A
Module Type Controller SRV
Temperature Control Module [Extension Type]
V-TIO-B/V-TIO-D
Instruction Manual
IMS01P03-E6
Thank you for purchasing this RKC product. In order to
achieve maximum performance and ensure proper operation
of your new instrument, carefully read all the instructions in
this manual. Please place this manual in a convenient
location for easy reference.
SYMBOLS
WARNING
CAUTION
An external protection device must be installed if
failure of this instrument could result in damage to
the instrument, equipment or injury to personnel.
All wiring must be completed before power is turned
on to prevent electric shock, fire or damage to
instrument and equipment.
This instrument must be used in accordance with the
specifications to prevent fire or damage to
instrument and equipment.
This instrument is not intended for use in locations
subject to flammable or explosive gases.
Do not touch high-voltage connections such as
power supply terminals, etc. to avoid electric shock.
RKC is not responsible if this instrument is repaired,
modified or disassembled by other than
factory-approved personnel. Malfunction can occur
and warranty is void under these conditions.
This is a Class A instrument. In a domestic environment,
this instrument may cause radio interference, in which
case the user may be required to take adequate measures.
: This mark indicates precautions that must be
taken if there is danger of electric shock, fire,
etc., which could result in loss of life or injury.
: This mark indicates that if these precautions
and operating procedures are not taken,
damage to the instrument may result.
: This mark indicates that all precautions should
!
be taken for safe usage.
: This mark indicates important information on
installation, handling and operating
procedures.
: This mark indicates supplemental information
on installation, handling and operating
procedures.
: This mark indicates where additional
information may be located.
WARNING
!
CAUTION
This instrument is protected from electric shock by
reinforced insulation. Provide reinforced insulation between
the wire for the input signal and the wires for instrument
power supply, source of power and loads.
Be sure to provide an appropriate surge control circuit
respectively for the following:
− If input/output or signal lines within the building are
longer than 30 meters.
− If input/output or signal lines leave the building,
regardless the length.
This instrument is designed for installation in an enclosed
instrumentation panel. All high-voltage connections such
as power supply terminals must be enclosed in the
instrumentation panel to avoid electric shock by operating
personnel.
All precautions described in this manual should be taken to
avoid damage to the instrument or equipment.
All wiring must be in accordance with local codes and
regulations.
All wiring must be completed before power is turned on to
prevent electric shock, instrument failure, or incorrect
action.
The power must be turned off before repairing work for
input break and output failure including replacement of
sensor, contactor or SSR, and all wiring must be
completed before power is turned on again.
To prevent instrument damage or failure, protect the power
line and the input/output lines from high currents with a
protection device such as fuse, circuit breaker, etc.
Prevent metal fragments or lead wire scraps from falling
inside instrument case to avoid electric shock, fire or
malfunction.
Tighten each terminal screw to the specified torque found
in the manual to avoid electric shock, fire or malfunction.
For proper operation of this instrument, provide adequate
ventilation for heat dispensation.
Do not connect wires to unused terminals as this will
interfere with proper operation of the instrument.
Turn off the power supply before cleaning the instrument.
Do not use a volatile solvent such as paint thinner to clean
the instrument. Deformation or discoloration will occur. Use
a soft, dry cloth to remove stains from the instrument.
To avoid damage to instrument display, do not rub with an
abrasive material or push front panel with a hard object.
Do not connect modular connectors to telephone line.
NOTICE
This manual assumes that the reader has a fundamental
knowledge of the principles of electricity, process control,
computer technology and communications.
The figures, diagrams and numeric values used in this
manual are only for purpose of illustration.
RKC is not responsible for any damage or injury that is
caused as a result of using this instrument, instrument
failure or indirect damage.
RKC is not responsible for any damage and/or injury
resulting from the use of instruments made by imitating this
instrument.
Periodic maintenance is required for safe and proper
operation of this instrument. Some components have a
limited service life, or characteristics that change over time.
Every effort has been made to ensure accuracy of all
information contained herein. RKC makes no warranty
expressed or implied, with respect to the accuracy of the
information. The information in this manual is subject to
change without prior notice.
No portion of this document may be reprinted, modified,
copied, transmitted, digitized, stored, processed or
retrieved through any mechanical, electronic, optical or
other means without prior written approval from RKC.
ll Rights Reserved, Copyright 2002, RKC INSTRUMENT
RKC INSTRUMENT INC.
®
1. OUTLINE
A
Two [basic types] of temperature control (TIO) modules are
available: the V-TIO-B for heat control and the V-TIO-D for
heat/cool control.
As the temperature control (TIO) module [extension type] is not
provide with power supply and host communication terminals,
communication with the host computer is always made with this
module connected to the temperature control (TIO) module
[basic type]. In addition, one digital input (DI) point and two
digital output (DO) points can be optionally added.
All data are set by communication. For details, see the
Module Type Controller SRV Communication Instruction
Manual (IMS01P01-E).
2. PRODUCT CHECK
Before using this product, check each of the following:
• Model code
• Check that all of the accessories delivered are complete.
• Check that there are no scratch or breakage in external
appearance (case, front panel, or terminal, etc).
V–TIO– – – – – /Y
(1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12)
(1) Type
B: Extension type, heat control
D: Extension type, heat/cool control
(2) Control action
[For heat control]
F: PID action with autotuning (AT) (reverse action)
D: PID action with autotuning (AT) (direct action)
[For heat/cool control]
B: Heat/cool PID action with autotuning (AT) (air cooling)
W: Heat/cool PID action with autotuning (AT) (water cooling)
(3) Input range (Each channel common code)
[Thermocouple input]
Type Code Range Code Range
K K02 0 to 400 °C KB9 32 to 752 °F
K04 0 to 800 °C KB8 32 to 1472 °F
K16 −200 to +1372 °C KB7 −328 to +2501 °F
K09 0.0 to 400.0 °C KC2 32.0 to 752.0 °F
K35 −200.0 to +400.0 °CKC1 −328.0 to +752.0 °F
J J02 0 to 400 °C JC2 32 to 752 °F
J04 0 to 800 °C JC1 32 to 1472 °F
J15 −200 to +1200 °CJB9 −328 to +2192 °F
J09 0.0 to 400.0 °C JC4 32.0 to 752.0 °F
J27 −200.0 to +400.0 °CJC3 −328.0 to +752.0 °F
T T08 0 to 400 °C TB9 32 to 752 °F
T09 0 to 200 °C TC1 32 to 392 °F
T16 −200 to +400 °CTB8 −328 to +752 °F
T06 0.0 to 400.0 °C TC3 32.0 to 752.0 °F
T19 −200.0 to +400.0 °CTC2 −328.0 to +752.0 °F
E E01 0 to 800 °C EA8 32 to 1472 °F
E02 0 to 1000 °C EA7 32 to 1832 °F
S S05 0 to 1768 °C SA6 32 to 3214 °F
R R06 0 to 1768 °C RA6 32 to 3214 °F
N N02 0 to 1300 °C NA6 32 to 2372 °F
B B03 0 to 1800 °C BB1 32 to 3272 °F
PLⅡ A02 0 to 1390 °C AA6 32 to 2534 °F
W5Re/
W26Re
[RTD input]
Type Code Range Code Range
Pt100 D17 0 to 400 °C DC5 32 to 752 °F
D33 0 to 850 °C DC4 32 to 1562 °F
D16 0.0 to 400.0 °C DC7 32.0 to 752.0 °F
D28 −200.0 to +400.0 °C DC6 −328.0 to +752.0 °F
JPt100 P17 0 to 400 °C PC5 32 to 752 °F
P23 0 to 600 °C PC4 32 to 1112 °F
P16 0.0 to 400.0 °C PC7 32.0 to 752.0 °F
P28 −200.0 to +400.0 °CPC6 −328.0 to +752.0 °F
W03 0 to 2300 °C WA9 32 to 4172 °F
*
[Voltage/current input]
Code Type Code Type
Voltage 201 0 to 100 mV DC 401 0 to 5 V DC
501 0 to 10 V DC 601 1 to 5 V DC
Current 701 0 to 20 mA DC 801 4 to 20 mA DC
(4) Control output (CH1), (5) Control output (CH2)
M: Relay contact output
V: Voltage pulse output 0/12 V DC
4: 0 to 5 V DC 5: 0 to 10 V DC 6: 1 to 5 V DC
7: 0 to 20 mA DC 8: 4 to 20 mA DC
(6) Event input (DI) [Optional]
N: None
1: Control RUN/STOP
2: Event interlock release
(7) (8) Event output 1 (DO1) [Optional]
(9) (10) Event output 2 (DO2) [Optional]
[(7), (9) code: Channel selection]
N: None 1: Input channel 1 2: Input channel 2
[(8), (10) code: Output type]
N: None A: Deviation high B: Deviation low
C: Deviation high/low D: Band
E: Deviation high with hold action F: Deviation low with hold action
G: Deviation high/low with hold action
H: Process high J: Process low
K: Process high with hold action L: Process low with hold action
Q: Deviation high with re-hold action
R: Deviation low with re-hold action
T: Deviation high/low with re-hold action
P: Heater break alarm 1: Control loop break alarm
2: Burnout 3: Temperature rise completion
(11) CT type (Each channel common code)
P: CTL-6-P-N S: CTL-12-S56-10L-N
(12) Communication function
5: RKC communication (RS-485) 6: Modbus (RS-485)
• For heat/cool PID control (V-TIO-D), input channel
2 becomes unused.
• For heat/cool PID control (V-TIO-D), Control output
1 corresponds to the heating output and Control
output 2 corresponds to the cooling output.
• The heater break alarm function becomes invalid
when the voltage/current output is selected as
control output type.
Accessories
Instruction Manual (IMS01P03-E6)............................ 1
3. PARTS DESCRIPTION
Terminal
cover
FAIL/RUN
RX/TX
EVENT1
EVENT2
EVENT3
EVENT4
3
2
4
1
5
5 5
0
6
9
7
8
3
2
4
1
5
0
6
9
7
8
* Installed when provided with the event input/output (optional).
Indication
lamps
ddress
setting
switches
Event
input/
output
connector
Terminal
cover
FAIL/RUN
When normally:
A green lamp turns on (RUN)
When abnormally:
A red lamp turns on (FAIL)
RX/TX
During data send and receive:
A green lamp turns on
EVENT 1 to 4
Display various states by setting.
Display contents
Event 1 state, Event 2 state,
*
Comprehensive event state,
Output state, Control state
2
IMS01P03-E6
Loading...