Rockwell Automation AK-U0-RJ45-SC1 User Manual
RJ45 Splitter Cable (Catalog No. AK-UO-RJ45-SC1)
Panel Mount Unit
aste
p
e
g
|
SI
E
g
|
E
9
6
3
0
SI
Panel Mount Unit
g
|
SI
Installation Instructions
for use with DSI/ MDI Drive Products
Connecting One Temporary Peripheral Connecting Two Permanent Peripherals
DSI / MDI Drive
SelEsc
Serial Converter
M
S
DSI / MDI
Hand Held
or
LANGDISP
REMOVE
EscEsc
SelSel
ALT
8
9
7
Jog
4
5
6
1
2
3
0
+/-
.
DSI
Parameter 1 [Adapter Cfg] set to "Auto"
(default) or "Master" and connected to
Master port (M) on RJ45 Splitter Cable
Parameter 9 [Device Type] set to "Auto"
(default) or "Master" and connected to
Master port (M) on RJ45 Splitter Cable
Connecting One Temporary Peripheral
and One Permanent Peripheral
NEMA 4
DSI /MDI Drive
REMOV
SelEsc
M
S
Parameter 9 [Device Type]
set to "Slave" and
connected to Slave port (S)
on RJ45 Splitter Cable
D
Parameter 9 [Device Type] set to
"M
DSI
or
Jo
r" and connected to Master
ort (M) on RJ45 Splitter Cabl
REMOV
or
Jo
Connecting an RS-485 Network
NEMA 1 Bezel
with DSI / MDI
Hand Held
REMOVE
REMOVE
+/-
D
ALT
Jog
ALT
Jog
DSI / MDI Drive
SelEsc
Parameter 1 [Adapter Cfg]
set to "Auto" (default) or
"Slave" and connected to
Slave port (S) on
RJ45 Splitter Cable
NEMA 4
M
S
Serial Converter
REMOVE
or
Jo
D
Parameter 9 [Device Type]
set to "Master" and
connected to Master port
(M) on RJ45 Splitter Cable
NEMA 1 Bezel
with DSI / MDI
Hand Held
REMOVE
ALT
Jog
AK-U0-RJ45-TR1
Terminating Resistor
(end of network)
Both the Master (M) and Slave (S) ports on the RJ45 Splitter
Cable operate as standard RS-485 ports in this configuration.
DSI / MDI Drives
SelEsc
AK-U0-RJ45-TB2P
Two-position
Terminal Block
or
Customer supplied RJ45 male-to-RJ45 male
cables with wires connected at pins 4 and 5 only.
Important: For connectivity guidelines relating to all configurations, see next page.
SelEsc
or
Connectivity Guidelines
!
•Two peripherals maximum can be attached to a drive.
• If a single peripheral is used, it must be connected to the Master port (M) on the splitter
and configured for “Auto” (default) or “Master.” Parameter 9 [Device Type] on the DSI /
MDI keypads and Parameter 1 [Adapter Cfg] on the Serial Converter are used to select the
type (Auto / Master / Slave).
• Do not use the RJ45 Splitter Cable with a drive that has an internal network
communication adapter installed. Since only one additional peripheral can be added, the
second peripheral can be connected directly to the RJ45 port on the drive. The internal
Comm is always the Master, therefore the external peripheral must be configured as
“Auto” (for temporary connections) or “Slave” (for permanent connections).
• If two peripherals will be powered up at the same time, one must be configured as the
“Master” and connected to the Master port (M) and the other must be connected as the
“Slave” and connected to the Slave port (S).
ATTENTION: Risk of injury or equipment damage exists. The peripherals may
not perform as intended if these Connectivity Guidelines are not followed.
Precautions should be taken to follow these Connectivity Guidelines.
Refer to the drive user manual for specific DSI / MDI accessory part numbers.
Publication RA-IN00 3A-EN-P – October, 2002 P/N 316515-P01
Copyright © 2002 Rockwell Automation, Inc. All rights reserved. Printed in USA.
Loading...