LD-701 Series
LED displays
Large flat displays
LD-701 Series
The LD-701 series were designed in
response to the need for large, flat displays.
These are three-chip, flat displays with high
luminance.
!!!!
Features
1) Three independent chip elements.
2) Large 4.5 x 19.8 mm emission area.
3) Thin outer casing, multiple units can be
coupled together.
4) Four colors are available: red, orange,
yellow and green.
!!!!
External dimensions
(Units : mm)
4.5
±
0.1
19.8±0.1
5.6±0.1
5.0±0.5
(2.5)
0.6
0.3
(1.525)
2°
R4
21.0
5.7
(7.0)(7.0)
Pin No.1 2 3 4 5 6
Pin No.1 2 3 4 5 6
Tolerances are
±0.3
unless otherwise noted:
!!!!
Selection guide
Red
LD-701VR
Orange
LD-701DU
∗
Yellow
LD-701YY
∗
Green
LD-701MG
Emitting color
Type
∗Order-based production.
!!!!
Absolute maximum ratings
(Ta = 25°C)
Parameter
Symbol
Red
Unit
LD-701VR Orange LD-701DU
Yellow LD-701YY Green LD-701MG
mW
mA
mA
V
°C
°C
P
D
I
F
I
FP
V
R
Topr
Tstg
Power dissipation
Forward current
Peak forward
current
Reverse voltage
Operating
temperature
Storage
temperature
180
20
60
∗
60
∗
60
∗
60
∗
3
180
20
3
180
20
3
225
25
3
−25~+75
−30~+85
∗
Pulse width 1ms duty 1 / 5
LD-701 Series
LED displays
!!!!
Electrical and optical characteristics
(Ta = 25°C)
Parameter Symbol
Red Orange Yellow Green
UnitConditions
Min. Typ. Max. Min. Typ. Max.
3.0 V
µA
nm
nm
2.03.02.0
650
40
10
610
40
10
−
−−
−
−
−
−
−
−−
−
−
−−
Min. Typ. Max.
3.02.1
585
40
10
−
−−
−
−
−−
Min. Typ. Max.
3.02.1
563
40
10
−
−−
−
−
−−
I
F
= 10mA
V
R
= 3V
I
F
= 10mA
I
F
= 10mA
V
F
I
R
λ
P
∆λ
Forward voltage
Reverse current
Peak wavelength
Spectral line half
width
Electrical and optical values are guaranteed values per element.
!!!!
Luminous intensity vs. wavelength
1.0
0.8
0.6
0.4
0.2
0
500 550 600 650 700 750
Axial Luminous Intensity
Wavelength : λ
P
(
nm)
Green Yellow
Orange
Red
!!!!
Luminous intensity
Color
Orange
Yellow
Green
Type
LD-701VR
LD-701DU
LD-701YY
LD-701MG
Red
Min.
3.6
3.6
2.2
3.6
Typ.
10
10
6.3
10
Max.
−
−
−
−
Unit
mcd
mcd
mcd
mcd
Note 1: Measured at IF = 10mA
Note 2: Current passes through all elements.
!!!!
Operation notes
When forming leads, the bend should be at least 2mm from the base of the package. Solder after forming the leads, and
ensure that the inside of the LED is not subjected to mechanical stress while it is hot.