Page 1
Bul. 140G/140MG
140G-K-RMX, 140G-K-NVM_, 140G-K-RVM_, 140G-N7, 140G-N8
Rotary operating mechanism with: external handle or external handle with internal NFPA 79 operating handle
Installation - Installazione - Instalación
Instalação - -
WARNING: To prevent electrical shock, disconnect from power source before
installing or servicing. Install in suitable enclosure. Keep free from contaminants.
(Follow NFPA70E requirements).
AVVERTENZA: Per prevenire infortuni, togliere tensione prima dell'installazione o
manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti.
WARNUNG: Vor Installations- oder Servicearbeiten Stromversorgung zur
Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem
passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden.
AVERTISSEMENT: Avant le montage et la mise en service, couper l'alimentation
secteur pour éviter toute décharge. Prévoir une mise en coffret ou armoire
appropriée. Protéger le produit contre les environnements agressifs.
ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la instalación o
del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada.
Manténgalo libre de contaminantes.
ATENÇÃO: Para evitar choques, desconectar da corrente elétrica antes de fazer a
instalação ou a manutenção. Instalar em caixa apropriada. Manter livre de
contaminantes.
Cat No.
140G-K-RMX
(4) M4 - 50 mm
(2) 4 - 16 mm
Hi-Low
Self Tapping
Cat No.
140U-HM4
140U-HM4E
Cat No.
140G-K-RMX
Cat No.
140U-HM4
140U-HM4E
CLACK
(4) M4 - 50 mm
(2) 4 - 16 mm
Hi-Low
Self Tapping
Cat No.
194R-R7
194R-R8
PN-258432
DIR 1000436R0612 (Version 02)
Cat No.
140G-N7
140G-N8
Cat No.
140G-K-OSB
(2) M4 - 60 mm
Page 2
1
C
C
Cat
194R-S1
194R-S2
305
(12)
533
(21)
1
MIN MAX
229
(9)
229
(9)
C
(17 - 3/4)
(26 - 3/4)
450.8
679.4
Cat
140G-N7
140G-N8
305
(12)
533
(21)
1
C
MIN MAX
280
(11)
280
(11)
450.8
(17 - 3/4)
679.4
(26 - 3/4)
mm
(in.)
152.5 6.3
(6) (1/4)
C- +
2
16
(5/8)
Ø 3
(Ø 1/8)
3
3
(1/8)
mm
(in.)
152.5 6.3
(6) (1/4)
C- +
2
(Ø 1/8)
16
(5/8)
Ø 3
3
(1/8)
3
PN-258432
DIR 1000436R0612 (Version 02)
(2)
Page 3
2
1
3
3
1
2
9.7 lb-in
(1.1 Nm)
9.7 lb-in
(1.1 Nm)
2
3
12.4 lb-in
(1.4 Nm)
PN-258432
DIR 1000436R0612 (Version 02)
or
or
12.4 lb-in
(1.4 Nm)
(3)
Page 4
4
*Minimum distance from hinge to shaft centerline is 76 mm / 3 inches *Minimum distance from hinge to shaft centerline is 76 mm / 3 inches
Masking tape
Du ruban adhésif
Abdeckband
Cinta adhesiva
Fita adesiva
Nastro adesivo
Masking tape
Du ruban adhésif
Abdeckband
Cinta adhesiva
Fita adesiva
1
Nastro adesivo
1
2 2
Mark from shaft head
Marque de la tête de l'arbre
Markieren Sie vom Schachtkopf
Marca desde la cabeza del eje
Marca da cabeça do eixo
Segna dalla testa dell'albero
PN-258432
DIR 1000436R0612 (Version 02)
Mark from shaft head
Marque de la tête de l'arbre
Markieren Sie vom Schachtkopf
Marca desde la cabeza del eje
Marca da cabeça do eixo
Segna dalla testa dell'albero
3 3
(4)
Page 5
5
BULLETIN 190/194R/140U
DRILLING TEMPLATE
GABARIT DE PERFORATION
PLANTILLA DE PERFORACIÓN
MODELO DE PERFORAÇÃO
STAMPO PREFORATO
ø 65 mm
2-9/16 " DIA.
-HM4E
-HM4
-HM1-N3
194R 140U
TAPE
1
BULLETIN 190 /194R/140U
DRILLING TEMPLATE
BOHRSCHABLONE
GABARIT DE PERFORATION
PLANTILLA DE PERFORACIÓN
MODELO DE PERFORAÇÃO
STAMPO PREFORATO
ø 65 mm
2-9/16 " DIA.
40053-308-01 (4)
Printed in U.S.A.
75
mm
(in.)
ø 65
(ø 2 - 9/16)
37.5
(1 - 15/32)
(2 - 61/64)
-HM1E-N3
-HM1-N2
-HM4-N3
-HM1E-N2
-HM4E-N3
-HM1-N1
-HM4-N2
190/194R
-HM1E-N1
-HM4E-N2
-HM1
-HM4-N1
-HM1E
-HM4E-N1
-HM4
4 - ø 5.5 mm
-HM4E
4 - 7/32 " DIA.
37.5
(1 - 15/32)
2
40053-308-01 (4)
Printed in U.S.A.
BOHRSCHABLONE
1.2 - 4.8
(3/64 - 3/16)
190/194R 194R 140U
-HM1
-HM1-N1
-HM1-N2
-HM1-N3
-HM1E-N2
-HM4-N2
-HM4E-N2
-HM1E-N3
-HM4-N3
-HM4E-N3
-HM4E
-HM4
-HM1E
-HM4
-HM4E
-HM1E-N1
-HM4-N1
-HM4E-N1
4 - 7/32 " DIA.
4 - ø 5.5 mm
Partie frontale du panneau
Front of Cover
Vorderseite des deckels
Frente de la tapa
Frente da tampa
Parte frontale del panello
(4) - ø 5.5
( (4) - ø 7/32)
3 3
75
(2 - 61/64)
4 4
PN-258432
DIR 1000436R0612 (Version 02)
2.8 Nm
(25 lb-in)
2.8 Nm
(25 lb-in)
(5)
Page 6
6 mm
(.24 in)
Max
Rockwell Automation maintains current product environmental information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page.
Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
PN-258432
Publication 140G-IN002B-MU-P - April 2018
Copyrig ht © 2018 Rockwell A utomation, Inc. All Rights Reserved. P rinted in USA.
DIR 1000436R0612 (Version 02) - (L8716)
Loading...