P6SP-072 (6 Ton), -090 (7.5 Ton), & -120 (10 Ton) Series
USER’S MANUAL
Single Package Electric Heating / Electric Cooling Rooftop Unit
IMPORTANT! Please read all information in this manual thoroughly and become familiar with the capabilities and use
of your appliance before attempting to operate or maintain this unit. Pay attention to all safety warnings and any other
special notes highlighted in the manual. Safety markings are used frequently throughout this manual to designate
a degree or level of seriousness and should not be ignored. WARNING indicates a potentially hazardous situation
that if not avoided, could result in personal injury or death. CAUTION indicates a potentially hazardous situation that
if not avoided, may result in minor or moderate injury or property damage. Keep this literature where you have easy
access to it in the future. If a problem occurs, check the instructions and follow recommendations given. If these
suggestions don’t eliminate your problem, call your servicing contractor. Do not attempt to service this unit yourself!
P6SP-090 Shown
!
WARNING:
• Under no circumstances should the appliance owner attempt to install and/or service this
equipment. Some local codes require licensed installation / service personnel for this
type of equipment. Improper service, adjustment, or maintenance may cause explosion,
fi re, electrical shock or other hazardous conditions which may result in personal injury or
property damage.
• Read these instructions thoroughly before using the equipment. Follow all precautions and
warnings contained within these instructions and on the unit.
• Improper installation, adjustment, alteration, service, or maintenance can cause personal
injury or property damage. Refer to this manual. For assistance or additional information,
consult a qualifi ed installer or service agency.
• Do not store or use gasoline or other fl ammable vapors and liquids in the vicinity of this or
any other appliance.
DO NOT DESTROY. PLEASE READ CAREFULLY AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.
ABOUT THE ROOFTOP UNIT
This single package electric heating / electric cooling
rooftop unit has been designed and built to provide
many years of safe and dependable comfort, providing
it is properly installed and maintained. With regular
maintenance, this unit will operate satisfactorily year after
year. Abuse, improper use, and/or improper maintenance
can shorten the life of the appliance and create unsafe
hazards. A regular service and maintenance schedule
should be established to ensure effi cient and safe operation
of the unit. See System Maintenance on page 3.
IMPORTANT SAFETY INFORMATION
WARNING:
To avoid possible equipment damage, fi re, or
personal injury, the following instructions must
be observed regarding unit maintenance and
operational procedures.
OPERATING INSTRUCTIONS
Thermostat styles vary. Some models may not include
the AUTO mode and others will have the AUTO in place
of the HEAT and COOL. Others may include all three.
Please refer to the thermostat’s User Manual for detailed
programming instructions..
The thermostat should be mounted about 5 feet above the
fl oor on an inside wall and not on an outside wall or other
location where its operation may be adversely affected by
radiant heat from fi replaces, sunlight, or lighting fi xtures,
and convective heat from warm air registers or electrical
appliances.
Cooling Operation
1. Set the thermostat system mode to COOL and the
thermostat fan mode to AUTO. See Figure 1.
2. Set the thermostat temperature selector to the desired
temperature level. The outdoor fans, compressors, and
indoor blower will all cycle on and off to maintain the
indoor temperature at the desired cooling level.
• To achieve optimum performance and minimize
equipment failure, it is recommended that periodic
maintenance be performed on this unit. The ability
to properly perform maintenance on this equipment
requires certain mechanical skills and tools. Please
consult your dealer for maintenance information and
availability of maintenance contracts.
• The area around the unit and the vicinity of any other
appliances must be kept clear and free of combustible
materials, gasoline, and other fl ammable vapors and
liquids. Do not store or use fl ammable items such as
paint, varnish, or strippers in the vicinity of the unit.
• Do not use the area around the unit as a storage area.
This area must be kept clean and clear of loose or
exposed insulation materials. Examine the unit’s area
when it is installed or when insulation is added, since
some insulation materials may be combustible.
• Do not use this appliance if any part has been under
water. Immediately call a qualifi ed service technician
to inspect the unit and to replace any part of the
electrical control system that has been under water.
• Familiarize yourself with the controls that shut off
the electrical power to the unit. If the unit needs to
be shut down for an extended period of time, turn
off the electrical power. For your safety always turn
off the electrical power before performing service or
maintenance on the furnace.
• Do not block or obstruct air openings on the unit or air
openings supplying the area where it is installed.
• The duct connections must be physically sound and
sealed to the unit’s casing. The return air and circulating
air ductwork must not be connected to any other heat
producing device such as a fi replace insert, stove, etc.
Doing so may result in fi re, explosion, personal injury,
carbon monoxide poisoning, or property damage.
Heating Operation
1. Set the thermostat system mode to Heat and the
thermostat fan mode to AUTO. See Figure 1.
2. Set the thermostat temperature selector to the desired
temperature level. The indoor blower and optional
electric heat module will cycle on and off to maintain
the indoor temperature at the desired heating level.
Operating the Indoor Blower Continuously
Set the thermostat fan mode to ON (or CONT on some
thermostat models). See Figure 1.
The indoor blower will start immediately, and will run
continually until the fan switch is reset to AUTO.
The continuous indoor blower operation can be obtained
with the thermostat system switch set in any position,
including OFF. NOTE: Continuous indoor blower operation
is typically used to circulate the indoor air to equalize a
temperature imbalance due to a solar load, occupancy
loads, or mechanical equipment operation.
Fan
Mode
Figure 1. Digital Thermostat
System
Mode
Temperature
Selector
2
System Shutdown
Set the thermostat system mode to OFF and the thermostat
fan mode to AUTO. See Figure 1. NOTE: The system will
not operate, regardless of the thermostat temperature
selector’s setting.
SYSTEM MAINTENANCE
CAUTION:
Air Filters
WARNING:
Never operate the unit without a fi lter in the
return air system. Dust and lint in the return
air can build up on the internal components,
resulting in loss of efficiency, equipment
damage, and possible fi re risk.
Verify all electrical power to the unit is shut off
before performing the following recommended
maintenance.
Proper maintenance is most important to achieve the best
performance from the appliance and should be performed
by a qualifi ed service technician at least once a year.
Follow the maintenance schedule and the instructions
below for years of safe, trouble free operation.
• Do not place combustible materials on or against the
cabinet.
• Do not store gasoline or any other fl ammable vapors
and liquids in the vicinity of the unit.
• Annually inspect the physical support of the unit to
ensure that it is physically sound without sagging,
cracks, gaps, etc., around the base so as to provide a
seal between the support and the base.
• Annually inspect the return-air connection to ensure
that it is physically sound and is still sealed to the
casing of the unit. Also inspect the unit, ductwork, and
vent system for signs of physical deterioration.
• Always replace the doors on the unit after servicing.
Do not operate the unit without all doors and covers
in place. Avoid operating the unit when windows and
doors are open.
Regular Cleaning
CAUTION:
DO NOT touch any of the internal electrical
components while cleaning the unit.
• Remove any leaves and grass clippings from the
outdoor coil. IMPORTANT: Be careful not to damage
the aluminum fi ns.
• Check for and remove any obstructions such as twigs,
sticks, etc.
• Clean the blower compartment regularly during the
heating and cooling seasons to remove any dust
that may have accumulated in the compartment or on
the blower and motor. Buildup of dust on the blower
and motor can create excessive loads on the motor
resulting in higher than normal operating temperatures
and possible shortened service life.
P6SP Series
2 inch disposable fi lters. The fi lters should be checked
periodically and replaced (or cleaned) when necessary
with fi lters of the same dimensional size. Replace using
disposable fi lters with a minimum airfl ow rating of
500 FPM or permanent fi lters only.
• The fi lter rack is fi eld adjustable to accommodate
1” permanent fi lters. DO NOT use 1” disposable
fi lters in these units.
• Always replace the fi lter access panels after
changing or cleaning the fi lters. DO NOT operate
unit without the fi lter access panels in place.
• It is very important to replace or clean the fi lter(s)
installed in the return air duct of this system. A
clogged fi lter could cause airfl ow related problems
and reduce the overall effi ciency of your unit.
Always replace disposable fi lter(s) installed in
your system only with the same size dimensional
fi lters that are being replaced.
• Filters must be ULC approved or equivalent for
use in Canada.
units are factory equipped with pleated
IMPORTANT NOTES:
Motor Lubrication
The motors for the circulating air blower and outdoor fan
are pre-lubricated and sealed by the manufacturer. No
further oiling is required for the life of this product.
TROUBLESHOOTING
Before you call a Technician, check the following:
• Check the thermostat setting. Make sure the system
mode and temperature settings are correct.
• Check the electrical panel for tripped circuit breakers.
• Check the fi lters for dust accumulation.
• Check the unit and make sure it is clean and not
covered with grass or leaves.
• If the items above don’t resolve your problems, then
call your nearest service technician.
3
WARRANTY INFORMATION
A warranty certifi cate with full details is included with the equipment. Carefully review these responsibilities with your
dealer or service company. The manufacturer will not be responsible for any costs found necessary to correct problems
due to improper setup, improper installation, adjustments, improper operating procedure on the part of the user, etc.
Some specifi c examples of service calls which are not included in the limited warranty are:
• Correcting wiring problems in the electrical circuit supplying the equipment.
• Resetting circuit breakers or other switches.
• Adjusting or calibrating of thermostat.
Specifi cations & illustrations subject to change without notice or incurring obligations.
O' Fallon MO | Printed in U.S.A. (12/10)
¢708879m¤
708879B (Replaces 708879A)
Loading...