Rival S11P User Manual

Electric Skillet

S11P

Owner’s Guide

READ AND SAVE THESE INSTRUCTIONS

S11P07EM1 Rev. A

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions
should always be followed, including the following:

1.Read all instructions before using.

2.Do not touch hot surfaces. Use handles or knobs.

3.To protect against electrical shock, do not immerse cord, plug
or TEMPERATURE CONTROL PROBE in water or other liquid.

4.Close supervision is necessary when any appliance is used near
children. This appliance is not to be used by children.

5.Unplug from outlet when not in use and before cleaning the
appliance. Allow to cool before putting on or taking off parts,
and before cleaning.

6.Do not operate any appliance with a damaged cord or plug or
after the appliance malfunctions or has been damaged in any
manner. Return appliance to the manufacturer (see warranty)
for examination, repair, or adjustment.

7.The use of accessory attachments not recommended by
manufacturer may cause injuries.

8.Do not use outdoors.

9.Do not let cord hang over edge of table or counter, or touch
heated surfaces.

10.Do not place on or near a hot gas or electric burner, or in a
heated oven.

11.Extreme caution must be used when moving appliance containing
hot oil or other hot liquids.

12.Always attach TEMPERATURE CONTROL PROBE to appliance
first, then plug cord in the wall outlet. To disconnect, turn
TEMPERATURE CONTROL DIAL to “OFF”, then remove plug
from wall.

13.Do not use appliance for other than intended use.

-2-

SAVE THESE INSTRUCTIONS

This appliance is for HOUSEHOLD USE ONLY. No user-serviceable
parts inside. Do not attempt to service this product. A short power
supply cord is provided to reduce the hazards resulting from
entanglement or tripping over a long cord. An extension cord may be
used with care. However, the marked electrical rating should be at
least as great as the electrical rating of the skillet. The extension cord
should not be allowed to drape over the counter or tabletop where
it can be pulled on by children or tripped over unintentionally.

POLARIZED PLUG

This appliance has a polarized plug (one blade is

wider than the other). To reduce the risk of

electric shock, this plug will fit into a polarized

outlet only one way. If the plug does not fit fully

into the outlet, reverse the plug. If it still does not
fit, contact a qualified electrician. Do not attempt to modify the
plug in any way. If the plug fits loosely into the AC outlet or if the
AC outlet feels warm do not use that outlet.

Keep Warm Setting

The temperature control probe has a “Keep Warm” range setting of
approximately 150°F to 180°F. The indicator light will cycle on and off
when this setting is in use to indicate that the skillet is maintaining the
desired temperature.

IMPORTANT

Check the HANDLES/LEGS of your skillet periodically for looseness.
If needed, re-tighten with a screwdriver. CAUTION: Overtightening
can result in stripping of screws or cracking of handles and base.

-3-

KNOW YOUR ELECTRIC SKILLET

Figure 1

Spoon Rest
(located on
both sides
of skillet)

Temperature Control dial

Temperature Control probe

HOW TO ASSEMBLE YOUR ELECTRIC SKILLET

Remove all parts from the packaging.

1. Locate Lid Knob in packaging.

2. Holding Lid Knob on the outside top of the Glass Lid, align hole
in Lid Knob into hole located on the outside of the Lid. Knob
should be centered on Glass Lid.

3. Place the Phillips head screw through screw hole on the inside
of the lid.

4. Tighten screw until snug. Do not overtighten. The Lid is now
ready for use.

-4-

HOW TO USE YOUR ELECTRIC SKILLET

1. Set the skillet on a flat, dry, heat resistant surface. Some countertop

®

and table surfaces, such as Corian
designed to withstand the prolonged heat generated by certain
appliances. If you plan to use the product for a prolonged period
of time, we recommend placing a hot pad or trivet under your
skillet beforehand to prevent possible damage to the surface.

2. Turn temperature control to “OFF”, plug temperature control
probe securely into receptacle on skillet, plug into standard 120V
AC outlet and turn temperature control to desired setting.

3. The temperature control indicator light will come on when you
set or adjust the temperature. Once the desired temperature is
reached, the indicator light will go out. (When adding food,
the indicator light will come on briefly as the overall cooking
temperature is reduced.)

4. Preheat the skillet with the lid on for 10 – 15 minutes or until the
indicator light goes out. NOTE: The cooking temperatures listed
in this user manual are estimates. Adjust the cooking temperature
slightly up or down to achieve the results you prefer.

5. A steam vent is located on the Glass Lid. The steam vent allows
steam to escape while cooking with the lid in place. CAUTION:
Escaping steam is hot! Be careful when removing or lifting lid.
Oven mitts are recommended when removing cover from skillet
base or when replacing it.

NOTE: If heating oil, always leave the lid off. If oil smokes,
immediately turn skillet “OFF” and allow to cool.

and other surfaces, are not

-5-