Remeha Fusion Heat Pump Brochure

PUMP OUT MAXIMUM EFFICIENCY AND MINIMUM EMISSIONS.
REMEHA
FUSION
Reducing your
2 3
INTRODUCTION
60% of the buildings that will be standing in 2050 are already here with us today. So tomorrow, there will be a great need for intelligent heating technology specifically designed for refurbished buildings. This is where Remeha’s advanced thinking is leading the way. To a future where our highly efficient heating systems help to improve the overall energy efficiency of refurbished buildings. Giving them new life and a more sustainable future.
THE REMEHA FUSION
Low Carbon heating with maximum efficiency.
Remeha has been at the forefront of gas boiler technology and innovation for decades, now we have an addition to the family, the Remeha Fusion which is a range of Low Carbon Gas Absorption
Heat Pumps (GAHP).
These heat pumps are a ready made low carbon solution for commercial, industrial and larger residential applications.
These heat pumps not only take energy from the surrounding air but also employs a highly efficient gas condensing heat generator to maintain high operational efficiencies.
Using gas as the primary energy source directly at the point of use, rather than electricity which is largely generated from the inefficient coal or gas fired power stations, the Remeha Fusion has a significantly smaller carbon footprint as a result.
The Remeha Fusion also cuts costs even further when you factor in the price of gas when compared with electricity, which is typically a third of the price.
The heat pump can provide up to 65% of additional heat by drawing in free energy from the surrounding air.
When you take into account both of these factors, the heat pump helps to provide reduced energy and carbon emissions when compared with conventional methods of providing heat to buildings.
Ammonia refrigerant which has a zero global warming potential (GWP) and ozone depletion (ODP) is used in the Remeha Fusion.
The Remeha Fusion is supplied either as a single stand alone unit or as a cascade system. These can be integrated with condensing boilers such as the Quinta Pro, Gas 210 Pro and the Gas 316/610 Pro.
REMEHA FUSION
OVERVIEW
REMEHA FUSION
OVERVIEW
Remeha Fusion range
There are two versions available:
Remeha Fusion HP35A LT (Low Temperature)
The LT version has been optimised to operate on low temperature circuits like under floor heating and has a maximum operating flow temperature of 55°C.
Remeha Fusion HP35A HT (High Temperature)
The HT version has been optimised to operate on higher temperature circuits and is suitable for production of hot water, this unit has a maximum flow temperature of 65°C.
Remeha Fusion Cascade Units
Cascade systems are available in either the LT or HT format, and these are supplied from 2 to 5 units on one skid mounted frame. These units can achieve outputs from 70 - 175kW. If you require higher outputs then you simply add multiple cascade units together to achieve the desired output.
In a cascade system the flow/return and gas pipework are supplied fully pre-assembled, so the installation time is reduced. Each individual unit is single phase as standard, however the cascade system requires a three phase supply to the electrical control panel.
The Fusion should be sized to achieve 4000 hours or greater and to take into account the base heating load. Buffer vessels are normally used as part of the system design.
All versions are for external use only. A low noise brushless fan is fitted which keeps the environmental noise down to a minimum. Anti vibration pads are available to reduce the transmission noises throughout the building.
All versions are suitable to be used in conjunction with existing Remeha products like the Quinta Pro, Gas 210 Pro and the Gas 310/610 Pro boiler range.
All versions are suitable for on/off, 0-10v and Open Therm modulating control systems, so integrating them with Remeha boilers makes it even simpler.
Further technical advice can be obtained from our Renewables technical department on 0118 978 3434.
4 5
T004108-A
T004107-A
ONE SYSTEM, MANY ADVANTAGES
Accessories
Vibration dampers for stand-alone heat
pumps aswell as cascade configurations
0-10V interface
CAN-OpenTherm interface
Trace heating for all cascade configurations
(2, 3, 4 and 5 GAS HP)
Remeha Fusion heat pumps can be used in:
Existing buildings, including base load optimisation
in installations with a medium to high heating capacity
Swimming pools, hotels, healthcare institutions
Industr y: for heating process
water and climatecontrol
Retail: individual stores as well as
larger shoppingcentres
Offices
Industrial construction
Apartment blocks
In general, the Remeha Fusion is very well-suited to applications in both existing and new buildings.
The Remeha Fusion is equipped with a two stage frost protection as standard with the circulating pump being switched on for the first stage and if necessary the burner is fired in conjunction with the circulating pump for the second stage frost protection, trace heating is also available as an optional extra. If for any reason that the gas or electrical supplies cannot be guaranteed during colder weather, then a water/ antifreeze mixture should be considered, further advice should be obtained from the Renewables technical department on 0118 978 3434.
REMEHA FUSION
OVERVIEW
THE MAIN FACTS
General
Available in a low temperature (LT) version
or a high temperature (HT)version
Outside air as source, so no costs for
connecting a source
Installed outside Easy to install, no unusual
modificationsrequired
No three-phase current required (with the
exception of fully assembled skids with multiple pumps)
Can be installed in combination with
existing units Can be used in new and existingbuildings Reduction of energy consumption Significant reduction of CO2 emissions Suitable for pre-heating domestic hot water Remeha maintenance service available 10-year warranty on the sealed part of the
heat pump
Unit
High efficiency up to 165% Output 35kW Modulating from 100%-50% Control via 0-10V, or on/off High efficiency even at low
outsidetemperatures Problem-free operation at extreme
outside temperatures Built-in control strategy to protect
againstfreezing Maintains efficiency at high
dischargetemperatures
Skids (cascade frames)
Fully pre-assembled cascade frames
(electrical, gas and condensation connections
already present) Cascade frames available in four versions,
varying in output from 70kW to 175kW Fitted with energy-efficient modulating pumps
for a constant deltaT Option of hydraulically isolating an individual
heat pump on a skid from the other heat
pumps (for example during repair/
maintenance) Equipped as standard with thermostat pockets
inside the insulation of the main pipes, allowing
a trace heating system to be fitted if required
(optional) As an option, the main flow and return pipes
can be fitted with a trace heating, which is
always advisable in the UK
Dimensions and connections
G Gas connection Ø 3/4" F I Water flow Ø 1 1/4" F O Water return Ø 1 1/4" F
Side viewFront view Connections
Main dimensions of cascade configuration (skid) with 2, 3, 4 and 5 heat pumps
380 380
731 4551 4551 137
1554
2314
T004286-A
4936
1554
152 4551 251
4551 4551 4551 137137
3610
1554
T004106-A
6490
REMEHA FUSION
OVERVIEW
1554
Loading...
+ 4 hidden pages