Red Lion PMK6A User Manual

1

The panel mount adapter kit is used to mount 1/16 DIN instruments into
existing vertical or horizontal 1/8 DIN panel cut-outs. The kit includes two
black painted durable steel mounting plates and a sponge rubber gasket. The
Adapter Kit, when used with a unit which has NEMA 4/IP65 specifications,
will meet NEMA 4/IP65 requirements when properly installed. Red Lion
Controls 1/16 DIN products include Temperature and Process Control Units
(Models T48, and P48), and the C48 units.

PANEL MOUNT ADAPTER KIT - 1/8 DIN TO 1/16 DIN

DIMENSIONS In inches (mm)

INSTALLATION

TYPICAL VERTICAL MOUNT INSTALLATION

1. Remove the paper backing from the adhesive side of the
adapter gasket (included with adapter kit) and
carefully apply the gasket to the front of the existing
panel cut-out.

2. Carefully remove the center section of the
panel gasket (provided with the unit) and
discard. Slide the panel gasket over the
rear of the unit to the back of the
bezel.

3. Slide the mounting plate
over the rear of the unit
to the back of the unit bezel.

4. Insert the unit with
mounting plate into the
panel cut-out from the front.
Slide the adapter plate over
the rear of the unit. The
protrusion on the adapter
plate is designed to fit into
the existing 1/8 DIN
panel cut-out to properly
position the unit.

5. Refer to the installation
section of the manual,
supplied with the unit, to
complete the installation.

MODEL NO. DESCRIPTION PART NUMBER

PMK6 Panel Mount Adapter Kit (1/8 DIN to 1/16 DIN) PMK60000

ORDERING INFORMATION

ADAPTER PLATE

Bulletin No. PMK6/A-C

Drawing No. LP0481

Released 3/08

Tel [phone]

Fax [phone]

www.redlion.net

MOUNTING PLATE

The panel mount adapter kit is used to mount CUB5 units into existing 1/8
DIN panel cut-outs. The kit includes two black painted durable steel mounting
plates and a sponge rubber gasket. The Adapter Kit, when used with a unit
which has NEMA 4/IP65 specifications, will meet NEMA 4/IP65 requirements
when properly installed. Red Lion Controls CUB5 products include Counters,
Timers, Temperature, Process and Rate units.

PANEL MOUNT ADAPTER KIT - 1/8 DIN TO CUB5

DIMENSIONS In inches (mm)

INSTALLATION

TYPICAL HORIZONTAL MOUNT INSTALLATION

1. Remove the paper backing from the adhesive side of the
adapter gasket (included with adapter kit) and carefully
apply the gasket to the front of the existing panel cut­out.

2. Carefully remove the center section of the panel
gasket (provided with the unit) and discard.
Slide the panel gasket over the rear of the
unit to the back of the bezel.

3. Slide the mounting plate over the
rear of the unit to the back of the
unit bezel.

4. Insert the unit with mounting plate
into the panel cut-out from the
front. Slide the adapter plate over
the rear of the unit. The
protrusion on the adapter plate is
designed to fit into the existing
1/8 DIN panel cut-out to properly
position the unit.

5. Refer to the installation section of
the manual, supplied with the unit,
to complete the installation.

ORDERING INFORMATION

MOUNTING PLATE ADAPTER PLATE

MODEL NO. DESCRIPTION PART NUMBER

PMK6A

Panel Mount Adapter Kit (1/8 DIN to CUB5) PMK6A000

Red Lion Controls

20 Willow Springs Circle

York PA 17406

Tel [phone]

Fax [phone]

Red Lion Controls AP

Unit 101, XinAn Plaza

Building 13, No.99 Tianzhou Road

ShangHai, P.R. China 200223

Tel [phone]

Fax [phone]

Red Lion Controls BV

Printerweg 10

NL - 3821 AD Amersfoort

Tel [phone]

Fax [phone]