Regency S2400M, F2400M User Manual

Download

www.regency-ﬁ re.com

Freestanding Woodstove

Owners &

Installation Manual

Tested by:

918-154b

MODELS: F2400M S2400M

Installer: Please complete the details on the back cover

and leave this manual with the homeowner.

Homeowner: Please keep these instructions for future reference.

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4

02/18/08

Thank-you for purchasing a

REGENCY FIREPLACE PRODUCT.

The pride of workmanship that goes into each of our products will give you years of trouble-free enjoyment. Should you have any questions about your product that are not covered in this manual, please contact the REGENCY DEALER in your area.

Keep those REGENCY FIRES burning.

SAFETY NOTE: If this woodstove is not properly installed, a house ﬁ re may result. For your safety, follow the installation instructions, contact local building, ﬁ re ofﬁ cials, or authority having jurisdiction about restrictions and installation inspection requirements in your area.

The authority having jurisdiction should be consulted before installation to determine the need to obtain a permit.

Modular Parts

Regency Freestanding Woodstove

TABLE OF CONTENTS

SAFETY LABEL

Safety Label for F2400 ..................................................4

Safety Label for S2400 ..................................................5

INSTALLATION

Unit Dimensions ............................................................6

Residential Installation ..................................................7

Modular Installation Options ..........................................7

Room Air ....................................................................... 8

Important .......................................................................8

Minimum Clearance to Combustible Materials ..............8

Stove Assembly Prior to Installation ............................10

Step-by-Step Chimney and Connector Installation ..... 11

Masonry Chimney .......................................................12

Masonry Fireplace .......................................................12

Factory Built Chimney .................................................12

Combustible Wall Chimney

Connector Pass-Throughs ..........................................13

Recommended Heights For Woodstove Flue ..............14

Mobile Home Installation ............................................. 15

Listed Components For Mobile Home Installation .......16

Flue Bafﬂ e &Secondary Air Tube Installation .............. 16

Brick Installation ..........................................................17

Door Handle ................................................................17

Glass Installation ......................................................... 17

Step-by-Step Optional Accessories Installation ...........17

Screen Door ................................................................17

MAINTENANCE

Maintenance ................................................................21

Creosote ......................................................................21

Maintenance of Gold-plated Doors ..............................21

Latch Adjustment ......................................................... 21

Door Gasket ................................................................21

Glass Maintenance ......................................................21

Wood Storage ..............................................................21

PARTS LIST

F2400 Stove Main Assembly .......................................22

S2400 Step Stove Main Assembly .............................. 23

Pedestal, Bottom Shield & Leg Options ......................24

Firebrick .......................................................................25

WARRANTY

Warranty ......................................................................27

OPERATING INSTRUCTIONS

Operating Instructions .................................................19

Draft Control ................................................................ 19

First Fire ......................................................................19

Fan Operation .............................................................20

Ash Disposal ...............................................................20

Safety Guidelines and Warnings ................................. 20

Regency Freestanding Woodstove

SAFETY LABEL

This is a copy of the label that accompanies each Regency Freestanding Woodstove (F2400M). We have printed a copy of the contents here for your review.

LISTED SPACE HEATER, SOLID FUEL TYPE, ALSO SUITABLE FOR MOBILE HOME INSTALLATION

MODEL: REGENCY MEDIUM FREESTANDING STOVE - F2400M

TESTED TO: UL-1482 / ULC-S627-00 / UL-737 REPORT NO:219-S-02-2

THE F2400M MEETS UL737 STANDARD FOR FIREPLACE STOVES WHEN A FIRESCREEN IS PROVIDED.

F2400M WITH

AIRMATE SHIELD

F2400M WITH AIRMATE SHIELD F2400M WITHOUT AIRMATE SHIELD

MEASURE FLUE FROM HEATER CENTER-LINE

RESIDENTIAL INSTALLATION USING

SIDEWALL A 406 mm / 16 in D 711 mm / 28 in BACKWALL B 280 mm / 11 in E 444 mm / 17.5 in CORNER C 152 mm / 6 in F 444 mm / 17.5 in

INSTALLATION USING LISTED DOUBLE WALL

SIDEWALL A 380 mm / 15 in D 685 mm / 27 in BACKWALL B 140 mm / 5.5 in E 304 mm / 12 in CORNER C 102 mm / 4 in F 393 mm / 15.5 in

INSTALLATION USING LISTED DOUBLE WALL

CONNECTOR - RESIDENTIAL CLOSE CLEARANCE SIDEWALL A 380 mm / 15 in D 685 mm / 27 in BACKWALL B 140 mm / 5.5 in E 304 mm / 12 in CORNER C 102 mm / 4 in F 393 mm / 15.5 in

INSTALLATION USING LISTED DOUBLE WALL

SIDEWALL G 380 mm / 15 in I 685 mm / 27 in BACKWALL H 140 mm / 5.5in J 304 mm / 12 in

MINIMUM ALCOVE CEILING HEIGHT: 2.15 M / 7 FT MAXIMUM ALCOVE DEPTH 915 MM / 36 IN. MINIMUM CLEARANCES FOR HORIZONTAL CONNECTOR TO CEILING: 455 MM / 18" THE SPACE BENEATH THE HEATER MUST NOT BE OBSTRUCTED. OPERATE ONLY WITH FIREBRICKS IN PLACE.

FOR USE WITH SOLID WOOD FUEL ONLY. USE OF OTHER FUELS MAY DAMAGE HEATER AND CREATE A HAZARDOUS CONDITION. DO NOT OBSTRUCT COMBUSTION AIR OPENINGS. OPERATE ONLY WITH FIREBRICKS IN PLACE. RISK OF SMOKE AND FLAME SPILLAGE, OPERATE ONLY WITH DOORS FULLY OPEN OR FULLY CLOSED. IF INSTALLED IN A MOBILE HOME OPERATE ONLY WITH DOORS FULLY CLOSED - OPEN FEED DOOR TO FEED FIRE ONLY. WHEN OPERATED WITH DOORS OPEN THE MANUFACTURER SUPPLIED SCREEN MUST BE USED. DO NOT USE GRATE OR ELEVATE FIRE. BUILD WOOD FIRE DIRECTLY ON HEARTH. DO NOT OVERFIRE - IF HEATER OR CHIMNEY CONNECTOR GLOWS YOU ARE OVERFIRING. INSPECT AND CLEAN CHIMNEY AND CONNECTOR FREQUENTLY. UNDER CERTAIN CONDITIONS OF USE CREOSOTE BUILDUP MAY OCCUR RAPIDLY. KEEP FURNISHINGS AND OTHER COMBUSTIBLE MATERIAL AWAY FROM HEATER. REPLACE GLASS ONLY WITH NEOCERAM GLASS. COMBUSTIBLE FLOOR MUST BE PROTECTED BY NON-COMBUSTIBLE MATERIAL EXTENDING BENEATH THE HEATER AND TO THE FRONT AND SIDES AS INDICATED OR TO THE NEAREST PERMITTED COMBUSTIBLE MATERIAL. OPTIONAL COMPONENT: FAN (846-515), ELECTRICAL RATING: VOLTS 115, 60 HZ, 2 AMPS, SCREEN DOOR (846-101) DANGER: RISK OF ELECTRIC SHOCK. DISCONNECT POWER BEFORE SERVICING UNIT. DO NOT ROUTE POWER CORD UNDER OR IN FRONT OF APPLIANCE. COMPONENTS REQUIRED FOR MOBILE HOME INSTALLATION: OUTSIDE AIR KIT AND ONE OF THE FOLLOWING DOUBLE WALL CONNECTOR IN CANADA: LISTED SECURITY MODEL DP, OR OLIVER MACLEOD PRO-VENT PV DOUBLE WALLED CONNECTOR WITH LISTED CHIMNEY SYSTEM: SECURITY MODEL S2100, ICC EXCEL 2100, SELKIRK SENTINAL CF. IN USA: LISTED DOUBLE WALL CONNECTORS SECURITY MODEL DP, SELKIRK MODEL DS, OLIVER MACLEOD PRO VENT PV, SIMPSON DURA VENT MODEL DVL, GSW SUPER PIPE 6, METAL-FAB DOUBLE WALL. CONNECTED TO ONE OF THE FOLLOWING COMPATIBLE CHIMNEY SYSTEMS SECURITY MODEL S2100 OR MODEL ASHT, SELKIRK MODEL SSII, OLIVER MACLEOD PRO JET 3103, SIMPSON DURA PLUS, GSW MODEL SC OR METAL-FAB TEMP/GUARD, AMERI-TEC HS, ICC EXCEL 2100 . USE CHIMNEY COMPONENTS AS SPECIFIED IN INSTALLATION INSTRUCTIONS.

F2400M WITHOUT AIRMATE SHIELD

MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS

SINGLE WALL CONNECTOR

CONNECTOR - MOBILE HOME

CONNECTOR - ALCOVE

NOTE: Regency units are constantly being

improved. Check the label on the unit and if there is a difference, the label on the unit is the correct one.

SAFETY LABEL FOR F2400M

244

DO NOT REMOVE THIS LABEL

244

INSTALL AND USE ONLY IN ACCORDANCE WITH THE MANUFACTURER'S INSTALLATION AND OPERATING INSTRUCTIONS. CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTION IN YOUR AREA. USE 150 MM (6 IN.) DIAMETER MINIMUM 24 MSG BLACK OR 26 MSG BLUED STEEL CONNECTOR WITH LISTED UL103 HT FACTORY-BUILT CHIMNEY SUITABLE FOR USE WITH SOLID FUELS OR MASONRY CHIMNEY. SEE LOCAL BUILDING CODE AND MANUFACTURER'S INSTRUCTIONS FOR PRECAUTIONS REQUIRED FOR PASSING A CHIMNEY THROUGH A COMBUSTIBLE WALL OR CEILING. DO NOT PASS CHIMNEY CONNECTOR THROUGH COMBUSTIBLE WALL OR CEILING. DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.

MEASURE FLUE FROM HEATER CENTER-LINE

RESIDENTIAL INSTALLATION USING

SIDEWALL A 457 mm / 18 in D 762 mm / 30 in BACKWALL B 305 mm / 12 in E 470 mm / 18.5 in CORNER C 165 mm / 6.5 in F 457 mm / 18 in

SIDEWALL A 380 mm / 15 in D 685 mm / 27 in BACKWALL B 165 mm / 6.5 in E 330 mm / 13 in CORNER C 152 mm / 6 in F 444 mm / 17.5in

SIDEWALL A 380 mm / 15 in D 685 mm / 27 in BACKWALL B 165 mm / 6.5in E 330 mm / 13 in CORNER C 152 mm / 6 in F 444 mm / 17.5 in

SIDEWALL G 380 mm / 15 in I 685 mm / 27 in BACKWALL H 165 mm / 6.5 in J 330 mm / 13 in

SINGLE WALL CONNECTOR

INSTALLATION USING LISTED DOUBLE WALL

CONNECTOR - MOBILE HOME

INSTALLATION USING LISTED DOUBLE WALL

CONNECTOR - RESIDENTIAL CLOSE CLEARANCE

INSTALLATION USING LISTED DOUBLE WALL

CONNECTOR - ALCOVE

FLOOR

PROTECTION*

K 405 mm / 16 in L 150 mm / 6 in M 150 mm / 6 in

* In Canada, ﬂ oor protection must

extend 18" (450mm) to the front and 8" (200mm) to each side and back of the stove.

JAN FEB MAR APR MAY JUN JUL AUG SEPT OCT NOV DEC

MANUFACTURED BY: FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 VENTURE ST.

UNITED STATES ENVIRONMENTAL

PROTECTION AGENCY

DELTA, BC V4G 1H4

CERTIFIED TO COMPLY WITH JULY 1990

PARTICULATE EMISSION STANDARDS.

MADE IN CANADA

CAUTION

HOT WHILE IN OPERATION DO NOT TOUCH. KEEP CHILDREN,

CLOTHING AND FURNITURE AWAY. CONTACT MAY CAUSE

SKIN BURNS. READ NAMEPLATE AND INSTRUCTIONS.

918-172c

Regency Freestanding Woodstove

DATE OF MANUFACTURE

2007 20092008

SAFETY LABEL

This is a copy of the label that accompanies each Regency Medium Freestanding Step Stove (S2400M). We have printed a copy of the contents here for your review.

SAFETY LABEL FOR S2400M

LISTED SPACE HEATER, SOLID FUEL TYPE, ALSO SUITABLE FOR MOBILE HOME INSTALLATION

MODEL: REGENCY MEDIUM FREESTANDING STEP STOVE - S2400M TESTED TO: UL-1482 / ULC-S627-00 / UL 737 REPORT NO: 219-S-02-2

THE S2400M MEETS UL737 STANDARD FOR FIREPLACE STOVES WHEN A FIRESCREEN IS PROVIDED.

S2400M

MEASURE FLUE FROM HEATER CENTER-LINE

SIDEWALL A 406 mm / 16 in D 711 mm / 28 in BACKWALL B 280 mm / 11 in E 444 mm / 17.5 in CORNER C 152 mm / 6 in F 444 mm / 17.5 in

INSTALLATION USING LISTED DOUBLE WALL

SIDEWALL A 380 mm / 15 in D 685 mm / 27 in BACKWALL B 140 mm / 5.5 in E 304 mm / 12 in CORNER C 102 mm / 4 in F 393 mm / 15.5 in

INSTALLATION USING LISTED DOUBLE WALL

CONNECTOR - RESIDENTIAL CLOSE CLEARANCE

SIDEWALL A 380 mm / 15 in D 685 mm / 27 in BACKWALL B 140 mm / 5.5 in E 304 mm / 12 in CORNER C 102 mm / 4 in F 393 mm / 15.5 in

INSTALLATION USING LISTED DOUBLE WALL

SIDEWALL G 380 mm / 15 in I 685 mm / 27 in BACKWALL H 140 mm / 5.5in J 304 mm / 12 in

IF INSTALLED IN A MOBILE HOME OPERATE ONLY WITH DOORS FULLY CLOSED - OPEN FEED DOOR TO FEED FIRE ONLY. WHEN OPERATED WITH DOORS OPEN THE MANUFACTURER SUPPLIED SCREEN MUST BE USED. DO NOT USE GRATE OR ELEVATE FIRE. BUILD WOOD FIRE DIRECTLY ON HEARTH. DO NOT OVERFIRE - IF HEATER OR CHIMNEY CONNECTOR GLOWS YOU ARE OVERFIRING. INSPECT AND CLEAN CHIMNEY AND CONNECTOR FREQUENTLY. UNDER CERTAIN CONDITIONS OF USE CREOSOTE BUILDUP MAY OCCUR RAPIDLY. KEEP FURNISHINGS AND OTHER COMBUSTIBLE MATERIAL AWAY FROM HEATER. REPLACE GLASS ONLY WITH NEOCERAM GLASS. COMBUSTIBLE FLOOR MUST BE PROTECTED BY NON-COMBUSTIBLE MATERIAL EXTENDING BENEATH THE HEATER AND TO THE FRONT AND SIDES AS INDICATED OR TO THE NEAREST PERMITTED COMBUSTIBLE MATERIAL.

OPTIONAL COMPONENT: FAN (846-515), ELECTRICAL RATING: VOLTS 115, 60 HZ, 2 AMPS, SCREEN DOOR (846-101) DANGER: RISK OF ELECTRIC SHOCK. DISCONNECT POWER BEFORE SERVICING UNIT. DO NOT ROUTE POWER CORD UNDER OR IN FRONT OF APPLIANCE. COMPONENTS REQUIRED FOR MOBILE HOME INSTALLATION: OUTSIDE AIR KIT AND ONE OF THE FOLLOWING DOUBLE WALL CONNECTOR IN CANADA: LISTED SECURITY MODEL DP, OR OLIVER MACLEOD PRO-VENT PV DOUBLE WALLED CONNECTOR WITH LISTED CHIMNEY SYSTEM: SECURITY MODEL

S2100, ICC EXCEL 2100, SELKIRK SENTINAL CF. IN USA: LISTED DOUBLE WALL CONNECTORS SECURITY MODEL DP, SELKIRK MODEL DS, OLIVER MACLEOD PRO VENT PV, SIMPSON DURA VENT MODEL DVL, GSW

SUPER PIPE 6, METAL-FAB DOUBLE WALL. CONNECTED TO ONE OF THE FOLLOWING COMPATIBLE CHIMNEY SYSTEMS SECURITY MODEL S2100 OR MODEL ASHT, SELKIRK MODEL SSII, OLIVER MACLEOD PRO JET 3103, SIMPSON DURA PLUS, GSW MODEL SC OR METAL-FAB TEMP/GUARD, AMERI-TEC HS, ICC EXCEL 2100 . USE CHIMNEY COMPONENTS AS SPECIFIED IN INSTALLATION INSTRUCTIONS.

UNITED STATES ENVIRONMENTAL

PROTECTION AGENCY

WALL OR CEILING. DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.

S2400M MINIMUM CLEARANCES

TO COMBUSTIBLE MATERIALS

RESIDENTIAL INSTALLATION USING

SINGLE WALL CONNECTOR

CONNECTOR - MOBILE HOME

CONNECTOR - ALCOVE

NOTE: Regency units are constantly being

improved. Check the label on the unit and if there is a difference, the label on the unit is the correct one.

245

DO NOT REMOVE THIS LABEL

245

FLOOR

PROTECTION*

K 405 mm / 16 in L 150 mm / 6 in M 150 mm / 6 in

*In Canada, ﬂ oor protection must extend

18" (450mm) to the front and 8" (200mm) to each side and back of the stove.

MANUFACTURED BY: FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 VENTURE ST. DELTA, BC V4G 1H4

CERTIFIED TO COMPLY WITH JULY 1990 PARTICULATE EMISSION STANDARDS.

JAN FEB MAR APR MAY JUN JUL AUG SEPT OCT NOV DEC

MADE IN CANADA

Regency Freestanding Woodstove

CAUTION

HOT WHILE IN OPERATION DO NOT TOUCH. KEEP CHILDREN,

CLOTHING AND FURNITURE AWAY. CONTACT MAY CAUSE

SKIN BURNS. READ NAMEPLATE AND INSTRUCTIONS.

918-203c

DATE OF MANUFACTURE

2007 20092008

INSTALLATION

UNIT DIMENSIONS

27-3/8” (695mm)

24-7/8” (632mm)

6-5/8”

(168mm)

(772mm)

30-3/8"

24” (610mm)

(740mm)

29-1/8"

Regency Freestanding Woodstove

INSTALLATION

RESIDENTIAL

INSTALLATION

1) Please read this entire manual before you

install and use your new woodstove. Failure to follow instructions may result in property damage, bodily injury or even death. Be aware that local Codes and Regulations may override some items in this manual. Check with your local inspector.

2) Select a position for your Regency Stove.

Consult the minimum clearance chart for your model and set the stove in place. For close clearance installation use listed double wall connector systems.

3) To insure vertical alignment, suspend a

plumb bob from the ceiling over the exact center of your stove ﬂ ue and mark a spot on the ceiling to indicate the center of the chimney.

4) Check that the area above the ceiling is

clear for cutting. Re-conﬁ rm the clearance from the stove to combustibles to insure that they are within the prescribed limits.

5) This woodstove must be connected to a

UL 103 HT (ULC S629) listed chimney or a code approved masonry chimney with a ﬂ ue liner.

6) Install chimney according to chimney manu-

facturers instructions. The performance of your woodstove is governed to a very large part by the chimney system. Too short a chimney can cause difﬁ cult start-up, dirty glass, back smoking when door is open, and

even reduced heat output. Too tall a chimney may prompt excessive draft which can result in very short burn times and excessive heat output. The use of an inexpensive ﬂ ue pipe damper may be helpful in reducing excessive draft.

CAUTION: The chimney should be the same

size as the 6" ﬂ ue outlet on the stove. The chimney must be listed as suitable for use with solid fuels. For other types of chimneys check with your local building code ofﬁ cials. Do not confuse a chimney with a type “B” Venting System used for gas appliances as suitable for a wood burning appliance. For Mobile Home installations refer to that section within this manual.

7) Mark the location of the pedestal base or legs

on the ﬂ oor, then move the stove aside and mark the position of the ﬂ oor protector.

8) The ﬂ oor protector must be of non-combus-

tible material and must extend 16" (406mm) in front of the door opening and 6" (152mm) to the sides and rear of the unit. Some areas may require a larger size ﬂ oor protector. See your local inspector. For outside air installation refer to Mobile Home installation instructions within this manual.

NOTE: In Canada, ﬂ oor protection must

extend 18" (450mm) to the front and 8" (200mm) to each side and back of the stove.

9) When the ﬂ oor protection is complete, posi-

tion the stove with the ﬂ ue collar centered under the installed chimney.

10) In seismically active areas, Regency rec-

ommends that your unit is secured to the ﬂ oor by using the bolt down holes inside the pedestal (the same ones used in Mobile Home installations).

11) For residential installations using 6" "C"

Vent (single wall) the chimney connector must be at least 24 gauge steel. Do not use galvanized pipe. For Mobile Home installation refer to the Mobile Home installation instructions within this manual.

12) Do not connect this unit to a chimney serving another appliance.

13) A chimney connector cannot pass through

an attic or roof space, closet or similar concealed space, or a ﬂ oor, ceiling, wall or partition of combustible construction. In Canada, if passage through a wall, or partition of combustible construction is desired, the installation shall conform to CAN/CSA-B365, Installation Code for SolidFuel-Burning Appliances and Equipment.

14) Your Regency Woodstove is not to be connected to any air distribution duct.

Emissions from burning wood or gas could contain chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

The following items are required when assembling your Regency Stove. F2400M unit - the Rear Heat Deﬂ ector is supplied with the stove, but if

MODULAR INSTALLATION OPTIONS

you choose not to use it you must use the Airmate instead.

Modular Part

Clearances are different. See the Minimum Clearance to Combustible Materials chart in the Installation section of this

F2400M

Airmate OR

Rear Heat Deﬂ ector

F2400M, S2400M

Pedestal OR

Legs

manual. Generally you can get closer clearances with the airmate than with the rear heat deﬂ ector.

Convection heat with Airmate vs. Radiant Heat with Rear Heat Deﬂ ector. The airmate pushes heat forward and into the room, the rear heat deﬂ ector deﬂ ects the heat upward. Refer to the Installation section within this manual.

There are no performance differences with either the pedestal or legs. It is primarily a personal preference. Legs can be either painted steel, painted cast, or gold plated cast.

Leg installation requires the bottom shield (refer to Leg and Bottom Shield Assembly, Installation section).

OPTIONS: These can be installed at time of installation or added later:

Modular Option

Blower/Fan

Ash Drawer Kit

Screen Door

Regency Freestanding Woodstove

Adding the blower will increase the area heated by the stove, it can move warm air beyond the room where the stove is installed (refer to Blower/Fan, Installation section).

Adding the Ash Drawer Kit makes cleaning ashes out of the stove easier and cleaner (refer to Bottom Shield Ash Drawer Kit, Installation section).

A simple add-on option that will allow you to enjoy the sound, warmth and view of an open ﬁ re.

Things to consider when choosing options:

Things to consider when choosing options

INSTALLATION

ROOM AIR

IMPORTANT

For installation using room air for combustion, remove knockout from the pedestal, and/or from the bottom if using a heat shield.

Mobile home installations require the use of outside air.

On pedestal units there are two locations where outside air may be adapted to the unit. If using the bottom of the pedestal, do not remove knockout from the rear of the pedestal. Only remove rear knockout if outside air will be brought in from the rear.

On leg units outside air can only be brought in from the bottom of the heat shield.

Note: Once the knockout is removed there

are two tabs remaining. Bend both tabs out for ease of installation when attaching outside air.

MINIMUM CLEARANCE TO

COMBUSTIBLE MATERIALS

Please read the section below carefully as clearances depend on whether the airmate or the rear heat deﬂ ector is installed on the stove.

Measurements "From Unit" are from the top plate of the stove to a side wall or to a corner, and from the rear heat shield to a back wall.

Clearances may only be reduced by means approved by the regulatory authority.

NOTE: Be aware that local Codes and Regulations may override some clearances listed in this manual.

Check with your local inspector.

Residential Installation “C” Vent (Single Wall)

Unit From Unit From Corner From Flue Center-Line

A B C D E F

Medium F2400M with Airmate 16" (406 mm) 11" (279 mm) 6" (152 mm) 28" (710 mm) 17.5" (444 mm) 17.5" (444 mm) with Rear Deﬂ ector 18" (457 mm) 12" (304 mm) 6.5" (165 mm) 30" (762 mm) 18.5" (469 mm) 19.5" (495 mm)

Medium S2400M Step Stove 16" (406 mm) 11" (279 mm) 6" (152 mm) 28" (710 mm) 17.5" (444 mm) 17.5" (444 mm)

Residential Close Clearance (To be installed with required pipe components)

When the stove is installed as a close clearance residential unit, a listed double wall connector is required from the stove collar to the ceiling level.

Unit From Unit From Corner From Flue Center-Line

A B C D E F

Medium F2400M with Airmate 15" (381 mm) 5.5" (139 mm) 4" (101 mm) 27" (685 mm) 12" (304 mm) 15.5" (393 mm) with Rear Deﬂ ector 15" (381 mm) 6.5" (165 mm) 6" (152 mm) 27" (685 mm) 13" (330 mm) 17.5" (444 mm)

Medium S2400M Step Stove 15" (381 mm) 5.5" (139 mm) 4" (101 mm) 27" (685 mm) 12" (304 mm) 15.5" (393 mm)

Mobile Home Close Clearance (To be installed with required pipe components)

"C" Vent single wall pipe is not approved for Mobile Home installations. (Refer to Mobile Home Instructions.)

Unit From Unit From Corner From Flue Center-Line

A B C D E F

Medium S2400M Step Stove 15" (381 mm) 5.5" (139 mm) 4" (101 mm) 27" (685 mm) 12" (304 mm) 15.5" (393 mm)

Regency Freestanding Woodstove

INSTALLATION

Minimum Alcove Clearance to Combustible Materials

The Regency Freestanding models have been alcove approved and must be installed with a listed double wall connector to the ceiling level.

Note: Minimum alcove ceiling height - 84" Maximum depth of alcove - 36"

From From Flue Min. Min.Hearth

Unit Unit Center-line Width to Rear Wall

G H I J K L

Medium F2400M with Airmate 15" (381 mm) 5.5" (139 mm) 27" (685 mm) 12" (304 mm) 54" (1371 mm) 48" (1219 mm) with Rear Deﬂ ector 15" (381 mm) 6.5" (165 mm) 27" (685 mm) 13" (330 mm) 54" (1371 mm) 49" (1244 mm)

Medium S2400M Step Stove 15" (381 mm) 5.5" (139 mm) 27" (685 mm) 12" (304 mm) 54" (1371 mm) 48" (1219 mm)

Floor Protection

A combustible ﬂ oor must be protected by non-combustible material (like tile, concrete board, or certiﬁ ed to UL-1618 or as deﬁ ned by local codes) extending beneath the heater and a minimum of 6" (152mm) from each side and minimum 16" (406mm) from the front face of the stove and minimum 6" (or the rear clearance to combustibles whichever is smaller) from the rear of the stove.

When installed with horizontal venting, non-combustible ﬂ oor protection must beneath the ﬂ ue pipe and extend 2" (51mm) beyond each side.

Minimum Overall Width (X) of Floor Protector for all installations:

Stove F2400M 36" (914 mm)

Step Stove S2400M 36" (914 mm)

Minimum Overall Depth (Y) of Floor Protector

Residential Residential Mobile Home Alcove Unit "C" Vent Close Clearance Close Clearance

Y Z Y Z Y Z Y Z Medium F2400M with Airmate 46" (1168 mm) 6" (152 mm) 45"* (1143 mm) 5" (127 mm) 45" (1143 mm) 5" (127 mm) 45"* (1143) 5" (127 mm) with Rear Deﬂ ector 46" (1168 mm) 6" (152 mm) 45" (1143 mm) 5" (127 mm) 45" (1143 mm) 5" (127 mm) 45" (1143) 5" (127 mm)

Medium S2400M 46" (1168 mm) 6" (152 mm) 45"* (1143 mm) 5" (127 mm) 45" (1143 mm) 5" (127 mm) 45"* (1143) 5" (127 mm)

- Step Stove

NOTE: In Canada, ﬂ oor protection must extend 18" (450mm) to the

front and 8" (200mm) to each side and back of the stove.

*The rear clearance to combustibles is less than 6" (, for corner installations the rear corners may be angled to take advantage of the closer clearances.

Regency Freestanding Woodstove

INSTALLATION

STOVE ASSEMBLY

PRIOR TO

INSTALLATION

All units require either the pedestal or 4 legs attached to the base. The F2400M stove requires either the Airmate or Rear Heat Deﬂ ector on top of the stove. Clearances to combustible materials vary depending on whether the airmate or rear heat deﬂ ector is installed, so be sure to check the Minimum Clearances, Installation section.

Airmate Assembly for F2400M

(850-105)

1) The airmate sits on top of the stove with

the slots in the sides ﬁ tting over the curved deﬂ ector on the rear stove top. See diagram

1. Discard the Rear Heat Deﬂ ector that is supplied with the unit, it is not required if the airmate is installed.

2) Center the airmate and push it forward to the

front of the stove. The back of the airmate should be level with the back and sides of the rear heat shield. See Diagrams 2 & 3.

Rear Heat Deﬂ ector

Assembly for F2400M

(815-555)

The rear heat deﬂ ector is supplied with the stove and must be installed unless the optional airmate has been selected. It stops the heat radiated from the ﬂ ue collar from overheating the rear wall. The rear heat deﬂ ector is installed on top of the rear heat shield, as shown in Diagram 4.

Pedestal Assembly

F2400M & S2400M

(020-915)

1) For easier assembly, tip the stove on its

back (onto a soft surface to prevent scratching).

Hint: If you have chosen the Ash Drawer

option, remove the ash dump cover plates before attaching the pedestal. See page 17 "Ashdrawer Kit Installation".

2) Remove the blanking plate if a) you are not installing outside combustion

air or

b) outside air is to be brought in from the

rear of the stove.

3) Unscrew the 4 bolts in the under-side of the

stove. Align the holes in the corners of the pedestal top with the corresponding holes in the base of the stove. Fasten using a bolt and washer for each corner.

Diagram 1

Diagram 2

Diagram 4

S2400M Side Shield Adjustment

The left and right side shields are lowered for shipping and handling. It allows for a handhold on the top of the stove. Before placing in the Step Stove in its ﬁ nal position, the side shields must be raised.

Loosen the screws on the rear on the stove (3 per side), slide the side panel up as far as possible and then secure by tightening the screws.

4) Push the

Regency logo into the two holes in the front bottom left corner of the pedestal cover plate.

Note: Any paint touch up should be done

prior to placing logo on pedestal.

Diagram 3

5) If not using ash drawer, then cover plate must

be installed. If using ash drawer, then disregard cover plate.

Regency Freestanding Woodstove

INSTALLATION

Leg and Bottom Shield Assembly

F2400M & S2400M

Bottom Shield 020-911

Legs (set of 4) Steel - Painted Black 850-125 Cast - Painted Black 850-126 Cast - Gold Plated 850-127

The instructions below apply to the steel leg, painted cast leg and the gold plated cast leg. It will be easier to attach the legs to the stove if the stove is tipped on its back (preferably on a soft surface to prevent scratching). Ensure to be extremely careful when tipping stove.

1) Remove the 4 bolts from underside of the

base of the pedestal and discard. Also remove cover plate and put to the side.

2) Line up the heat shield with the bottom of

the unit.

3) Start threading the bolt and washer (supplied

with the bottom shield) for about 1/4 of the way through the leg with the washers being underneath the legs. Ensure that the legs are properly aligned with heat shield and tighten the bolts.

4) Level the stove by adjusting the levelling

bolts in the bottom of each leg.

STEP-BY-STEP

CHIMNEY AND

CONNECTOR

INSTALLATION

Note: These are a generic set of chimney in-

stallation instructions. Always follow the manufacturers own instructions explicitly. Verify the Minimum Recommended Heights for Woodstove Flue (Table 1 in the Installation section).

1) With your location already established, cut

and frame the roof hole. It is recommended that no ceiling support member be cut for chimney and support box installation. If it is necessary to cut them, the members must be made structurally sound.

2) Install radiant shield and support from

above.

3) Stack the insulated pipe onto your ﬁ nish

support to a minimum height of 3 feet above the roof penetration, or 2 feet above any point within 10 feet measured horizontally. There must be at least 3 feet of chimney above the roof level.

8) To complete your chimney installation, install

the double wall connector pipe from the stove’s ﬂ ue collar to the chimney support device.

9) If you are using a horizontal connector,

the chimney connector should be as high as possible while still maintaining the 18" (457mm) minimum distance from the horizontal connector to the ceiling.

10) NOTE: Residential Close Clearance and Alcove installations require a listed double wall connector from the stove collar to the ceiling level.

The diagrams below illustrate one way to install your unit into a standard ceiling or with a horizontal connector. Check with your dealer or installer for information on other options available to you.

5) Reinstall cover plate.

6) Install logo plate onto heat shield by placing

in 2 holes as shown in diagram.

If you are installing outside combustion air, bend the tabs out 90 degrees. Pipe fresh air into the bottom shield by using a minimum 4" duct pipe with a mesh grill at the outside termination. Attach the pipe to the 2 tabs with screws.

Regency Freestanding Woodstove

Note: Increasing the chimney height above

this minimum level will sometimes help your unit to “breathe” better by allowing a greater draft to be created. This greater draft can decrease problems such as, difﬁ cult start-ups, back-smoking when door is open, and dirty glass. It might be sufﬁ cient to initially try with the minimum required height, and then if problems do arise add additional height at a later date.

4) Slide the roof ﬂ ashing over your chimney

and seal the ﬂ ashing to the roof with rooﬁ ng compound. Secure the ﬂ ashing to your roof with nails or screws.

5) Place the storm collar over the ﬂ ashing,

sealing the joints with a silicone caulking.

6) Fasten the raincap with spark screens (if

required) to the top of your chimney.

7) For optimum efﬁ ciency when installing into

a masonry chimney, size accordingly, i.e. the 6" (152mm) ﬂ ue dia. is 28.28 sq.in.

Standard Ceiling Installation

Horizontal Installation

INSTALLATION

MASONRY

CHIMNEY

Ensure that a masonry chimney meets the minimum standards of the National Fire Protection Association (NFPA) by having it inspected by a professional. Make sure there are no cracks, loose mortar or other signs of deterioration and blockage. Have the chimney cleaned before the stove is installed and operated. When connecting the stove through a combustible wall to a masonry chimney, special methods are needed.

MASONRY

FIREPLACE

There are listed kits available to connect a stove to a masonry ﬁ replace. The kit is an adapter that is installed at the location of the ﬁ replace damper. The existing damper may have to be removed to allow installation.

FACTORY

BUILT CHIMNEY

When a metal prefabricated chimney is used, the manufacturer's installation instructions must be followed. You must also purchase and install the ceiling support package or wall pass-through and "T" section package, ﬁ restops (where needed), insulation shield, roof ﬂ ashing, chimney cap, etc. Maintain proper clearance to the structure as recommended by the manufacturer. The chimney must be the required height above the roof or other obstructions for safety and proper draft operation.

Regency Freestanding Woodstove

COMBUSTIBLE WALL CHIMNEY

CONNECTOR PASS-THROUGHS

INSTALLATION

Method A: 12" (304.8 mm) Clearance to Combustible Wall

Member:

Using a minimum thickness 3.5" (89 mm) brick and a 5/8" (15.9 mm) minimum wall thickness clay liner, construct a wall pass-through. The clay liner must conform to ASTM C315 (Standard Speciﬁ cation for Clay Fire Linings) or its equivalent. Keep a minimum of 12" (304.8 mm) of brick masonry between the clay liner and wall combustibles. The clay liner shall run from the brick masonry outer surface to the inner surface of the chimney ﬂ ue liner but not past the inner surface.

Firmly grout or cement the clay liner in place to the chimney ﬂ ue liner.

Method B: 9" (228.6 mm) Clearance to Combustible Wall Member:

Using a 6" (152.4 mm) inside diameter, listed, factory-built Solid-Pak chimney section with insulation of 1" (25.4 mm) or more, build a wall pass-through with a minimum 9" (228.6 mm) air space between the outer wall of the chimney length and wall combustibles. Use sheet metal supports fastened securely to wall surfaces on all sides, to maintain the 9" (228.6 mm) air space. When fastening supports to chimney length, do not penetrate the chimney liner (the inside wall of the Solid-Pak chimney). The inner end of the Solid-Pak chimney section shall be ﬂ ush with the inside of the masonry chimney ﬂ ue, and sealed with a non-water soluble refractory cement. Use this cement to also seal to the brick masonry penetration.

Minimum 12 in. (304.8mm) to combustibles

Minimum chimney clearance to brick and combustibles 2 in. (50.8mm)

Minimum clearance 12 in. (304.8mm) of brick

Chimney

Chimney Flue

Masonry chimney

connector

Fire clay liner

Method C: 6" (152.4 mm) Clearance to Combustible Wall Member:

Starting with a minimum 24 gage (.024" [.61 mm]) 6" (152.4 mm) metal chimney connector, and a minimum 24 gage ventilated wall thimble which has two air channels of 1" (25.4 mm) each, construct a wall pass-through. There shall be a minimum 6" (152.4) mm separation area containing ﬁ berglass insulation, from the outer surface of the wall thimble to wall combustibles. Support the wall thimble, and cover its opening with a 24-gage minimum sheet metal support. Maintain the 6" (152.4 mm) space. There should also be a support sized to ﬁ t and hold the metal chimney connector. See that the supports are fastened securely to wall surfaces on all sides. Make sure fasteners used to secure the metal chimney connector do not penetrate chimney ﬂ ue liner.

Method D: 2" (50.8 mm) Clearance to Combustible Wall Member:

Start with a solid-pak listed factory built chimney section at least 12" (304 mm) long, with insulation of 1" (25.4 mm) or more, and an inside diameter of 8" (2 inches [51 mm] larger than the 6" [152.4 mm] chimney connector). Use this as a pass-through for a minimum 24-gage single wall steel chimney connector. Keep solid-pak section concentric with and spaced 1" (25.4 mm) off the chimney connector by way of sheet metal support plates at both ends of chimney section. Cover opening with and support chimney section on both sides with 24 gage minimum sheet metal supports. See that the supports are fastened securely to wall surfaces on all sides. Make sure fasteners used to secure chimney ﬂ ue liner.

Regency Freestanding Woodstove

INSTALLATION

RECOMMENDED HEIGHTS FOR

WOODSTOVE FLUE

Simple rules on draft (refer to Table 1).

1) At sea level minimum height is 12'

straight.

2) Add the following vertical height to compen-

sate for: 45 deg. elbow = 1 ft. 90 deg. elbow = 2 ft. "T" = 3 ft. Each foot of horizontal run = 2 ft.

TABLE 1

MINIMUM RECOMMENDED FLUE HEIGHTS IN FEET

# OF ELBOWS

ELEVATION (FT) ABOVE SEA LEVEL 0 2 x 15o 4 x 15o 2 x 30o 4 x 30o 2 x 45o 4 x 45

0-1000 12.0 13.0 14.0 15.0 18.0 16.0 20.0 1000-2000 12.5 13.5 14.5 15.5 19.0 16.5 21.0 2000-3000 13.0 14.0 15.0 16.0 19.5 17.0 21.5 3000-4000 13.5 14.5 15.5 17.0 20.0 18.0 22.5 4000-5000 14.0 15.0 16.0 17.5 21.0 18.5 23.0 5000-6000 14.5 15.5 17.0 18.0 21.5 19.0 24.0 6000-7000 15.0 16.0 17.5 18.5 22.5 20.0 25.0 7000-8000 15.5 16.5 18.0 19.0 23.0 20.5 25.5 8000-9000 16.0 17.0 18.5 20.0 24.0 21.0 26.5 9000-10000 16.5 17.5 19.0 20.5 24.5 22.0 27.0

3) Add 4% overall for each 1000' above sea

level.

Example: a)

1-1/2 ft. of horizontal run = 3 ft. one "T" = 3 ft. Total Addition (at sea level) = 6 ft.

Example: b) One 90 deg. elbow = 2 ft. 2 ft. of horizontal run = 4 ft. one "T" = 3 ft. Total Addition (at sea level) = 9 ft.

(Measured from the top of the unit)

Recommended Flue Height

Elevation Example a) Example b) 0' 18' 21' 1000' 18.72' 21.84' 2000' 19.44' 22.68' 5000' 21.60' 25.20' 8000' 23.76' 27.72'

NOTE: No more than two offsets (four elbows) allowed. Two 45o elbows equal one 90o elbow.

Regency Freestanding Woodstove

MOBILE HOME INSTALLATION

INSTALLATION

Once you have properly marked the position of your unit and the ﬂ oor protection as outlined in the Residential Installation items #1 through #8, a supply of fresh air has to be supplied to your unit. Cut a minimum 4" (102mm) diameter hole through your ﬂ oor protector and the ﬂ oor directly under your pedestal base to the outside. Use 4" (102mm) duct pipe with a mesh grill to pipe fresh air into the pedestal area. Block off the hole in the back of the pedestal with the square plate and the two 1/2" screws provided.

Place your unit in position and secure it to the ﬂ oor using two lag bolts 3/8" (10mm) x 3-1/2" (89mm) through the two holes inside the pedestal base. It is important to maintain the structural integrity of the Mobile Home ﬂ oor, walls and roof when installing your unit.

For Mobile Home units installed in the U.S. the unit must be grounded using a #8 ground wire with approved termination and star washer.

CAUTION: At no time use unlabelled

parts, or substitute parts made for another

chimney system.

Install as per chimney manufacturer's

installation instructions.

WARNING: Operate only with door fully closed - open feed door to feed ﬁ re only.

In addition to standard installation instructions the following requirements are mandatory for installation in a mobile home.

1) The stove must be permanently bolted to the ﬂ oor of the Mobile Home using the ﬂ oor screws provided.

2) The stove must have a permanent outside air source for combustion.

3) The stove must be electrically grounded to the steel chassis of the Mobile Home.

4) A listed double-wall connector chimney system, roof thimble, spark arrestor and roof ﬂ ashing kit suitable for use in Mobile Homes must be used.

5) If the chimney exits the Mobile Home at a location other than through the roof, and exits at a point 7ft. (2130mm) or less above the ground level on which the Mobile Home is positioned a guard or method of enclosing the chimney shall be ﬁ tted at the point of exit for a height up to 7ft. (2130mm).

6) The chimney shall be attached directly to the room heater and shall extend at least 3 ft. (914mm) above the part of the roof through which it passes. The top of the chimney should project at least 2ft. (610mm) above the highest elevation of any part of the Mobile Home within 10 ft. (3048mm) of the chimney.

7) The chimney system shall comply with Local Requirements.

Regency Freestanding Woodstove

8) Any openings in a chimney guard where required must not permit the entrance of 3/4" (19mm) diameter rod.

9) CAUTION: THE STRUCTURAL INTEGRITY OF THE MOBILE HOME ROOF, FLOOR, WALLS AND CEILING MUST BE MAINTAINED.

10) Check any other local building code as other

local codes may apply.

11) WARNING: DO NOT INSTALL IN A SLEEP- ING ROOM OF A MOBILE HOME.

12) Use silicone to create an effective vapour

barrier at the location where the chimney or other component penetrates to the exterior of the structure.

INSTALLATION

LISTED COMPONENTS

FOR MOBILE HOME

INSTALLATION

The Regency F2400M and S2400M Freestanding pedestal units are approved for installation in a Mobile Home if one of the following pipe systems is used.

U.S. Installation*

METALBESTOS SSII Qty. Part # Description

1 6DS-VK Connector Kit 1 6TMH Shield/Support 1 6TAF-6 Flashing 1 6T-36 Chimney Length 1 6T-18 Chimney Length 1 6T-CT Rain Cap

PRO-JET 3103 Qty.Part # Description

1 PV06-TK Connector 1 CSB Shield/Support 1 RRS Radiation Shield 1 LFR03 Flashing 1 SL3 Chimney Length 1 SL1 Chimney Length 1 RCSA Rain Cap

SIMPSON DURA-PLUS Qty.Part # Description

1 6DVL8693 Connector Kit 1 6DP-MH9096 Mobile Home Kit

ICC EXCEL 2100 Qty.Part # Description

1 6CL48 48" Chimney length (also in 12", 18", 24" lengths. 1 6RC Rain Cap 1 6RCS Spark Screen (for rain cap) 1 6RDS/SQS Round/Square support box 1 6VF Flashing 1 6UBA "Ultrablack" Close Clearance Connector

Canadian Installations*

SECURITY S2100 (see above for details)

ICC EXCEL 2100 (see above for details)

SELKIRK SENTINAL CF

*The use of alternate pitch ﬂ ashings, support box extensions, additional chimney lengths, and additional chimney bracing, may be used on each of the previously listed systems. These parts though must be from the same system as listed, and must be a similar and/or complimentary part.

Slide the tube into the left hand side, as far as possible and then bring it back into the hole on the right hand side until it locks into position. If the tube will not slide in easily, simply use a pair of vise grips or pliers and tap it into place with a hammer. A tighter ﬁ t will ensure the tube will not move when the unit is burning.

2) Slide the left bafﬂ e over the air tubes from

the front and then push it to the back.

Side View

3) Tilt the left bafﬂ e up on top of the side chan-

nel and it will leave enough room to position the right bafﬂ e in the same manner as Step

1) above. Then reposition the left bafﬂ e ﬂ at on the air tubes.

SECURITY ASHT Qty.Part # Description

1 DL42A-6 Connector Kit 1 6SS Shield/Support 1 6FAMH Flashing 1 6L3 Chimney Length 1 6L1 Chimney Length 1 CPE Rain Cap

SECURITY S2100 Qty.Part # Description

1 DL42A-6 Connector Kit 1 6XSF Support 1 6XFA Flashing 1 6XL3 Chimney Length 1 6XL18 Chimney Length 1 6XCPE Rain Cap

METAL-FAB TEMP/GUARD 2100 Qty.Part # Description

1 6DWBK Connector 1 6TGRS Roof Support 1 6TGG36 Chimney Length 1 6TGG12 Chimney Length 1 6TGF Flashing 1 6TGC Rain Cap

AMERI-TEC HS Qty.Part # Description

1 6DCC Connector 1 6HSRS-12 Roof Support (6PLRS-12-BK) 1 6F Flashing 1 6HS-36 Chimney Length 1 6HS-18 Chimney Length 1 6HS-RCS Rain Cap (6PL-MPC)

CAUTION: At no time use unlabelled parts, or substitute parts made for another chimney system.

Install as per chimney manufacturer's installation instructions.

FLUE BAFFLE &

SECONDARY AIR TUBE

INSTALLATION

The ﬂ ue bafﬂ e system located in the upper area of the ﬁ rebox is removable to make cleaning your chimney system easier. The bafﬂ es must be installed prior to your ﬁ rst ﬁ re. Smoke

spillage and draft problems may occur if the bafﬂ es are improperly positioned. Check

the position of the bafﬂ es on a regular basis as they can be dislodged if too much fuel is forced into the ﬁ rebox.

Freestanding Stove

F2400M

The unit arrives with the 2 bafﬂ es on the ﬂ oor of the ﬁ rebox.

1) If all 4 air tubes are installed continue on to

Step 2), if not, follow the instructions below. Install the air tube into the holes in the side channels. The notch goes on the right hand side with the air holes facing toward the door.

Front View

4) Important: push both bafﬂ es so they are tight against the side walls.

Front View

Note: When getting the chimney cleaned,

push the bafﬂ es forward toward the front of the stove, this should leave sufﬁ cient access to the ﬂ ue. If it is not enough space then remove the middle air tube (reverse the procedure in step 1) above), and bafﬂ e and then replace everything when cleaning is completed.

Regency Freestanding Woodstove

INSTALLATION

BRICK INSTALLATION

Firebrick is included to extend the life of your stove and radiate heat more evenly. Check to see that all ﬁ rebricks are in their correct positions and have not become misaligned during shipping.

The "AD" brick in the drawings below is the brick covering the Ash Dump hole that is used when the Ash Drawer Kit is installed.

DOOR HANDLE

Attach spring handle by rotating counter clockwise onto rod. Ensure that the rod ﬁ ts into the entire length of the spring handle (refer to the Diagram below).

STEP-BY-STEP

OPTIONAL

ACCESSORIES

INSTALLATION

The pieces listed below can be purchased and installed during the initial installation or added on later.

Pedestal Ash Drawer Kit (850-100)

1) Remove the bricks from the ﬂ oor of the

ﬁ rebox.

2) If using ashdrawer, discard cover plate.

3) Remove the ash dump cover plates (one

inside the ﬁ rebox and one on the underside of the ﬁ rebox) by removing the two nuts and bolts holding the 2 plates together from inside the ﬁ rebox.

4) Push the ash plug into the hole inside the

ﬁ rebox and replace all the bricks except for the brick over the ash plug (refer to the brick diagram in the Brick Installation section).

5) Place the ash drawer lid inside the pedestal,

and the ash plug tool beside the lid, then slide the ash drawer inside so it sits on top of the lid.

4) Push the ash plug into the hole inside the

ﬁ rebox and replace all the bricks except for the brick over the ash plug (see brick diagram in the Brick Installation section).

5) Place the ash plug tool beside the lid, then

slide the ash drawer inside.

Refer to Ash Drawer Operating Guidelines in the Operating Instructions section.

SCREEN DOOR

Hook screen to the inside on the right side of the ﬁ rebox door opening. Lock in place by turning handle.

GLASS INSTALLATION

Remove the door from the stove and remove the glass retainer. Position the glass in the door, make sure that the glass gasketing will properly seal your unit, and replace the retainer, it should rest on the gasket not the glass. Tighten securely, but do not wrench down on the glass as this may cause the glass to break.

Refer to the Ash Drawer Operating Guidelines in the Operating Instructions section.

Bottom Shield Ash Drawer Kit

(850-101 )

1) Remove the bricks from the ﬂ oor of the

ﬁ rebox.

2) Remove and discard the cover plate by

removing the two screws on the front of the Bottom Shield.

3) Remove the ash dump cover plates (one

inside the ﬁ rebox and one on the underside of the ﬁ rebox) by removing the two nuts and bolts holding the 2 plates together from inside the ﬁ rebox.

Hooks

Back Side of Screen Shown

NOTE: The handle must be positioned at 10 o'clock when closed to avoid the handle from getting hot and to ensure the screen stays in place.

Handle at 10 o'clock position.

Handle Lock

Regency Freestanding Woodstove

INSTALLATION

Blower/Fan (846-515)

1) Remove the two screws from the top of the

fan housing.

2) Slide the fan up into the rear heat shield.

3) After aligning holes, secure the fan to the rear

heat shield using the two screws removed earlier.

CAUTION: The connection cord should not

be in contact with any hot surfaces. Do not route cord under or in front of unit.

Read the Fan Operation instructions before using.

Neutral

120V AC

60 Hz

Fan Thermodisc

(normally open)

Live

Ground

Green

Black Black

Manual/

Auto

Switch

Fan

Switch

White

Low (Red)

High (Black)

Black

Blower/Fan Wiring Diagram

WARNING: Electrical Grounding Instructions This appliance is equipped with a three pronged (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding prong from this plug.

Fan Fan

Ground

CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation.

Regency Freestanding Woodstove

OPERATING INSTRUCTIONS

OPERATING

INSTRUCTIONS

With your unit now correctly installed and safety inspected by your local authority, you are now ready to start a ﬁ re. Before establishing your ﬁ rst ﬁ re, it is important that you fully understand the operation of your draft control.

WARNING Fireplace Stoves equipped with doors should be operated only with doors fully open or doors fully closed. If doors are left partly open, gas and ﬂ ame may be drawn out of the ﬁ replace stove opening, creating risks from both ﬁ re and smoke.

When operated with doors open the manufacturer supplied screen must be used.

DRAFT CONTROL

Both the primary and air wash drafts are controlled by the control rod located on the left side of the unit (when facing the unit). To increase your draft - pull open, and to decrease - push closed. All units have a secondary draft system that continually allows combustion air to the induction ports at the top of the ﬁ rebox, just below the ﬂ ue bafﬂ e.

Important: If you are using room air for combustion, make sure that the back cover plate at the rear of the pedestal is not installed. The cover plate must be installed on the unit if your stove is located in a mobile home or if using outside air from the bottom.

Pull - Open Push - Closed

WARNING: To build a ﬁ re in ignorance or to disregard the information contained in this section can cause serious permanent damage to the unit and void your warranty!!

FIRST FIRE

When your installation is completed and inspected you are ready for your ﬁ rst ﬁ re.

1) Open control fully.

2) Open ﬁ rebox door and build a small ﬁ re us-

ing paper and dry kindling on the ﬁ rebrick hearth. Secure door on the ﬁ rebox and wait a few minutes for a good updraft in the ﬂ ue to establish the ﬁ re. (Leaving the door slightly open will help your ﬁ re start more rapidly.)

CAUTION: Never leave unit

unattended if door is left open. This procedure is for ﬁ re start-up only, as unit may overheat if door is left open for too long.

3) With the draft still in the fully open position

add two or three seasoned logs to your ﬁ re. Form a trench in the ash bed to allow air to reach the rear of the ﬁ rebox prior to closing the door.

4) After about 45 minutes, when your wood

has begun to burn strongly, adjust your draft control down to keep the ﬁ re at a moderate level.

WARNING: Never build a roaring ﬁ re

in a cold stove. Always warm your stove up slowly!

5) Once a bed of coals has been established

on the ﬁ rebrick hearth, you may adjust the draft control to a low setting to operate the unit at its most efﬁ cient mode.

6) During the ﬁ rst few ﬁ res, keep the combus-

tion rate at a moderate level and avoid a large ﬁ re. Only after 5 or 6 such ﬁ res can you operate the stove at its maximum setting, and only after the metal has been warmed.

7) For the ﬁ rst few days, the stove will give off an

odour from the paint. This is to be expected as the high temperature paint becomes seasoned. Windows and/or doors should be left open to provide adequate ventilation while this temporary condition exists. Burning the stove at a very high temperature the ﬁ rst few times may damage the paint. Burn ﬁ res at a moderate level the ﬁ rst few days.

8) Do not place anything on the stove top dur-

ing the curing process. This may result in damage to your paint ﬁ nish.

9) During the ﬁ rst few days it may be more

difﬁ cult to start the ﬁ re. As you dry out your ﬁ rebrick and your masonry ﬂ ue, your draft will increase.

10) For those units installed at higher elevations

or into sub-standard masonry ﬁ replaces, drafting problems may occur. Consult an experienced dealer or mason on methods of increasing your draft.

11) Some cracking and popping noises may be

experienced during the heating up process. These noises will be minimal when your unit reaches temperature.

12) Before opening your door to reload, open

draft fully for approximately 10 to 15 seconds until ﬁ re has been re-established. This will minimize any smoking.

13) All fuel burning appliances consume oxygen

during operation. It is important that you supply a source of fresh air to your unit while burning. A slightly opened window is sufﬁ cient for the purpose. If you also have a ﬁ replace in your home, a downdraft may be created by your Regency Stove causing a draft down your chimney. If this occurs, slightly open a window near your unit.

CAUTION: If the body of your unit, ﬂ ue bafﬂ e or any part of the chimney connector starts to glow, you are over ﬁ ring. Stop loading fuel immediately and close the draft control until the glow has completely subsided.

14) Green or wet wood is not recommended for

your unit. If you must add wet or green fuel, open the draft control fully until all moisture has been dispersed by the intense ﬁ re. Once all moisture has been removed, the draft control may be adjusted to maintain the ﬁ re.

15) If you have been burning your stove on a low

draft, use caution when opening the door. After opening the damper, open the door a crack, and allow the ﬁ re to adjust before fully opening the door.

16) The controls of your unit or the air supply

passages should not be altered to increase ﬁ ring for any reason.

17) If you burn the unit too slowly or at too low

a setting your unit will not be operating as efﬁ ciently as it can. An easy rule of thumb says that if your glass is clean, then your ﬂ ue is clean and your exhaust is clean. Burn the stove hot enough to keep your glass clean and you won't need to clean your ﬂ ue as often.

Regency Freestanding Woodstove

OPERATING INSTRUCTIONS

FAN OPERATION

Automatic

To operate the fan automatically, push the bottom switch on the side of the fan housing to "AUTO" and the top switch to either "HIGH" or "LOW" for fan speed.

This will allow the fan to turn on as the stove has come up to operating temperature. It will also shut the fan system off after the ﬁ re has gone out and the unit cooled to below a useful heat output range.

Manual

To manually operate the fan system push the bottom switch to "MAN" and the top switch to either "HIGH" or "LOW". This will bypass the sensing device and allow full control of the fan.

Switching from "AUTO" to "MAN" or "HIGH" to "LOW" may be done anytime.

ASH DISPOSAL

During constant use, ashes should be removed every few days. The Ash Drawer option features a convenient ash dump for easy removal of ash, refer to Modular Installation Options section.

Safety Precautions

1) Do not allow ashes to build up to the loading

doors! Only remove ashes when the ﬁ re has died down. Even then, expect to ﬁ nd a few hot embers.

2) Please take care to prevent the build-up of

ash around the start-up air housing located inside the stove box, under the loading door lip.

3) Never start a ﬁ re if the ash plug and ash

drawer are not in place. This will cause over ﬁ ring which can cause excessive warping of the stove. Evidence of over ﬁ ring can void the warranty on your stove.

4) The ﬁ rebricks are brittle and can be damaged

if the plug is replaced carelessly or pieces that are too large are forced through the hole.

Ash Drawer Operating Guideline

1) Only clean ashes out of the stove when the

unit has cooled down. Remove the plug by lifting on the handle using the tool provided. The plug may still be warm, use caution.

Push the ashes down the hole into the ash drawer, the large pieces can be left in the ﬁ rebox and burned during the next ﬁ re or removed through the door opening.

2) Always leave 1/2 to 1 inch of ash in the

bottom of the ﬁ rebox. This helps in easier starting and a more uniform burn of your ﬁ re. Replace ash plug when ashes have been removed.

3) Pedestal Units: To remove the drawer, lift slightly and slide

it out. When the drawer is completely out, slide the cover plate over the ash drawer and carry away.

Bottom Shield (with Legs) Units: To remove the drawer, lift slightly and slide

it out, and carry it away.

4) When emptying the ash drawer, make sure

the ashes are cold. Ashes should be placed in a metal container with a tight ﬁ tting lid. The closed container of ashes should be placed on a non-combustible ﬂ oor or on the ground, well away from all combustible materials, pending ﬁ nal disposal. If the ashes are disposed of by burial in soil or otherwise locally dispersed, they should be retained in the closed container until all cinders have thoroughly cooled. Other waste should not be placed in the ash container.

5) Before putting the ash drawer back into

place, make sure the ash plug is back in place.

Pedestal Units: make sure the cover lid is

off.

SAFETY GUIDELINES

AND WARNINGS

1) Never use gasoline, gasoline type lantern

fuels, kerosene, charcoal lighter fuel, or similar liquids to start or ‘freshen up’ a ﬁ re in your heater. Keep all such liquids well away from the heater while it is in use.

2) Keep the door closed during operation and

maintain all seals in good condition.

4) If you have smoke detectors, prevent smoke

spillage as this may set off a false alarm.

5) Do not overﬁ re heater. If the chimney con-

nector, ﬂ ue bafﬂ e or the stove top begin to glow, you are over ﬁ ring. Stop adding fuel and close the draft control. Over ﬁ ring can cause extensive damage to your stove including warpage and premature steel corrosion. Over ﬁ ring will void your warranty.

6) Do not permit creosote or soot build-up

in the chimney system. Check and clean chimney at regular intervals. Failure to do so can result in a serious chimney ﬁ re.

7) Your Regency stove can be very hot. You

may be seriously burned if you touch the stove while it is operating, keep children, clothing and furniture away. Warn children of the burn hazard.

8) The stove consumes air while operating,

provide adequate ventilation with an air duct or open a window while the stove is in use.

9) Do not connect this unit to a chimney ﬂ ue

serving another appliance.

10) Do not use grates or andirons or other

methods for supporting fuel. Burn directly on the bricks.

11) Open the draft control fully for 10 to 15

seconds prior to slowly opening the door when refuelling the ﬁ re.

12) Do not connect your unit to any air distribu-

tion duct.

13) Your woodstove should burn dry, standard

ﬁ rewood only. The use of cut lumber, plywood, “mill ends”, etc. is not allowed as this fuel can easily overheat your woodstove. Evidence of excessive overheating will void your warranty. As well, a large portion of sawmill waste is chemically treated lumber, which is illegal to burn in many areas. Salt drift wood and chemically treated ﬁ re logs also must not be burned in your woodstoves.

14) Do not store any fuel closer than 2 feet

from your unit. Do not place wood, paper, furniture, drapes or other combustibles near the appliance.

15) WARNING: Do not operate without either the Ash Plug properly seated or the Ash Dump Plates screwed in place, excessive temperatures will result.

16) Do not operate with broken glazing.

3) Do not burn any quantities of paper, gar-

bage, and never burn ﬂ ammable ﬂ uids such as gasoline, naptha or engine oil in your stove.

Regency Freestanding Woodstove

MAINTENANCE

It is very important to carefully maintain your ﬁ replace stove, including burning seasoned wood and maintaining a clean stove and chimney system. Have the chimney cleaned before the burning season and as necessary during the season, as creosote deposits may build up rapidly. Moving parts of your stove require no lubrication.

CREOSOTE

When wood is burned slowly, it produces tar and other organic vapours, which when combined with moisture, form creosote. The creosote vapours condense in the relatively cool chimney ﬂ ue of a slow burning ﬁ re. As a result, creosote residue accumulates on the ﬂ ue lining. When ignited, this creosote can result in an extremely hot ﬁ re.

WARNING: Things to remember in case of a chimney ﬁ re:

1. Close all draft and damper controls.

2. CALL THE FIRE DEPARTMENT.

Ways to Prevent and Keep Unit

Free of Creosote

1) Burn stove with the draft control wide open

for about 10-15 minutes every morning during burning season.

2) Burn stove with draft control wide open

for about 10 - 15 minutes every time you apply fresh wood. This allows the wood to achieve the charcoal stage faster and burns up any unburned gas vapours which might otherwise be deposited within the system.

5) The chimney and chimney connector should

be inspected at least once every two months during the heating season to determine is a creosote buildup has occured.

6) Have chimney system and unit cleaned by competent chimney sweeps twice a year during the ﬁ rst year of use and at least once a year thereafter or when a signiﬁ cant layer of creosote has accumulated (3 mm/1/8" or more) it should be removed to reduce the risk of a chimney ﬁ re.

MAINTENANCE OF

GOLD-PLATED DOORS

The gold electroplated ﬁ nish on the door requires little maintenance, and need only be cleaned with a damp cloth. DO NOT use abrasive materials or chemical cleaners, as they may harm the ﬁ nish and void the warranty.

GLASS MAINTENANCE

Your Regency stove is supplied with 5 mm Neoceram ceramic glass (Part #846-302) that will withstand the highest heat that your unit will produce. In the event that you break your glass by impact, purchase your replacement from an authorized Regency dealer only, and follow our step-by-step instructions for replacement (refer to Glass Installation section).

Allow the stove to cool down before cleaning the glass, do not clean the glass when it is hot. Do not use abrasive cleaners.

LATCH ADJUSTMENT

The door latch may require adjustment as the door gasket material compresses after a few ﬁ res. Removal of the spacer washer, shown in the diagram below, will allow the latch to be moved closer to the door frame, causing a tighter seal. Remove and replace the nuts, washer and spacer as shown.

DOOR GASKET

If the door gasket requires replacement 7/8" diameter material must be used. Regency uses AMATEX # 10-863KR 7/8" dia. gasket (Part #846-570). A proper high temperature gasket adhesive is required. See your Regency Dealer.

WOOD STORAGE

Store wood under cover, such as in a shed, or covered with a tarp, plastic, tar paper, sheets of scrap plywood, etc., as uncovered wood can absorb water from rain or snow, delaying the seasoning process.

3) Only burn seasoned wood! Avoid burning

wet or green wood. Seasoned wood has been dried at least one year.

4) A small hot ﬁ re is preferable to a large

smouldering one that can deposit creosote within the system.

Regency Freestanding Woodstove

PARTS LIST

F2400M STOVE MAIN ASSEMBLY

Part# Description

1) 846-913 Door Assy-Med Gold F2400M (no glass) 846-915 Door Assy-Med Black F2400M (no glass)

3) 846-302 Glass - Replacement - F2400M

4) 936-243 7/8" Adhesive Tape Gasket

5) 820-184 Glass Retainer Clips (8/set)

6) * Screw - 1/4 - 20 x 3/8"

7) 948-170/P Small Glass Retainer F2400M

9) 846-973 Door Handle Assembly

12) 820-375 Ash Hole Cover Plate

13) * Bolt 1/4 - 20 x 1/2 Hex Head

14) 820-376 Retainer Plate - Ash Dump - Top

15) * Nut - 1/4 - 20 Hex

16) 846-570 7/8" Door Gasket Repair Kit

17) 846-918 Hinge Cap - Gold (2/set)

19) 948-101 Spring Handle - Large

20) 948-102 Spring Handle - Small

Part# Description

846-515 Complete Fan/Blower Assy (120 V)

25) 910-684 Power Cord (120 V)

27) 910-142 Thermodisc - Fan Auto ON/OFF

28) 910-138 Manual/Auto Switch (2-way)

29) 910-140 Fan Speed Switch HI/OFF/LOW (3-way)

30) 910-157/P Fan/Blower Motor (120 V)

36) 033-953 Air Tube - 3/4" F2400M (Qty: 4)

37) 020-957 Bafﬂ e (set) F2400M

40) 815-557 Rear Air Deﬂ ector

41) 850-105 Airmate - Medium

42) 846-101 Screen Door

918-154b Manual

*Not available as a replacement part.

Regency Freestanding Woodstove

S2400M STEP STOVE MAIN ASSEMBLY

PARTS LIST

Part# Description

1) 846-913 Door Assy- Medium Gold S2400M (no glass) 846-915 Door Assy-Medium Black S2400M (no glass)

3) 846-302 Glass - Replacement - S2400M

4) 936-243 7/8" Adhesive Tape Gasket

5) 846-920 Glass Retainer Clips (8/set)

6) * Screw - 1/4 - 20 x 3/8"

7) 948-170/P Small Glass Retainer - S2400M

9) 846-973 Door Handle Assembly

16) 846-570 7/8" Door Gasket Repair Kit

17) 846-918 Hinge Caps - Gold (2/set)

19) 948-101 Spring Handle - Large

20) 948-102 Spring Handle - Small

Part# Description

846-515 Complete Fan/Blower Assy (120 V)

25) 910-684 Power Cord (120 V)

27) 910-142 Thermodisc Fan Auto ON/OFF

28) 910-138 Manual/Auto Switch (2-way)

29) 910-140 Fan Speed Switch HI/OFF/LOW (3-way)

30) 910-157/P Fan/Blower Motor (120 V)

36) 033-953 Air Tube - 3/4" S2400M (Qty: 4)

37) 020-957 Bafﬂ e (set) S2400M

42) 846-101 Screen Door

918-154b Manual

*Not available as a replacement part.

Regency Freestanding Woodstove

PARTS LIST

PEDESTAL, BOTTOM SHIELD & LEG OPTIONS

Part# Description

48) 020-915 Pedestal - Medium

49) 904-257 Large Magnet Catch

50) * Blanking Plate - Pedestal

850-100 Ashdrawer Kit - Pedestal

45) * Ashdrawer - Pedestal

46) * Ashdrawer Lid Assy

58) 942-110 Ash Plug

59) 820-249 Ash Plug Tool Handle

56) 020-911 Bottom Shield - Medium

57) * Blanking Plate - Btm Shield

850-101 Ashdrawer Kit - Btm Shield

55) * Ashdrawer - Bottom Shield

58) 942-110 Ash Plug

59) 820-249 Ash Plug Tool Handle

140) 850-126 Legs - Cast Black 850-127 Legs - Cast Gold 850-128 Legs - Cast Brush Nickel

142) 850-125 Legs - Steel Black

948-216 Logo - Regency 918-154b Manual

*Not available as a replacement part.

Regency Freestanding Woodstove

FIREBRICK

Part# Description

70) 902-111 Brick - Regular Full Size: 1-1/4" x 4-1/2" x 9"

74) 802-147 Brick Partial: 1-1/4" x 4-1/2" x 3-1/2"

75) 802-122 Brick Partial: 1-1/4" x 4-1/2" x 2"

76) 802-152 Brick Partial: 1-1/4" x 2" x 9"

PARTS LIST

Regency Freestanding Woodstove

NOTES

Regency Freestanding Woodstove

WARRANTY

Regency Fireplace Products are designed with reliability and simplicity in mind. In addition, our internal Quality Assurance Team carefully inspects each unit thoroughly before it leaves our door. FPI Fireplace Products International Ltd. is pleased to extend this limited lifetime warranty to the original purchaser of a Regency Product. This warranty is not transferable.

The Warranty: Lifetime

Covered under the agreement are the following components:

Firebox, ceramic bafﬂ e, vermiculite bafﬂ e, steel bafﬂ es (H2100), convector airmate, castings, ashdrawer, glass (thermal breakage), gold plating (against defective manufacture), airtubes (against warpage) and door handles.

The above will be covered for parts and subsidized labour for the ﬁ rst ﬁ ve years and parts only thereafter with the exception of the ﬁ reboxes (see below).

FPI is not liable for freight or labor on any wood burning appliance replaced in ﬁ eld.

Electrical components such as blowers, switches and thermodisc's are covered for two years parts and one year subsidized labour* from date of purchase.

Repair/replacement parts purchased by the consumer from FPI after the original coverage has expired on the unit will carry a 90 day warranty, valid with a receipt only. Any item shown to be defective will be repaired or replaced at our discretion. No labor coverage is included with these parts.

Conditions:

Any part or parts of this unit which in our judgement show evidence of such defects will be repaired or replaced at FPI's option, through an accredited distributor or agent provided that the defective part be returned to the distributor or agent Transportation Prepaid, if requested.

It is the general practice of FPI to charge for larger, higher priced replacement parts and issue credit once the replaced component has been returned to FPI and evaluated for manufacturer defect.

The authorized selling dealer is responsible for all in-ﬁ eld service work carried out on your Regency product. FPI will not be liable for results or costs of workmanship from unauthorized service persons or dealers.

At all times FPI reserves the right to inspect product in the ﬁ eld which is claimed to be defective.

All claims must be submitted to FPI by authorized selling dealers. It is essential that all submitted claims provide all of the necessary information including customer name, purchase date, serial #, type of unit, problem, and part or parts requested, without this information the warranty will be invalid.

Exclusions:

This limited Lifetime Warranty does not extend to or include paint, door or glass gasketing, ﬁ rebrick or trim. It does not cover installation and operational related problems such as over-ﬁ ring, use of corrosive driftwood, downdrafts or spillage caused by environmental conditions, nearby trees, buildings, hilltops, mountains, inadequate venting or ventilation, excessive offsets, negative air pressures caused by mechanical systems such as furnaces, fans, clothes dryers etc.

At no time will FPI be liable for any consequential damages which exceed the purchase price of the unit. FPI has no obligation to enhance or modify any unit once manufactured. ie. as products evolve, ﬁ eld modiﬁ cations or upgrades will not be performed.

FPI will not be liable for travel costs for service work.

Installation and environmental problems are not the responsibility of the manufacturer and therefore are not covered under the terms of this warranty policy.

Any unit which shows signs of neglect or misuse is not covered under the terms of this warranty policy.

The warranty will not extend to any part which has been tampered with or altered in any way, or in our judgment has been subject to misuse.

Freight damage to stoves and replacement parts is not covered by warranty and is subject to a claim against the freight carrier by the dealer.

FPI will not be liable for acts of God, or acts of terrorism, which cause malfunction of the appliance.

Performance problems due to operator error will not be covered by this warranty policy.

Products made or provided by other manufacturers and used in conjunction with the operation of this appliance without prior authorization from FPI, may nullify your warranty on this product.

* Subsidy according to job scale as predetermined by FPI.

Regency Freestanding Woodstove

Regency ﬁ replace products are designed

with reliability and simplicity in mind. In

addition, our internal Quality Assurance

Team carefully inspects each unit

thoroughly before it leaves our

door.

Fireplace Products International

Ltd. is pleased to extend this Limited

Lifetime Warranty to the original

purchaser of a Regency Product.

See the inside back cover for details.

http://www.regency-ﬁ re.com

Installer: Please complete the following information

Dealer Name & Address: ______________________________________________

___________________________________________________________________

Installer: ___________________________________________________________

Phone #: ___________________________________________________________

Date Installed: ______________________________________________________

Serial No.: __________________________________________________________

Regency and Classic are trademarks of FPI Fireplace Products International Ltd.

Printed in Canada

Regency S2400M, F2400M User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual