Ricoh feeder User Manual

Download

Operating Instructions

Troubleshooting

When the Machine Does Not Operate As wanted

Troubleshooting When Using the Copy Function

Troubleshooting When Using the Printer Function

Troubleshooting When Using the Scanner Function

Adding paper, Toner and Staples

Clearing Misfeeds

Remarks

Read this manual carefully before you use this machine and keep it handy for future reference. For safe and correct use, be sure to read the

Safety Information in "About This Machine" before using the machine.

Introduction

This manual contains detailed instructions and notes on the operation and use of this machine. For your safety and benefit, read this manual carefully before using the machine. Keep this manual in a handy place for quick reference.

Do not copy or print any item for which reproduction is prohibited by law.

Copying or printing the following items is generally prohibited by local law:

bank notes, revenue stamps, bonds, stock certificates, bank drafts, checks, passports, driver's licenses.

The preceding list is meant as a guide only and is not inclusive. We assume no responsibility for its completeness or accuracy. If you have any questions concerning the legality of copying or printing certain items, consult with your legal advisor.

Important

Contents of this manual are subject to change without prior notice. In no event will the company be liable for direct, indirect, special, incidental, or consequential damages as a result of handling or operating the machine.

Notes:

Some illustrations in this manual might be slightly different from the machine.

Depending on which country you are in, certain units may be optional. For details, please contact your local dealer.

Two kinds of size notation are employed in this manual. With this machine refer to the inch version.

For good copy quality, the supplier recommends that you use genuine toner from the supplier.

The supplier shall not be responsible for any damage or expense that might result from the use of parts other than genuine parts from the supplier with your office products.

Power Source

208-240 V, 50/60 Hz, 20 A or more.

Please be sure to connect the power cord to a power source as shown above. For details about power source, see p.112 “Power Connection”.

Trademarks

Microsoft

, Windows® and Windows NT® are registered trademarks of Microsoft Corporation in the

United States and/or other countries. TrueType is registered trademarks of Apple Computer, Inc.

PostScript

and Acrobat® are registered trademarks of Adobe Systems, Incorporated. PCL is a registered trademark of Hewlett-Packard Company. Bluetooth is a Trademark of the Bluetooth SIG, Inc. (Special Interest Group) and licensed to Ricoh

Company Limited. Other product names used herein are for identification purposes only and might be trademarks of their

respective companies. We disclaim any and all rights to those marks.

The proper names of the Windows operating systems are as follows:

• The product name of Windows

95 is Microsoft® Windows 95.

• The product name of Windows® 98 is Microsoft® Windows 98.

• The product name of Windows

• The product names of Windows

Microsoft Microsoft Microsoft

• The product names of Windows® XP are as follows:

Microsoft Microsoft

• The product names of Windows Server

Microsoft Microsoft Microsoft

• The product names of Windows NT

Microsoft Microsoft

Windows® 2000 Advanced Server

Windows® 2000 Server

Windows® 2000 Professional

Windows® XP Professional

Windows® XP Home Edition

Windows ServerTM 2003 Standard Edition

Windows ServerTM 2003 Enterprise Edition

Windows ServerTM 2003 Web Edition

Windows NT® Server 4.0

Windows NT® Workstation 4.0

Me is Microsoft® Windows Millennium Edition (Windows Me).

2000 are as follows:

2003 are as follows:

4.0 are as follows:

Manuals for This Machine

Refer to the manuals that are relevant to what you want to do with the machine.

❖ About This Machine

Be sure to read the Safety Information in this manual before using the machine. This manual provides an introduction to the functions of the machine. It also explains the control panel, preparation procedures for using the machine, how to enter text, and how to install the CD-ROMs provided.

❖ General Settings Guide

Explains User Tools settings, and Address Book procedures such as registering e-mail addresses, and user codes. Also refer to this manual for explanations on how to connect the machine.

❖ Trouble Shooting

Provides a guide to solving common problems, and explains how to replace paper, toner, staples, and other consumables.

❖ Security Reference

This manual is for administrators of the machine. It explains security functions that the administrators can use to protect data from being tampered, or prevent the machine from unauthorized use. Also refer to this manual for the procedures for registering administrators, as well as setting user and administrator authentication.

❖ Copy/ Document Server Reference

Explains Copier and Document Server functions and operations. Also refer to this manual for explanations on how to place originals.

❖ Printer Reference

Explains Printer functions and operations.

❖ Scanner Reference

Explains Scanner functions and operations.

❖ Network Guide

Explains how to configure and operate the machine in a network environment, and use the software provided. This manual covers all models, and includes descriptions of functions and settings that might not be available on this machine. Images, illustrations, and information about operating systems that are supported might also differ slightly from those of this machine.

❖ Other manuals

•Information

• PostScript3 Supplement

•UNIX Supplement

• Manuals for DeskTopBinder Lite

Note

❒ Manuals provided are specific to machine types.

❒ Adobe Acrobat Reader/Adobe Reader must be installed in order to view the

manuals as PDF files.

❒ For “UNIX Supplement”, please visit our Web site or consult an authorized

dealer.

❒ “PostScript3 Supplement” and “UNIX Supplement” include descriptions of

functions and settings that might not be available on this machine.

Manuals for This Machine ......................................................................................i

How to Read This Manual .....................................................................................1

Symbols .....................................................................................................................1

Names of Major Options ............................................................................................2

1. When the Machine Does Not Operate As wanted

Indicators................................................................................................................3

Panel Tone..............................................................................................................4

Checking Machine Status and Settings...............................................................5

When an Indicator to the Left of a Function Key is Lit....................................... 8

When You Have Problems Operating the Machine.............................................9

When a Job is Not Performed.............................................................................14

2. Troubleshooting When Using the Copy Function

When a Message Appears...................................................................................19

Display During Connect Copy ............................................................................24

If Connect Copy is Cancelled .............................................................................25

If You Cannot Exit from Connect Copy..............................................................26

When You Cannot Make Clear Copies ............................................................... 27

When You Cannot Make Copies As Wanted .....................................................29

When Memory is Full ...............................................................................................33

3. Troubleshooting When Using the Printer Function

When a Message Appears during Installation of the Printer Driver................35

Windows 95/98/Me...................................................................................................35

Windows 2000..........................................................................................................36

Windows XP, Windows Server 2003........................................................................36

Windows NT 4.0.......................................................................................................37

If USB Connection Fails ......................................................................................38

When a Message Appears...................................................................................39

Status Messages......................................................................................................39

Alert Messages ........................................................................................................40

Checking the Error Log ............................................................................................41

When You Cannot Print.......................................................................................42

Other Printing Problems .....................................................................................45

4. Troubleshooting When Using the Scanner Function

When Scanning is Not Done as Expected ......................................................... 51

When You Cannot Send Scanned Files.............................................................52

When Stored Files Cannot be Accessed .................................................................52

When You Cannot Browse the Network to Send a Scan file ...................................52

When the TWAIN Driver Cannot be Started ............................................................52

When Stored Files Cannot be Edited.......................................................................53

When the Network Delivery Function Cannot be Used ............................................53

Operations are not possible when messages appear ..............................................53

iii

When a Message is Displayed............................................................................54

When a Message is Displayed on the Control Panel...............................................54

When a Message is Displayed on the Client Computer...........................................61

5. Adding paper, Toner and Staples

Loading paper ......................................................................................................65

Loading paper into Tray 1 (Tandem Tray) ...............................................................65

Loading Paper into the A3/11” × 17” Tray Unit.........................................................67

Loading Paper into Tray 2 and 3..............................................................................68

Loading Paper into the Large Capacity Tray (LCT) .................................................69

Loading Paper into the Wide Large Capacity Tray (Wide LCT) ............................... 70

Loading Paper into the Multi Bypass Tray (Tray 7).................................................. 71

Loading Paper in the Interposer...............................................................................72

Changing the Paper Size.....................................................................................75

Changing the Paper Size in Tray 2 and 3 ................................................................76

Changing the Paper Size in the Large Capacity Tray (Tray 4 and 5) ......................78

Changing the Paper Size in the Wide Large Capacity Tray .....................................81

Changing to a Size that is Not Automatically Detected............................................84

Pausing Copy When Using Finisher ..................................................................86

Adding Toner........................................................................................................87

Inserting Toner .........................................................................................................89

Used Toner ..............................................................................................................89

Adding Staples.....................................................................................................90

Finisher ....................................................................................................................90

Booklet Finisher (Saddle Stitch)...............................................................................91

6. Clearing Misfeeds

Removing Jammed Paper ...................................................................................93

Locating Jammed Paper ..........................................................................................94

Removing Jammed Paper........................................................................................96

When Z-folded paper is not properly aligned .........................................................105

Removing Jammed Staples ..............................................................................106

Finisher ..................................................................................................................106

Booklet Finisher (Saddle Stitch).............................................................................107

Removing Punch and Staple Waste.................................................................108

Finisher ..................................................................................................................108

7. Remarks

Where to Put Your Machine ..............................................................................109

Machine Environment ............................................................................................109

Moving....................................................................................................................111

Power Connection..................................................................................................112

Access to the Machine...........................................................................................113

Maintaining Your Machine ................................................................................114

Cleaning the Exposure Glass.................................................................................114

Cleaning the Auto Document Feeder.....................................................................114

Earth Leakage Circuit Breaker..........................................................................115

INDEX....................................................................................................... 117

How to Read This Manual

Symbols

This manual uses the following symbols:

Indicates important safety notes.

Ignoring these notes could result in serious injury or death. Be sure to read these notes. They can be found in the “Safety Information” section of About This Machine.

Indicates important safety notes.

Ignoring these notes could result in moderate or minor injury, or damage to the machine or to property. Be sure to read these notes. They can be found in the “Safety Information” section of About This Machine.

Indicates points to pay attention to when using the machine, and explanations of likely causes of paper misfeeds, damage to originals, or loss of data. Be sure to read these explanations.

Indicates supplementary explanations of the machine’s functions, and instructions on resolving user errors.

This symbol is located at the end of sections. It indicates where you can find further relevant information.

[ ]

Indicates the names of keys that appear on the machine’s display panel.

{ }

Indicates the names of keys on the machine’s control panel.

Names of Major Options

Major options of this machine are referred to as follows in this manual:

• Auto Document Feeder → ADF

• Finisher SR5000 → Finisher

• Booklet Finisher BK5000 → Booklet Finisher

1. When the Machine Does Not Operate As wanted

This chapter explains basic troubleshooting procedures that are applicable to all functions of this machine.

Indicators

This section explains Indicators displayed when the machine requires the user to remove misfed paper, add paper, or other perform other procedures.

x: Misfeed indicator Appears when a misfeed occurs.

See p.93 “Removing Jammed Paper”.

B: Add Paper indicator Appears when paper-out condition occurs.

See p.65 “Loading paper”.

D: Add Toner indicator Appears when toner runs out.

See p.87 “Adding Toner”.

d: Add Staple indicator Appears when staples run out.

See p.90 “Adding Staples”.

y: Empty Hole Punch Receptacle indicator

0: Empty Waste Staple Receptacle indicator

L: Service Call indicator Appears when the machine is mulfuncitoning, or needs

M: Open Cover indicator Appears when the front cover, etc, is open.

Appears when the hole punch receptacle is full. See p.108 “Removing Punch and Staple Waste”

Appears when the waste staple receptacle is full. See p.108 “Removing Punch and Staple Waste”

repairing.

When the Machine Does Not Operate As wanted

Panel Tone

The following table explains the meaning of the various beep patterns that the machine produces to alert users about left originals and other machine conditions.

Beep pattern Meaning Cause

Two long beeps. Machine has warmed up. After cooling or being switched on, the

machine has fully warmed up and is ready for use.

Single short beep. Panel/screen input ac-

cepted.

Single long beep. Job completed. A Copier/Document Server Features

Four long beeps. Soft alert. The screen changes back to the initial

Four long beeps repeated five times.

Five short beeps repeated five time.

Soft alert. An original has been left on the expo-

Strong alert. The machine requires user attention

A control panel or screen key was pressed. Single short beeps are produced only when valid keys are pressed.

job has finished.

screen after the machine shifts to energy-saving mode, or the setting was reset at the simplified display.

sure glass, paper is empty, or the punch waste box is full.

because paper have jammed, the toner needs replenishing, or other troubles have occurred.

Note

❒ Users cannot mute the machine's beep alerts. When the machine beeps to alert

users of a paper jam or toner request, if the machine's covers are opened and closed repeatedly within a short space of time, the beep alert might continue, even after normal status has resumed.

Reference

For details about enabling or disabling beep alerts, see “The System Settings”, General Settings Guide.

Checking Machine Status and Settings

You can check the machine's system status.

❖ Maintenance Info

You can check the following items under [Maintenance Info]:

• [Remaining Toner]

Displays the amount of remaining toner.

• [No Staples]

Displays where the staple is empty.

• [Punch Receptacle Full]

Displays whether the hole punch receptacle is full.

• [Waste Staple Receptcl Full]

Displays whether the waste staple receptacle is full.

• [Paper Tray]

Displays the paper type and size loaded in the paper tray.

• [Output Tray Full]

Displays whether the output tray is overloaded.

• [Original Misfeed]

Displays state of and solutions for original misfeeds.

• [Paper Misfeed]

Displays state of and solutions for paper jams.

• [Cover Open]

Indicates whether front cover, duplex unit, etc, is open.

❖ Data Storage

You can check the following items under [Data Storage]:

• [HDD Remaining Memory]

Displays the amount of available hard disk drive memory.

• [HDD File(s)]

Displays the total number of jobs stored in the hard disk drive.

• [Print Job(s)]

Displays the number of jobs for Hold print/Saved print/Locked print/Sample print.

• [Memory Erase Status]

Displays the state of the memory data.

When the Machine Does Not Operate As wanted

❖ Machine Address Info

You can check the following items under [Machine Address Info]:

• [Machine IPv4 Address]

Displays the machine's IPv4 address.

• [Machine IPv6 Address]

Displays the machine's IPv6 address.

❖ Inquiry

You can check the following items under [Inquiry]:

• [Machine Repairs]

Displays the machine number and contact number that are required for service.

• [Sales Representative]

Displays the sales representative's telephone number.

• [Supply Order]

Displays the contact number for placing supply orders.

• [Supply Details]

Displays the name of toner, staples, etc, used on the machine.

A On the control panel, press [System Status] on the control panel.

B Press each tab and check the contents.

Checking Machine Status and Settings

C After checking the information, press [Exit]. The previous screen returns.

Note

❒ [Output Tray Full], [Original Misfeed], [Paper Misfeed], and [Cover Open] appear

only when these errors occur.

❒ For details about how to locate and remove misfeeds, see “Checking

Jammed Paper” or “Removing Jammed Paper”.

Reference

p.94 “Locating Jammed Paper”.

p.93 “Removing Jammed Paper”.

When the Machine Does Not Operate As wanted

When an Indicator to the Left of a Function Key is Lit

When an indicator to the left of a function key lights up, press the corresponding function key. Then, follow the instructions displayed on the control panel.

Problem Cause Solution

Documents and reports do not print out.

An error has occurred. The function whose indi-

The machine is unable to connect to the network.

The paper output tray is full.

There is no copy paper left.

cator is lit is defective.

A network error has occurred.

Remove the paper from the tray.

Add more paper. See p.65 “Loading paper”.

Record the code number shown in the display and contact your service representative. See “When a Message displayed” of each chapter.

You can use other functions normally.

• Check the displayed message and take an appropriate action. See “When a Message displayed” of each chapter.

• Check that the machine is correctly connected to the network, and that the machine is correctly set. See “Network Settings”, General Settings Guide.

• Contact the administrator.

• When the function key is still lit, even if you take the measures above, contact your service representative.

Note

❒ If an error occurs in the function you are using, check the message that ap-

pears on the control panel, and then refer to “When a Message is Displayed” for the relevant function.

Reference

p.19 “Troubleshooting When Using the Copy Function”.

p.35 “Troubleshooting When Using the Printer Function”.

p.51 “Troubleshooting When Using the Scanner Function”.

When You Have Problems Operating the Machine

The following chart gives explanations of common problems and messages.

If other messages appear, follow the instructions displayed.

Important

❒ Check the contact address and Serial No. of Machine shown in the call service

message, and then contact your service representative.

Problem Cause Solution

Although the copier screen appears when the machine is turned on using the main power switch, it cannot be switched to another screen by pressing the {Printer} or {Scanner} key.

The machine has just been turned on and the User Tools screen is displayed, but the User Tools menu has items missing.

The main power indicator continues blinking and does not turn off when pressed.

Functions other than the copier function are not yet ready.

Functions other than the copier function are not yet ready. Time required varies by function. Functions appear in the User Tools menu when they become ready for use.

This occurs in the following cases:

• ADF is open.

• The machine is communicating with external equipment.

• The hard disk is active.

Wait a little longer.

Close ADF, and check if the machine is communicating with a computer.

The display is off. The machine is in Energy

Saver mode.

The display is off. The operation switch is

turned off.

Nothing happens when the operation switch is turned on.

Please wait.” ap-

“ pears.

Please wait.” ap-

“ pears.

The main power switch is turned off.

This message appears when you turn on the operation switch.

This message appears when you change the toner bottle.

Press the {Energy Saver} key to cancel Energy Saver Mode. mode.

Turn on the operation switch.

Turn on the main power switch.

Wait for the machine to get ready.

When the Machine Does Not Operate As wanted

Problem Cause Solution

“Memory is full.

Do you want to store scanned file?

“ appears.

The user code entry screen is displayed.

The Authentication screen appears.

“

” appears.

Self checking...”

You do not have the privileges to use this function.

” is displayed.

The scanned originals exceed the number of sheets/pages that can be stored in the hard disk.

The machine is performing image adjustment operations.

Users are restricted by user management.

Basic Authentication, Windows Authentication, LDAP Authentication or Integration Server Authentication is set.

The use of the function is restricted to authenticated users only.

• Press [Store File] to store pages that

have been scanned. Delete unnecessary files with [Delete File].

• Press [No] if you are not storing pag-

es that have been scanned. Delete unnecessary files with [Delete File].

The machine may perform periodic maintenance during operations. The frequency and duration of maintenance depends on the humidity, temperature, and printing factors such as number of prints, paper size, and paper type. Wait for the machine to get ready.

Enter the user code (up to eight digits), and then press [OK].

Enter your login user name and user password. See “When the Authentication Screen is Displayed”, About This Machine.

Contact the administrator.

You do not have

“

the privileges to use this function.

continues to be displayed even though you have entered a valid user code.

An error message remains, even if misfed paper is removed.

Original images are printed on the reverse side of the paper.

This user code is not allowed to use the function selected.

”

• When a misfeed message appears, it remains until you open and close the cover as required.

• Paper is still jammed in the tray.

You may have loaded the paper incorrectly.

Press the {Energy Saver} key. Confirm that the display goes off, and then press

{

Energy Saver} key again. The display

the will return to the user code entry display. When printing under the copier or

{

printer function, press the key only after printing has finished.

Clear misfed paper, and then open and close the front cover. see p.93 “Clearing Misfeeds”.

Load paper correctly. Place paper in the paper tray with the print side up. Load paper into the bypass tray with the print side down. See p.74 “OrientationFixed Paper or Two-Sided Paper”.

Energy Saver}

When You Have Problems Operating the Machine

Problem Cause Solution

Misfeeds occur frequently.

Misfeeds occur frequently. The tray's end fence may

Misfeeds occur frequently. Paper of undetectable

Misfeeds occur frequently. There is a foreign object

Misfeeds occur frequently. The staple cartridge is not

The tray's side fences may not be locked.

not be set properly.

size has been loaded.

on the finisher tray.

set correctly.

• Remove the paper. See p.93 “Removing Jammed Paper”.

• Check the side fences are locked. See p.75 “Changing the Paper Size”.

• Remove the paper. See p.93 “Removing Jammed Paper”.

• Check the end fence is set properly. See p.75 “Changing the Paper Size”.

• Remove the paper. See p.93 “Removing Jammed Paper”.

• When loading the paper of undetectable size, specify the paper size in “Tray Paper Size”. See “Paper Size: Tray 1-7”, General Settings Guide and “Copy Paper”, About This Machine.

• Remove the paper. See p.93 “Removing Jammed Paper”.

• Do not place anything on the finisher tray. It may cause a paper jam.

The Booklet Finisher requires the saddle stitch stapler cartridge also. See p.90 “Adding Staples”.

Cannot print in duplex mode.

Authentication failed. The entered login user

Authentication failed. The machine cannot per-

The selected file(s) contained file(s) without access privileges. Only file(s) with access privileges will be deleted.

[1 Sided Copy] is selected for Paper Type: Tray 1-7.

You cannot select duplex printing if the paper type is set to [OHP], [Tab Stock], [Translucent] or [Label Pa- per].

name or login password is not correct.

form authentication.

You have tried to delete files without the authority to do so.

Select [2 Sided Copy] for Paper Type: Tray 1-7 See “Paper Size: Tray 1-7”, General Settings Guide.

Select a paper type that allows duplex printing. See “Paper Size: Tray 1-7”, General Settings Guide.

Inquire the user administrator for the correct login user name and login password.

Contact the administrator.

Files can be deleted by the person who created the file. To delete a file which you are not authorized to delete, contact the person who created the file.

When the Machine Does Not Operate As wanted

❖ Document Server

Problem Cause Solution

“

Exceeded max. number of pages per file. Do you want to store the scanned pages as 1 file?

You forgot your password.

You cannot find out what is stored in a file.

” appears.

The number of scanned pages exceeds the capacity per file of the Document Server.

You cannot access a protected file without entering the password.

You may not be able to ascertain the contents of a file simply from the file name.

To store scanned pages as a file, press [Store File]. Scanned data is stored as a file in the Document Server. If you do not want to store scanned pages, press [No]. Scanned data is deleted.

Contact the administrator.

To delete the files stored in the document server, select [Delete All Files in Doc- ument Server]. As this will permanently delete every single file, make sure the document server does not contain any files you want to keep. See “Delete All Files in Document Server”, General Settings Guide.

You can switch the Select File screen between [List] and [Thumbnail] display to check the contents of the file. In list display, the file name, date and time of storage, and user name are shown. In thumbnail display, an image of the stored file appears. You can enlarge the image by pressing [Preview]. Use the Select File screen to check information other than the file name. See “Checking the Details of a Stored Document”, Copy/Document Server Reference.

Memory frequently becomes full.

The document server memory is full.

Delete unnecessary files. On the file selection display, select unnecessary files, and then press [Delete File]. If this does not increase available memory, do the following.

• Switch to the scanner screen, and then delete unnecessary files stored under the scanner function.

• Switch to the printer screen, and then delete unnecessary files stored under Sample Print, Locked Print, Hold Print, or Stored Print.

When You Have Problems Operating the Machine

Problem Cause Solution

You want to check print quality before making a large print run.

Original is being

“

scanned by another function. Please wait.

” appears.

You can print a single copy without specifying the setting again.

Copier or Scanner function is in use.

Check print quality by printing out only the first set using the {Sample Copy} key.

To cancel a job in progress, first press

[Exit], and then press the {Copy} key or {Scanner} key. Next, press the {Stop}

key. When the message “

The Stop

key was pressed. Stop copy-

” press [Stop].

ing?

Cannot display

“

preview of this page.

you can not check the thumb nail image.

” appears, and

The image data may have been corrupted.

Pressing [Exit] displays the preview screen without a thumbnail.

Note

❒ If you cannot make copies as you want because of paper type, paper size, or

paper capacity problems, use recommended paper. See “Copy Paper”, About This Machine.

❒ Using curled paper often causes misfeeds, soiled paper edges, or slipped po-

sitions while performing staple or stack printing. When using curled paper, take the stiffness out of the paper with your hands to straighten out the curl, or load the paper up side down. Also, to prevent paper from curling, lay paper on a flat surface, and do not lean it against the wall.

When the Machine Does Not Operate As wanted

When a Job is Not Performed

If you cannot execute a function, it may be that the machine is being held up by another function.

If you cannot execute a function, terminate any other functions currently active, and then try executing the function again. In certain cases, you can carry out another job (copier, document server, printer, scanner) without canceling the current job being performed. Performing multiple functions simultaneously like this is called “Multi-accessing”.

Combination Chart

❖ Function Compatibility

The chart shows Function Compatibility when print priority is set to “Interleave”. See “Print Priority”, General Settings Guide.

: Simultaneous operations are possible.

: Operation is enabled when the relevant function key is pressed and re-

mote switching (of the scanner/external extension) is done.

: Operation is enabled when the {Interrupt} key is pressed to interrupt the

preceding operation.

→ : Operation is performed automatically once the preceding operation ends. × : The operation must be started once the preceding operation ends. (Simul-

taneous operations are not possible.)

When a Job is Not Performed

Mode after you select Copy

Mode before you select

Copy Operations

for Copying

Operations for Copying

Stapling

Sort

×××

Printer

Interrupt Copying

Operations for Copying

Copying

Stapling

Scanner

Operations for Scanning

Data Reception

Printing

Scanning

TWAIN

Document Server

Scanning

Operations for Document Server

Scanning a Document to Store in Document Server

Printing from Document Server

DeskTopBinder

Printing from Document Server

Web Document Server

Printing

→

Interrupt Copying

Stapling

Sort

Operations for Copying

→

×× ×××

→

Copying ×× →→ ×××→→

Printer Data Reception →→→

Printing →→

Stapling →

Scanner Operations

→→

××

for scanning

Scanning

*2 *2

×××

TWAIN Scanning ЧЧЧЧЧ ЧЧЧЧЧ

*3 *3 *3

When the Machine Does Not Operate As wanted

Mode after you select Copy

Mode before you select

Document Server

Operations for Document Server

Operations for Copying

Stapling

Sort

Printer

Interrupt Copying

Operations for Copying

Copying

Stapling

Scanner

Operations for Scanning

Data Reception

Printing

Scanning

TWAIN

Document Server

Scanning

Operations for Document Server

×××

Scanning a Document to Store in Document Server

Printing from Document Server

DeskTopBinder

Printing from Document Server

Web Document Server

Printing

Scanning a Document to Store in Document Server

Printing from Document Server

DeskTopBinder

Web Document Server

Simultaneous operations are only possible after the preceding job documents are all scanned and [New Job] key appears.

You can scan a document after the preceding job documents are all scanned.

During stapling, printing automatically starts after the current job.

Stapling is not available.

Simultaneous operation become possible after you press [New Job] key.

Printing from Document Server

Printing ×

××

××××

*5 *5 *5

When a Job is Not Performed

Note

❒ Stapling cannot be used at the same time for multiple functions.

❒ If the machine is capable of executing multiple functions simultaneously,

specify which function should have priority in “Print Priority”. This setting is factory-preset to “Display Mode”. For setting of Printing Priority Function, see “Print Priority”, General Settings Guide.

❒ When Finisher or Booklet Finisher is installed on the machine, you can specify

the output tray where documents are delivered. See “Output tray settings”, General Settings Guide.

❒ Operation speed might be reduced if you scan originals while a print job is in

progress.

When the Machine Does Not Operate As wanted

2. Troubleshooting When Using the Copy Function

This chapter explains likely causes of and possible solutions for copier function problems.

When a Message Appears

This section explains the machine's main messages. If other messages appear, follow the instructions they contain.

Important

❒ For messages that are not listed here, see p.9 “When You Have Problems Op-

erating the Machine”.

Message Cause Solution

Cannot detect original size.

Check original orientation.

Check paper size.

Rotate Sort is not available with this paper size.

Improper original is placed.

Original is not placed. Place your originals.

Original is not placed in a proper orientation.

Improper paper size is set.

A size of paper for which Rotate Sort is not available is selected.

Select paper manually, not in Auto Paper Select mode, and do not use Auto Reduce/Enlarge function. See “Sizes difficult to detect”, Copy/Document Server Reference.

Place the original on the exposure glass. See “Placing Originals on the Exposure Glass” and “Sizes difficult to detect”, Copy/Document Server Reference.

Change the orientation of the original.

If you press the {Start} key, copy will start onto the selected paper.

Select the proper paper size. See “Sort”, Copy/Document Server Reference.

Troubleshooting When Using the Copy Function

Message Cause Solution

Cannot punch this paper size.

The Punch function cannot be used with paper size selected.

The following paper sizes are available for Punch mode:

•2 holes:

A3L, B4L, A4KL, B5KL, A5KL, B6L, A6L, 12”×18”L,

11”×17”L, Legal(8

ter(8

/2”×11”)KL, Half Letter

/2”×81/2”)KL, Executive

/4”×101/2”)KL, F/GL

(7 (8”×13”)L, Foolscap (8

Folio (8

/4”×13”)L, 11”×15”L,

/2”×14”)L, Let-

/2”×13”)L,

11”×14”L, 10”×15”L, 10”×14”L,

/4”×14”L, 8”×10”L, 8KL,

8 16KKL. Select one of these sizes.

•3 holes:

A3L, B4L, A4K, B5K, 12”×18”L, 11”×17”L, Letter(8

ecutive (7

/4”×101/2”)K,

/2”×11”)K, Ex-

11”×15”L, 11”×14”L, 8KL, 16KK. Select one of these sizes.

•4 holes: Metric version: A3L, B4L, A4K, B5K, 12”×18”L,

11”×17”L, Letter(8

ecutive (7

/4”×101/2”)K,

/2”×11”)K, Ex-

11”×15”L, 11”×14”L, 10”×15”L, 10”×14”L, 8KL, 16KK. Select one of these sizes. Narrow 2 × 2 version: A3L, B4L, A4KL, B5KL, A5KL, B6L, 12”×18”L,

11”×17”L, Legal(8

/2”×11”)KL, Half Letter

ter(8

/2”×81/2”)KL, Executive

/4”×101/2”)KL, F/GL

(8”×13”)L, Foolscap (8 Folio (8

/4”×13”)L, 11”×15”L,

/2”×14”)L, Let-

/2”×13”)L,

11”×14”L, 10”×15”L, 10”×14”L, 8KL, 16KKL. Select one of these sizes.

Stapling capacity exceeded.

Cannot staple paper of this size.

The number of sheets per set is over the staple capacity.

The Staple function cannot be used with paper size selected.

Check the stapler capacity. See “Supplementary Informations”, Copy/Document Server Reference.

Select a paper size that can be used in Staple mode. See “Supplementary Informations”, Copy/Document Server Reference.

When a Message Appears

Message Cause Solution

Duplex is not available with this paper size.

Maximum number of sets is nn.

(A figure is placed at n.)

File being stored exceeded max. number of pages per file. Copying will be stopped.

Magazine or Booklet mode is not available due to mixed image mode.

A paper size not available in Duplex mode has been selected.

The number of copies exceeds the maximum copy quantity.

The scanned originals have too many pages to store as one document.

You selected the Magazine or Booklet function for originals scanned using different functions, such as copy and printer.

The following paper sizes are available for Duplex mode: A3L, B4L, A4KL, B5KL, A5KL, B6L, A6L, 12”×18”L, 11”×17”L, Legal

/2”×11”)L, Letter (81/2”×11”)KL,

(8 Half Letter (5 tive (7

(8”×13”)L, Foolscap (8”×13”)L, Folio

/4”×13”)L, 11”×15”L, 11”×14”L,

(8 10”×14”L, 8

8KL, 16KKL. Select one of these sizes.

You can change the maximum copy quantity. See “Max. Number of Sets”, General Settings Guide.

Press [Exit], and then store again with an appropriate number of pages.

Make sure originals for the Magazine or Booklet function are scanned using the same function.

/2”×81/2”)KL, Execu-

/4”×101/2”)KL, F/GL

/4”×14”L, 8”×10”L,

Orig. is being scanned by another function. Please wait.

You do not have the privileges to use this function.

Document Server or Scanner function is in use.

This user code is not allowed to use the function selected.

To cancel the job in process, press [Exit], and then press the {Document Server} or {Scanner} key. Next, press the {Stop} key. When the message “

The Clear / Stop key was pressed. Are you sure you want to stop scanning?

Contact the administrator.

If the message continues to be displayed and you cannot switch the screen, press the {Energy Saver} key. Confirm that the display goes off, and then press the {Energy Saver} key again. The display will return to the user code entry display. When printing under the copier or printer function, press the {Energy Saver} key only after printing has finished.

” appears, press [Cancel].

Troubleshooting When Using the Copy Function

Message Cause Solution

Authentication has failed.

The selected file(s) contained file(s) without access privileges. Only file(s) with access privileges will be deleted.

Please wait.

The entered login user name or login password is not correct.

The machine cannot perform authentication.

You have tried to delete files without the authority to do so.

The destination list is being updated from the network using SmartDeviceMonitor for Admin. Depending on the number of destinations to be updated, there may be some delay before you can resume operation. Operations are not possible while this message is displayed.

Inquire the user administrator for the correct login user name and login password.

Contact the administrator.

Files can be deleted by the person who created the file. To delete a file which you are not authorized to delete, contact the person who created the file.

Wait until the message disappears. Do not switch off the power while this message is displayed.

It will be necessary to start over and reload the tab stock to the trays.

❖ Connect Copy

Message Cause Solution

Cannot connect to the sub-machine. Check the status of the sub-machine.

Cannot print from the sub-machine. Check the status of the sub-machine.

A misfeed occurred when unneeded tab stock was ejected.

•The L indicator is lit.

• The hard disk of the sub-machine is malfunctioning.

A paper misfeed has occurred on the sub-machine, or toner or other supplies need to be replenished.

Remove the jammed sheet.

If cycle printing is specified for tab stock sheets, both needed and unneeded tab stock is ejected when copying restarts. Reload the tab stock trays before the new print cycle begins.

After resetting the tab stock pages, press [Exit]. To resume printing, press the {Start} key.

Press [Exit] on the main machine and follow the instructions on the display.

Follow the instructions displayed. For details, see p.87 “Adding Toner”, p.93 “Removing Jammed Paper”, p.106 “Removing Jammed Staples”.

If the sub-machine's display indicates that a cover is open, follow the instructions displayed.

When a Message Appears

Message Cause Solution

Cannot print from the sub-machine. Check the status of the sub-machine.

Sub-machine is in Interrupt mode.

Sub-machine does not have the same paper setting(s).

The Cover Sheet setting(s) of the sub-machine is different from the main machine.

The Slip Sheet setting(s) of the sub-machine is different from the main machine.

The Designation Sheet setting(s) of sub-machine is different from main machine.

The sub-machine's User Tools menu is open.

The sub-machine is in Interrupt mode.

Paper type or tray settings on the two machines do not match.

Cover settings on the two machines do not match.

Slip Sheet settings on the two machines do not match.

Designation Sheet settings on the two machines do not match.

Press the {User Tools} key to close the User Tools menu.

Press the {Interrupt} key on the sub-machine to cancel Interrupt mode.

Make the same settings on both machines.

Sub-machine paper settings must be the same to use

Paper tray settings on the two machines do not match.

Make the same settings on both machines.

this tray.

No stamp data in the sub-machine.

Cannot print from the sub-machine. Sub-machine will be disconnected.

Z-fold is available only when

Stamp data on the submachine has been deleted.

The sub-machine has stopped due to power failure or communication error.

Sort has not been selected with Z-fold.

Reprogram the stamp on the sub-machine.

Continue copying using the main machine.

Select the Sort function.

Sort mode is selected in Connect Copy.

Reference

p.9 “When You Have Problems Operating the Machine”

Troubleshooting When Using the Copy Function

Display During Connect Copy

This section explains about the display during Connect Copy.

Problem Cause Solution

[Connect Copy] is not displayed.

[Connect Copy] appears faded.

The sub-machine's main power is off.

Functions that cannot be used with Connect Copy are selected on the main machine (such as storing or copying the first page of a document in the Document Server).

The main machine is in Interrupt mode.

The [Connect Copy Key Dis- play] setting is off.

The cable connecting the two machines is damaged.

The L is lit. Follow the instructions displayed.

Functions that cannot be used with Connect Copy have been set.

Turn on the sub-machine's main power.

Cancel the functions selected on the main machine.

Press the {Interrupt} key on the sub-machine to cancel Interrupt mode.

Select [Display] for the [Connect Copy Key Display] setting.

Contact your service representative.

Press the {Clear Modes} key to clear the settings.

If Connect Copy is Cancelled

This section explains about causes and remedies when Connect Copy is cancelled.

Problem Cause Solution

The machine cancels Connect Copy.

An error message indicates the main machine has broken down.

The main machine's main power is off, or the operation switch has been pressed.

The sub-machine's main power is off.

The Weekly Timer setting is coming into effect on the main machine.

The L is lit. Copying is not possible. Follow the in-

Turn on the sub-machine's main power or operation switch, and then press [Connect Copy].

A message instructing you to check the sub-machine appears on the display of the main machine. Press [Cancel] to clear Connect Copy. Turn on the sub-machine's main power, press [Connect Copy] and then make your settings again.

Turn on the main machine's operation switch , and then press [Connect Copy].

structions displayed.

Troubleshooting When Using the Copy Function

If You Cannot Exit from Connect Copy

This section explains about causes and remedies if you cannot exit from Connect Copy.

Problem Cause Solution

There is no response when

[

you press

There is no response when you press

Connect Copy].

[

Connect Copy].

[

Connect Copy].

[

Connect Copy].

[

Connect Copy].

[

Connect Copy].

Scanning is in progress. Press the {Stop} key on the main ma-

chine, and then press [Stop].

Copying is in progress. Press the {Stop} key on the main ma-

chine, and then press [Stop].

A paper misfeed has occurred on either the main machine or sub-machine.

A paper misfeed has occurred on either the main or sub-machine.

A paper misfeed has occurred on one of the machine, or toner or other supplies need to be replaced.

Follow the instructions displayed.

For details, see p.93 “Removing Jammed Paper” and p.106 “Removing Jammed Staples”.

If the sub-machine's display indicates that a cover is open, follow the instructions displayed.

To cancel Connect Copy, Press the {Stop} key on the main machine, and then press [Stop].

Follow the instructions displayed.

For details, see p.65 “Loading paper”, p.87 “Adding Toner”, and p.93 “Removing Jammed Paper”.

To cancel Connect Copy, press the {Stop} key on the main machine, and then press [Stop].

There is no response when

[

you press

Connect Copy].

A paper misfeed has occurred during stapling.

Removed the jammed paper.

For details, see p.106 “Removing Jammed Staples”.

To cancel Connect Copy, press the {Stop} key on the main machine, and then press [Stop].

When You Cannot Make Clear Copies

This section explains likely causes of and possible solutions for unclear copies.

Problem Cause Solution

Copies appear dirty. Image density is too high. Adjust the image density. See “Adjust-

ing Copy Image Density”, Copy/Document Server Reference.

Copies appear dirty. Auto Image Density is

not selected.

Adjust the auto density. See “Adjusting Copy Image Density”, Copy/Document Server Reference.

The reverse side of an original image is copied.

A shadow appears on copies if you use pasted originals.

The same copy area is dirty whenever making copies.

Copies are too light. Image density is too light. Adjust the image density. See “Adjust-

Copies are too light. A light copy may result

Image density is too high. Adjust the image density. See “Adjust-

ing Copy Image Density”, Copy/Document Server Reference.

Auto Image Density is not selected.

Image density is too high. Adjust the image density. See “Adjust-

The exposure glass or ADF is dirty.

The original that has already been printed is scanned.

when you use damp or rough grain paper.

Adjust the auto density. See “Adjusting Copy Image Density”, Copy/Document Server Reference.

ing Copy Image Density”, Copy/Document Server Reference.

Change the orientation of the original.

Put mending tape on the pasted part.

Clean them. See p.114 “Maintaining Your Machine”.

Select [Generation Copy], and then begin copying. See “Generation Copy”, Copy/Document Server Reference.

ing Copy Image Density”, Copy/Document Server Reference.

Use the recommended paper. also, use paper that has been stored in the recommended temperature and humidity condition. See “Copy Paper”, About This Machine.

Contact your service representative.

Copies are too light. Toner bottle is almost

empty.

Parts of images are not copied.

The original is not set correctly.

The correct paper size is not selected.

Add toner. See p.87 “Adding Toner”.

Set originals correctly. See “Placing Originals”, Copy/Document Server Reference.

Select the proper paper size.

Troubleshooting When Using the Copy Function

Problem Cause Solution

Images appear only partially.

Black lines appear. The exposure glass is

White lines appear. The exposure glass is

White lines appear. When D is blinking, ton-

Copies are blank. The original is not set cor-

A moiré pattern is produced on copies.

Black spots appear on the copy of a photographic print.

The paper is damp. Use paper that has been stored in the

dirty.

er is beginning to run out.

rectly.

Your original has a dot pattern image or many lines.

Because of high humidity, the photographic print has stuck to the exposure glass.

recommended temperature and humidity condition. See “Copy Paper”, About This Machine.

Clean them. See p.114 “Maintaining Your Machine”.

Add toner. See p.87 “Adding Toner”.

When using the exposure glass, face the originals down. When using the ADF, face them up.

Place the original on the exposure glass at a slight angle.

Place the print on the exposure glass in either of the following ways:

• Place an OHP transparency on the exposure glass, and then place the print on top of the OHP transparency.

• Place the print on the exposure glass, and then place two or three sheets of white paper on top of it. Leave the auto-document feeder (ADF) open when copying.

When You Cannot Make Copies As Wanted

This section explains likely causes of and possible solutions for unclear copies.

❖ Basic

Problem Cause Solution

Misfeeds occur frequently.

Copy paper becomes creased.

The number of sheets loaded exceeds the capacity of the machine.

The paper is damp. Use paper that has been stored in the

The paper is too thick or too thin.

The copy paper is wrinkled or has been folded/creased.

Printed paper is being used.

The paper is damp. Use paper that has been stored in the

Load paper only as high as the upper limit markings on the side fence of the paper tray or bypass tray. See “Copy Paper”, About This Machine.

recommended temperature and humidity condition. See “Copy Paper”, About This Machine.

Use recommended paper. See “Copy Paper”, About This Machine.

Use recommended paper. Use paper that has been stored in the recommended temperature and humidity condition. See “Copy Paper”, About This Machine.

Use recommended paper. Do not use paper that has been already copied or printed onto. See “Copy Paper”, About This Machine.

recommended temperature and humidity condition. See “Copy Paper”, About This Machine.

Copy paper becomes creased.

Copies are not stapled. There are jammed staples

Copies are not stapled. The number of copies ex-

Copies are not stapled. Copy paper is curled. Turn the copy paper over in the tray.

Staples are wrongly positioned.

The paper is too thin. Use recommended paper. See “Copy

Paper”, About This Machine.

Remove jammed staples. See p.106 “Re-

in the stapler.

ceeds the capacity of the stapler.

Originals are not set correctly.

moving Jammed Staples”.

Check the stapler capacity. See “Supplementary Informations”, Copy/Document Server Reference.

Check the correct position to place the originals. See “Staple”, Copy/Document Server Reference.

Troubleshooting When Using the Copy Function

Problem Cause Solution

You cannot combine several functions.

When sorting, the pages are divided into two blocks.

Paper does not output during printing with stapling.

The copy is grayed out or a text pattern appears in the background of the copy.

Images are skewed. The side fences in the pa-

Images are skewed. The paper is feeding in at

Selected functions cannot be used together.

The memory became full in the middle of sorting and the pages were delivered in two blocks.

When you stop printing while using the staple function, paper not stapled during printing may be left in the staple unit.

You have copied a copyguarded document protected from unauthorized copying.

per feed tray is not locked.

a slant.

Check the combination of functions and make the settings again. See “Function Compatibility”, Copy/Document Server Reference.

You can interrupt copying when the memory becomes full. See “Memory Full Auto Scan Restart”, General Settings Guide.

Press the {Clear Modes} key and cancel copy settings, including stapling.

Check the document. See “Using [Data Security for Copying]”, Printer Reference.

Make sure the paper guide is locked. See p.75 “Changing the Paper Size”.

Load the paper correctly. See p.65 “Loading paper”.

❖ Edit

Problem Cause Solution

In Double Copies mode, parts of the original image are not copied.

In Border, Centre, or Centre/ Border mode, parts of the original image are not copied.

In Margin Adjustment mode, parts of the original image are not copied.

Combination of original and copy paper is not correct.

You set a wide erased margin.

Originals are not scanned correctly.

You set a wide erased margin.

Select A3L for A4K originals and A4 for A5 originals.

Make the margin width narrower. You can adjust it between 2 - 99 mm (0.1” -

3.9”). See “Erase Border Width” and

“Erase Centre Width”, General Settings Guide.

Place the originals correctly.

Set a narrower margin with User Tools. You can set the width between 0 - 30 mm (0” - 1.2”).

See “Front Margin: Left/Right”, “Back Margin: Left/Right”, “Front Margin: Top/Bottom” and “Back Margin: Top/Bottom”, General Settings Guide.

When You Cannot Make Copies As Wanted

Problem Cause Solution

In Margin Adjustment mode, parts of the original image are not copied.

In Image Repeat mode, the original image is not copied repeatedly.

❖ Stamp

Problem Cause Solution

The stamp position is wrong.

The stamp is not printed on the back side of sheets when duplex copying.

❖ Combine

There is a lack of margin space on the opposite side of the binding position.

You selected copy paper the same size as the originals, or you did not select the proper reproduction ratio.

The paper orientation is wrong.

The back side stamp position is incorrect for the paper size.

Set a narrower margin with User Tools. You can set the width between 0 - 30 mm (0” - 1.2”).

See “Front Margin: Left/Right”, “Back Margin: Left/Right”, “Front Margin: Top/Bottom” and “Back Margin: Top/Bottom”, General Settings Guide.

Select copy paper larger than the originals or select the proper reproduction ratio.

Check the paper orientation and stamp position.

Reset the back side stamp position. See “Back Side Stamp Position in Duplex”, General Settings Guide.

Problem Cause Solution

You cannot make a book from Booklet or Magazine mode by folding copies.

When using Combine, parts of the image are not copied.

Copies are not in correct order.

You selected a setting (“Open to left”or “Open to right”) that does not match the orientation of originals.

You specified a reproduction ratio that does not match the sizes of your originals and copy paper.

You placed the originals in the incorrect order.

Change the setting. See “Orientation: Booklet, Magazine”, General Settings Guide.

When you specify a reproduction ratio using Manual Paper Select mode, make sure that the ratio matches your originals and the copy paper. Select the correct reproduction ratio before using Combine mode.

When placing a stack of originals in the ADF, the last page should be on the bottom.

If you place an original on the exposure glass, start with the first page to be copied.

Troubleshooting When Using the Copy Function

❖ Duplex

Problem Cause Solution

Cannot print in duplex mode.

Copies are not in correct order.

When using Duplex, copy is made Top to Bottom even though [Top to Top] is selected.

❖ Connect Copy

Problem Cause Solution

You cannot staple, punch, or Z-fold.

You get different copy results from the main and sub-machines.

You have selected a tray which is set to [1 Sided

Copy] in [Tray Paper Settings] in [System Settings].

You placed the originals in the incorrect order.

You placed the originals in the wrong orientation.

The main and sub-machines do not have the same option installed.

The Copy Quality setting differs on the two machines.

Set the tray to [2 Sided Copy] in [Tray Pa- per Settings] in [System Settings]. See “System Settings”, General Settings Guide.

When placing a stack of originals in the ADF, the last page should be on the bottom.

If you place an original on the exposure glass, start with the first page to be copied.

Place the original in the correct orientation. See “Original Orientation”, Copy/Document Server Reference.

Press [Connect Copy] to cancel Connect Copy.

Make the same Copy Quality setting one the two machines.

When You Cannot Make Copies As Wanted

When Memory is Full

This section explains likely causes of and possible solutions for problems related to full memory.

Message Cause Solution

Memory is full.

nn originals have been scanned.

Press [Print] to copy scanned originals. Do not remove remaining originals.

“n” in the message represents a changeable number.

Press [Continue] to scan and copy remaining originals.

❖ Connect Copy

Message Cause Solution

Sub-machine memory is full. Submachine will be disconnected.

The scanned originals exceeds the number of pages that can be stored in memory.

The machine checked if the remaining originals should be copied, after the scanned originals was printed.

The quantity of data exceeds the capacity of the sub-machine.

Press [Print] to copy scanned originals and cancel the scanning data. Press [Stop] to cancel the scanning data and not copy.

To continue copying, remove all copies, and then press [Resume Printing]. To stop copying, press [Stop].

Continue printing on the main machine.

Note

❒ If you set [Memory Full Auto Scan Restart] in User Tools to [On], even if the mem-

ory becomes full, the memory overflow message will not be displayed. The machine will make copies of the scanned originals first, then automatically proceed scanning and copying the remaining originals. In this case, the resulting sorted pages will not be sequential. See “Input / Output”, General Settings Guide.

Troubleshooting When Using the Copy Function

3. Troubleshooting When

Using the Printer Function

This chapter explains likely causes of and possible solutions for printer function problems.

When a Message Appears during Installation of the Printer Driver

This section explains what to do if a message appears when installing the printer driver.

The following describes operations when a message appears during installation of the printer driver. Message number 58 or 34 indicates that the printer driver cannot be installed using Auto Run. Install the printer driver using [Add Printer] or [Install Printer].

Message number 58 appears if there is a newer version of the printer driver already installed.

Windows 95/98/Me

This section explains the procedure under Windows 95/98/Me.

A On the [Start] menu, point to [Settings], and then click [Printers]. B Double-click the Add Printer icon. C Follow the instructions in Add Printer Wizard.

If the CD-ROM drive is D, the source files of the printer driver are stored in the following location:

• RPCS (“Printer Drivers and Utilities” CD-ROM) D:\DRIVERS\RPCS\WIN9X_ME\(Language)\DISK1

• PCL 5e (“Printer Drivers and Utilities” CD-ROM) D:\DRIVERS\PCL5E\WIN9X_ME\(Language)\DISK1

• PCL 6 (“Printer Drivers and Utilities” CD-ROM) D:\DRIVERS\PCL6\WIN9X_ME\(Language)\DISK1

• PostScript 3 (“Scanner Driver and Utilities” CD-ROM) D:\DRIVERS\PS\WIN9X_ME\(Language)\DISK1

If the installer starts, click [Cancel] to quit.

Troubleshooting When Using the Printer Function

Windows 2000

This section explains the procedure under Windows 2000.

A On the [Start] menu, point to [Settings], and then click [Printers]. B Double-click the Add Printer icon. C Follow the instructions in Add Printer Wizard.

If the CD-ROM drive is D, the source files of the printer driver are stored in the following location:

• RPCS (“Printer Drivers and Utilities” CD-ROM) D:\DRIVERS\RPCS\WIN2K_XP\(Language)\DISK1

• PCL 5e (“Printer Drivers and Utilities” CD-ROM) D:\DRIVERS\PCL5E\WIN2K_XP\(Language)\DISK1

• PCL 6 (“Printer Drivers and Utilities” CD-ROM) D:\DRIVERS\PCL6\WIN2K_XP\(Language)\DISK1

• PostScript 3 (“Scanner Driver and Utilities” CD-ROM) D:\DRIVERS\PS\WIN2K_XP\(Language)\DISK1

If the installer starts, click [Cancel] to quit.

Windows XP, Windows Server 2003

This section explains the procedure under Windows XP or Windows Server

2003.

A On the [Start] menu, click [Printers and Faxes]. B Click [Add a printer]. C Follow the instructions in Add Printer Wizard.

If the CD-ROM drive is D, the source files of the printer driver are stored in the following location:

• RPCS (“Printer Drivers and Utilities” CD-ROM) D:\DRIVERS\RPCS\WIN2K_XP\(Language)\DISK1

• PCL 5e (“Printer Drivers and Utilities” CD-ROM) D:\DRIVERS\PCL5E\WIN2K_XP\(Language)\DISK1

• PCL 6 (“Printer Drivers and Utilities” CD-ROM) D:\DRIVERS\PCL6\WIN2K_XP\(Language)\DISK1

• PostScript 3 (“Scanner Driver and Utilities” CD-ROM) D:\DRIVERS\PS\WIN2K_XP\(Language)\DISK1

If the installer starts, click [Cancel] to quit.

When a Message Appears during Installation of the Printer Driver

Windows NT 4.0

This section explains the procedure under Windows NT 4.0.

A On the [Start] menu, point to [Settings], and then click [Printers]. B Double-click the Add Printer icon. C Follow the instructions in Add Printer Wizard.

If the CD-ROM drive is D, the source files of the printer driver are stored in the following location:

• RPCS (“Printer Drivers and Utilities” CD-ROM) D:\DRIVERS\RPCS\NT4\(Language)\DISK1

• PCL 5e (“Printer Drivers and Utilities” CD-ROM) D:\DRIVERS\PCL5E\NT4\(Language)\DISK1

• PCL 6 (“Printer Drivers and Utilities” CD-ROM) D:\DRIVERS\PCL6\NT4\(Language)\DISK1

• PostScript 3 (“Scanner Driver and Utilities” CD-ROM) D:\DRIVERS\PS\NT4\(Language)\DISK1

If the installer starts, click [Cancel] to quit.

Troubleshooting When Using the Printer Function

If USB Connection Fails

This section explains how to troubleshoot a problem related to USB connection.

Problem Cause Solution

The machine is not automatically recognized.

Windows has already configured the USB settings.

Windows Me and the machine cannot be connected.

The USB cable is not connected properly.

Check whether the computer has identified the machine as an unsupported device.

You need to download USB Printing Support for Windows Me.

Turn off the power of the machine, reconnect the USB cable, and then turn it on again.

Open Windows' Device Manager, and then, under [Universal Serial Bus control- lers], remove any conflicting devices. Conflicting devices have a [!] or [?] icon by them. Take care not to accidentally remove required devices. For details, see Windows Help.

When using Windows 2000 / XP or Windows Server 2003, an erroneous device is displayed under [USB Controller] in the [Device Manager] dialog box.

Download USB Printing Support from the supplier's website.

Search the model name you use on the supplier's website, and download USB Printing Support.

When a Message Appears

This section describes the principal messages that appear on the panel display. If a message not described here appears, act according to the message.

Reference

Before turning the main power off, see “Turning On/Off the Power”, About This Machine.

Status Messages

This section describes the machine status messages.

Message Problem

Ready

Printing...

Waiting...

Offline

Please wait.

Resetting job...

Setting change...

Hex Dump Mode

This is the default ready message. The machine is ready for use. No action is required.

The machine is printing. Wait a while.

The machine is waiting for the next data to print. Wait a while.

The machine is offline. To start printing, switch the machine online by pressing {Online} key.

The machine is preparing the development unit. Wait a while.

The machine is resetting the print job. Wait until “

Ready” appears on the display panel.

The machine is setting changing. Wait a while.

In the Hex Dump mode, the machine receives data in hexadecimal format. Turn off the machine after printing, and then turn back on.

Troubleshooting When Using the Printer Function

Alert Messages

This section describes the machine Alert messages.

Message Cause Solution

Cannot connect with the wireless card. Turn the main power switch off, then check the card.

Problems with the

wireless card.

Problems with the

wireless board.

Problems with IEEE 1394 Board.

Problem with Hard Disk.

The entered password is incorrect.

USB has a problem.

• IEEE 802.11b interface unit was not inserted when the machine was turned on, or it was pulled out after the machine turned on.

• The settings are not updated although the unit is detected, or errors are found while accessing the unit.

An error may have occurred in the IEEE 1394 board.

An error has occurred in the hard disk drive.

The password of the encrypted PDF file has been entered incorrectly.

An error has occurred in the USB interface.

Turn off the machine and check the IEEE 802.11b interface unit is inserted correctly. Then, turn the machine on again. If the message appears again, call your service representative.

Turn off the main power switch, and back on again. If the message appears again, contact your service representative.

Enter the correct password.

Turn off the main power switch, and back on again. If the message appears again, contact your service representative.

Hardware Problem: Ethernet

You do not have the privileges to use this function.

Authentication has failed.

Parallel I/F board has a problem.

Printer font error.

An error has occurred in the Ethernet board.

Use of this function is restricted.

• The login user name or password entered is incorrect.

• The machine currently cannot perform authentication.

An error has occurred in the parallel interface board.

An error has occurred in the font settings.

Turn off the main power switch, and back on again. If the message appears again, contact your service representative.

Contact the administrator.

• Check your login user name and password.

• Contact the administrator.

Turn off the main power switch, and back on again. If the message appears again, contact your service representative.

Contact your service representative.

When a Message Appears

Message Cause Solution

Memory Overflow

Maximum capacity of PCL 5e/6 or PostScript 3 list display has been exceeded.

Reduce the value of [Resolution] in the printer driver. Alternatively, select

[Frame Priority] from [Memory Usage] in [System]. If this message continues to

appear after taking these steps, decrease the number of files sent to the machine.

Checking the Error Log

If files could not be stored due to printing errors, identify the cause of the errors by checking the error log on the control panel.

A Press the {Printer} key to display the printer screen.

ANR103S

B Press [Error Log].

An error log list appears.

Note

❒ The most recent 50 errors are stored in the error log. If a new error is added

when there are 50 errors already stored, the oldest error is deleted. However, if the earliest error is a Sample Print, Locked Print, Hold Print, or Stored print error, it is not deleted. The error is stored separately until the number of errors reaches 30.

❒ If the main power switch is turned off, the log is deleted.

Troubleshooting When Using the Printer Function

When You Cannot Print

Use the following procedures if printing does not start even after performing [Print].

Problem Cause Solution

Printing does not start. The power is off. Check the cable is securely plugged

into the power outlet and the machine. Turn on the main power switch.

Printing does not start. The machine is set to “Of-

fline”.

Printing does not start. The cause is displayed on

the display of the control panel.

Printing does not start. The interface cable is not

connected correctly.

Printing does not start. The correct interface ca-

ble is not being used.

Printing does not start. The interface cable was

connected after the machine was switched on.

Printing does not start. If the machine is operat-

ing in an extended wireless LAN, failure to print might result from a weak wireless signal.

Press the {Online} key.

Check the error message or warning status on the display panel and take the required action.

Connect the interface cable securely. If it has a fastener, fasten that securely as well. See “Connecting to the Interfaces”, General Settings Guide.

The type of interface cable you should use depends on the computer. Be sure to use the correct one. If the cable is damaged or worn, replace it. See “Connecting to the Interfaces”, General Settings Guide.

Connect the interface cable before turning on the machine.

To check signal status, press the {User

Tools} key, and then press [System Settings] on the display panel. On the [Interface Settings] tab, select [IEEE 802.11b],

and then press [Wireless LAN Signal]. If signal quality is poor, move the machine to a location where radio waves can pass or remove objects that might cause interference.

(You can check signal status only when using wireless LAN in the infrastructure mode.)

Printing does not start. If the machine is operat-

ing in an extended wireless LAN, SSID settings are incorrect.

Check using the machine's display panel that the SSID is correctly set. See “Network Settings”, General Settings Guide.

When You Cannot Print

Problem Cause Solution

Printing does not start. If the machine is operat-

ing in an extended wireless LAN, the receiver's MAC address may be preventing communication with the access point.

Printing does not start. The extended wireless

LAN has not started.

Printing does not start. The login user name, log-

in password, or driver encryption key is invalid.

Printing does not start. Advanced encryption has

been set using the Extended Security function.

Data-in lamp does not blink or light up.

If the data-in lamp is unlit or not flashing even after performing [Print], the machine has not received the data.

Check access point settings when in the infrastructure mode. Depending on the access point, client access may be limited by MAC address. Also, check there are no problems in transmission between access point and wired clients, and between access point and wireless clients.

Confirm the orange LED is lit, and the green LED is lit or blinks during transmission.

Check the login user name, login password, or driver encryption key.

Check the settings of the Extended Security function with the administrator.

• When the machine is connected to a computer via a cable, check the computer print port settings are correct. See “Confirming the Connection Method”, Printer Reference.

• When it is networked with a computer, Contact the administrator.

The status indicator of the printer is lit.

“

Updating the destination list... Please wait. Specified destination(s) or sender's name has been cleared.

[List / Test Print] is disabled.

Printing does not start when using the extended wireless LAN in Ad-hoc mode.

” appears.

The cause is displayed on the display of the control panel.

The destination list is being updated from the network using SmartDeviceMonitor for Admin.

A mechanical error might have occurred.

The correct Communication mode is not set.

Check the error message on the display panel and take required action. See p.39 “When a Message Appears”.

Wait until the message disappears. Do not switch off the power while this message is displayed. Depending on the number of destinations to be updated, there may be some delay before you can resume operation. Operations are not possible while this message is displayed.

Contact your service representative. See “List/Test Print”, General Settings Guide.

Turn the main power off and back on. See “Turning On/Off the Power”, About This Machine.

Or, change the settings for [System Set- tings], [Interface Settings], and [Network]. See “Network Settings”, General Settings Guide.

If the printing does not start, consult your service representative.

Troubleshooting When Using the Printer Function

❖ When the machine is connected to the computer using the interface cable

The following shows how to check the print port when the data-in lamp does not light up or blink. Check if the print port setting is correct. When it is connected using a parallel interface, connect it to LPT1 or LPT2.

For Windows 95/98/Me

A Click the [Start] button, point to [Settings], and then click [Printers].

B Click the icon of the machine. On the [File] menu, click [Properties].

C Click the [Details] tab.

D In the [Print to the following port:] list, confirm the correct port is selected.

For Windows 2000 or Windows NT 4.0

A Click the [Start] button, point to [Settings], and then click [Printers].

B Click the icon of the machine. On the [File] menu, click [Properties].

C Click the [Ports] tab.

D In the [Print to the following port(s)] list, confirm the correct port is selected.

Windows XP

A Click the [Start] button, and then click [Printers and Faxes].

B Click the icon of the machine. On the [File] menu, click [Properties].

C Click the [Ports] tab.

D In the [Print to the following port(s)] list, confirm the correct port is selected.

Windows Server 2003

A Click the [Start] button, point to [Settings], and then click [Printers and Faxes].

B Click the icon of the machine. On the [File] menu, click [Properties].

C Click the [Ports] tab.

D In the [Print to the following port(s)] list, confirm the correct port is selected.

When Scanning is Not Done as Expected

This section explains causes and remedies when scan results are not as expected.

Problem Cause Solution

The scanned image is dirty.

The image is distorted or out of position.

The scanned image is upside down.

No image results from scanning.

Images are scanned in rotated.

The exposure glass or auto document feeder (ADF) is dirty.

The original was moved during scanning.

The original was not pressed flat against the exposure glass.

The original was placed upside down.

The original was placed with the front and back reversed.

If you set the original with its upper edge backward and save full color/grey scale images as a TIFF or JPEG file, they are scanned in rotated.

Clean these parts. See p.114 “Maintaining Your Machine”.

Do not move the original during scanning.

Make sure that the original is pressed flat against the exposure glass.

Place the original in the correct orientation. See “Placing Originals”, Copy/Document Server Reference.

When the original is placed directly on the exposure glass, the side to be scanned must face down. When the original is fed via the ADF, the side to be scanned must face up. See “Placing Originals”, Copy/Document Server Reference.

When placing a stack of originals in the ADF, place their lower edges first.

See “Various Scan Settings”, Scanner Reference.

The scanned image contains white spaces.

• If you scan originals using functions other than the network TWAIN scanner function, certain paper size and resolution settings may produce scanned images that are larger than the specified size because of margins being added to the sides.

• If the File Format Converter (optional ) is installed, the margins may become wider.

Scanning at a higher resolution may reduce the margins.

Troubleshooting When Using the Scanner Function

When You Cannot Send Scanned Files

The following sections explain likely causes of and solutions for Network Delivery and E-mail Sending-related problems.

When Stored Files Cannot be Accessed

This section explains likely causes of and possible solutions for job access-related problems.

Problem Cause Solution

The stored file is locked and is not accessible.

The file, which is password protected, is locked because the password was incorrectly entered ten times.

Contact the administrator.

When You Cannot Browse the Network to Send a Scan file

This section explains likely causes of and possible solutions for the Browser Network failing to operate when files are sent.

Problem Cause Solution

The network cannot be browsed when specifying the destination folder.

The following machine settings may not be correct:

• IPv4 address

•Subnet Mask

Check the settings. See “Network Settings ”, General Settings Guide.

When the TWAIN Driver Cannot be Started

This section explains likely causes of and possible solutions for the TWAIN driver failing to operate.

Problem Cause Solution

The Scanner Properties dialog box cannot be displayed.

Advanced encryption has been specified in the extended security setting.

For details about the extended security setting, contact an administrator.

When You Cannot Send Scanned Files

When Stored Files Cannot be Edited

This section explains likely causes of and possible solutions for the TWAIN driver failing to operate.

Problem Cause Solution

Stored files cannot be deleted. File names and passwords cannot be changed. Files cannot be redelivered.

Limits have been imposed using the available extended security function.

Contact the administrator.

When the Network Delivery Function Cannot be Used

This section explains likely causes of and possible solutions for the Network Delivery function failing to operate.

Problem Cause Solution

The network delivery function cannot be used.

The delivery software may be an old version or a security setting may be specified.

The network delivery function setting is not correct.

Contact the administrator.

Specify it correctly. See “Settings Required to Use the Network Delivery Scanner”, General Settings Guide.

Operations are not possible when messages appear

This section explains likely causes of and possible solutions for messages that appear and when the machine fails to operate.

Message Cause Solution

Destination list / machine settings are updated. Selected destinations or function settings have been cleared. Please re-select the settings.

Wait until the message disappears. Do not switch off the power while this message is displayed.

Troubleshooting When Using the Scanner Function

When a Message is Displayed

This section explains likely causes of and possible solutions for error messages that may appear on the machine's control panel.

When a Message is Displayed on the Control Panel

This section explains causes and remedies if an error message appears on the display of the control panel.

Important

❒ If a message not described here appears, act according to the message. For in-

formation about how to turn off the main power switch, see About This Machine.

Message Cause Solution

Connection with LDAP server has failed. Check the server status.

LDAP server authentication has failed. Check the settings.

The destination list has been updated. Specified destination(s) or sender's name has been cleared.

Updating the destination list has failed. Try again?

The destination list has been updated. Specified destination(s) or sender's name has been cleared.

A network error has occurred and connection has failed. Try the operation once more.

The user name and password differ from those set for LDAP Authentication.

A specified destination or sender's name was cleared when the destination list in the delivery server was updated.

A network error has occurred.

Try the operation once more. If the message is still shown, the network may be crowded. Check the information of System Settings. See “System Settings”, General Settings Guide.

Make settings correctly for the user name and the password for LDAP server authentication.

Specify the destination or sender's name again.

Check whether the server is connected.

If a destination or sender's name was already selected, re-select it after this message disappears.

When a Message is Displayed

Message Cause Solution

Exceeded max. number of files which can be sent at the same time. Reduce the number of the selected files.

Cannot detect original size. Place original again, then press the Start key.

Exceeded max. No. of results to display. Max.:

You do not have the privileges to use this function.

The number of files exceeded the maximum number possible.

You have loaded paper of a size not shown on the paper size selector.

Search results have exceeded the max. displayable number.

The machine has not been set to allow you to use the function.

Reduce the number of files and send them again.

• Place the original correctly.

• Specify the scan size.

• When placing an original directly on the exposure glass, the lifting/ lowering action of the ADF triggers the automatic original size detection process. Lift the ADF by more than 30 degrees. See “Placing Originals”, Copy/Document Server Reference.

Search again after changing the search conditions.

Contact the administrator.

Exceeded max. number of standby files.Try again after the current file is sent.

Exceeded time limit for LDAP server search. Check the server status.

The specified group contains some destination(s) that do not have access privileges. Do you want to select only the privileged destination(s)?

The maximum number of standby files was exceeded.

A network error has occurred and connection has failed.

The specified group contains some destinations for sending by e-mail and some destinations for sending by Scan to Folder.

There are 100 files waiting in the sending queue for e-mail, Scan to Folder, or delivery functions. Wait until files have been sent.

Try the operation once more. If the message is still shown, the network may be crowded. Check the information of System Settings. See “System Settings”, General Settings Guide.

To select destinations for sending by email, press [Select] for the message dis- played on the e-mail screen. To select destination for sending by Scan to Folder, press [Select] for the message displayed on the Scan to Folder screen.

Troubleshooting When Using the Scanner Function

Message Cause Solution

Cannot find the specified path. Please check the settings.

Exceeded max. number of alphanumeric characters for the path.

The selected file(s) contained file(s) without access privileges. Only file(s) with access privileges will be deleted.

Some of selected files are currently in use. They could not be deleted.

The destination computer name or folder name is invalid.

The maximum number of specifiable alphanumeric characters in a path has been exceeded.

You have tried to delete files without the authority to do so.

You cannot delete a file which is waiting to be transmitted (“Waiting...” status displayed) or whose information is being changed with DeskTopBinder.

Check whether the computer name and the folder name for the destination are correct.

The maximum number of characters which can be entered for the path is 128. Check the number of character you entered, and then enter the path again. See “Transmission function”, Scanner Reference.

The files can be deleted by the file administrator. To delete a file which you are not authorized to delete, contact the administrator.

Cancel transmission (“Waiting...”status cleared) or the DeskTopBinder setting, and then delete the file.

Selected file is currently in use. Cannot change file name.

Selected file is currently in use. Cannot change password.

Selected file is currently in use. Cannot change user name.

You cannot change the name of a file whose status is “Waiting...” or that is being edited with DeskTopBinder.

You cannot change the password of a file whose status is “Waiting...” or that is being edited with DeskTopBinder.

Change the file name after canceling delivery or completing editing.

Delete the password after canceling delivery or completing editing.

A sender's name should be specified before sending e-mail. Send e-mail after specifying the sender's name.

When a Message is Displayed

Message Cause Solution

Connection with the destination has failed. Check the status and connection. To check the current status, press [Scanned Files Status].

Authentication with the destination has failed. Check settings. To check the current status, press [Scanned Files Status].

Sender has not been specified.

Exceeded max. Email size. Sending E-mail has been cancelled. Check [Max. E-mail Size] in Scanner Features.

The correct Network settings are not made.

The entered user name or password was invalid.

The sender's name was not specified.

The maximum e-mail size has been exceeded.

• Check the network settings of the client computer.

• Check that components such as the LAN cable are connected properly.

• Check that the server settings are correct and the server is working properly.

• Check that the user name and password are correct.

• Check that the ID and password for the destination folder are correct.

• A password of 128 or more characters may not be recognized.

A sender's name should be specified before sending e-mail. Send e-mail after specifying the sender's name.

• Increase the size of [Max. E-mail Size].

•Set [Divide & Send E-mail] to [Yes (per Page)] or [Yes (per Max. Size)].

See “Send Settings”, General Settings Guide.

Sending the data has failed. The data will be resent later.

Transmission has failed. To check the current status, press [Scanned Files Status].

A network error has occurred and a file was not sent correctly.

While a file was being sent, a network error occurred and the file could not be sent correctly.

Wait until sending is retried automatically after the preset interval. If sending fails again, contact the administrator.

Try the operation once more. If the message is still shown, the network may be crowded. Contact the administrator. If multiple files were sent, use the Scanned Files Status screen to check for which file the problem occurred.

Troubleshooting When Using the Scanner Function

Message Cause Solution

Transmission has failed. Insufficient memory in the destination hard disk. To check the current status, press [Scanned Files Status].

Output buffer is full. Sending the data has been cancelled. Please try again later.

Exceeded maximum number of file to store. Delete all unnecessary files.

Exceeded max. number of stored files. Cannot send the scanned data as capturing files is unavailable.

Transmission has failed. There was not enough free space on the hard disk of the SMTP server, FTP server, or client computer at the destination.

The file being stored has exceeded the max. number of pages for one file.

Too many files are waiting to be delivered.

Allocate sufficient space.

Specify whether to use the data or not. Scan the pages that were not scanned and store them as a new file. See Storing Files Using the Scanner Function Scanner Reference.

Please try again after they have been delivered.

Exceeded max. number of files which can be used in Document Server at the same time.

Entered protection code for destination is incorrect. Please re-enter.

Entered user code is not correct.

The maximum number of files that can be stored in the document server has been exceeded.

The correct protect destination code was not entered.

The entered password is incorrect.

Check the files stored by the other functions, and then delete unneeded files. See “Document Server”, Copy/Document Server Reference.

Make sure the protection code is correct, and then enter it again. See “Registering a Protection Code”, General Settings Guide.

Check the authentication setting, and then specify a correct password.

When a Message is Displayed

Message Cause Solution

Exceeded max. number of alphanumeric characters.

Authentication has failed.

The entered path is not correct. Please re-enter.

Captured file exceeded max. number of pages per file. Cannot send the scanned data.

Original is being scanned by another function. Please wait.

[

Copier][Document Server]...

The maximum enterable number of alphanumeric characters has been exceeded.

The entered login user name or login password is incorrect.

The entered path format is incorrect.

The maximum number of pages per file has been exceeded.

The machine is using another function such as copying.

Make sure the maximum number of characters which can be entered, and then enter it again. See “Values of various set items for transmission/storage/delivery function”, Scanner Reference.

Check the login user name and login password. The machine is unable to authenticate. Contact an administrator.

Confirm the destination computer and the path, and then enter it again.

Reduce the number of pages in the transmitted file, and then resend the file. See “Storage function”, Scanner Reference.

Retry scanning after the operation with the other function is completed.

E-mail address entered is not correct. Please re-enter.

Memory is full. Scanning has been cancelled. Press [Send] to send the scanned data, or press [Cancel] to delete.

Memory is full. Cannot scan. The scanned data will be deleted.

The entered e-mail address is incorrect.

Because there is not enough free hard disk space in the machine for delivering or sending by e-mail while storing in the Document Server, only some of the pages could be scanned.

Because of insufficient hard disk space, the first page could not be scanned.

Make sure the e-mail address is correct, and then enter it again.

Specify whether to use the data or not.

Try one of the following measures:

• Wait for a while, and then retry the scan operation.

• Reduce the scan area or scanning resolution. See “Setting items for Scan Settings”, Scanner Reference.

• Delete unneeded stored files. See “Deleting a Stored File”, Scanner Reference.

Troubleshooting When Using the Scanner Function

Message Cause Solution

Memory is full. Do you want to store scanned file?

No paper. Load paper of one of the following sizes, then press [Start Printing].

Exceeded max. data capacity.Check the scanning resolution, then reset original(s).

Exceeded max. data capacity.Check scanning resolution, then press Start key again.

Because there is not enough free hard disk space in the machine for storing in the Document Server, only some of the pages could be scanned.

No paper is set in the specified paper tray.

The scanned original exceeded maximum data capacity.

The scanned data exceeded maximum data capacity.

Specify whether to use the data or not.

Load paper of the sizes listed in the message.

Specify the scan size and resolution again. Note that it may not be possible to scan very large originals at a high resolution. See “Relationship between Resolution and File Size”, Scanner Reference.

Exceeded max. page capacity per file. Press [Send] to send the scanned data, or press [Cancel] to delete.

The number of scanned pages exceeded maximum page capacity.

Select whether to send the data so far.

When a Message is Displayed

When a Message is Displayed on the Client Computer

This section explains likely causes of and possible solutions for the main error messages displayed on the client computer when using the TWAIN driver.

Important

❒ If a message not described here appears, act according to the message. For in-

formation about how to turn off the main power switch, see About This Machine.

Message Cause Solution

Clear Misfeed(s) in ADF.

Invalid Winsock version. Please use version 1.1 or higher.

The name is already in use. Check the registered names.

Cannot detect the paper size of the original. Specify the scanning size.

Cannot add any more scanning mode.

A paper misfeed has occurred inside the ADF.

You are using an invalid version of Winsock.

You tried to register a name that is already in use.

The set original was misaligned.

The maximum number of registerable scan modes has been exceeded.

Remove jammed originals, and place them again.

Check whether the originals are suitable to be scanned by the machine.

Install the operating system of the computer or copy Winsock from the operating system CD-ROM.

Use another name.

• Place the original correctly.

• Specify the scan size.

• When placing an original directly on the exposure glass, the lifting/lowering action of the ADF triggers the automatic original size detection process. Lift the ADF by more than 30 degrees.

The maximum number of modes that can be stored is 100. Delete unneeded modes.

Cannot specify any more scanning area.

Call Service Please call your service representative.

Scanner is not available on the specified device.

The maximum number of registerable scan areas has been exceeded.

An unrecoverable error has occurred in the machine.

The TWAIN scanner function cannot be used on this machine.

The maximum number of scanning areas that can be stored is 100. Delete unneeded scanning area.

Call your service representative.

Contact your service representative.

Troubleshooting When Using the Scanner Function

Message Cause Solution

Scanner is not available. Check the scanner connection status.

No response from the scanner.

Error has occurred in the scanner.

Fatal error has occurred in the scanner.

• The machine's main power switch is off.

• The machine is not connected to the network correctly.

The machine or client computer is not connected to the network correctly.

The network is crowded. Wait for a while, and then try to recon-

The application-specified scan conditions have exceeded the setting range of the machine.

An unrecoverable error has occurred on the machine.

• Set the main power switch to “On”.

• Check whether the machine is connected to the network correctly.

• Deselect the personal firewall function of the client computer.

• Use an application such as telnet to make sure SNMPv1 or SNMPv2 is set as the machine’s protocol. See “Network Settings”, General Settings Guide and “Using telnet”, Network Guide.

Check whether the machine or client computer is connected to the network correctly.

nect.

Check whether the scanning settings made with the application exceed the setting range of the machine.

An unrecoverable error has occurred in the machine. Call your service representative.

Cannot connect to the scanner. Check the network Access Mask settings in User Tools.

Scanner is not ready. Check the scanner and the options.

Insufficient memory. Reduce the scanning area.

An access mask is set. Contact the network or scanner admin-

istrator.

The ADF cover is open. Check whether the ADF cover is closed.

Scanner memory is insufficient.

• Reset the scan size.

• Lower the resolution.

• Set with no compression. See TWAIN Driver help.

The problem may be due to the following cause:

• “The Relationship between the Resolution and the Scanning Area” chart in Help for halftone scanning might not always apply. Scanning cannot be performed if large values are set for brightness when using halftone or high resolution.

When a Message is Displayed

Message Cause Solution

Cannot find "XXX" scanner used for the previous scan. "YYY" will be used instead.

(“XXX” and “YYY” indicate scanner names.)

Error has occurred in the scanner driver.

• The main power switch of the previously used scanner is not set to “On”.

• The machine is not connected to the network correctly.

An error has occurred in the driver.

• Check whether the main power switch of the scanner used for the previous scan is turned off.

• Check the previously used scanner is connected to the network correctly.

• Cancel the Personal Firewall of the client computer.

• Use an application such as telnet to make sure SNMPv1 or SNMPv2 is set as the machine’s protocol. See “Network Settings”, General Settings Guide and “Using telnet”, Network Guide.

• Select the scanner used for the previous scan.

• Check whether the network cable is connected correctly to the client computer.

• Check whether the Ethernet board of the client computer is recognized correctly by Windows.

• Check whether the client computer can use the TCP/IP protocol.

Communication error has occurred on the network.

Scanner is in use for other function. Please wait.

Insufficient memory. Close all other applications, then restart scanning.

No User Code is registered. Consult your system administrator.

Any of Login User Name, Login Password or Driver Encryption Key is incorrect.

A communication error has occurred on the network.

A function of the machine other than the scanner function is being used such as the copier function.

Memory is insufficient. • Close all the unnecessary applica-

Access is restricted with user codes.

The entered login user name, password, or driver encryption key was invalid.

Check whether the client computer can use the TCP/IP protocol.

Wait for a while and reconnect.

tions running on the client computer.

• Uninstall the TWAIN driver, and then reinstall it after restarting the computer.

Contact the administrator of the machine.

• Check the login user name, login password, and driver encryption key.

• Permission to use this function has not been granted. Contact the administrator.

Troubleshooting When Using the Scanner Function

Message Cause Solution

Cannot register the user because the scanner's address book is full.

The user has been already registered in the scanner's address book.

Failed to authenticate the user at the authentication server because the address book is full.

Failed to authenticate the user at the authentication server because same user name has been already registered in the address book.

Contact the administrator of the machine.

5. Adding paper, Toner and

Staples

This chapter explains troubleshooting procedures that are applicable to all the machine's functions.

Loading paper

This section explains what to do when paper runs out and needs reloading.

CAUTION:

• When loading paper, take care not to trap or injure your fingers.

Note

❒ Fan the paper before loading.

❒ Straighten curled or warped paper before loading.

❒ When paper in trays that are set to automatically eject unnecessary tab stock

sheets runs out, reload the tab stock from the beginning of the cycle (the first sheet).

❒ For paper types and sizes, see “Recommended Paper Sizes and Types”,

About This Machine.

❒ To load paper in the multi bypass tray (Tray 7), see “Using the Multi Bypass

Tray (Tray 7)”, Copy/Document Server Reference.

Loading paper into Tray 1 (Tandem Tray)

The following procedure explains how to load paper into Tray 1.

Important

❒ When paper loaded in the right side of Tray 1 runs out, paper on the left is

automatically shifted to the right. While the paper is moving, a message instructing you to wait appears. Do not pull out the tray at this time.

❒ For the right stack, align the right edge of the copy paper with the right edge

of the tray. For the left stack, align the left edge of the copy paper to the left edge of the tray.

❒ Tray 1 uses only letter size (8

tact your service representative.

❒ Do not stack paper over the limit mark.

/2"×11"K) paper. If you want to load A4K, con-

Adding paper, Toner and Staples

A Carefully pull out the paper tray until it stops.

ANQ001S

B Square the paper and place it print side down.

• Whole tray pulled out

ANQ002S

• Left half of the tray pulled out

ANQ003S

C Carefully slide the paper tray fully in.

Note

❒ You can load paper even while making copies from Tray 1. You can pull

out the left half of the tray while copying is in.

Loading paper

Loading Paper into the A3/11” × 17” Tray Unit

The following procedure explains how to load paper into the A3/11” × 17” tray unit. To use the A3/11” × 17” tray unit, you must replace Tray 1.

Important

❒ Make sure that the paper stack is flush to the right side fence.

❒ Do not stack paper over the limit mark.

A Carefully pull out the paper tray until it stops.

ANQ008S

B Place the paper in the tray along the edge on the left.

ANQ009S

C Carefully slide the paper tray fully in.

Note

❒ The tray can hold up to 550 sheets.

Adding paper, Toner and Staples

Loading Paper into Tray 2 and 3

The following procedure explains how to load paper into Tray 2 and 3.

Important

❒ Various sizes of paper can be loaded in Tray 2 and 3 by adjusting the positions

of side fence and end fence.

❒ Check the paper edges are aligned at the right side.

❒ Do not stack paper over the limit mark.

A Carefully pull out the paper tray until it stops.

ANQ004S

B Square the paper and load it print side down.

ANQ005S

C Carefully slide the paper tray fully in.

Note

❒ If you load a paper size that is not selected automatically, you will need to

specify the paper size with the control panel. Following paper sizes that are not selected automatically.

❒ The tray can hold up to 550 sheets.

Reference

p.75 “Changing the Paper Size”

p.84 “Changing to a Size that is Not Automatically Detected”

Loading paper

Loading Paper into the Large Capacity Tray (LCT)

The following procedure explains loading paper into the large capacity tray (LCT). The LCT is identified as Tray 4, Tray 5, and Tray 6.

Important

❒ Various sizes of paper can be loaded in Tray 4 and Tray 5 by adjusting the po-

sitions of side fence and end fence.

❒

If you want to change the paper size of Tray 6, contact your service representative.

❒ Check the paper's edges are aligned at the left side.

❒ Do not stack paper over the limit mark.

A Carefully pull out the paper tray until it stops.

ANQ006S

B Load paper into the paper tray by pushing it against to the left side of the

paper tray.

Load the paper print side up.

ANQ007S

C Carefully slide the paper tray fully in.

Note

❒

The tray can hold up to 1,100 sheets in Tray 4 and 5, and 2,800 sheets in Tray 6.

Reference

p.75 “Changing the Paper Size”

p.84 “Changing to a Size that is Not Automatically Detected”

Adding paper, Toner and Staples

Loading Paper into the Wide Large Capacity Tray (Wide LCT)

The following procedure explains loading paper into the wide large capacity tray (Wide LCT). The Wide LCT is identified as Tray 4, Tray 5, and Tray 6.

Important

❒ Various sizes of paper can be loaded in the Wide LCT by adjusting the posi-

tions of side fence and end fence.

❒ Check that the paper edges are aligned at the left side.

❒ Do not load paper above the upper mark in the paper tray

A Carefully pull out the paper tray until it stops.

ANQ060S

B Load paper into the paper tray by pushing the paper to the left side of the

paper tray.

Place paper with printing side up.

ANQ065S

C Carefully slide the paper tray fully in.

Note

❒

The tray can hold up to 1,100 sheets in Tray 4 and 6, and 2,200 sheets in Tray 5.

❒ If you load paper that cannot be automatically detected, specify its size us-

ing the control panel.

Reference

p.75 “Changing the Paper Size”

p.84 “Changing to a Size that is Not Automatically Detected”

Loading paper

Loading Paper into the Multi Bypass Tray (Tray 7)

The following procedure explains loading paper into the multi bypass tray (Tray 7).

Important

❒ Check that the paper edges are aligned at the left side.

❒ The maximum number of sheets you can load into the multi bypass tray (Tray 7)

depend on paper type. The number should not exceed the upper limit.

A Set the side fence to the paper size.

APF028S

B Place paper in the multi bypass tray (Tray 7). C Set the end fence.

ANQ068S

To remove the end fence, slide it to the right.

ANQ069S

Adding paper, Toner and Staples

D Press the elevator switch on the multi bypass tray (Tray 7).

APF030S

The green lamp of the elevator switch is blinking while the tray is going up and down, and keeps lit when it stops.

Press the elevator switch to move down original table if you want to either add paper or remove jammed ones.

Note

❒ The tray can hold up to 550 sheets.

❒ For details about using the multi bypass tray (Tray 7), see “Using the Multi

Bypass Tray (Tray 7)”, Copy/Document Server Reference.

Reference

p.84 “Changing to a Size that is Not Automatically Detected”

Loading Paper in the Interposer

The following procedure explains loading paper into the interposer.

Important

❒ Load paper on the side already printed (the front side). If you are using the

Booklet Finisher (Saddle Stitch), load sheets print side down.

❒ Load paper in the interposer in the same orientation as paper in the paper

tray.

❒ The staple or punching location will be on the left side of the paper, when you

are facing the machine.

❒ Do not place anything on top of or leave documents on the sensor. This may

lead to the paper size not being correctly scanned or paper jams.

❒ When using the Z-fold function, the paper in the interposer must be of the

same size as the prints after they have been Z-folded. If the paper in the interposer is larger than the Z-folded sheets, a misfeed might occur.

Loading paper

A While pressing the release lever, align the side fence with the paper size to

be loaded.

ANQ010S

B Load paper orderly. Tightly fit the side fence to the loaded paper.

ANQ012S

C When loading paper larger than A4, draw out the paper extender.

Note

❒ To set the paper in the interposer, align the orientation of originals in the

ADF as shown below.

ANR026S

❒ When paper is loaded which cannot be detected automatically, the user

must set the paper size on the control panel.

Reference

p.84 “Changing to a Size that is Not Automatically Detected”

Adding paper, Toner and Staples

Orientation-Fixed Paper or Two-Sided Paper

The following describes paper with its orientation and printing surface specified (letterhead paper).

Orientation-fixed (top to bottom) or two-sided paper (for example, letterhead paper, punched paper, or copied paper) might not print correctly, depending on how the originals and paper are placed. Select [On] in [Letterhead Setting] under [Copier / Document Server Features], and then place the original and paper as shown below. See “Letterhead Setting”, General Settings Guide. When printing with the printer function, placement orientation is the same.

For printing using the printer function, load paper in the same orientation.

❖ Paper orientation

Note

❒ Press the {Tray Paper Setting} key, specify Letterhead as “Paper Type” for the

paper tray you want to use. See “Tray Paper Settings”, General Settings Guide.

Changing the Paper Size

This section explains how to change a paper size.

Procedures for changing the paper size differ depending on the tray (tray 1 or other optional paper tray units). Make sure you are following the appropriate procedure before you begin.

Note

❒ Be sure to select the paper size with User Tools. If you do not, misfeeds might

occur.

❒ Fan the paper before loading.

❒ Straighten curled or warped paper before loading.

❒ For details about paper sizes and types, see “Copy Paper”, About This Ma-

chine.

Adding paper, Toner and Staples

Changing the Paper Size in Tray 2 and 3

The following procedure explains how to change a paper size in Tray 2 and 3.

Important

❒ If a paper tray is pushed vigorously when putting it back into place, the posi-

tion of the tray's side fence may slip out of place.

❒ Check that the paper edges are aligned at the right side.

❒ Do not stack paper over the limit mark.

A Check that paper in the paper tray is not being used for copying, and then

pull the tray carefully out until it stops.

ANQ014S

B Remove paper if loaded. C Release the lock on the side fence.

ANQ015S

Changing the Paper Size

D While pressing down the release lever, slide the side fences until they are

aligned the paper size you want to load.

ANQ016S

E Slide the end fence until it is aligned with the size of paper to you want to

load.

ANQ017S

F Square the paper and load it print side up.

Re-lock the side fences again.

ANQ018S

G Carefully slide the paper tray fully in. H Check the size on the display.

Note

❒ If there is space between the side fence and paper, bring the side fence

flush against the edge of the paper.

Adding paper, Toner and Staples

Changing the Paper Size in the Large Capacity Tray (Tray 4 and 5)

The following procedure explains how to change a paper size in the LCT (Tray 4 and 5).

Important

❒ As for changing paper sizes of Tray 6, contact your service representative.

❒ Check that the paper edges are aligned at the left side.

❒ Do not stack paper over the limit mark.

A Carefully pull out the paper tray until it stops.

ANQ006S

B Pull out the screws fixing the side fence.

ANQ020S

C Set the side fences to the size you want.

ANQ021S

D Fasten the side fence with the screws.

ANQ022S

E Set the end fence along the paper size.

Changing the Paper Size

ANQ023S

F Square the paper and set it in the tray.

ANQ024S

Set the paper size selector in the innermost part of the tray to he new paper size.

ANQ025S

Adding paper, Toner and Staples

H Carefully slide the paper tray fully in. I Check the size on the display.

Load A4K, 81/2” × 11”K into the Large Capacity Tray (Tray 4 and 5)

Follow the procedure below to set the end fence for A4K, 81/2” × 11”K.

A Set the end fence according to the paper size.

ANQ076S

A A4K

B 8

/2” × 11”K

B Fasten the end fence using the screw provided.

ANQ077S

Note

❒ When loading index tabs, shift the end fence for A4K, 81/2” × 11”Kto po-

sition before setting the end fence for index tabs.

Changing the Paper Size

Changing the Paper Size in the Wide Large Capacity Tray

The following procedure explains how to change a paper size in the wide large capacity tray (Wide LCT).

Important

❒ Check that the paper edges are aligned at the left side.

❒ Do not stack paper over the limit mark.

A Carefully pull out the paper tray until it stops.

ANQ060S

B Pull out the screws fixing the side fence.

ANQ061S

C Take the grip of the side fence with your fingers, and adjust the side fence

to the paper size.

ANQ062S

Adding paper, Toner and Staples

D Fasten the side fence with the screws.

ANQ063S

E Release the lock on the back fence.

ANQ064S

F Square the paper and set it in the tray.

ANQ066S

Changing the Paper Size

G Tightly fit the back fence to the loaded paper and then re-lock the back

fence again.

ANQ067S

H Carefully slide the paper tray fully in. I Check the size on the display.

Adding paper, Toner and Staples

Changing to a Size that is Not Automatically Detected

If you load a paper size that is not selected automatically, you need to specify the paper size with the control panel. This section explains how to load these paper taking 11”× 15”L as an example.

Important

❒ Following paper sizes that are not selected automatically.

• Tray 2, Tray 3:

11” × 15”L, 11” × 14”L, 10” × 15”L, 10” × 14”L, 8 10”L

/4” × 14”L, 8” ×

• Tray 4, Tray 5, Tray 6 (Wide LCT):

A4L, B5L, A5K, B6L, A6L, 8

/2" × 71/4"KL, 11" × 15"L, 10" × 14"L, 81/4" × 14"L

• Multi Bypass Tray (Tray 7), Interposer:

A4L, B5L, A5K, B6L, 8

× 7

/4"KL, 11" × 15"L, 10" × 14"L, 81/4" × 14"L, 8" × 10"L

/2" × 14"L, 81/2" × 13"L, 81/4" × 13"L, 101/2"

A Press the {Tray Paper Setting} key.

ANR102S

The Tray Paper Settings screen appears.

B Select the tray number on the screen.

/2" × 14"L, 81/2" × 13"L, 81/4" × 13"L,

Changing the Paper Size

C Press [Paper Size] tab.

D Select a combination of the specified paper size and orientation, and then

press [OK].

The paper size and orientation appear.

E Press the {Tray Paper Setting} key.

The initial display is shown.

Note

❒ If you want to print on paper that is selected automatically after printing

on a paper size that is not selected automatically, you must return the setting to “Auto Detect”. Reload the paper, select “Auto Detect” in step setting is returned to “Auto Detect”.

. The

Adding paper, Toner and Staples

Pausing Copy When Using Finisher

You can pause a large volume of copies when using Finisher.

A Press the {Suspend/Resume} key.

The key lights up.

ANQ082S

B Remove the stack of paper from the finisher shift tray.

C Press the {Suspend/Resume} key.

The key turns off, and then copying restarts.

Note

❒ You can suspend copy only when the output tray is specified as the finish-

er shift tray.

ANQ083S

Adding Toner

This section explains adding and storing toner.

WARNING:

• Do not incinerate used toner or toner containers. Toner dust might ignite when exposed to an open flame. Dispose of used toner containers in accordance with local regulations.

CAUTION:

• Keep toner (used or unused) and toner containers out of reach of children. See a doctor immediately if you accidentally swallow toner.

CAUTION:

• If toner or used toner is inhaled, gargle with plenty of water and move into a fresh air environment. Consult a doctor if necessary.

CAUTION:

• If toner or used toner gets into your eyes, flush immediately with large amounts of water. Consult a doctor if necessary.

CAUTION:

• If toner or used toner is swallowed, dilute by drinking a large amount of water. Consult a doctor if necessary.

CAUTION:

• Avoid getting toner on your clothes or skin when removing a paper jam or replacing toner. If your skin comes into contact with toner, wash the affected area thoroughly with soap and water.

• If toner gets on your clothing, wash with cold water. Hot water will set the toner into the fabric and may make removing the stain impossible.

CAUTION:

• Our products are engineered to meet high standards of quality and functionality, and we recommend that you use only the expendable supplies available at an authorized dealer.

CAUTION:

• Open toner cartridges carefully. If you open them forcefully, toner can spill, dirtying your clothes or hands, and possibly resulting in accidental ingestion.

Adding paper, Toner and Staples

Important

❒ Faults may occur if you use toner other than the recommended type.

❒ When adding toner, do not turn off the operation switch. If you do, settings

will be lost.

❒ Always add toner when the machine instructs you.

❒ Do not use recycled toner. This will damage the machine.

❒ During toner adding, the toner bottle is rotating. Do not touch the toner bot-

tle.

❒ If toner remains in the bottle, you cannot remove the bottle. Do not remove

the bottle forcibly.

❒ Be sure to set the new toner bottle in the lower hole first.

❒ Store toner containers in a cool, dry place free from direct sunlight.

❒ Store toner on a flat surface.

Note

❒ If both toner bottles are empty, D will appear. ❒ You can still make about 200 copies after D appears, but replace the toner ear-

ly to copy degradation.

❒ If one of the toner bottle is empty, you can keep copying by using the other

bottle.

❒ You can change the toner bottle during copying.

❒ If toner remains in the bottle, you cannot pull it out.

❒ When you change one toner bottle, do not touch the other one.

❒ Press [System Status] to check contact number for consumables' order. For sys-

tem status, see p.5 “Checking Machine Status and Settings”.

Adding Toner

Inserting Toner

The following describes how to replace toner.

Important

❒ Do not shake the toner bottle with its mouth down after removing it. Residual

toner may scatter.

ANR001S

Used Toner

Toner cannot be re-used.

Bring the stored used container to your sales representative or service representative for recycling through our recycling system. If you discard it on your own, treat it as general plastic waste material.

Adding paper, Toner and Staples

Adding Staples

This section explains what to do when staples need replacing.

CAUTION:

• Keep your hands clear of the booklet finisher tray when pulling out or pushing in the finisher's staple unit. You can trap your fingers if you do not.

Important

❒ Stapling failures or jams may occur if you use a staple cartridge other than

that recommended.

Refill the stapler according to the finisher type. (Check the type if you are unsure.) For details about type of finisher, see “Options”, About This Machine.

Finisher

The following procedure explains how to add staples to the Finisher.

ANR002S

Adding Staples

Booklet Finisher (Saddle Stitch)

The following procedure explains how to add staples to the Booklet Finisher.

ANR003S

Adding paper, Toner and Staples

6. Clearing Misfeeds

This chapter explains what to do when paper or originals misfeed (become jammed inside the machine).

Removing Jammed Paper

CAUTION:

• The inside of the machine could be very hot. Do not touch any parts other than specified in this document when removing misfed paper. Otherwise, it may cause burn injury.

CAUTION:

• The fusing section of this machine might be very hot. Caution should be taken when removing misfed paper.

CAUTION:

• Keep your hands clear of the booklet finisher tray when pulling out or pushing in the finisher's staple unit. You can trap your fingers if you do not.

Important

❒ When clearing misfeeds, do not turn off the operation switch. If you do, your

copy settings will be lost.

❒ To prevent misfeeds, do not leave any torn scraps of paper inside the ma-

chine.

❒ Remove the fusing unit only when necessary.

❒ Contact your service representative if misfeeds occur frequently.

Note

❒ For details about how to locate and remove misfeeds, see “Checking Jammed

Paper” or “Removing Jammed Paper”.

Reference

p.94 “Locating Jammed Paper”.

p.96 “Removing Jammed Paper”.

Clearing Misfeeds

Locating Jammed Paper

If a misfeed happens, remove the misfed paper or original following the procedures stated on the sticker on the rear of main unit front cover.

A misfeed has occurred in the place corresponding to the letter displayed on the control panel.

ANQ030S

Press the key of the section from where you want to remove the jammed paper.

Ricoh feeder User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Introduction

Important

Power Source

Trademarks

Manuals for This Machine

TABLE OF CONTENTS

How to Read This Manual

Symbols

Names of Major Options

Indicators

Panel Tone

Checking Machine Status and Settings

When an Indicator to the Left of a Function Key is Lit

When You Have Problems Operating the Machine

When a Job is Not Performed

When a Message Appears

Display During Connect Copy

If Connect Copy is Cancelled

If You Cannot Exit from Connect Copy

When You Cannot Make Clear Copies

When You Cannot Make Copies As Wanted

When Memory is Full

When a Message Appears during Installation of the Printer Driver

Windows 95/98/Me

Windows 2000

Windows XP, Windows Server 2003

Windows NT 4.0

If USB Connection Fails

When a Message Appears

Status Messages

Alert Messages

Checking the Error Log

When You Cannot Print

Other Printing Problems

When Scanning is Not Done as Expected

When You Cannot Send Scanned Files

When Stored Files Cannot be Accessed

When You Cannot Browse the Network to Send a Scan file

When the TWAIN Driver Cannot be Started

When Stored Files Cannot be Edited

When the Network Delivery Function Cannot be Used

Operations are not possible when messages appear

When a Message is Displayed

When a Message is Displayed on the Control Panel

When a Message is Displayed on the Client Computer

Loading paper

Loading paper into Tray 1 (Tandem Tray)

Loading Paper into Tray 2 and 3

Loading Paper into the Large Capacity Tray (LCT)

Loading Paper into the Wide Large Capacity Tray (Wide LCT)

Loading Paper into the Multi Bypass Tray (Tray 7)

Loading Paper in the Interposer

Orientation-Fixed Paper or Two-Sided Paper

Changing the Paper Size

Changing the Paper Size in Tray 2 and 3

Changing the Paper Size in the Large Capacity Tray (Tray 4 and 5)

Changing the Paper Size in the Wide Large Capacity Tray

Changing to a Size that is Not Automatically Detected

Pausing Copy When Using Finisher

Adding Toner

Inserting Toner

Used Toner

Adding Staples

Finisher

Booklet Finisher (Saddle Stitch)

6. Clearing Misfeeds

Removing Jammed Paper

Locating Jammed Paper