Red Lion XCGSM User Manual

Bulletin No. XCGSM- A
Drawing No. LP0782
Released 02/10

Tel [phone]
Fax [phone]
www.redlion.net

MODEL XCGSM – GSM/GPRS CELLULAR MODEM OPTION CARD FOR
DATA STATION PLUS AND MODULAR CONTROLLER

 CONFIGURED USING CRIMSON® SOFTWARE
 INSTALLS INSIDE A DATA STATION PLUS OR A MODULAR

CONTROLLER

 INSTALLATION AND CONNECTION HARDWARE ARE INCLUDED

WITH CARD

GENERAL DESCRIPTION

The XCGSM option card allows the user to add GSM/GPRS cellular modem
capability to their Data Station Plus or Modular Controller. GSM/GPRS is the
most prevalent cellular technology in today’s markets. GPRS can be used for
services such as Wireless Application Protocol (WAP) access, Short Message
Service (SMS), and for Internet communication services such as email and
World Wide Web access. The XCGSM modem option card is quad-band,
allowing it to work in frequencies across the Americas, Europe and Asia. US
and Canada work in the 850/1900 MHz bands, while Europe, Middle East,
Africa and most of Asia work in the 900/1800 MHz GSM/GPRS frequencies.

The XCGSM requires the addition of a SIM (Subscriber Identity Module)
card, which is inserted into the holder prior to installation of the XCGSM card.
The SIM card securely stores the service-subscriber key (IMSI) used to identify
a subscriber, and is used to connect to the network to obtain an IP address from
the provider.

The XCGSM communication card is easily installed by removing the blank
expansion port cover of your Modular Controller or Data Station Plus, and
plugging the XCGSM card into the expansion port. Configuration is simple
using Red Lion’s free Crimson® 2.0 software.

SAFETY SUMMARY

All safety related regulations, local codes and instructions that appear in the
literature or on equipment must be observed to ensure personal safety and to
prevent damage to either the instrument or equipment connected to it. If
equipment is used in a manner not specified by the manufacturer, the protection
provided by the equipment may be impaired.

Do not use the controller to directly command motors, valves, or other
actuators not equipped with safeguards. To do so can be potentially harmful to
persons or equipment in the event of a fault to the controller.

CAUTION: Risk of Danger.

Read complete instructions prior to

installation and operation of the unit.

ORDERING INFORMATION

MODEL NO. DESCRIPTION PART NUMBER

XCGSM GSM/GPRS Cell Modem Option Card XCGSM000

1

2

2

G3QANT00
SFCRM200

SFCRM2MC

ANT Quad band GSM/GPRS Cellular antenna
SFCRM2 Crimson 2.0 with G3/Data Station Manual
SFCRM2 Crimson 2.0 with Modular Controller Manual

1

G3QANT00 is a 6 inch direct mount Quad-band antenna.

2

Use these part numbers to purchase Crimson 2.0 on CD with a printed

manual, USB cable and RS-232 cable. Otherwise, download free of charge

from www.redlion.net.

CONTENTS OF PACKAGE

- XCGSM option card

- This hardware bulletin

SPECIFICATIONS

1. POWER REQUIREMENTS: 24 V @ 125 mA max. Power is supplied to

the option card from the main board of the Modular Controller Master or
Data Station Plus.

2. ANTENNA CONNECTOR:

SMA Female connector requires:

50 Ohm antenna with SMA male connector
Quad-band antenna (850/900/1800/1900 MHz) for global support.
Dual-band (850/1900 MHz) antenna for US and Canada only
Dual band (900/1800 MHz) for Europe only

The antenna cable should be 50  impedance, RG178/U or RG174/U type

and be able to connect to the RSMA (Male) jack bulkhead. The antenna
could be horizontal, vertical or right angled. Longer antenna cable would
equate to signal loss.

This device is intended for connection to an antenna mounted within the

building or a UL certified enclosure suitably rated for application.

3. CERTIFICA TIONS AND COMPLIANCES:

Refer to main unit manual or “Agency Approvals” section of Red Lion’s

website for agency certifications.

ELECTROMAGNETIC COMPATIBILITY

Emissions and Immunity to EN 61326: Electrical Equipment for

Measurement, Control and Laboratory use.

Reference Modular Controller Master or Data Station Plus unit for EMC

specifications

The XCGSM option card has been tested and found to comply with the limits

for a Class A digital device, pursuant to part 15 of the FCC rules.

4. ENVIRONMENTAL CONDITIONS:

Refer to the specifications of the Modular Controller Master or Data Station

Plus you are installing this card in.

5. CONSTRUCTION: For indoor use only. Installation Category II, Pollution

Degree 2.

6. INSTALLATION REQUIREMENTS: See “Installing the XCGSM Option

card” for more details.

7. WEIGHT: 3.2 oz (94.64g)

1

INSTALLING THE XCGSM OPTION CARD

The first step is to buy a SIM Card from one of the GSM/GPRS providers and
insert it into the SIM Card slot of the option card. The SIM Card slot is the
rectangular slot on top of the GSM/GPRS Cellular Modem in the XCGSM
option card as shown in Figure 1. See SIM Card details in the Software/Unit
Operation Section for more details.

1. Remove power from the unit.

2. Insert a flat-bladed screwdriver into the slot at the top of the expansion port

cover. Gently apply pressure on the screwdriver in an upward direction until

the expansion port cover disengages from the unit as shown in Figure 2.

3. Verify that the option card knobs are in the “unlocked” position as shown in

Figure 3.

4. Carefully insert the option card into the expansion port opening while

aligning the card-edge connector on the option card with the main board's

header, as shown in Figure 4. Once aligned, gently press on the front of the

card until it is flush with the front of the case.

5. Turn the option card knobs to the locked position as shown in Figure 5.

6,0&$5'

Caution: The expansion and main circuit boards contain static

sensitive components. Before handling the cards, discharge static
charges from your body by touching a grounded bare metal object.
Ideally, handle the cards at a static controlled clean workstation.
Also, handle the cards by the edges only. Dirt, oil, or other
contaminants that may contact the cards can adversely affect circuit
operation.

Warning: Risk of Danger: Be sure to remove all power before

removing the expansion port cover.

XCGSM

Figure 1

*60*356&(//02'(0

XCGSM

XCGSM

Figure 2

Figure 3

THE OPTION CARD LABEL

Place the option card label on your outer plastic cover of the
Modular Controller Master or Data Station Plus. The label displays
the FCC ID of the particular modem being used in the XCGSM card.

Figure 4

Figure 5

2

POWER SUPPLY REQUIREMENTS

NEW AND EXISTING INSTALLATIONS

The XCGSM option card draws all of its power from the main board of the
Modular Controller Master or Data Station Plus. The specifications of the
Modular Controller Master or Data Station Plus account for the power needs of
an option card.

SOFTWARE / UNIT OPERATION

CRIMSON SOFTWARE

Crimson® 2.0 software is available as a free download from www.redlion.net
or it can be purchased on a CD, see “Ordering Information” for part number.
The latest version of the software is always available from the web site, and
updating your copy is free.

CONFIGURING A XCGSM OPTION CARD

The XCGSM is configured using Crimson® software. Crimson is available as
a free download from www.redlion.net, or it can be ordered on CD. Updates to
Crimson for new features and drivers are posted on the website as they become
available. By configuring the XCGSM using the latest version of Crimson 2.0,
you are assured that your unit has the most up to date feature set. Crimson 2.0
software can configure the XCGSM through the option card selection. After
choosing the Cellular Modem option card, it is set up as a PPP Modem client,
PPP Modem server or SMS via GSM Modem.

All XCGSM option cards are configured to US GSM/GPRS frequency band
(850/1900 MHz) by default. During setup of the Cellular Modem Option card,
the appropriate GSM/GPRS frequency band must be chosen depending on the
geographical location of the Modular Controller or Data Station Plus. Once the
option card is configured through Crimson software, it needs to be downloaded
to the Modular Controller Master or Data Station Plus. The Modular Controller
Master or Data Station Plus with the XCGSM option card needs to be power
cycled for the configuration changes with respect to the GSM/GPRS frequency
band to take effect.

Additional information can be found in your Modular Controller Master or
Data Station Plus hardware bulletin and the Crimson 2.0 user manual.

SIM CARD INSTALLATION & DETAILS

A SIM Card has to be installed on the XCGSM option card before installing

the option card in the Modular Controller Master or the Data Station Plus.

TROUBLESHOOTING YOUR XCGSM OPTION
CARD

If for any reason you have trouble operating, connecting, or simply have
questions concerning your new XCGSM option card, contact Red Lion’s
technical support. For contact information, refer to the back page of this bulletin
for phone and fax numbers.

EMAIL: [e-mail]

Web Site: http://www.redlion.net

3

The Company warrants the products it manufactures against defects in materials and workmanship

LIMITED WARRANTY

for a period limited to two years from the date of shipment, provided the products have been stored,
handled, installed, and used under proper conditions. The Company’s liability under this limited
warranty shall extend only to the repair or replacement of a defective product, at The Company’s
option. The Company disclaims all liability for any affirmation, promise or representation with
respect to the products.

The customer agrees to hold Red Lion Controls harmless from, defend, and indemnify RLC against
damages, claims, and expenses arising out of subsequent sales of RLC products or products
containing components manufactured by RLC and based upon personal injuries, deaths, property
damage, lost profits, and other matters which Buyer, its employees, or sub-contractors are or may be
to any extent liable, including without limitation penalties imposed by the Consumer Product Safety
Act (P.L. 92-573) and liability imposed upon any person pursuant to the Magnuson-Moss Warranty
Act (P.L. 93-637), as now in effect or as amended hereafter.

No warranties expressed or implied are created with respect to The Company’s products except
those expressly contained herein. The Customer acknowledges the disclaimers and limitations
contained herein and relies on no other warranties or affirmations.

Red Lion Controls
Headquarters
20 Willow Springs Circle
York PA 17406
Tel [phone]
Fax [phone]

Red Lion Controls

Europe

Printerweg 10

NL - 3821 AD Amersfoort

Tel [phone]

Fax [phone]

Red Lion Controls

India

54, Vishvas Tenement

GST Road, New Ranip,

Ahmedabad-382480 Gujarat, India

Tel [phone]

Fax [phone]

Red Lion Controls

China

Unit 101, XinAn Plaza

Building 13, No.99 Tianzhou Road

ShangHai, P.R. China 200223

Tel [phone]

Fax [phone]