Rockwell Automation 140G-K-TLA User Manual [fr, en, de]

140G-K-TLA_, 140G-K-TLC_, 140G-K-MTL_
Cu/CuAl terminal lug installation for 140G-K Cu/CuAl Terminali anteriori per cavi in rame/rame - alluminio Cu/CuAl Vorderseitige Anschlüsse für Kabel aus Kupfer/Kupfer - Aluminium Cu/CuAl Prises avant pour câbles en cuivre/cuivre - aluminium Cu/CuAl Terminales frontales para cables de cobre/cobre - aluminio
Bul. 140G/140MG
Installation - Installazione - Instalación Instalação - -
WARNING:
installing or servicing. Install in suitable enclosure. Keep free from contaminants. (Follow NFPA70E requirements).
AVVERTENZA: Per prevenire infortuni, togliere tensione prima dell'installazione o manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti. (Seguire i requisiti NFPA70E).
Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden. (Befolgen Sie die Anforderungen nach NFPA70E).
AVERTISSEMENT:
secteur pour éviter toute décharge. Prévoir une mise en coffret ou armoire appropriée. Protéger le produit contre les environnements agressifs. (Vous devez respecter la norme NFPA70E).
ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la instalación o del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada. Manténgalo libre de contaminantes. (Cumpla con los requisitos NFPA70E).
ATENÇÃO: Para evitar choques, desconectar da corrente elétrica antes de fazer a instalação ou a manutenção. Instalar em caixa apropriada. Manter livre de contaminantes. (Cumpra as exigências da norma NFPA70E).
To prevent electrical shock, disconnect from power source before
Vor Installations- oder Servicearbeiten Stromversorgung zur
Avant le montage et la mise en service, couper l'alimentation
Cu/CuAl Cu/CuAl Cu
CH 8 mm CH 5 mm
CH 8 mm
CH 7 mmCH 7 mm CH 7 mm
3p
1 1
3 4
3 4
3
3
4p
4
4
43
1
159 lb in
18 Nm
CH 7 mm
CH 8 mm
MIN MAX
min 56.5
0.61" dia max Ø max 15.5
2
95 mm
2
120 mm
2/0 AWGMIN
250 mcmMAX
min 2.22”
min 22.6
min 0.89”
274 lb in
31 Nm
DIR 1000436R0826 (L7295)
2
0.85” dia max Ø max 21.5
159 lb in
18 Nm
6
min 0.93”
min 23.5
CH 8 mm
7
380 lb in
43 Nm
12.8
0.505"
10.8
0.425"
OK!
10.8
0.425"
OK!
3.5 mm
0.14”
12.8
0.505"
NO!!
8
2
120 mmMIN
2
240 mm
MAX
250 mcmMIN 500 mcmMAX
3
159.31 lb-in 18 Nm
CH 5 mm
MIN MAX
35min
1.37"
min
0.38" dia max
9.8Ømax
15min
min 0.59"
0.38" dia max
9.8Ømax
61.95 lb-in 7 Nm
2
mm
16
2
mm
50
6AWGMIN
1/0AWGMAX
Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc. Trademarks not belonging to Rockwell Automation are property of their respective companies.
Publication 140G-IN020A-MU-P - April 2013
DIR 1000436R0826 (L7295)
Copyright © 2013 Rockwell Automation, Inc. All Rights Reserved.
Loading...