Page 1
OPERATOR’S MANUAL
4-1/2 in. ANGLE GRINDER
DOUBLE INSULATED
R1001
Your angle grinder has been engineered and manufactured to our high standard for dependability, ease of operation, and
operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING:
To reduce the risk of injury, the user must read and understand the operator’s manual before using this product.
Thank you for buying a RIDGID product.
SAVE THIS MANUAL FOR FUTURE REFERENCE
1
Page 2
TABLE OF CONTENTS
Introduction ...................................................................................................................................................................... 2
General Safety Rules .....................................................................................................................................................3-4
Specific Safety Rules ........................................................................................................................................................ 4
Symbols .........................................................................................................................................................................5-6
Electrical ........................................................................................................................................................................... 7
Features .........................................................................................................................................................................8-9
Assembly ...................................................................................................................................................................10-11
Operation ...................................................................................................................................................................11-13
Maintenance ................................................................................................................................................................... 14
Warranty .........................................................................................................................................................................15
Customer Service Information ........................................................................................................................................ 16
INTRODUCTION
This tool has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability have
been given top priority in the design of this product making it easy to maintain and operate.
2
Page 3
GENERAL SAFETY RULES
WARNING:
Read and understand all instructions. Failure to
follow all instructions listed below, may result in
electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
WORK AREA
Keep your work area clean and well lit. Cluttered
benches and dark areas invite accidents.
Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases,
or dust. Power tools create sparks which may ignite the
dust or fumes.
Keep bystanders, children, and visitors away while
operating a power tool. Distractions can cause you to
lose control.
ELECTRICAL SAFETY
Double insulated tools are equipped with a polarized
plug (one blade is wider than the other). This plug will
fit in a polarized outlet only one way. If the plug does
not fit fully in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician to install a
polarized outlet. Do not change the plug in any way.
Double insulation
wire grounded power cord and grounded power supply
system.
Avoid body contact with grounded surfaces such as
pipes, radiators, ranges, and refrigerators. There is an
increased risk of electric shock if your body is grounded.
Don’t expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of electric shock.
Do not abuse the cord. Never use the cord to carry the
tools or pull the plug from an outlet. Keep cord away
from heat, oil, sharp edges, or moving parts. Replace
damaged cords immediately. Damaged cords increase
the risk of electric shock.
When operating a power tool outside, use an outdoor
extension cord marked “W-A” or “W”. These cords
are rated for outdoor use and reduce the risk of electric
shock.
PERSONAL SAFETY
Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use tool
while tired or under the influence of drugs, alcohol,
or medication. A moment of inattention while operating
power tools may result in serious personal injury.
Dress properly. Do not wear loose clothing or jewelry.
Contain long hair. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes, jewelry, or long
hair can be caught in moving parts.
eliminates the need for the three-
Av oid acc i dental startin g . Be s ure swi tch is off
before plugging in. Carrying tools with your finger on the
switch or plugging in tools that have the switch on invites
accidents.
Remove adjusting keys or wrenches before turning
the tool on. A wrench or a key that is left attached to a
rotating part of the tool may result in personal injury.
Do not overreach. Keep proper footing and balance
at all times. Proper footing and balance enables better
control of the tool in unexpected situations.
Use safety equipment. Always wear eye protection.
Dust mask, nonskid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions.
Do not wear loose clothing or jewelry. Contain long
hair. Loose clothes, jewelry, or long hair can be drawn
into air vents.
Do not use on a ladder or unstable support. Stable
footing on a solid surface enables better control of the
tool in unexpected situations.
TOOL USE AND CARE
Use clamps or other practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body is unstable and
may lead to loss of control.
Do not force tool. Use the correct tool for your
application. The correct tool will do the job better and
safer at the rate for which it is designed.
Do not use tool if switch does not turn it on or off.
Any tool that cannot be controlled with the switch is
dangerous and must be repaired.
Disconnect the plug from power source before making
any adjustments, changing accessories, or storing the
tool. Such preventive safety measures reduce the risk of
starting the tool accidentally.
Store idle tools out of the reach of children and other
untrained persons. Tools are dangerous in the hands of
untrained users.
Maintain tools with care. Keep cutting tools sharp
and clean. Properly maintained tools with sharp cutting
edges are less likely to bind and are easier to control.
Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
affect the tool’s operation. If damaged, have the tool
serviced before using. Many accidents are caused by
poorly maintained tools.
Use only accessories that are recommended by the
manufacturer for your model. Accessories that may be
suitable for one tool, may become hazardous when used
on another tool.
Keep the tool and its handle dry, clean and free from
oil and grease. Always use a clean cloth when clean-
ing. Never use brake fluids, gasoline, petroleum-based
products, or any strong solvents to clean your tool. Following this rule will reduce the risk of loss of control and
deterioration of the enclosure plastic.
3
Page 4
GENERAL SAFETY RULES
SERVICE
Tool service must be performed only by qualified re-
pair personnel. Service or maintenance performed by
unqualified personnel may result in a risk of injury.
SPECIFIC SAFETY RULES
Always use proper guard with grinding wheel. A
guard protects operator from broken wheel fragments.
Accessories must be rated for at least the speed
recommended on the tool warning label. Wheels and
other accessories running over rated speed can fly apart
and cause injury.
� Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool may
contact hidden wiring or its own cord. Contact with a
“live” wire will make exposed metal parts of the tool “live”
and shock the operator.
Know your power tool. Read operator’s manual
carefully. Learn its applications and limitations, as
well as the specific potential hazards related to this
tool. Following this rule will reduce the risk of electric
shock, fire, or serious injury.
Always wear safety glasses. Everyday eyeglasses
have only impact-resistant lenses; they are NOT
safety glasses. Following this rule will reduce the
risk of serious personal injury.
Protect your lungs. Wear a face or dust mask if the
operation is dusty. Following this rule will reduce the
risk of serious personal injury.
Protect your hearing. Wear hearing protection
during extended periods of operation. Following this
rule will reduce the risk of serious personal injury.
Inspect tool cords periodically and, if damaged, have
repaired at your nearest Authorized Service Center.
Constantly stay aware of cord location. Following this
rule will reduce the risk of electric shock or fire.
Check damaged parts. Before further use of the
tool, a guard or other part that is damaged should
be carefully checked to determine that it will operate
When servicing a tool, use only identical replacement
parts. Follow instructions in the Maintenance section
of this manual. Use of unauthorized parts or failure to
follow Maintenance Instructions may create a risk of
shock or injury.
properly and perform its intended function. Check
for alignment of moving parts, binding of moving
parts, breakage of parts, mounting, and any other
conditions that may affect its operation. A guard
or other part that is damaged should be properly
repaired or replaced by an authorized service center.
Following this rule will reduce the risk of shock, fire, or
serious injury.
Do not abuse cord. Never carry the tool by the cord
or yank it to disconnect it from the receptacle. Keep
cord away from heat, oil, and sharp edges. Following
this rule will reduce the risk of electric shock or fire.
Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one
heavy enough to carry the current your product
will draw. A wire gage size (A.W.G.) of at least 14
is recommended for an extension cord 50 feet or
less in length. A cord exceeding 100 feet is not
recommended. If in doubt, use the next heavier
gage. The smaller the gage number, the heavier
the cord. An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating.
Inspect for and remove all nails from lumber before
using this tool. Following this rule will reduce the risk of
serious personal injury.
Save these instructions. Refer to them frequently and
use them to instruct others who may use this tool. If you
loan someone this tool, loan them these instructions
also.
WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals
known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure
to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust
masks that are specially designed to filter out microscopic particles.
4
Page 5
SYMBOLS
Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer.
SYMBOL NAME DESIGNATION/EXPLANATION
V Volts
A Amperes
Hz Hertz
W Watt
min Minutes
Alternating Current
Direct Current
n
o
.../min
No Load Speed
Class II Construction
Per Minute
Wet Conditions Alert
Voltage
Current
Frequency (cycles per second)
Power
Time
Type of current
Type or a characteristic of current
Rotational speed, at no load
Double-insulated construction
Revolutions, strokes, surface speed, orbits etc., per minute
Do not expose to rain or use in damp locations.
Read The Operator’s Manual
Eye Protection
Safety Alert
No Hands Symbol
No Hands Symbol
No Hands Symbol
No Hands Symbol
Hot Surface
To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Always wear safety goggles or safety glasses with side shields
and, as necessary, a full face shield when operating this
product.
Precautions that involve your safety.
Failure to keep your hands away from the blade will result in
serious personal injury.
Failure to keep your hands away from the blade will result in
serious personal injury.
Failure to keep your hands away from the blade will result in
serious personal injury.
Failure to keep your hands away from the blade will result in
serious personal injury.
To reduce the risk of injury or damage, avoid contact with any
hot surface.
5
Page 6
SYMBOLS
The following signal words and meanings are intended to explain the levels of risk associated with this
product.
SYMBOL SIGNAL MEANING
DANGER:
WARNING:
CAUTION:
CAUTION:
Indicates an imminently hazardous situation, which, if not avoided, will
result in death or serious injury.
Indicates a potentially hazardous situation, which, if not avoided, could
result in death or serious injury.
Indicates a potentially hazardous situation, which, if not avoided, may
result in minor or moderate injury.
(Without Safety Alert Symbol) Indicates a situation that may result in
property damage.
SERVICE
Servicing requires extreme care and knowledge and should
be performed only by a qualified service technician. For
service we suggest you return the product to your nearest
AUTHORIZED SERVICE CENTER for repair. When servicing, use only identical replacement parts.
WARNING:
To avoid serious personal injury, do not attempt
to use this product until you read thoroughly and
understand completely the operator’s manual.
If you do not understand the warnings and
instructions in the operator’s manual, do not use
this product. Call RIDGID customer service for
assistance.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which can result
in severe eye damage. Before beginning power tool operation, always wear safety goggles or safety glasses
with side shields and, when needed, a full face shield. We recommend Wide Vision Safety Mask for use
over eyeglasses or standard safety glasses with side shields. Always use eye protection which is marked
to comply with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
6
Page 7
ELECTRICAL
DOUBLE INSULATION
Double insulation is a concept in safety in electric power
tools, which eliminates the need for the usual three-wire
grounded power cord. All exposed metal parts are isolated
from the internal metal motor components with protecting insulation. Double insulated tools do not need to be
grounded.
WARNING:
The double insulated system is intended to protect
the user from shock resulting from a break in the
tool’s internal wiring. Observe all normal safety
precautions to avoid electrical shock.
NOTE: Servicing of a tool with double insulation requires
extreme care and knowledge of the system and should be
performed only by a qualified service technician. For service,
we suggest you return the tool to your nearest authorized
service center for repair. Always use original factory replacement parts when servicing.
ELECTRICAL CONNECTION
This tool has a precision-built electric motor. It should be
connected to a power supply that is 120 volts, 60 Hz, AC
only (normal household current). Do not operate this tool
on direct current (DC). A substantial voltage drop will cause
a loss of power and the motor will overheat. If the tool does
not operate when plugged into an outlet, double-check the
power supply.
EXTENSION CORDS
When using a power tool at a considerable distance from
a power source, be sure to use an extension cord that has
the capacity to handle the current the tool will draw. An
undersized cord will cause a drop in line voltage, resulting in
overheating and loss of power. Use the chart to determine
the minimum wire size required in an extension cord. Only
round jacketed cords listed by Underwriter’s Laboratories
(UL) should be used.
When working outdoors with a tool, use an extension
cord that is designed for outside use. This type of cord is
designated with “WA” on the cord’s jacket.
Before using any extension cord, inspect it for loose or
exposed wires and cut or worn insulation.
**Ampere rating (on tool data plate)
0-2.0 2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0
Cord Length Wire Size (A.W.G.)
25' 16 16 16 16 14 14
50' 16 16 16 14 14 12
100' 16 16 14 12 10 —
**Used on 12 gauge - 20 amp circuit.
NOTE: AWG = American Wire Gauge
WARNING:
Keep the extension cord clear of the working area.
Position the cord so that it will not get caught on
lumber, tools or other obstructions while you are
working with a power tool. Failure to do so can
result in serious personal injury.
WARNING:
Check extension cords before each use. If
damaged replace immediately. Never use tool with
a damaged cord since touching the damaged area
could cause electrical shock resulting in serious
injury.
7
Page 8
FEATURES
PRODUCT SPECIFICATIONS
Grinding Wheel Capacity .......................................4-1/2 in.
Spindle Thread ............................................. 5/8 x 11 UNC
No Load Speed ............................................... 10,000/min.
Input ............................120 Volts, 60 Hz, AC only, 8 Amps
Net Weight ................................................................. 5 lbs.
DISC
FLANGE
CLAMP
NUT
SPINDLE
LOCK BUTTON
WRENCH
TOOLLESS
GUARD
GRINDING WHEEL
SIDE HANDLE
PADDLE
SWITCH
LOCK-OFF
BUTTON
8
LOCK-ON
BUTTON
Fig. 1
Page 9
FEATURES
KNOW YOUR ANGLE GRINDER
See Figure 1.
The safe use of this product requires an understanding of
the information on the tool and in this operator’s manual as
well as a knowledge of the project you are attempting. Before
use of this product, familiarize yourself with all operating
features and safety rules.
AUTO-STOP CARBON BRUSHES
When the auto-stop carbon brushes wear down to a predetermined level, the angle grinder automatically switches off,
ruling out the possibility of damage to the armature.
TOOLLESS GUARD
A toolless protective guard deflects sparks and metal chips
during use.
LOCK-OFF BUTTON
Your grinder is equipped with a lock-off button which reduces
the possibility of accidental starting. The lock-off button is
located on the paddle switch. You must push the lock-off
button down in order to depress the paddle switch. The lock
resets each time the paddle switch is released.
LOCK-ON BUTTON
The lock-on button is convenient for continuous grinding for
extended periods of time.
SIDE HANDLE
The side handle can be installed on either side of the grinder
for stabilization and must be used during all operations. In
addition to maintaining safe control during use, the side
handle also provides convenient ease of operation for the
operator.
SPINDLE LOCK BUTTON
The spindle lock button secures the spindle so that only one
wrench is needed to change the grinding wheel.
9
Page 10
ASSEMBLY
UNPACKING
This product requires assembly.
Carefully remove the tool and any accessories from the
box. Make sure that all items listed in the packing list are
included.
Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
Do not discard the packing material until you have care-
fully inspected and satisfactorily operated the tool.
If any parts are damaged or missing, please call
1-866-539-1710 for assistance.
PACKING LIST
Angle Grinder with Guard
Bag
Clamp Nut
Disc Flange
Grinding Wheel
Side Handle
Wrench
Operator’s Manual
TO
LOOSEN
TO
TIGHTEN
SIDE HANDLE
Fig. 2
WRENCH
CLAMP NUT
WARNING:
If any parts are damaged or missing do not operate
this tool until the parts are replaced. Failure to
heed this warning could result in serious personal
injury.
WARNING:
Do not attempt to modify this tool or create
accessories not recommended for use with this
tool. Any such alteration or modification is misuse
and could result in a hazardous condition leading
to possible serious personal injury.
WARNING:
Do not connect to power supply until assembly
is complete. Failure to comply could result in
accidental starting and possible serious personal
injury.
GRINDING WHEEL
TOOLLESS
GUARD
DISC FLANGE
SPINDLE
SPINDLE
LOCK BUTTON
Fig. 3
ATTACHING THE SIDE HANDLE
See Figure 2.
To attach the side handle:
� Unplug the grinder.
� Screw the handle into the side of the gear housing.
NOTE: You can install the handle on either the left or right
side of the grinder, depending on operator preference.
The handle must always be used to prevent loss of
control and possible serious injury.
� Tighten the side handle securely.
10
Page 11
ASSEMBLY
INSTALLING GRINDING WHEEL
See Figure 3.
Thoroughly inspect a new grinding wheel before you install it
on the grinder. Tap lightly around the wheel using a wooden
hammer. Listen carefully to the resulting sounds. Places with
fissures or cracks will result in a different sound. Do not use
a wheel containing fissures or cracks.
When you install a new grinding wheel, carry out a no load
revolution test of approximately one minute with the grinding wheel facing a safe direction, i.e., away from people or
objects.
� Unplug the grinder.
NOTE: The grinder is shipped with the disc flange and
clamp nut attached to the spindle.
� Depress the spindle lock button and rotate the clamp nut
until the spindle locks.
NOTE: To prevent damage to the spindle or spindle lock,
always allow motor to come to a complete stop before
engaging spindle lock.
� Loosen and remove the clamp nut from the spindle. Do
not remove the disc flange.
� Make sure the flats on the bottom of the disc flange are
engaged with the flats on the spindle.
Place the grinding wheel over the spindle.
Thread the clamp nut on the spindle with the flat side of
the nut facing up.
Fit the raised, small diameter portion of the clamp nut
into the hole in the wheel and finger tighten.
WARNING:
Always install a grinding wheel with the depressed
center against the disc flange. Failure to do so
will cause the grinding wheel to crack when
tightening the clamp nut. This could result in
serious personal injury because of loose particles
breaking off and being thrown from the grinder.
Do not overtighten.
Depress the spindle lock button and rotate the wheel
clockwise until the spindle locks in position.
� Tighten the clamp nut securely with the wrench provided.
Do not overtighten.
OPERATION
WARNING:
Do not allow familiarity with tools to make you
careless. Remember that a careless fraction of a
second is sufficient to inflict severe injury.
WARNING:
Always wear safety goggles or safety glasses with
side shields when operating tools. Failure to do so
could result in objects being thrown into your eyes
resulting in possible serious injury.
WARNING:
Do not use any attachments or accessories
not recommended by the manufacturer of this
tool. The use of attachments or accessories not
recommended can result in serious personal
injury.
APPLICATIONS
You may use this tool for the purposes listed below:
Grinding metals
Sanding wood or metal surfaces
11
Page 12
OPERATION
TURNING THE GRINDER ON/OFF
See Figure 4.
To turn the grinder ON:
Push the lock-off button down and depress the paddle
switch.
To turn the grinder OFF:
Release the paddle switch.
LOCK-ON BUTTON
See Figure 4.
This grinder is equipped with a lock-on feature, which is
convenient for continuous grinding for extended periods of
time. To lock-on:
Hold the grinder in front and away from you, keeping the
grinding wheel clear of the workpiece.
Push the lock-off button down and depress the paddle
switch.
Push in and hold the lock-on button, located on the back
of the handle.
Release the paddle switch.
Release the lock-on button and the grinder will continue
running.
To release the lock, depress and release the paddle
switch.
If the lock-on feature is engaged during use and the grinder
becomes disconnected from the power supply, disengage
the lock-on feature immediately.
POSITIONING THE GUARD
See Figures 5 - 7.
The guard on the grinder should be correctly installed
depending on which side the handle is mounted. Never
use the grinder without the guard correctly in place or
when the index arrows are aligned.
PADDLE
SWITCH
INDEX
ARROWS
DEPRESS
LEVER
TO ROTATE
LOCK-OFF
BUTTON
LOCK-ON
BUTTON
Fig. 4
TOOLLESS
GUARD
Fig. 5
WARNING:
Never place the guard so that it is in front of the
grinder. This could result in serious injury because
sparks and loose particles thrown from the grinding
wheel would be directed toward the operator.
Always place the guard in the correct location as
shown.
To adjust the guard:
� Unplug the grinder.
� Depress lever and rotate the guard to its correct position
as shown.
NOTE: Be sure the raised ridge on the guard is seated
in the groove on the bearing cap. Never use the grinder
without the guard in place and properly adjusted.
TOOLLESS
GUARD
SIDE HANDLE ON LEFT SIDE OF GRINDER
Fig. 6
12
Page 13
OPERATION
OPERATING THE GRINDER
See Figure 8.
Always carefully select and use grinding wheels that are
recommended for the material to be ground. Make sure
that the minimum operating speed of any accessory
wheel selected is 10,000/min or more. The grinding wheel
provided with the grinder is suitable for grinding welds,
preparing surfaces to be welded, grinding structural steel,
and grinding stainless steel.
To operate the grinder:
� Secure all work in a vise or clamp to a workbench.
DANGER:
Never use the grinder with the guard removed.
It has been designed for use only with the guard
installed. Attempting to use grinder with guard
removed will result in loose particles being thrown
against the operator resulting in serious personal
injury.
Hold the grinder in front and away from you with
both hands, keeping the grinding wheel clear of the
workpiece.
� Turn on the grinder and let the motor and grinding wheel
build up to full speed.
� Lower the grinder gradually until the grinding wheel con-
tacts the workpiece.
� Keep the grinder tilted at an angle from 5 to 15
degrees.
TOOLLESS
GUARD
SIDE HANDLE ON RIGHT SIDE OF GRINDER
Fig. 7
WARNING:
To prevent loss of control and possible serious
personal injury, always operate the grinder
with both hands, keeping one hand on the side
handle.
Move the grinder continuously at a steady, consistent
pace.
CAUTION:
If the grinder is held in one spot too long, it will
gouge and cut grooves in the workpiece. If the
grinder is held at too sharp an angle, it will also
gouge the workpiece because of concentration of
pressure on a small area.
� Use just enough pressure to keep the grinder from chat-
tering or bouncing.
Fig. 8
NOTE: Heavy pressure will decrease the grinder’s speed and
put a strain on the motor. Normally the weight of the tool
alone is adequate for most grinding jobs. Use light pressure
when grinding jagged edges or loose bolts where there is
the potential for the grinder to snag on the metal edge.
� Lift the grinder away from the workpiece before turning
off the grinder.
13
Page 14
MAINTENANCE
WARNING:
When servi cing use only identical RIDGID
replacement parts. Use of any other parts may
create a hazard or cause product damage.
WARNING:
Always wear safety goggles or safety glasses with
side shields during power tool operation or when
blowing dust. If operation is dusty, also wear a
dust mask.
TO LOOSEN
TOOLLESS
GUARD
TO TIGHTEN
WRENCH
CLAMP NUT
GRINDING
WHEEL
DISC FLANGE
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
WARNING:
Do not at any time let brake fluids, gasoline,
petroleum-based products, penetrating oils, etc.,
come in contact with plastic parts. Chemicals can
damage, weaken, or destroy plastic which may
result in serious personal injury.
Electric tools used on fiberglass material, wallboard, spackling compounds, or plaster are subject to accelerated wear
and possible premature failure because the fiberglass chips
and grindings are highly abrasive to bearings, brushes, commutators, etc. Consequently, we do not recommended using
this tool for extended work on these types of materials. However, if you do work with any of these materials, it is extremely
important to clean the tool using compressed air.
LUBRICATION
All of the bearings in this tool are lubricated with a sufficient
amount of high grade lubricant for the life of the unit under
normal operating conditions. Therefore, no further lubrication
is required.
REPLACING THE GUARD
See Figures 9 - 10.
After extended use, the guard may wear and need replacing.
If you drop the grinder and damage the guard it may also be
necessary for you to replace it.
To replace the guard:
� Unplug the grinder.
WARNING:
Failure to unplug the grinder could result in
accidental starting causing serious injury.
� Depress spindle lock button and rotate clamp nut until
spindle locks.
SPINDLE
SPINDLE
LOCK BUTTON
BEARING CAP
ALIGN INDEX
ARROWS TO
INSTALL OR
REMOVE
DEPRESS
LEVER
TO ROTATE
� Loosen and remove clamp nut from spindle using the
wrench provided.
� Remove grinding wheel and disc flange.
� Align index arrows on guard and bearing cap to remove
guard.
� Place the new guard on the shoulder of the bearing cap
by aligning index arrows on guard and bearing cap.
� Depress the lever and rotate guard to the correct position.
Refer to Positioning the Guard earlier in this manual.
NOTE: Be sure the raised ridge on the guard is seated in
the groove on the bearing cap.
� Reassemble disc flange, grinding wheel, and clamp nut.
Refer to Installing Grinding Wheel earlier in this manual.
� Tighten the clamp nut securely with the wrench provided.
14
Fig. 9
TOOLLESS
GUARD
Fig. 10
Page 15
WARRANTY
RIDGID® HAND HELD AND STATIONARY POWER TOOL
3 YEAR LIMITED SERVICE WARRANTY
Proof of purchase must be presented when requesting warranty service.
Limited to RIDGID® hand held and stationary power tools
purchased 2/1/04 and after. This product is manufactured
by One World Technologies, Inc. The trademark is licensed
from RIDGID, Inc. All warranty communications should be
directed to One World Technologies, Inc., attn: RIDGID Hand
Held and Stationary Power Tool Technical Service at (toll
free) 1-866-539-1710.
90-DAY SATISFACTION GUARANTEE POLICY
During the first 90 days after the date of purchase, if you are
dissatisfied with the performance of this RIDGID® Hand Held
and Stationary Power Tool for any reason you may return
the tool to the dealer from which it was purchased for a full
refund or exchange. To receive a replacement tool you must
present proof of purchase and return all original equipment
packaged with the original product. The replacement tool
will be covered by the limited warranty for the balance of
the 3 YEAR service warranty period.
WHAT IS COVERED UNDER THE 3 YEAR
LIMITED SERVICE WARRANTY
This warranty on RIDGID® Hand Held and Stationary Power
Tools covers all defects in workmanship or materials and normal wear items such as brushes, chucks, motors, switches,
cords, gears and even cordless batteries in this RIDGID
tool for three years following the purchase date of the tool.
Warranties for other RIDGID® products may vary.
HOW TO OBTAIN SERVICE
To obtain service for this RIDGID® tool you must return it;
freight prepaid, or take it in to an authorized service center
for RIDGID® branded hand held and stationary power tools.
You may obtain the location of the authorized service center
nearest you by calling (toll free) 1-866-539-1710 or by logging on to the RIDGID® website at www.ridgid.com. When
requesting warranty service, you must present the original
dated sales receipt. The authorized service center will repair any faulty workmanship, and either repair or replace
any part covered under the warranty, at our option, at no
charge to you.
WHAT IS NOT COVERED
This warranty applies only to the original purchaser at retail
and may not be transferred. This warranty only covers defects arising under normal usage and does not cover any
malfunction, failure or defect resulting from misuse, abuse,
neglect, alteration, modification or repair by other than an
authorized service center for RIDGID® branded hand held
and stationary power tools. Consumable accessories provided with the tool such as, but not limited to, blades, bits
and sand paper are not covered.
RIDGID, INC. AND ONE WORLD TECHNOLOGIES, INC.
MAKE NO WARRANTIES, REPRESENTATIONS OR
PROMISES AS TO THE QUALITY OR PERFORMANCE
OF ITS POWER TOOLS OTHER THAN THOSE SPECIFI
CALLY STATED IN THIS WARRANTY.
ADDITIONAL LIMITATIONS
To the extent permitted by applicable law, all implied warranties, including warranties of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, are disclaimed. Any
implied warranties, including warranties of merchantability
or fitness for a particular purpose, that cannot be disclaimed
under state law are limited to three years from the date of
purchase. One World Technologies, Inc. and RIDGID, Inc.
are not responsible for direct, indirect, incidental or consequential damages. Some states do not allow limitations on
®
how long an implied warranty lasts and/or do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitations may not apply to you. This
warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
One World Technologies, Inc.
P.O. Box 35, Hwy. 8
Pickens, SC 29671
-
15
Page 16
OPERATOR’S MANUAL
4-1/2 in. ANGLE GRINDER
DOUBLE INSULATED
R1001
983000-919
3-24-06 (REV:01)
Customer Service Information:
For parts or service, contact your nearest RIDGID authorized service center. Be
sure to provide all relevant information when you call or visit. For the location of
the authorized service center nearest you, please call 1-866-539-1710 or visit us
online at www.ridgid.com.
The model number of this tool is found on a plate attached to the motor housing.
Please record the serial number in the space provided below. When ordering repair
parts, always give the following information:
Model No.
Serial No.
R1001
16
Loading...