Regency E21-NG2, E21-LP2 User Manual

www.regency-ﬁ re.com

E21 Gas Insert

Owners &

Installation Manual

MODELS: E21-NG2 Natural Gas E21-LP2 Propane

WARNING: If the information in these instructions are not followed exactly, a ﬁ re or explosion may result causing property damage, personal injury or loss of life.

FOR YOUR SAFETY Do not store or use gasoline or other ﬂ ammable vapors and liquids in the vicinity of this or any other appliance.

Installation and service must be performed by a qualiﬁ ed installer, service agency or the gas supplier.

Tested by:

918-510

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4

Installer: Please complete the details on the back cover

and leave this manual with the homeowner.

Homeowner: Please keep these instructions for future reference.

FOR YOUR SAFETY What to do if you smell gas:

Do not try to light any appliance Do not touch any electrical switch:

do not use any phone in your building.

Immediately call your gas supplier

from a neighbour's phone. Follow the gas supplier's instructions.

If you cannot reach your gas

supplier, call the ﬁ re department.

02/01/07

CONGRATULATIONS!

You are the owner of a state-of-the-art Gas Insert by:

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD.

The Regency® Gas Fireplace Series has been designed to provide you with all the warmth and charm

of a ﬁ replace, at the ﬂ ick of a switch. The models E21-NG2 and E21-LP2 of this series have been approved by Warnock Hersey for safety. As it also bears our own mark, it promises to provide you with economy, comfort and security for many trouble free years to follow. Please take a moment now to acquaint yourself with these instructions and the many features of your Regency® Fireplace.

2 Regency® E21-2 Gas Fireplace Insert

E21 GAS INSERT

TABLE OF CONTENTS

SAFETY LABEL

Serial No. Decal ...........................................................4

REQUIREMENTS

MA Code - CO Detector

(for state of Massachusetts only) ..................................5

INSTALLATION

Important Message ......................................................6

Before You Start ............................................................6

General Safety Information ...........................................6

Policy for Solid Fuel Burning &

Factory Built Fireplaces ................................................. 7

Installation Checklist ......................................................7

Minimum Fireplace Clearances ..................................... 7

Clearances to Combustibles .........................................8

Gas Connection .............................................................9

High Elevation ...............................................................9

Wiring Diagrams .......................................................... 10

Flue Connector Installation ......................................... 11

Gas Pipe Pressure Testing ..........................................12

Offset Flue Adaptor ......................................................12

Venting ........................................................................12

Combustion and Ventilation Air ...................................12

Valve Description .........................................................13

Test for Flue Spillage ...................................................13

Optional Brick Panel ....................................................13

Gas Insert Aerationsystem .........................................13

Log Set Installation ......................................................14

Faceplate & Trim Installation ....................................... 14

Flush Glass ................................................................15

Flush Louvers ..............................................................16

Optional Bay Front ......................................................16

Bay Louvers ................................................................16

Conversion Kit# 534-969 from NG to LP ..................... 17

Full Screen doors ........................................................20

Remote Control ...........................................................22

Wall Switch ..................................................................22

Wall Thermostat .........................................................22

OPERATING INSTRUCTIONS

Final Check .................................................................23

Operating Instructions ................................................23

Lighting Procedure ......................................................23

Shutdown Procedure ...................................................23

First Fire ......................................................................23

Copy of Lighting Plate Instructions .............................24

Automatic Convection Fan Operation .........................25

Normal Operating Sounds of Gas Appliances .............25

MAINTENANCE

Maintenance Instructions ............................................25

Log Replacement ........................................................25

Glass Gasket ...............................................................25

Gold-plated Accessories ..............................................25

Removing Valve Assembly ..........................................26

Removing the Fan .......................................................26

Door Glass Replacement ............................................26

PARTS LIST

Main Assembly ............................................................27

Burner Assembly & Log Set ........................................28

Bay & Flush Front Assembly .......................................29

Faceplate Assembly ....................................................30

WARRANTY

Warranty .....................................................................31

3Regency® E21-2 Gas Fireplace Insert

SAFETY LABEL

This is a copy of the label that accompanies each Regency® Gas Insert. We have printed a copy of the contents here for your review. The safety label is located on the front inside base of the unit visible when the bottom louver is open.

Note: Regency® units are constantly being

improved. Check the label on the unit and if there is a difference, the label on the unit is the correct one.

Please note that with the addition

of thermostat control and outside combustion air supply, this unit is approved for bedroom installations.

296

Minimum Clearances to Combustibles/

Degagement Minimum Des Materiaux

Serial No./

No de Serie

Duplicate Serial No.

DO NOT REMOVE THIS LABEL/ NE PAS ENLEVER CETTE ÉTIQUETTE

For installation into a vented non-combustible

ﬁ replace, listed factory built ﬁ replace. This vented

gas ﬁ replace heater is not for use with air ﬁ lters.

918-488

Combustibles:

Side of unit to wall /

Cote:

A 9"/229mm

Top of unit to

mantle / Au dessus:

B 14"/355mm

Ne peut etre installe que dans un foyer non

combustible muni d'un event. Ne pas utiliser de

ﬁ ltre à air avec ce foyer au gaz à évacuation.

WARNING: This ﬁ replace has been converted for use

with a gas ﬁ replace insert only and cannot be used for

burning wood or solid fuels unless all original parts

have been replaced, and the ﬁ replace re-approved by

the authority having jurisdiction.

ELECTRICAL SUPPLY/ALIMENTATION

ELECTRIQUE:115V60HZ less than/Moins de 2 AMP.

For the State of Massachusetts, installation and repair must be done by a plumber or gasﬁ tter licensed in the Commonwealth of Massachusetts.

For the State of Massachusetts, ﬂ exible connectors shall not exceed 36 inches in length.

For the State of Massachusetts, the appliances individual manual shut-off must be a t-handle type valve.

Listed: VENTED GAS FIREPLACE HEATER

Tested to: ANSI Z21.88b-2003/CSA-2.33b-2003, CGA 2.17-M91

Gas ﬁ red appliance for use at high altitude.

Certiﬁ ed for/Certifee pour: CANADA and U.S.A. Report No. 476-1428-00 (DEC. 2000)

MADE IN CANADA / FABRIQUE AU CANADA

FPI Fireplace Products International Ltd., Delta, B.C., Canada

The State of Massachusetts requires the installation of a carbon monoxide alarm in accordance with NFPA 720 and a CO alarm with battery back up in the same room where the gas appliance is installed.

FIREPLACE INSERT: E21-NG2 E21-LP2 APPAREIL FONCTIONNANT CONCU POUR

Natural Gas (Naturel Gaz) Propane ETRE INSERE DANS UN FOYER

Minimum supply pressure 5.0" WC/C.E. (1.25 kPa) 12.0" WC/C.E. (2.99 kPa) Pression d’alimentation minimum

Manifold pressure high 3.8" WC/C.E. (0.95 kPa) 11.0" WC/C.E. (2.74 kPa) Pression tublure d'échappement élevée

Manifold pressure low 1.1" WC/C.E. (0.27 kPa) 2.9" WC/C.E. (0.72 kPa) Pression tublure d'échappement basse

Altitude 0-2000 ft. 2000 - 4500 ft. 0-4500 ft. L'altitude

(0 - 610m) (610 - 1372m) (0-1372m)

Oriﬁ ce size 43 DMS 44 DMS 54 DMS Grandeur de l’injecteur

Model/ Modele:

E21-NG2

E21-LP2

NOT FOR USE WITH SOLID FUEL. NE PAS UTILISER AVEC DU COMBUSTIBLE SOLIDE.

Maximum input 23,500 Btu/h 22,000 Btu/h 22,500 Btu/h Debit caloriﬁ que maximum

Minimum input 11,750 Btu/h 11,000 Btu/h 11,250 Btu/h Debit caloriﬁ que minimum

4 Regency® E21-2 Gas Fireplace Insert

REQUIREMENTS

MA Code - CO Detector

(for the State of Massachusetts only)

5.08: Modifications to NFPA-54, Chapter 10

(2) Revise 10.8.3 by adding the following additional requirements:

(a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall be satisfied:

1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fueled equipment, the installing plumber or gasfitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is installed on the floor level where the gas equipment is to be installed. In addition, the installing plumber or gasfitter shall observe that a battery operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of qualified licensed professionals for the installation of hard wired carbon monoxide detectors

a. In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level.

b. In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon monoxide detector with an alarm shall be installed.

2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.

3. SIGNAGE. A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight (8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read, in print size no less than one-half (1/2) inch in size, "GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL

OBSTRUCTIONS".

4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR

5.08(2)(a)1 through 4.

(b) EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:

1. The equipment listed in Chapter 10 entitled "Equipment Not Required To Be Vented" in the most current edition of NFPA 54 as adopted by the Board; and

2. Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or structure used in whole or in part for residential purposes.

(c) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the instructions provided by the manufacturer for installation of the equipment and the venting system shall include:

1. Detailed instructions for the installation of the venting system design or the venting system components; and

2. A complete parts list for the venting system design or venting system.

(d) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies "special venting systems", the following requirements shall be satisfied by the manufacturer:

1. The referenced "special venting system" instructions shall be included with the appliance or equipment installation instructions; and

2. The "special venting systems" shall be Product Approved by the Board, and the instructions for that system shall include a parts list and detailed installation instructions.

(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation.

5Regency® E21-2 Gas Fireplace Insert

INSTALLATION

IMPORTANT MESSAGE

SAVE THESE

INSTRUCTIONS

The Regency® Gas Fireplace must be installed in accordance with these instructions. Carefully read all the instructions in this manual ﬁ rst. Consult the "authority having jurisdiction" to determine the need for a permit prior to starting the installation. It is the responsibility of the installer to ensure this ﬁ replace is installed in compliance with the manufacturer's instructions and all applicable codes.

BEFORE YOU START

Safe installation and operation of this appliance requires common sense, however, we are required by the Canadian Safety Standards and ANSI Standards to make you aware of the following:

INSTALLATION AND REPAIR SHOULD BE DONE BY A QUALIFIED SERVICE PERSON. THE APPLIANCE SHOULD BE INSPECTED BEFORE USE AND AT LEAST ANNUALLY BY A PROFESSIONAL SERVICE PERSON. MORE FREQUENT CLEANING MAY BE REQUIRED DUE TO EXCESSIVE LINT FROM CARPETING, BEDDING MATERIAL, ETC. IT IS IMPERATIVE THAT CONTROL COMPARTMENTS, BURNERS AND CIRCULATING AIR PASSAGEWAYS OF THE APPLIANCE BE KEPT CLEAN.

DUE TO HIGH TEMPERATURES, THE APPLIANCE SHOULD BE LOCATED OUT OF TRAFFIC AND AWAY FROM FURNITURE AND DRAPERIES.

WARNING: FAILURE TO INSTALL THIS APPLIANCE CORRECTLY WILL VOID YOUR WARRANTY AND MAY CAUSE A SERIOUS HOUSE FIRE.

CHILDREN AND ADULTS SHOULD BE ALERTED TO THE HAZARDS OF HIGH SURFACE TEMPERATURES, ESPECIALLY THE FIREPLACE GLASS, AND SHOULD STAY AWAY TO AVOID BURNS OR CLOTHING IGNITION.

YOUNG CHILDREN SHOULD BE CAREFULLY SUPERVISED WHEN THEY ARE IN THE SAME ROOM AS THE APPLIANCE.

CLOTHING OR OTHER FLAMMABLE MATERIAL SHOULD NOT BE PLACED ON OR NEAR THE APPLIANCE.

GENERAL SAFETY

INFORMATION

1) The appliance installation must conform

with local codes or, in the absence of local codes, with the current Canadian or National Gas Codes, CAN1-B149 or ANSI Z223.1 Installation Codes.

2) The appliance when installed, must be

electrically grounded in accordance with local codes, or in the absence of local codes with the current National Electrical Code, ANSI/NFPA 70 or CSA C22.1 Canadian Electrical Code.

3) See general construction and assembly

instructions. The appliance and vent should be enclosed.

4) This appliance must be connected to the

speciﬁ ed vent and termination cap to the outside of the building envelope. Never vent to another room or inside a building. Make sure that the vent is installed as per Venting instructions.

5) This appliance may only be installed in a

vented, solid fuel burning masonry, listed factory built ﬁ replace, or zero clearance kit part # 530-936.

6) This appliance is Listed for bedroom

installations when used with a Listed Millivolt Thermostat. Some areas may have further requirements, check local codes before installation.

7) This appliance is Listed for Alcove

installations, maintain minimum Alcove clearances as follows, minimum ceiling height of 53-1/2", minimum width of 48" and a maximum depth of 36".

8) This unit is not approved for installation into

a mobile home.

9) Inspect the venting system annually for

blockage and any signs of deterioration.

10) Any safety glass removed for servicing

must be replaced prior to operating the appliance.

11) To prevent injury, do not allow anyone who

is unfamiliar with the operation to use the ﬁ replace insert.

12) Wear gloves and safety glasses for protection

while doing required maintenance.

13) Ensure adequate combustion and ventilation

air.

14) Under no circumstances should this

appliance be modiﬁ ed. Parts that have to be removed for servicing should be replaced prior to operating this appliance.

15) Installation and any repairs to this appliance

should be done by a qualiﬁ ed service person. A professional service person should be called to inspect this appliance annually. Make it a practice to have all of your gas appliances checked annually.

16) Do not slam shut or strike the glass door.

17) Under no circumstances should any solid

fuels (wood, paper, cardboard, coal, etc.) be used in this appliance.

18) The appliance area must be kept clear and

free of combustible materials, (gases and other ﬂ ammable vapours and liquids).

19) Do not use this appliance if any part has been

under water. Immediately call a qualiﬁ ed service technician to inspect the appliance and to replace any part of the electrical control system and any gas control which has been under water.

20) WARNING: Failure to position

the parts in accordance with the diagrams in this manual or failure to use only parts speciﬁ cally approved with this appliance may result in property damage or personal injury.

21) WARNING: Operation of this

appliance when not connected to a properly installed and maintained venting system or tampering with the blocked vent shut-off system can result in carbon monoxide (CO) poisoning and possible death.

Emissions from burning wood or gas could contain chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

6 Regency® E21-2 Gas Fireplace Insert

aaaaa

aaaaaaaaaa

INSTALLATION

POLICY FOR SOLID

FUEL BURNING &

FACTORY BUILT

The Regency® E21 may be installed and vented into any solid fuel ﬁ replace that has been installed in accordance with the National, Provincial and local building codes and is constructed of noncombustible materials.

1) Installer must mechanically attach the sup-

plied label to the inside of the ﬁ rebox of the ﬁ replace into which the gas ﬁ replace insert is installed.

"WARNING: This ﬁ replace has been converted for use with a gas ﬁ replace insert only and cannot be used for burning wood or solid fuels unless all original parts have been replaced, and the ﬁ replace re-approved by the authority having jurisdiction."

2) Do not cut any sheet-metal parts of the

ﬁ replace, in which the gas ﬁ replace insert is to be installed.

3) If the factory-built ﬁ replace has no gas access

hole(s) provided, an access hole of 1-1/2" (37.5mm) or less may be drilled though the lower sides or bottom of the ﬁ rebox in a proper workmanship like manner. This access hole must be plugged with a non-combustible insulation after the gas supply line has been installed.

4) The ﬁ replace ﬂ ue damper can be fully blocked

open or removed for installation of the gas ﬁ replace insert.

5) The ﬁ replace and ﬁ replace chimney must

be clean and in good working order and constructed of non-combustible materials.

6) The chimney cleanouts must ﬁ t properly.

7) Refractory (ﬁ rebricks), glass doors, screen

rails, screen mesh and log grates can be removed from the ﬁ replace before installing the gas ﬁ replace insert.

8) Smoke shelves, shields and bafﬂ es may be

removed if attached by mechanical fasteners. If any part is removed it must not weaken the structural integrity of the factory built.

9) Trim panels or surrounds shall not seal

ventilation openings in the ﬁ replace.

FIREPLACES

INSTALLATION

CHECKLIST

1) Locate your appliance. Refer to the "Clear-

ances to Combustibles" and "Minimum Fireplace Clearances" sections.

2) Make gas and electrical connections. Refer

to the "Gas Connection" section.

Test the pilot. Must be as per diagram in the

"Valve Description" section.

3) Install Flue Connector. Refer to the "Flue

Connector Installation" section.

4) Install vent. Refer to the "Venting" section.

5) Test Gas pressure. Refer to the "Gas Pipe

Pressure Testing" section.

Check aeration. Refer to the "Gas Insert

Aeration System" section.

6) Test for ﬂ ue spillage. Refer to the "Test for

Flue Spillage" section.

7) Install standard and optional features. Refer

to the following sections where applicable:

a. Brick Panel b. Faceplate & Trim c. Flush Glass d. Flush Louver e. Bay Front f. Full Screen Doors g. Remote Control h. Wall Switch i. Wall Thermostat

8) Final check. Refer to the "Final Check"

section.

Before leaving this unit with the customer, the installer must ensure that the appliance is ﬁ ring correctly and operation fully explained to customer.

This includes:

1) Clocking the appliance to ensure the correct

ﬁ ring rate (rate noted on label) after burning appliance for 15 minutes.

2) If required, adjusting the primary air to ensure

that the ﬂ ame does not carbon. First allow the unit to burn for 15-20 min. to stabilize.

3) Ensure that the appliance is venting

correctly.

CAUTION: Any alteration to the product that causes sooting or carboning that results in damage is not the responsibility of the manufacturer.

MINIMUM FIREPLACE

CLEARANCES

Diagram shows the minimum ﬁ replace opening required to be able to install the Regency® gas ﬁ replace insert.

aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa aaaaaaaa

Note: If you are installing the Molded Faceplate, the minimum fireplace dimensions are as follows:

Width (at front): 29-1/8" (740mm) Depth: 15" (381mm) Height: 18-5/8" (473mm)

7Regency® E21-2 Gas Fireplace Insert

aaa

aaaaa

INSTALLATION

CLEARANCES TO COMBUSTIBLES

The minimum clearance from the side of the appliance to a combustible side wall is 9 inches (229mm). The minimum clearance from the top of the louver to a combustible mantel is 14 inches (356mm). The minimum height from the top of the louver to the ceiling is 36 inches (914mm).

Note: A non-combustible mantel may be installed at a lower height

if the framing is made of metal studs covered with a noncombustible board.

8 Regency® E21-2 Gas Fireplace Insert

INSTALLATION

GAS CONNECTION

Only persons licensed to work with gas piping may make the necessary gas connections to this appliance.

The gas connection is a 3/8" NPT accessible on the left side of the unit. The gas line connection may be made of rigid pipe, copper pipe or an approved ﬂ ex connector. (If you are using rigid pipe, ensure that the valve can be removed for servicing.) Since some municipalities have additional local codes it is always best to consult with your local authorities and the CAN/CGA B149 installation code.

For USA installations follow local codes and/or the current National Fuel Gas Code, ANSI Z223.1.

When using copper or ﬂ ex connectors use only approved ﬁ ttings. Always provide a union so that gas lines can be easily disconnected for burner or fan servicing. Flare nuts for copper lines and ﬂ ex connectors are usually considered to meet this requirement.

Important: Always check for gas leaks with a soap and water solution or gas leak detector. Do not use open ﬂ ame

for leak testing.

For minimum and maximum supply pressure see the System Data table.

1) If the appliance is to be installed into an

existing chimney system, thoroughly clean the masonry ﬁ replace that has been chosen for the Regency

2) The appliance is provided with an opening on

the left hand side of the control compartment for the gas line.

Gas Fireplace.

System Data

For altitude: Natural Gas 0-2000 ft. Propane: 0-4500 ft.

Burner Inlet Oriﬁ ce Sizes: Natural Gas Propane

Burner #43 #54

Max. Input Rating

- Natural Gas 23,500 Btu/h

- Propane 22,500 Btu/h

Min. Input Rating

- Natural Gas +/-5% 11,750 Btu/h

-Propane +/-5% 11,250 Btu/h

Supply Pressure

Natural Gas min. 5.0" w.c.

Propane min. 12.0" w.c.

Manifold Pressure (High)

Natural Gas 3.8" +/- 0.2" w.c.

Propane 11" +/- 0.2" w.c.

Circulation Fan: 120 VAC, 60 Hz Variable Speed: 127 CFM, thermally

activated

NATURAL GAS E21-NG2

For altitude: 2000 ft - 4500 ft.

Note: During any pressure testing of the gas supply piping system that exceeds test pressures of 1/2 psig, this appliance and its individual shut-off valve must be disconnected from the piping system. If test pressures equal to or less than 1/2 psig are used then this appliance must be isolated from the piping system by closing its individual manual shut-off valve during the testing.

CAUTION: If the glass is removed for servicing, it must be replaced prior to operating the appliance. The glass must be fixed in the closed position when operating.

Burner Inlet Oriﬁ ce Size: 44 DMS

Max. Input Rating 22,000 Btu/h

Min. Input Rating +/-5% 11,000 Btu/h

HIGH ELEVATION

This unit is approved in Canada for altitude 0 to 4500 ft. (CAN/CGA 2.17-M91) with the oriﬁ ce supplied.

9Regency® E21-2 Gas Fireplace Insert

INSTALLATION

WIRING DIAGRAMS

This heater does not require a 120V A.C. supply for operation. In case of a power failure, the burner switch and the optional remote control/ thermostat will continue to operate. However, a 120V A.C. power supply is needed for the fan/blower operation.

For NATURAL GAS Units and Units NOT Equipped with DC Spark Boxes

#8 Ground Lug

Nut

Lockwasher

Star washer

Nut

Star washer

Grounding

Lug Detail

Fan ground

Power cord ground wire

Pilot

Assembly

Caution: Ensure that the wires do not touch any hot surfaces and are away from sharp edges.

When connected with 120 volts, the appliance must be electrically grounded in accordance with local codes or, in the absence of local

Neutral

Live

60 Hz

Thermodisc

Gas Pilot

Thermopile

Electrode

120V AC

codes the current CSA C22.1 (in Canada) or with the National Electrical Code ANSI/NFPA 70-1987 (in USA).

NOTE: This unit is equipped with a heat

sensor thermodisc which will prevent the blower from operating until the unit reaches the correct temperature.

Ground

Green

Fan

ON OFF

Fan

Red

Black

Rotary Speed

Control

Black

Thermocouple In

Gas In

I P

White

Brown

"S.I.T" Valve

CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation.

Piezo

Ignitor

Red

ONOFF

Vent Spill

Switch

(Auto Reset)

Remote

Receiver

(Optional)

(Millivolt)

WARNING: Electrical Grounding

Instructions This appliance is equipped with a three pronged (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding prong from this plug.

Thermostat

(Millivolt)

(Optional)

Black

Red

Remote Transmitter

Burner

OFF

(Optional)

Regency

10 Regency® E21-2 Gas Fireplace Insert

+ 22 hidden pages

Regency E21-NG2, E21-LP2 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual