Rocky Mountain Radar KAT-MATRIX User Manual

Thank you for purchasing the MATRIX developed by KAT Inc.
MATRIX is specially designed to be a simple-to-use addition to
any vehicle with battery operation and a highly sophisticated
processing system.

We are pleased to have you as a valued customer and hope
you will be delighted with your MATRIX.

This manual provides all the information you need for putting
the MATRIX to work for you.

WARNING: Always obey all local and federal laws when using
this device. This device is not intended for use on the street or
highway. Use only in designated areas with care and do not
take your eyes off the road. MATRIX records the results after
the run. We are not responsible for any accident or injures that
occur while using this device. Drive safely.

MATRIX is designed as a test device to measure performance
of the vehicle. Please use it for that purpose only.

DISPLAY WITH EVERYTHING ILLUMINATED

POWER ON/OFF

Press the MODE button to turn the Matrix ON. It displays each
mode and G-Force mode when ready to start.

Press MODE button for two (2) seconds to turn the Matrix OFF.

SET-UP

If this is the first time the unit is powered since installation or if
the orientation has changed, please move the vehicle to a level
place and press START button to calibrate the three-axis
accelerometer.

To accurately measure horsepower, the correct vehicle weight
and the correction factor for the vehicle must also be entered to
allow a horsepower calculation. To enter set-up mode, press
MEMORY button for three (3) seconds until SETUP shows in
the display.

Vehicle Weight

You must enter the weight of your vehicle. This information is
available in your vehicle’s manual. You should add the weight
of the driver, passengers and cargo plus any additional
equipment added to the vehicle.

Press the UP or DOWN button until the correct weight is
shown. Holding either button for 1 second causes the weight to
change rapidly. Press STORE to store the setting.

Horsepower Factor

This is a correction factor you can set for an approximate
conversion from wheel horsepower to engine horsepower.
Factory default is 1.00.

The Matrix is affected by drive train losses, rolling resistance
and aerodynamic drag which determine the vehicle’s
performance. Manufacturers’ ratings list a higher engine
horsepower which is not reduced by these other real-world
factor so you may need to increase the wheel horsepower
readings to approximately correlate to higher engine
horsepower.

Display flashes previously set value. Press the up and down
buttons until the vehicle correction shows in the display. Press
STORE to store the setting.

Horsepower Speed Range

You must select the speed range for horsepower calculations.
The Matrix will calculate the average horsepower over this
range and the peak horsepower within this range.

The setup item HP MIN SPEED sets the speed that the Matrix
starts measuring horsepower.

The setup item HP MAX SPEED sets the speed that the Matrix
stops measuring horsepower.

Display flashes previously set value. Set the minimum speed
for the average horsepower measurement by pressing the UP
or DOWN buttons. Press STORE button to store the result.
Set the maximum speed for the average horsepower
measurement by pressing the UP or DOWN buttons. Press
STORE button to store the result

The maximum of the HP MIN Speed cannot exceed the
minimum of the HP MAX speed.

SET-UP ITEMS

MIN MAX DEFAULT STEP
WEIGHT 25 16000 2000 25
HP FACTOR 1.00 2.00 1.00 0.01
HP MIN SPEED 10 60 30 1

HP MAX SPEED 30 100 50 1

Unit enters G-Force mode after setup and the display shows
the current G-Force reading. G-Force can be zeroed at any
time by pressing START button.

Mount MATRIX on the windshield centered between driver and
passenger. MATRIX must be positioned straight across the
vehicle. Do not angle the device toward the driver. The front
of the device does not have to be perfectly level. This device
automatically compensates for mounting angles up to 30
degrees from level.

Adjust the device on its windshield bracket until it is
approximately level. It is important that the device stays in
position during use. If the device moves too easily, tighten the
screw in the bracket or attach suction cups firmly.

MATRIX

INTRODUCTION

OPERATION

1

MATRIX

2

MATRIX

3

MATRIX

4

MATRIX

5

MATRIX

6

MATRIX

7

MATRIX

8

MATRIX

WHAT’S IN THE PACKAGE

Operation Operation Operation

INSTALLATION HOW DOES IT WORK?

MATRIX DEVICE

WINDSHIELD BRACKET

3 AAA BATTERIES 3 SUCTION CUPS

INSERT THE BATTERIES WHAT CAN IT MEASURE?

The device is operated from three AAA batteries with a
capacity of approximately 1,000mA hours. Battery life is
approximately 40 hours with backlight.

Open the battery door on the back of the MATRIX and
insert three AAA batteries.

MATRIX can measure the followings:

1. Time to go from 0 to 60MPH

2. Speed at the end of 1/4 mile

3. G-Force

4. Peak and Average Horsepower

The MATRIX measures the performance of your vehicle by
sensing acceleration forces. It uses a three-axis accelerometer
to measure acceleration. This digital three-axis accelerometer
sensor tracks your vehicle’s acceleration and concerning
forces. This device analyzes data and calculates corrected G­Forces for the G Meter operation, speed and distance data.

The result is the most accurate and it is the first device with
battery operation.

SERVICE

If you wish to return the Matrix, please contact KAT Inc.

Phone: [phone] Fax: [phone]

Owner’s Manual

9

MATRIX

10

MATRIX

11

MATRIX

12

MATRIX

13

MATRIX

14

MATRIX

15

MATRIX

16

MATRIX

17

MATRIX

LIMITED WARRANTY

18

MATRIX

OPERATION

Six push buttons control operation. The MODE button cycles
through the operational modes, 1⁄4 MILE, 0 TO 60, and G­Force. The MEMORY button selects memory locations
containing results of tests. STORE button causes the current
test results to overwrite the location of a selected memory
location. The UP and DOWN buttons scroll data from memory
or test results and change setup data. The START button zeros
the three-axis accelerometer readings.

Your car must be stopped before you perform a test.

0 to 60

Pressing the MODE key until the display shows:

The test begins as soon as the vehicle starts moving and the
display shows the elapsed time until 60 MPH is reached.
Then it shows the time to reach 60 MPH

MODE BUTTON

- Press MODE button to power the unit on. Press two (2)
seconds to power the unit off.

- You can choose the mode you want by pressing this MODE
button when that mode is displayed: 1/4Mile, 0-60Mile, G­Force.

START BUTTON

Press START button at each mode to perform testing. Start
when the display is ready.

MEMORY BUTTON

Press the MEMORY button any time a test is not running until
the desired memory location is shown in the display. Press the
UP and DOWN keys to scroll through the test results. Press
START or MODE buttons to exit the MEMORY mode.

Press MEMORY button for three (3) seconds to enter set-up
mode.

STORE BUTTON

At the end of any test, press the MEMORY button until the
desired memory location, MEM 1, MEM 2 or MEM 3 shows in
the display. Then press STORE button to overwrite the display
with the new information. The results of the test are stored in
memory.

UP AND DOWN BUTTONS

Press UP or DOWN buttons to review data from last tests.
Press DOWN button for five (5) seconds to enter Factory Reset

Mode.

FACTORY RESET

Press DOWN button for five (5) seconds to enter Factory Reset
mode and press STORE button to reset all data to factory
default.

- Clear all memories

- Set-up items

- Calibration data
Press MEMORY button to cancel the factory reset.

CALIBRATION

Calibration is performed automatically when you press START
button

MEMORY

Setup and test results are stored in memory so data is retained
when power is OFF or batteries changed.

DISPLAY BACKLIGHT

The backlight is turned on when any button is pushed and
remains on for 1 minute unless a test is being run, then it stays
on until 1 minute after the test is completed. Each button push
resets the 1 minute timer.

AUTO POWER OFF

The Matrix will automatically shut off the power after one hour if
no buttons are pressed.

The Matrix will give warning beep before power off. Press any
buttons to cancel auto power off.

Low Battery Warning

The Matrix will give low battery warning from the moment when
there is about two hours of remaining battery life.

ERROR MESSAGES

ERROR 1: Speed decrease during testing
ERROR 2: Tilted more than 30 degrees during calibration
ERROR 3: Vibration during calibration

The manufacturer warrants your Matrix against all defects in
materials and workmanship for a period of one (1) year from
the date of the original purchase, subject to the following terms
and conditions: The sole responsibility of the manufacturer
under this Warranty is limited to either repair or, at the option of
the manufacturer, replacement of the Matrix. There are no
expressed or implied warranties, including those of fitness for a
particular purpose of merchantability, which extend beyond the
face hereof. Some states do not allow limitations on how long
an implied warranty lasts, so the above limitations may not
apply to you.

Pressing the UP or DOWN button once causes the display to
show average horsepower between the two speeds chosen in
setup.

Pressing the UP or DOWN button again shows the peak
horsepower reached during the test.

1⁄4 MILE

Press the MODE button until the display shows:

The test begins as soon as the vehicle starts moving and the
display shows current elapsed time. At the end of 1⁄4 mile, the
speed reached is displayed.

Pressing the UP or DOWN button causes the display to show
the time for 1⁄4 mile.

Pressing the UP or DOWN button causes the display to show
average horsepower between the two speeds chosen in setup.

Pressing the UP or DOWN button shows the peak horsepower
reached during the test.

G-FORCE

Pressing the MODE button until the display shows G Force.
The display shows the number of horizontal and forward Gs.

The right indicator is sideways acceleration with the arrow
indicating direction. The left is forward acceleration. The arrow
points up when speed is increasing and down when speed is
decreasing.

Operation OperationOperationOperation

OperationOperation Operation Operation

Operation