Roland RMP 3 Service Manual

Thank you, and congratulations on your choice of the Roland RMP-3.
Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (on another
leaflet). These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel
assured that you have gained a good grasp of every feature provided by your new unit, Owner’s manual should be read in its
entirety. The manual should be saved and kept on hand as a convenient reference.

As shipped, the RMP-3’s battery is not installed. Please read “Preparations—Loading the Battery” and follow the
instructions to install the battery.

Copyright © 2005 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form
without the written permission of ROLAND CORPORATION.

Panel Description

fig.Panel

1

2

3

8

1.

Mini Speaker

For the metronome’s beep sound only. If the
OUTPUT jack is being used, no sound is
output.

2.

[METRONOME] Button

Selects the metronome parameter.

3.

[START/STOP] Button

Starts and stops the metronome.

4.

PHONES VOLUME Knob

Adjusts the OUTPUT jack’s volume.

* The volume of the mini speaker is adjusted with CLICK

VOLUME.

5.

[COACH] Button

Selects the Coach mode.

7

9

10

6.

VALUE [+]/[-] Button

Use these buttons to change the values of
each parameter.
To increase the value rapidly, hold down [+]
and press [-]. To decrease the value rapidly,
hold down [-] and press [+].

7.

BEAT Indicator

Flashes along quarter notes.
Red indicator flashes on accent beats.

8.

Head

9.

Sensor

10.

Tuning Bolts

Adjusts the head tension.

4

5

6

– 1 –

C5100025 1RCC

2.

Side Panel

fig.Side

1

2

4

3

5

MIX IN Jack

For connecting an external audio source
(CD, MD, etc.) for playing along.

3.

OUTPUT Jack

For headphones, amp, or audio system.

* The RMP-3 outputs sounds in monaural.

1.

Security Slot ( )

http://www.kensington.com/

4.

AC Adaptor Jack

Connect the AC adaptor (optional) here.

5.

POWER Switch

Turns the power on/off.

Preparations

Loading the Battery

fig.BattCase.e_50

1.

Press down and slide off the lid of the battery compartment
(located on the bottom of the unit).

2.

Connect the snap cord to the battery, and place it inside the
battery compartment.

* Verify the battery’s polarity (+ versus -).

3.

Securely close the battery cover.

* Do not let the snap cord get caught in the battery compartment lid.

When to Change the Battery

The Battery LOW indicator ( ) at the lower left of the

display begins to flash when the battery power drops.
Insufficient battery power lowers the volume level of the mini speaker and causes unstable
operation. Replace the battery as soon as possible.

9V
Battery

Battery
Snap

Connecting the AC Adaptor

A BOSS PSA series AC adaptor (sold separately) can be used to power the RMP-3.

Turn off the power before connecting the AC adaptor.

Use only the BOSS PSA-series AC adaptor. Other adaptors may cause malfunction or damage
to the RMP-3 and must never be used.

The Battery LOW indicator ( ) flashes when the battery power drops while the AC

adaptor is used.

Adjusting the Head Tension

fig.Bolt

BEFORE playing the RMP-3, you must tune the head to your preferred
playing tension. The head is NOT tuned before shipping.
Always tighten the tuning bolts in the order shown in the figure.

* Failure to adjust the tension may result in damage to the head.

* Head tension may change with extended use. Make adjustments as needed.

– 2 –

1

8

63

45

7

2

About the Display

fig.Display.e

Count

Tempo/Value

Rhythm Type

Beat

Battery LOW Indicator

Flashes when the battery

power drops.

Tr igger Indicator

Appears when the
head is struck.

Replacing the Head

If the head has been damaged or no longer maintains correct tension, replace it.
To order replacement heads (
the unit or the nearest Roland Service Center.

The MH-8 Mesh Head is not compatible and cannot be used.

Replacing the Head

When replacing or tuning, use the included tuning key.

fig.HeadChange

1.

Remove all tuning bolts.

Gradually loosen each one in order, turning them
counterclockwise.

* Do not lose the tuning bolts.

2.

Open the case, and then remove the old head.

3.

Place the new head in the case.

4.

Securely close the case.

5.

Attach all eight tuning bolts.

6.

Adjust the tension of the head. Refer to “Adjusting the Head Tension.”

RMP-3 Mesh Head

), contact the retailer from whom you purchased

Metronome Needle

Specifications

Pad Size

8 inches

Tempo

20–260

Beat

24 types

Rhythm Types

18 types

Metronome Sounds

5

Coach Mode

Functions: 5
Exercise Variations: 20

Connectors

PHONES/OUTPUT Jack: 1
(Stereo miniature phone type)
MIX IN Jack: 1 (Miniature phone type)
AC Adaptor Jack

Power Supply

DC 9 V:
Dry Battery 6F22/1604 (9 V) type
(carbon)
Dry Battery 6LR61/1604A (9 V) type
(alkaline)
AC Adaptor

Current Draw

55 mA

* Expected battery life under continuous use:

Carbon: 2 hours
Alkaline: 6 hours

These figures will vary depending on the
actual conditions of use.

Stand Screw Size

M8

Dimensions

263 (W) x 348 (D) x 78 (H) mm
10-3/8 (W) x 13-3/4 (D) x 3-1/8 (H)
inches

– 3 –

Weight

1.2 kg / 2 lbs 11 oz (including a battery)

Accessories

Dry Battery 6F22/1604 (9 V) type
(carbon)
Tuning Key
Owner’s Manual
Leaflet (“USING THE UNIT SAFELY”
and “IMPORTANT NOTES”)

Options

AC Adaptor: BOSS PSA series
Pad Stand: PDS-2

* In the interest of product improvement, the

specifications and/or appearance of this
unit are subject to change without prior
notice.