Rice Lake Ishida IGX IGB Operating Manual

Platform Scale

IGX/IGB Series

Kg/Lb Specification

Operation Manual

IGX Series IGB Series

IMPORTANT

• Do not carry out installation, operation, service, or

maintenance until thoroughly understanding the
contents of this manual.

• Keep this manual available at all times for installation,
operation

Manual No. 0202A PN 86545

, service, and maintenance.

PREFACE

Thank you for purchasing an Ishida IGX/IGB Series.
The IGX/IGB Series is a high-performance Platform Scale that weighs items precisely.
This manual explains the operation procedures, cautions for use, etc. of the IGX/IGB Series.
Please read this manual fully so that you can use the IGX/IGB Series safely and effectively.
Failure to follow the instructions in this manual may result in loss or serious injury, damage to the
machine or faulty operation.

NOTE This product cannot be used for certifying weight transactions.

y No part of this manual may be reproduced in any form, by mimeograph or any other means,

without written permission of the publisher.

y Design and specifications are subject to change without notice.

y There may be cases where the contents of this manual may not conform to the actual operations

due to modifications to the machine or other reasons.

y Please convey your comments to your nearest Ishida dealer should you notice any errors or

discrepancies in the contents of this manual.

Copyright © 2003 by Ishida Co., Ltd. All Rights Reserved.

No part of this manual may be reproduced in any form, by mimeograph or any other means, without
written permission of the publisher.

IGX/IGB Series Operation Manual No. 0202A

CONTENTS

Chapter 1 BEFORE OPERATING MACHINE ................................................... 1

1.1 Caution for Handling............................................................................ 2

1.2 Name and Function of Each Part ........................................................ 4

1.3 Installation ........................................................................................... 5

1.4 Start and Stop of Operation ................................................................. 7

1.5 Daily Care............................................................................................ 8

Chapter 2 PRESET FUNCTION ........................................................................ 9

2.1 Presetting the Values......................................................................... 10

2.2 Calling Up the Preset Values............................................................. 14

Chapter 3 WEIGHING ..................................................................................... 15

3.1 Weighing Non-PLUs.......................................................................... 16

3.2 Weighing PLUs.................................................................................. 18

Chapter 4 SETTING MODE............................................................................. 21

4.1 Setting Method .................................................................................. 22

4.2 Set Values List................................................................................... 24

Chapter 5 BATTERY CHECK.......................................................................... 27

5.1 Checking Battery Voltage .................................................................. 28

Chapter 6 APPENDIX ..................................................................................... 31

6.1 Troubleshooting................................................................................. 32

6.2 Specifications .................................................................................... 33

IGX/IGB Series Operation Manual No. 0202A page i

1

BEFORE

OPERATING

MACHINE

1

BEFORE OPERATING MACHINE

IGX/IGB Series Operation Manual No. 0202A page 1

1.1 Caution for Handling

1.1 CAUTION FOR HANDLING

Safety Considerations

To ensure the safe operation of this machine, the general safety considerations below must be
followed:

Grounding
To avoid potential shock hazards, a protective grounding conductor for the machine must be
securely connected.

Do not disassemble or modify the machine

Doing so may result in physical injury or damage to the machine.

Do not remove covers or housing

To avoid personal injury and shock, do not open or remove any covers or casing of the machine
unless specified in this manual.

Do not perform unspecified maintenance

For your own personal safety, do not perform any maintenance procedures which are not specified
in this manual.

Disconnect the power supply before servicing

To ensure your safety, disconnect the power supply before servicing.

Symbols Used in This Manual

This manual uses the following symbols to emphasize important information. Fully understanding
the meaning of the symbols will facilitate the use of this manual.

Symbol Meaning

Indicates information that, if not heeded, could result in faulty operation, damage to
the machine, or relatively serious injury.

Symbol Meaning

Indicates additional information of particular importance.

NOTE

Indicates information to help your understanding of the related text.
Indicates a page to refer to.

page 2 IGX/IGB Series Operation Manual No. 0202A

Avoid Locating the Machine in the Following Places

A place subject to high temperature or high
humidity.

A place exposed to direct sunlight or direct
cold air.

A place where water or other liquids may be
spilled on the machine.

A place subject to a lot of dust or dirt.

1.1 Caution for Handling

1

BEFORE OPERATING MACHINE

A place subject to strong wind.

Power Supply

Always operate the machine with the specified AC
voltage.

A place where the floor or ground is not level
or unstable.

IGX/IGB Series Operation Manual No. 0202A page 3

1.2 Name and Function of Each Part

1.2 NAME AND FUNCTION OF EACH PART

Appearance

Display Unit

IGX Series IGB Series

IGX Series IGB Series

Used to turn the power on or off.

Used to set the scale weight to zero, or increase the value on the display.

Used to set the tare weight, or decrease the value on the display.

Used to move the digit position or finish a setting procedure.

Used to determine or call-up the setting.

page 4 IGX/IGB Series Operation Manual No. 0202A

1.3 INSTALLATION

Assembling the Scale

Remove the two hex-headed bolts from the
bottom of the display pole.

1

Carefully insert the bottom of the display pole
into the base bracket while pulling out the slack

2

in the cables.

1.3 Installation

1

BEFORE OPERATING MACHINE

If the cable insulation is damaged, water may penetrate into the cable and cause
inaccurate weighing, or the core material may corrode, causing the scale to fail.

CAUTION

Tighten the two hex-headed bolts with an Allen
wrench.

3

Bundle the excessive cables with a clamp so as
to prevent cable damage.

4

IGX/IGB Series Operation Manual No. 0202A page 5

1.3 Installation

Carefully carry and place the Weigh Platter over
the Platter Support.

5

Leveling the Scale

Use the level adjuster until the air bubble inside the level is positioned in the center of the circle.

Adjusting the Display Unit Angle

After loosening the display unit tightening knob, adjust the unit to an easy-to see angle. Then
re-tighten the knob.

page 6 IGX/IGB Series Operation Manual No. 0202A

1.4 Start and Stop of Operation

1.4 START AND STOP OF OPERATION

This section explains how to start and stop the machine operation.

Starting Machine Operation

Make sure that nothing is placed on the weigh platter.

1

Press the ON/OFF key to turn on the power. Then, the self-diagnostic display appears and
all display segments are lit.

2

IGX Series IGB Series

Ä

1

BEFORE OPERATING MACHINE

Make sure that the initial display appears and the “ZERO” indicator lights.

3

NOTE If the “ZERO” indicator is not lit, press the ZERO key.

Stopping Machine Operation

Press the ON/OFF key to stop the machine operation.

IGX Series IGB Series

1

IGX Series IGB Series

Ä

NOTE When the scale has not been used for a long time, the scale will be automatically turned off.

IGX/IGB Series Operation Manual No. 0202A page 7

1.5 Daily Care

1.5 DAILY CARE

Daily care will ensure the long life of this machine, and can prevent potential trouble or failure. Also,
cleaning the machine after operation is recommended.

To ensure your personal safety, disconnect the power plug from the outlet before
any servicing or cleaning.

CAUTION

Clean the outer surface of the machine with a soft cloth soaked with a water-diluted neutral
detergent. Then, wipe it with a soft and dry cloth.

CAUTION

`

Do not use thinner or chemicals other than a water-diluted neutral detergent.

page 8 IGX/IGB Series Operation Manual No. 0202A

2

PRESET

FUNCTION

2

PRESET FUNCTION

IGX/IGB Series Operation Manual No. 0202A page 9

2.1 Presetting the Values

2.1 PRESETTING THE VALUES

Selecting the PLU No.

When the power is turned OFF,

1

IGX Series IGB Series

press the ON/OFF key, then the self-diagnosis display appears.

Immediately press the SET key while all display segments are lit.
PLU 1 will be displayed.

2

Ä

IGX Series IGB Series

IGX Series IGB Series

Ä

Repeat to press either the ZERO (+) or TARE (-) key until the desired PLU No. appears on
the display.

3

[Example] Selecting PLU 2

page 10 IGX/IGB Series Operation Manual No. 0202A

or

Ä

IGX Series IGB Series

Setting the Tare Weight

Press the SET key to display the tare weight for the selected PLU.

4

2.1 Presetting the Values

IGX Series IGB Series

Ä

Move the flashing digit to the desired position by pressing the COLUMN key.

5

IGX Series IGB Series

Ä

Increase or decrease the numeric value by pressing the ZERO (+) or TARE (-) key. Then,
press the COLUMN key to determine the value. Repeat this step until completing the entry.

6

[Example] Tare weight 250g

or

Ä

Ä

2

PRESET FUNCTION

Setting the Upper Limit Value

Press the SET key to determine the tare weight and move to the display for setting the upper
limit value.

7

Move the flashing digit to the desired position by pressing the COLUMN key.

Ä

IGX Series IGB Series

IGX Series IGB Series

IGX/IGB Series Operation Manual No. 0202A page 11

2.1 Presetting the Values

Increase or decrease the numeric value by pressing the ZERO (+) or TARE (-) key. Then,
press the COLUMN key to determine the value. Repeat this step until completing the entry.

8

[Example] Upper limit value 1000g

or

Ä

Setting the Lower Limit Value

Press the SET key to determine the upper limit value and move to the display for setting the
lower limit value.

9

Move the flashing digit to the desired position by pressing the COLUMN key.

Ä

IGX Series IGB Series

NOTE If the lower limit value has already been preset, only a value equal to or larger than

this limit value can be set.

IGX Series IGB Series

Ä

page 12 IGX/IGB Series Operation Manual No. 0202A

10

2.1 Presetting the Values

Increase or decrease the numeric value by pressing the ZERO (+) or TARE (-) key. Then,
press the COLUMN key to determine the value. Repeat this step until completing the entry.

[Example] Lower limit value 500g

or

Ä

Ä

IGX Series

IGB Series

2

PRESET FUNCTION

Setting Values for Other PLUs

Press the SET key to determine the lower limit value.

11

Finishing the Setting Procedures

12

Repeat steps 3 through 10 above for setting the values for other PLUs.

NOTE If the upper limit value has already been preset, only a value equal to or less than this

Press the COLUMN key to finish the setting procedure.

limit value can be set.

IGX Series IGB Series

Ä

IGX/IGB Series Operation Manual No. 0202A page 13

2.2 Calling Up the Preset Values

2.2 CALLING UP THE PRESET VALUES

Press and hold the SET key for two seconds.
“PLU 1” will be displayed.

1

IGX Series IGB Series

Ä

(2 sec.)

Press the ZERO (+) or TARE (-) key to select the desired PLU No.

2

IGX Series IGB Series

or

Press the SET key to display the tare weight, the upper limit value, and the lower limit value.

Ä

3

IGX Series IGB Series

Ä

b

b

b

b

NOTE If no tare weight has been set, or if neither the upper limit value nor the lower limit

value has been set, the values set before pressing the SET key will remain active.

page 14 IGX/IGB Series Operation Manual No. 0202A

3

WEIGHING

3

WEIGHING

IGX/IGB Series Operation Manual No. 0202A page 15

3.1 Weighing Non-PLUs

3.1 WEIGHING NON-PLUs

When the power is turned OFF,

1

IGX Series IGB Series

press the ON/OFF key to turn on the power, the self-diagnosis display will start, then stop
at the initial display with “ZERO” indicator lit.

IGX Series IGB Series

Ä

NOTE If “ZERO” indicator is not lit, press the ZERO key to initialize the display.

Place a tare on the weigh platter, and press the TARE key to subtract the weight.
The “NET” indicator will be lit.

2

[Example] Tare weight: 180g

IGX Series IGB Series

Ä

Place an item on the weigh platter.
The display will show the net weight.

3

[Example] Net weight: 2,280g

IGX Series

IGB Series

Ä

page 16 IGX/IGB Series Operation Manual No. 0202A

3.1 Weighing Non-PLUs

When setting “kg” or “lb” select the desired weight unit by pressing the ZERO key and
TARE key at the same time.

4

At the same time

Ä

IGX Series IGB Series

NOTE 1. Either “kg” or “lb” indicator will be lit.

2. This function is available only when nothing is placed on the platter.

3

WEIGHING

IGX/IGB Series Operation Manual No. 0202A page 17

3.2 Weighing PLUs

3.2 WEIGHING PLUs

When the power is turned OFF,

1

IGX Series IGB Series

press the ON/OFF key to turn on the power, the self-diagnosis display appears, then stop
at the initial display with “ZERO” indicator lit.

IGX Series IGB Series

Ä

NOTE If “ZERO” indicator is not lit, press the ZERO key to initialize the display.

Press the SET key, then “PLU 1” appears on the display.

2

Ä

If necessary, repeat to press either the ZERO (+) or TARE (-) key until the desired PLU No.
appears on the display.

IGX Series IGB Series

[Example] Selecting PLU 2

IGX Series IGB Series

or

page 18 IGX/IGB Series Operation Manual No. 0202A

Ä

3.2 Weighing PLUs

Press the SET key to display the tare weight, upper limit value, and lower limit value for the
selected PLU.

3

[Example] Tare weight 250g
Upper limit value 1000g
Lower limit value 500g

IGX Series IGB Series

Ä

b b

b b

3

WEIGHING

Place the item on the weigh platter.
The display will show the net weight.

4

[Example] Net weight 5,970g

b

IGX Series IGB Series

b

Ä

NOTE y When the net weight exceeded the programmed upper weight limit, the “OVER”

indicator will light up.

y When the net weight did not reach the programmed lower weight limit, the

“UNDER” indicator will light up.

y When the net weight is between the upper and lower weight limits, the “ACCEPT”

indicator will light up.

IGX/IGB Series Operation Manual No. 0202A page 19

3.2 Weighing PLUs

After determining the PLU item weight, remove it from the weigh platter.

5

When weighing the same PLU item again, repeat steps 4 and 5 above.

6

NOTE When weighing a different PLU item, repeat steps 2 through 5 above.

To confirm the preset tare, press the COLUMN key.

7

page 20 IGX/IGB Series Operation Manual No. 0202A

4

SETTING

MODE

4

SETTING MODE

IGX/IGB Series Operation Manual No. 0202A page 21

4.1 Setting Method

4.1 SETTING METHOD

When the power supply is turned OFF,

1

press the ON/OFF key to turn ON the power, then immediately press the COLUMN key
while all display segments are lit. Then, the set value number of Setting No. 1 appears.

Ä

Change the set value by pressing the ZERO(+) key or TARE(-) key.
When not changing the setting value, just press the SET key.

2

Ä

IGX Series

IGX Series IGB Series

IGB Series

or

Select the desired Setting No. by pressing the SET key.
Return to step 2 above.

3

Ä

IGX Series IGB Series

Ä

page 22 IGX/IGB Series Operation Manual No. 0202A

Press the COLUMN key to finish the setting procedure.

4

IGX Series IGB Series

Ä

4.1 Setting Method

For descriptions of the setting numbers and the setting conditions of the setting value
numbers, refer to the Set Value List on the following page.

4

SETTING MODE

IGX/IGB Series Operation Manual No. 0202A page 23

4.2 Set Value List

4.2 SET VALUE LIST

 IGX Series

Setting

No.

F03 No function

F04 No function

F05 No function

F06 No function

F07 No function

F08 No function

F09 No function

F10 No function

F11 No function

F12 No function

F13 No function

F14 No function

F15 No function

F16 Buzzer sounding

F17 Automatic power-off time

Description of Setting

(When the buzzer is installed)

Setting

Value No.

00 All key valid F01 Key selection

01 ON/OFF key invalid

00 No function F02 Automatic call of preset number

01 Preset No. 1 is automatically called when

00 During stable weighing outside limit

01 During stable weighing under "OK" condition

02 During stable weighing under "OVER"

03 No buzzer sounds even when key input is

04 Buzzer sounds when key input is made and

05 Buzzer sounds only when key input is made

06 Upper/lower limits discrimination function

00 No function

01 10 minutes

02 20 minutes

03 30 minutes

04 40 minutes

05 50 minutes

06 60 minutes

NOTE Shaded areas are factory default settings.

Setting Condition

(Always scale operation status when the
power is turned ON)

power supply is turned ON.

condition

made.

during stable weighing.

(during stable/unstable weighing)

page 24 IGX/IGB Series Operation Manual No. 0202A

 IGB Series

Setting

No.

F01 No function

No.

F03 No function

F04 No function

F05 No function

F06 No function

F07 No function

F08 No function

F09 No function

F10 No function

F11 No function

F12 No function

F13 No function

F14 No function

F15 No function

F16 No function

F17 Setting automatic power-off time

Description of setting

4.2 Set Value List

Setting

value No.

00 No function provided F02 Function to automatically call preset

01 Preset No. 1 is automatically called

when power supply is ON.

00 No function

01 10 minutes

02 20 minutes

03 30 minutes

04 40 minutes

05 50 minutes

06 60 minutes

Setting condition

4

SETTING MODE

NOTE Shaded areas are factory default settings.

IGX/IGB Series Operation Manual No. 0202A page 25

MEMO

page 26 IGX/IGB Series Operation Manual No. 0202A

Y

K

5

BATTER

CHEC

5

BATTERY CHECK (For IGB Series Only)

For IGB Series Only

IGX/IGB Series Operation Manual No. 0202A page 27

5.1 Checking Battery Voltage

5.1 CHECKING BATTERY VOLTAGE

Press the ON/OFF key, then the self-diagnosis display appears.

1

Ä

Immediately press the TARE key.
The battery check display will appear to check the remaining battery capacity.

2

[Example] Voltage (for reference) 2.8 V

Ä

NOTE Since rechargeable batteries have a normal voltage of 1.2 V (2.4V for two

batteries), their voltage cannot be indicated even when they are fully charged.

[Example] Voltage (for reference) 2.6 to 2.8 V

[Example] Voltage (for reference) 2.4 to 2.6 V

page 28 IGX/IGB Series Operation Manual No. 0202A

5.1 Checking Battery Voltage

[Example] Voltage (for reference) 2.2 to 2.4 V

[Example] Voltage (for reference) 2.0 to 2.2 V

[Example] Voltage (for reference) less than 2.0 V

(when batteries have to be replaced)

5

BATTERY CHECK (For IGB Series Only)

Press any key other than the TARE key to cancel the battery check display.

3

Ä

NOTE When it is necessary to replace the batteries when in use, the battery-replacement

symbol will illuminate and the display indicating all numeric values will appear.

IGX/IGB Series Operation Manual No. 0202A page 29

MEMO

page 30 IGX/IGB Series Operation Manual No. 0202A

A

X

6

6

APPENDIX

PPENDI

IGX/IGB Series Operation Manual No. 0202A page 31

6.1 Troubleshooting

6.1 TROUBLESHOOTING

If an error occurs while using the scale, take appropriate measures according to instructions in the
following table.
If you have any other problems, contact your nearest ISHIDA dealer.

Symptom Measures

The display unit does not indicate any
value or symbol when the ON/OFF key is
pressed.

“0” does not appear after finishing a
display check.

The weight results are different.

y Check the power source.

y Place the scale on a stable flat surface.
y Use the level adjuster to stabilize the scale.
y Protect the scale from strong winds.
y Don’t place the item close to the display pole.

y Place the scale on a stable flat surface or table.
y Check that there is nothing on the scale.
y Use the level adjuster to stabilize the scale.
y Protect the scale from strong winds.

page 32 IGX/IGB Series Operation Manual No. 0202A

6.2 SPECIFICATIONS

 IGX Series

Item Contents

Model Name IGX-60 IGX-150

<OIML Approved>

Weighing Capacity 60 kg / 150 lb 150 kg / 300 lb

Graduation 0.02 kg / 0.05 lb 0.05 kg / 0.1 lb

Accuracy 1/3000

Weigh Platter 550mm (L) x 400mm (W)

Display: ABS resins

Exterior Material

Display Angle Adjust

Weight 16.8kg

Display pole: Aluminum die-cast
Weighing platter: Stainless (SUS304)

Angle adjustable from the horizon (0°) to the front, Knob locking method

6.2 Specifications

Environmental Condition

Power Source

Power Consumption

Display

Tare Subtraction

Preset Function

Upper Limit Range More than the lower limit, within 5 digits (99999)

Lower Limit Range Less than the upper limit (5 digits in case of the upper limit = 0)

Auto Power Off [Setup Mode] None/10min./ 20min./ 30min./ 40min./ 50min./ 60min.

Auto Preset Call-up

Battery Check Mode No

Buzzer Yes

ON/OFF Switch

Option

Temperature from -5°C to +40°C, Relative humidity 80%RH （max.）
without condensation

The required transformer is provided for each 100VAC, 120VAC, 220VAC,
or 240VAC.

120VAC: 46 mA

x VFD

Numerics: 5 + 1/2 digits, Height 29 mm
Mark: Zero point, Now subtracting tare, Stable

x LED

Over, Under, Accept

x Key-in tare
x Preset tare

[Program Mode] 10 PLUs from PLU 1 to PLU 10

(Tare weight, Upper limit, Lower limit)

[Setup Mode] Function “Yes“ / “No“ selection

(PLU 1 is called up when the power is ON.)

6

APPENDIX

IGX/IGB Series Operation Manual No. 0202A page 33

6.2 Specifications

 IGB Series

Item Contents

Model Name IGB-60 IGB-150

<OIML Approved>

Weighing Capacity 60 kg / 150 lb 150 kg / 300 lb

Graduation 0.02 kg / 0.05 lb 0.05 kg / 0.1 lb

Accuracy 1/3000

Weighing Platter 550 mm (L) x 400 mm (W)

Display: ABS resins

Exterior Material

Display Angle Adjust

Weight 16.0 kg (excluding batteries)

Display pole: Aluminum die-cast
Weighing platter: Stainless (SUS304)

Angle adjustable from the horizon (0°) to the front, Knob locking method

Environmental Condition

Power Source

Power Consumption 2.4 to 6VDC: 25mA

Display

Tare Subtraction

Preset Function

Upper Limit Range More than the lower limit, within 5 digits (99999)

Lower Limit Range Less than the upper limit (5 digits in case of the upper limit = 0)

Auto Power Off [Setup Mode] None/10min./ 20min./ 30min./ 40min./ 50min./ 60min.

Auto Preset Call-up

Battery Check Mode Yes

Buzzer No

ON/OFF Switch

Option AC adapter (Dealer option)

Temperature from -5°C to +40°C, Relative humidity 80%RH (max.)
without condensation

Two dray batteries (not attached to machine), or optional AC adapter

[Battery Life]

Conditions: No option, Temperature 20°, Relative humidity 60%RH
Two “D” size alkaline batteries (Approx. 500H continuous use)

x LCD

Numerics: 6 digits, Height 25 mm
Mark: Battery. Zero point, Now subtracting tare, Stable, Weight unit

(kg･lb), Over, Under, Accept

x Key-in tare
x Preset tare

[Program Mode] 10 PLUs from PLU 1 to PLU 10

(Tare weight, Upper limit, Lower limit)

[Setup Mode] Function “Yes”/”No” selection

(PLU 1 is called up when the power is ON.)

page 34 IGX/IGB Series Operation Manual No. 0202A

Design and specifications are subject to change without notice.

44 SANNO-CHO, SHOGOIN, SAKYO-KU
KYOTO, 606-8392 JAPAN
PHONE: [phone]
FACSIMILE: 81-75-751-1634
URL: http://www.ishidajapan.com