATE COMMAND

SIGNAL SPAN SETPOINT

STEP 7

DEADBAND

CALIBRATE COMMAND

SIGNAL SPAN SETPOINT

STEP 7

DEADBAND

DEADBAND

CAUTION: Before commissioning
actuators fitted with the Reserve
Power Pack (RPP), please ensure
PUB094-019 is fully understood and
additional safety instructions are
followed where applicable.

Ensure the local control selector is set to
LOCAL during the commissioning process.

CMA Range

Quick Start Guide

CML-1500 and CML-3000

LOCAL

4

STEP 4

5

STEP 5

6

STEP 6

7

STEP 7

OP LIM

OPTIONAL:
Calibrate 4-20 mA Signal
using external applied
signal LOW (Zero)

OPTIONAL:
Calibrate 4-20 mA Signal
using external applied
signal HIGH (Span)

LOCAL

X

POS I T

LOCAL

CMD 4

LOCAL

CMD 20

LOCAL

DBAND

Local Control is now set

Move knob to REMOTE for REMOTE CONTROL

LOCAL

EDIT

OP LIM

LOCAL

EDIT

DB 02

Example set at 0.2%

Move Actuator to OPEN Position

%

Adjust to desired % Deadband 0-10%

or

LOCAL

EDIT

CMD 4

LOCAL

EDIT

CMD 20

or

LOCAL

EDIT

OP LIM

Apply LOW
External
mA Signal

Apply HIGH
External
mA Signal

LOCAL

EDIT

DB 1 00

Example set at 1.00%

X

SAVE

X

SAVE

X

SAVE

%

SAVE

X

LOCAL

OP LIM

LOCAL

CMD 4

LOCAL

CMD 20

LOCAL

DBAND

These instructions enable the actuator to be
configured to suit the valve and must be carried
out before electrical start up. For complete
instructions refer to PUB094-019.

PUB094-022-00 Issue 08/18

www.rotork.com

Rotork plc
Brassmill Lane, Bath, UK

tel [phone]
fax [phone]
email [e-mail]

As part of a pro cess of on-going product d evelopment, Rotork reserves t he right to amend and change specific ations without
prior notice. Publis hed data may be subject to change. For t he very latest version releas e, visit our website at www.rotork.com

The name Rotork is a reg istered trademark. Rotork recognis es all registered trademarks .
Published and prod uced in the UK by Rotork. POWTG0 818

USA
Rotork Controls

tel [phone]
fax [phone]
email [e-mail]

A full listing of our worldwide
sales and service network is
available on our website.