Roland HPi-5 TurboStart User Manual

Download

Page 1

®ÂØÒÅˆÎ

HPi-5

digital pian o

It’s a Fact…

The HPi-5 offers a wide range of ins trument tones and displays notation/lyrics on an LCD screen built

into the music stand. The HPi-5 includes:

• 421 CD -quality GM2/© sounds

• 11 drum sets, 1 SFX Set

• 64-note polyphony

• 88-key progressive hammer action keyboard

• 30 preset pianist styles

• 16-track recorder with built-in metronome

• Reverb, Chorus, Sympathetic Resonance

• Built-in 3.5” floppy disk drive

• Music stand LCD screen with SMF lyric display

Intializing—Restoring Factory Settings

Use the following procedure to clear the internal memory and reload the factory settings:

Caution: All USER information will be lost. Be sure to back up any information you wish to keep.

1. Press the FUNCTION button (located to the left of the cursor buttons .)

2. Use the cursor [4][6] buttons to locate FACTORY RESET on the screen, then press the

ENTER button (located to the right of the cursor buttons.)

3. When “All the factory settings will be restored” appears on the screen, press the cursor [4]

button until EXECUTE is highlight ed on the screen, then press the ENTER button.

4. When “Turn the power off, then on again” appears on the screen, turn the power off and then on to complete the factory reset.

Refer to the Owner’s Manual, pg. 45 for more information.

Selecting Tones

Use the following procedure to select a tone:

1. Press a tone button (e.g. Piano, E.Piano, Organ, etc.) in the TONE section (located to the left of the cursor buttons .)

2. Use the cursor [3][4][5][6] buttons to locate a tone on the screen.

TurboStart

3. Press the EXIT button (located to the right of the cursor buttons .)

Refer to the Owner’s Manual, pg. 24 for more information.

Selecting Dual Tones

Use the following procedure to select dual tones :

1. Simultaneously press two tone buttons (e.g. Piano + Strings , E.Piano + Voice, etc.) in the TONE section (located to the left of the cursor buttons.)

2. Use the cursor [5][6] buttons to select TONE 2.

3. Press the cursor [4] button until TONE 1 is highlighted on the screen.

4. Use the cursor [5][6] buttons to select TONE 1.

5. Press the cursor [4] button until DUAL BALANCE is highlighted on the screen.

6. Use the cursor [5][6] buttons to adjust the volume balance between TONE 1 and TONE 2.

7. Press the EXIT button (located to the right of the cursor buttons .)

Refer to the Owner’s Manual, pg. 25 for more information.

Selecting Split Tones

Use the following procedure to select split tones:

1. Select a right-hand tone as described under “Selecting Tones” or “Selecting Dual Tones.”

2. Press the SPLIT button (located to the left of the cursor buttons .)

3. Use the cursor [5][6] buttons to select a LEFTHAND TONE.

4. Press the EXIT button.

5. Press the cursor [4] button until SPLIT POINT is highlighted on the screen.

6. Use the cursor [5][6] buttons to change the note at which the LEFT-HAND TONE becomes

the RIGHT-HAND TONE.

7. Press the EXIT button (located to the right of the cursor buttons .)

Refer to the Owner’s Manual, pp. 26 –27 for more information.

Page 2

®ÂØÒÅˆÎ

HPi-5

digital pian o

Selecting Pianist Styles

Use the following procedure to select a pianist style:

1. Press the PIANIST button (located to the left of the cursor buttons .)

2. Use the cursor [3][4][5][6] buttons to locate a pianist style.

3. Play a note on the lower half of the keyboard.

Note: The pianist style will automatically play an introduction. To turn-off the introduction, press the INTRO/ENDING button until the indicator is unlit.

4. Press the INTRO/ENDING button or the START/STOP button (located to the left of the cursor buttons.)

5. Press the EXIT button (located to the right of the cursor buttons.)

Refer to the Owner’s Manual, pg. 28 for more information.

TurboStart

Note: If “Delete the selected song. OK?” appears on the screen, press the cursor [4] button until YES is highlighted on the screen and then press the ENTER button (located to the right of the cursor buttons.)

3. Press the REC [=] button (located to the right of the cursor buttons .)

Note: The REC button indicator will light and the PLAY button will blink.

4. Press the METRONOME button (located to the right of the cursor buttons) and use the SLOW and FAST buttons to adjust the tempo.

5. Play a song.

6. Press the STOP [<] button when you are done.

7. Press the RESET [9] button.

8. Press the PLAY [4] button to play the song.

Refer to the Owner’s Manual, pp. 31 –32 for more information.

Playing a Song from Disk

Use the following procedure to play a song from disk:

1. Insert a compatible SMF music disk into the drive.

2. Press the SONG button (located to the right of the cursor buttons ) several times until DISK is highlighted on the screen.

3. Use the cursor [3][4][5][6] buttons to locate a song on the screen.

Note: If “Deletes the song. OK?” appears on the screen, press the cursor [4] button until YES is highlighted on the screen and then press the ENTER button (located to the right of the cursor buttons.)

4. Press the PLAY [4] button (located to the right of the cursor buttons ) to play the song; press the

STOP [<] button to silence the piano.

Refer to the Owner’s Manual, pg. 40 for more information.

Recording a Song

Use the following procedure to record a song:

1. Press the SONG button (located to the right of the cursor button.)

2. Use the cursor [3][4][5][6] buttons to locate “0: New Song” on the screen.

Saving a Recorded Song to Disk

Use the following procedure to save a recorded song to disk:

1. Record a song as described under “Recording a Song.”

2. Insert a formatted disk into the drive.

Note: Make sure the disk was formatted on an HPi-5 (Refer to the Owner’s Manual, pp. 36–37 for more information.)

3. Press the FUNCTION button (located to the left of the cursor buttons .)

4. Use the cursor [4][6] buttons to locate DISK on the screen, then press the ENTER button (located to the right of the cursor buttons.)

5. Press the ENTER button again to save in the Roland i-Format.

6. Specify the song name and the save-destination song number.

Note: Use the cursor [3][4] buttons to select an item to set; use the cursor [5][6] buttons to change characters or song numbers.

7. Press the ENTER button.

8. Press the EXIT button twice to return to the main screen.

Refer to the Owner’s Manual, pp. 36 –38 for more information.