Robustel R2000 Ent Installation And Configuration Quick Manual
-1-
Installation and Configuration Quick Guide
R2000 Ent
Industrial Dual Module Cellular VPN Router with Voice
5 Eth + 1 Voice/RS-232/RS-485 + 1 USB Host
Environmental Requirements
Input voltage: 9 to 36V DC
Power consumption: 350 mA@12 V in idle state, 500 mA (peak) @12 V in communication state
Operating temperature: -25 to +70 °C
Relative humidity: 5 to 95% RH
Package Contents
Optional Accessories (sold separately)
3G/4G SMA cellular antenna
(stubby/magnet optional)
RP-SMA WiFi antenna
(stubby/magnet optional)
Wall mounting kit
35 mm DIN rail mounting kit
L-type screwdriver
Before installing your R2000 Ent Router, verify the kit contents as following.
1 x Robustel R2000 Ent Industrial Dual Module Cellular VPN Router
with Voice
1 x Quick Start Guide with download link of other documents or tools
Note: If any of the above items is missing or damaged, please contact your
Robustel sales representative.
Ethernet cable
RJ11 to RJ11 phone
connectivity cable
AC/DC power adapter
(12V DC, 1.0 A; EU/US/
UK/AU plug optional)
-2-
Hardware Introduction
1.
Overview
2. Dimensions
3. RJ11 Interface
PIN
Voice
Direction
1
NC
-- 2 NC
-- 3 RINGD/RDC
I/O 4 TIPD/TDC
I/O 5 NC
-- 6 NC
--
-3-
PIN
RS-232
Direction
1
NC
-- 2 GND
-- 3 RXD
Router Device
4
TXD
Router Device
5
GND
--
6
NC
-- PIN
RS-485
Direction
1
NC
--
2
GND
--
3 B RS485_D-
4 A RS485_D+
5
GND
-- 6 NC
--
4. LED Indicators
Name
Color
Status
Description
RUN
Green
On, fast blinking
(250 mSec blink time)
Router is powered on
(System is initializing)
On, blinking
(500 mSec blink time)
Router starts operating
Off
Router is powered off
NET1
(Represents for
the Module1)
Green
On, solid
Network is joined successfully by
using the Module1 card and worked
in an optimum one
On, blinking
Network is joined successfully but
worked in a lower-level than
standard
Off
Network is not joined or joining
Name
Color
Status
Description
NET2
(Represents for
the Module2)
Green
On, solid
Network is joined successfully by
using the Module2 card and worked
in an optimum one
On, blinking
Network is joined successfully but
worked in a lower-level than
standard
Off
Network is not joined or joining
RSSI1
(Represents for
the signal value
of Module1)
Green
On, solid
High signal strength (21-31) is
available
On, slow blinking
(1 sec blink time)
Medium signal strength (11-20) is
available
On, fast blinking
Low signal strength (1-10) is
available
Off
No signal
RSSI2
(Represents for
the signal value
of Module2)
Green
On, solid
High signal strength (21-31) is
available
On, slow blinking
Medium signal strength (11-20) is
available
On, fast blinking
Low signal strength (1-10) is
available
Off
No signal
USR-SIM
Green
On, blinking
Backup card is being used
Off
Main card is being used
USROpenVPN
Green
On, solid
OpenVPN connection is established
Off
OpenVPN connection is not
established
USR-IPsec
Green
On, solid
IPsec connection is established
Off
IPsec connection is not established
USR-WiFi
Green
On, solid
WiFi is enabled and working
properly
Off
WiFi is disabled or not working
properly
WAN/ETH1/
ETH2/ETH3/
ETH4
Green
On, solid
Connection is established
On, blinking
Data is being transferred
Off
Connection is not established
-4-
5. USB Interface
Function
Operation
Firmware
upgrade
USB interface is used for batch firmware upgrading, but cannot
be used for sending or receiving data from slave devices which
connected to it. You can insert a USB storage device into the
router’s USB interface, such as a U disk or a hard disk. If there
have a supported configuration file or a router firmware in this
USB storage device, the router will automatically update the
configuration file or the firmware.
6. Reset Button
Function
Operation
Reboot
Press and hold the RST button for 2 to 7 seconds under the
operating status.
Restore to
factory default
settings
Wait for 5 seconds after powering up the router, press and hold
the RST button for about 16 seconds until all six LEDs start
blinking one by one, and release the button to return the
router to factory defaults.
7. Ethernet Port
R2000 Ent Router has five Ethernet ports, including WAN, ETH1, ETH2, ETH3
and ETH4. And every Ethernet port corresponds to a specific LED indicator in
the bottom view of the router. For details about status, see the table below.
Indicator
State
Description
Link Indicator
On, solid
Connection is established
On, blinking
Data is being transferred
Off
Connection is not established
Loading...