Roland KC-220 Owner’s Manual

Owner’s Manual
Keyboard Amplier
Main features
KC-220 is a stereo keyboard amp designed for high sound quality, and is suitable for a variety of sources such as keyboards and sound modules.
5 Dual power design allows operation using eight AA batteries or the AC adaptor.
5 The KC-220 features a two-way stereo design with a speaker and a tweeter.
Speaker Output
5 The input section is equipped with a mixer. CH1 additionally provides an XLR connector that supports mic input.
5 Two types of AUX IN jack (RCA phono and stereo mini-jack) are provided for easily connecting an audio player or
other source.
5 The two-band equalizer is convenient for adjusting the character of the sound.
5 A speaker stand can be attached to allow convenient use as a monitor or small-scale PA.
5 The headphone jack is convenient for monitoring at night, etc.
30 W (15 W + 15 W)
* When using the AC adaptor.
Before using this unit, carefully read “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (the leaet “USING THE UNIT SAFELY” and the Owner’s Manual (p. 7)). After reading, keep the document(s) where it will be available for immediate reference.
Copyright © 2017 ROLAND CORPORATION
Panel Descriptions
Top Panel
Rear Panel
5 642 31
7911 10 8
Top Panel
1
[CH1]–[CH3] knobs
Adjust the volume of the devices connected to CH1–CH3.
2
[EFFECT] knob
The internal eect can be applied to the devices that are connected to CH1–CH3.
Depending on the position of the knob, it switches between two types of eects and adjusts the depth of the eect.
Eect Explanation
REVERB This eect adds reverberation to the sound.
An eect that adds a slightly modulated sound to
CHORUS
WIDE
* The eect is not applied to the sound that’s being input from
AUX IN jack.
the direct signal, creating beautiful spaciousness and depth.
This is a stereo chorus that processes the three frequency bands independently, creating a spacious, embracing eect.
The low range remains rmly localized in the center, and the sound will become more spacious as you go from the mid to the high range.
12
3
EQUALIZER
[LOW ] knob
Adjusts the sound level of the low-frequency range.
[HIGH] knob
Adjusts the sound level of the high-frequency range.
4
[MASTER] knob
Adjusts the overall volume.
* The [MASTER] knob does not adjust the signal that is output
from the LINE OUT jack.
5
PHONES jack
You can connect headphones here.
* If a plug is inserted in this jack, no sound will be output from
the unit’s own speaker. This is convenient if you don’t want loud sound to be produced from the speaker, such as when you’re practicing at night.
6
[POWER] switch
Turns the power on/o. When the power is on, the indicator at the left of this switch is lit.
* When operating on battery power only, the unit’s indicator will
become dim when battery power gets too low. Replace the battery as soon as possible.
2
Rear Panel
12
Battery case
Panel Descriptions
7
CH1–CH3 input jacks
CH1: BALANCED jack, MIC/LINE jack
CH1 is equipped with a phone-type MIC/LINE jack and a balanced XLR-type BALANCED jack that is convenient for connecting a mic.
This channel supports levels ranging from mic input level (-50 dBu) through line input level (-20 dBu) for sources such as a sound module.
* Pin assignment of CH1 BALANCED jack
CH2, CH3: LINE jacks
Use these for connecting keyboards, sound modules, and other devices.
They accept line level input (-20 dBu).
8
AUX IN (STEREO, R/L) jacks
Here you can connect an audio player, electronic musical instrument, or similar audio source, and listen to it while you perform.
[LEVEL] knob
Adjusts the level of the input from AUX IN jacks.
9
LINE OUT jack
Connect this to your mixer or recorder.
The EQUALIZER knobs and the [MASTER] knob do not aect the volume or tone of the output from the LINE OUT jack.
10
FOOT SW jack
If a momentary-type footswitch (sold separately: FS-5U) is connected here, you can use your foot to turn the internal eect on/o.
FS-5U
2 HOT 1 GND
3 COLD
Installing batteries
1. Remove the screws from these two
locations.
2. Remove the battery compartment
cover.
3. Insert batteries, taking care to
observe the correct polarity.
* We recommend that you keep batteries
installed in the unit even though you’ll be powering it with the AC adaptor. That way, you’ll be able to continue a performance even if the cord of the AC adaptor gets accidentally disconnected from the unit.
* To prevent malfunction and speaker damage, make sure to
switch o the KC-220’s power before you insert or replace its batteries, and before connecting it to other devices.
* If you handle batteries improperly, you risk explosion and
uid leakage. Make sure that you carefully observe all of the items related to batteries that are listed in “USING THE UNIT
SAFELY” and “IMPORTANT NOTES” (leaet “USING THE UNIT SAFELY” and Owner’s manual (p. 7)).
Removing the battery case
Although it is possible to replace the batteries without removing the battery case, battery replacement will be easier if you remove the battery case.
1. Remove the screws from these
two locations.
2. Remove the battery case.
* Take care that no metal object touches the contacts of the
battery case. This can short-circuit the batteries, causing the case to overheat or burn.
11
DC IN jack
Connect the included AC adaptor.
* Use only the AC adaptor that was included with
the unit.
* To prevent the inadvertent disruption of power
to your unit (should the plug be pulled out accidentally), and to avoid applying undue stress to the jack, anchor the power cord using the cord hook, as shown in the illustration.
3
Loading...
+ 5 hidden pages