RCA DTA809L User Manual

user manual

manual de usuario

DTA809

DTA809L

www.1800customersupport.com/RCA

Es importante leer este manual antes de usar por vez primera su equipo.

rst time.

FCC information

WARNING:

DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD,

This con vert er bo x has earned the ENERGY STAR.

This symbol indicates that this product incorporates double insulation between the hazardous mains voltage and user accessible parts.

Ventilation

You must adequately ventilate the product. Make sure there

for ventilation. See diagram.

This device complies with Par t 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interferen

ce received, including

interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful inter ference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a partic ular installation . If this equipment does cause harmful interference to radio or television reception,

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connec t the equipment int o a n outlet on a cir cuit

erent from that to which the receiver is connected.

• Consult the dealer o r an experience d radio/TV

technician for help.

WARNING: Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

10 cm

7 cm

10 cm

7 cm

10 cm

7 cm

10 cm

7 cm

For your safety

The AC power plug is polarized (one blade i s wider than the other) and only ts into AC power outlets one w ay. If the plug won’t go into the outlet completely, turn the plug over and try to insert it the other

t, contact a

erent

one. Do not attempt to bypass this safety feature.

Removing the power plug is the only way to completely remove power from your product. Make sure the power plug remains easily accessible.

For your records

Keep your sales receipt for proof of purchase to obtain warranty parts and service. In the event that service should be required, you may need both the model number and the serial number. In the space below, record the date and place of purchase, and the serial number:

Date of Purchase : Place of Purchase : Serial No. :

Important safety instructions

Please read and save for future reference

Some of the following information may not apply to your particular product; however, as with any electronic product, precautions should be observed during handling and use.

• Read these instructions.

• Keep these instructions.

• Heed all warnings.

• Follow all instructions.

• Do not use this apparatus near water.

• Clean only with dry cloth.

• Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

• Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including ampli ers) that produce heat.

• Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not  t into your outlet, consult an electrician for replacement of the obsolete outlet.

• Protect the power cord from being walked on or

pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

• Only use attachments/accessories specified by the

manufacturer.

• Use only with the cart, stand, tripod,

bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

• Unplug this apparatus during lightning storms or when

unused for long periods of time.

• Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally,

or has been dropped.

Portable Cart Warning

Additional safety information

• Apparatus shall not be exposed to dripping or splashing

and no objects  lled with liquids, such as vases, shall be placed on the apparatus.

• Always leave sufficient space around the product for

ventilation. Do not place product in or on a bed, rug, in a bookcase or cabinet that may prevent air flow through vent openings.

• Do not place lighted candles, cigarettes, cigars, etc. on the product.

• Connect power cord only to AC power source as marked on the product.

• Care should be taken so that objects do not fall into the product.

• Do not attempt to disassemble the cabinet. This product does not contain customer serviceable components.

• Where the main plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.

If your product operates on batteries

Adhere to the following precautions: A. Any battery may leak electrolyte if mixed with a

different battery type, if inserted incorrectly, or if all batteries are not replaced at the same time.

B. Any battery may leak electrolyte or explode if disposed

of in  re or an attempt is made to charge a battery not intended to be recharged.

C. Discard leaky batteries immediately. Leaking batteries

can cause skin burns or other personal injury. When discarding batteries, be sure to dispose of them in the proper manner, according to your state/provincial and local regulations.

D. Battery shall not be exposed to excessive heat such as

sunshine,  re or the like.

Rating plate location

The rating plate is located on the bottom of the unit.

Important battery precautions

• Any battery may present a risk of fire, explosion, or chemical burn if abused. Do not try to charge a battery that is not intended to be recharged, not incinerate, and do not puncture.

• Non-rechargeable batteries, such as alkaline batteries, may leak if left in your product for a long period of time. Remove the batteries from the product if you are not going to use it for a month or more.

• If your product uses more than one battery, do not mix types and make sure they are inserted correctly. Mixing types or inserting incorrectly may cause them to leak.

• Discard any leaky or deformed battery immediately. They may cause skin burns or other personal injury.

• Do not expose batteries to excessive heat (for example, by leaving them in sunlight or close to  re).

• Please help to protect the environment by recycling or disposing of batteries according to federal, state, and local regulations.

Contents

Box contents ..........................................................4

Setting up ..............................................................4

Program the supplied remote control ................6

General controls ....................................................7

Menu settings ........................................................8

Display 16:9 contents ........................................ 11

Watching non-digital over-the-air TV broadcasts

.............................................................................. 12

Closed captioning on the Converter Box ......... 12

More information ............................................... 13

Box contents

The following items are included:

RCA Digital TV Converter Box

Quick Start Guide

User Manual (this booklet)

RF coaxial cable

2 AAA Batteries

Remote control

Setting up

Step 1: Installation

The Converter Box can be installed either horizontally or vertically. The left side of the Converter Box can be rotated as a stand for vertical installation.

Bottom view

Vertical installation (recommended) Horizontal installation

Step 2: Connections

Option 1: Basic connection to TV

(Optional)

From antenna

AC120V

60Hz

Connect your existing antenna cable to the

ANTENNA IN jack of the Converter Box. Connect the RF coaxial cable (supplied) from the

OUTPUT TO TV jack of the Converter Box to the ANTENNA jack of the TV set.

Slide the CH3/CH4 selector on the back of the

Converter Box to the channel that is not in use in your area. The Converter Box will send its video signal to either Channel 3 or 4 on your TV.

Connect the Audio/Video cables (not supplied) from

the AUDIO / VIDEO output jacks (yellow, white, red) of the Converter Box to the Audio/Video IN jacks on the TV set. If there are more than two sets of Audio/ Video jacks on the TV set, connect only either INPUT1 or INPUT2 to those of your converter box.

Connect the AC power cable of the Converter Box to

a suitable wall outlet.

Tip:

Using the optional Audio/Video cable connection provides better picture quality in case your TV set has Audio/Video input available.

Note:

You may choose to connect the RF coaxial cable to TV, or Audio/Video cables to T V, or both the RF coaxial cable and AV cables to TV.

Setting up (continue)

Option 2 : If you also need to connect your VCR

Connect your existing antenna cable to the

ANTENNA IN jack of the Converter Box. Connect the RF coaxial cable* (supplied) from the

OUTPUT TO TV jack of the Converter Box to the ANTENNA IN jack of the VCR.

Connect the RF coaxial cable* (not supplied) from the

ANTENNA OUT jack of the VCR to the ANTENNA IN jack of the TV set.

Slide the CH3/CH4 selector on the back of the VCR to

the channel that is not in use in your area. The VCR will send its video signal to either Channel 3 or 4 on your TV.

Slide the CH3/CH4 selector on the back of the

AC120V

60Hz

From antenna

* You can also use Audio/Video cables (similar to option 1) if the connection jacks are available on the VCR and TV.

Note:

The SMART ANTENNA IN jack lets you connect a Smart Antenna. Refer to the antenna’s user manual for proper connection. Smart Antenna provides improved reception. For more information, please consult your TV dealer.

Converter Box to the channel that is not being used by the VCR; e.g., if you set the VCR selector to CH3, slide the Converter Box selector to CH4.

Connect the AC power cable of the Converter Box to

a suitable wall outlet.

Step 3: Initial setup of the Converter Box

1. Press BOX on the remote control to turn on the Converter Box. The indicator on front panel will turn yellow (ON

mode) form red (STANDBY mode).

• Make sure your TV is on the correct channel (either 3 or 4) or VIDEO mode. Refer to your TV manual for further instructions.

• The following screen can be seen on your TV when the correct channel is chosen.

• If you cannot see the above screen on your TV set, check if : a) the converter box has been turned on, b) your TV is on the correct channel (either 3 or 4) or VIDEO mode. Refer to

your TV manual for further instructions.

c) you have correctly connected the TV set with the Converter Box.

• If you still do not see the above screen, follow the following steps to reset the Converter Box to factory reset status:

- From the “No Signal” screen, press MENU key ;

- Press “5”, “ 6”, “2” then you should see the above screen and please continue the setup.

2. Press 1 (for English), 2 (for Spanish) or 3 (for French) to select the menu language.

Setting up (continue)

3. Press 1 to start automatic channel search.

• When the scan  nishes, the Channel List menu displays the found channels.

• Reposition the antenna and perform the automatic channel scan again if you cannot find all available channels by pressing MENU key.

• The Converter Box is also compatible with Smart Antennas which can provide improved reception over standard indoor antennas.

• If a Smart Antenna is connected, press 1 for Quick Scan or 2 for Full Scan. A full scan with Smart Antenna may take around 40-50 minutes.

Program the supplied remote control

You can control TV sets of all major brands after programming the Converter Box remote control with the PGM key. RCA TV sets can be controlled directly without programming. Refer to the steps below and the separate Program Code leaflet to guide you through the programming.

1. Refer to the Program Code at the last pages of this booklet. Look for the brand of your TV set and a 3-digit program code next to it. There may be more than one program code available. Choose any one of them.

Program codes/Códigos de programa

Admiral 002, 128, 183, 189 Advent 191, 258, 260, 275 Adventura 129

4. The Channel List is displayed once scanning is  nished

or to select channel and OK to start viewing.

Press

• You may also hide unwanted channels, refer to “Channel List” on page 8 for details.

Your Converter Box is now ready for use!

Tip:

To continue to view non-digital TV broadcasts, if available, press the BOX on your remote to place the Converter Box in stand-by mode (red light), then switch your TV to channel 3 or 4 (depending on which channel the Converter’s CH3/CH4 selector switch is set to).

You must have the RF coaxial cable connected to your TV input, in order to watch non-digital TV broadcasts.

3. Enter the 3-digit program code with the number keys. Press OK for confirmation. The signal indicator will be o when the program is done.

4. Press the volume keys on this remote control to check if they can adjust the volume of your TV set.

2. Press PGM on the remote control. The signal indicator

on it remains lit.

signal indicator

• If you fail to control your TV set, repeat steps 2 to 4 to program again. Try another program code if there is more than one for your TV brand.

• If the signal indicator remains lit after blinking four times, you may have entered the wrong code. Repeat steps 3 to 4 to program again. Make sure you have correctly entered the code.

• You can still use your TV remote control to turn on your TV set, select input source and control the volume.

General controls

• The keys on the Converter Box remote control are divided into two parts. The keys shown in white in the diagram below control the Converter Box, while the grey keys control your TV set.

• You can control TV sets of all major brands after programming this remote control with the PGM key. RCA TV sets can be controlled directly without programming. Refer to “Program the supplied remote control” section for details.

TV controls ONLY

Turns the TV on or o

Selects CH3, CH4 or AV INPUT on the TV

Mutes or restores sound output from the

TV (if the TV supports this function)

Adjusts the TV volume

Programs the remote control so that it can

control your TV set. Refer to “Program the

supplied remote control” for details

Insert 2 “AAA” batteries

prior to use.

Signal indicator

Turns the converter box on or o

Navigates through the converter box menus (e.g., to move right, press ) Press OK to con rm menu selections

Shows or hides channel information (it is possible to receive some programs from di erent time zones, the time information might be wrong in this case)

Shows or hides the main menu

Selects the previous or next channel

Selects channels by inputting the channel number

Shortcut keys to access functions in the main menu

Displays closed captioning from the converter box

Inputs a dash (e.g., 12-1) while selecting an ATSC channel with the number keys (0-9)

Menu settings

The main menu lets you access more features of the converter box. Press MENU to show or hide the menu. When the menu is displayed, press the number keys on the remote control to access the corresponding menu item directly.

Shortcut key

Channel List

• Lists the available TV channels and the programs playing on each channel.

• To change channels, select a channel number and press OK.

• To skip a channel when pressing the CHANNEL button, select “Stored” next to the channel name and then press OK . The status changes to “Skipped”.

Shortcut key

AV Settings

• Change the video display and sound output formats.

• Press 1 for Picture or 2 for Audio Controls. – Picture : Press 1 for Widescreen or 2 for Fullscreen . – Audio Controls : Press 1 for Stereo, or 2 for Alternate

Audio (for bilingual programs). When Alternate Audio is selected, press OK on the remote control to switch between main and alternate languages while watching TV.

Shortcut key

Ratings

• This feature enables you to restrict access to certain TV programs whose content may be deemed unsuitable for your children. Viewing is restricted unless the password (initial default password: 0000) that you have chosen is entered. Password is also required before entering the rating menu.

• Three sub-menus are available:

Select

“Stored”

channels

12.1

12.2

12.3

12.4

Stored

Skipped

Stored

Select any channels

including “Skipped” ones

• Press 1 for Lock/Unlock: to activate or deactivate the rating feature.

Lock/Unlock : Press 1 to select OFF (to de-activate

the rating feature, even if you have defined certain settings in the Rating Limits menu) or press 2 to select ON (to activate the rating feature) or press 3 to select ON/ Enable (to activate the rating feature and enable downloadable ratings).

Menu settings

• Press 2 for Rating Limits

Rating Limits: Press 1 for T V Shows, press 2 for Movies,

press 3 for Custom (only available when ON/Enable is selected in Lock/Unlock menu)

• TV Shows: To change the TV parental ratings by

pressing OK against desired rating level. A padlock icon tells you whether or not a rating level is locked.

TV-Y

TV-Y7

TV-G

TV-PG

TV-14

TV-MA

DDL

– In the above example, all TV programs rated

above TV-PG require the password for viewing.

• Movies: To change the movie parental ratings by

pressing OK against desired rating level. A padlock icon tells you whether or not a rating level is locked.

G - 1

PG - 2

PG-13 - 3

R - 4

NC-17 - 5

X - 6

NR - 7

– In the above example, all movies rated PG or

above require the password for viewing.

• Custom: To update the current TV show and Movies ratings when new releases are available. – Press the corresponding number key to select

the program restrictions. They include: Entire Audience (1), Dialogue (2), Language (3), Sex (4), Violence (5), Children (6), Fantasy violence (7), MPAA (8).

• Press 3 for Change PIN To change the password for ratings. The initial default password is “0000”, you must change

it and create your own password to activate the rating settings.

Tip:

After the rating settings are done, do not forget to activate them by selecting ON in the Lock/ Unlock menu.

Parental Controls, popularly known as the “V-Chip,” depend on information sent by broadcasters about specific programs. Two ratings systems are available for you to use to screen inappropriate content for your family.

TV shows can be rated by broadcasters based on the following Age and Content-based Guidelines:

• TV-Y (All Children – This program is designed to be

appropriate for all children.)

• TV-Y7 (Directed to Older Children – This program

is designed for children age 7 and above.) The program may contain fantasy violence (FV).

• TV-G (General Audience – Most parents would this

program suitable for all ages.)

• TV-PG (Parental Guidance Suggested – This program

contains material that parents may unsuitable for younger children.) The program may contain one or more of the following: moderate violence (V), some sexual situations (S), infrequent coarse language (L), or some suggestive dialogue (D).

• TV-14 (Parents Strongly Cautioned – This program

contains some material that many parents would find unsuitable for children under 14 years of age.) Parents are strongly urged to exercise greater care in monitoring this program and are cautioned against letting children under the age of 14 watch unattended. This program contains one or more of the following: intense violence (V ), intense sexual situations (S), strong coarse language (L), or intensely suggestive dialogue (D).

• TV-MA (Mature Audience Only – This program is

designed to be viewed by adults and therefore may be unsuitable for children under 17.) This program contains one or more of the following: graphic violence (V), explicit sexual activity (S), or crude indecent language (L).

Menu settings

Some programmers use the Movie Ratings (MPAA) System to rate TV shows on the same scale as motion pictures:

• A G -rated motion picture contains nothing in

theme, language, nudity, sex, violence or other matters that would offend parents whose younger children view the motion picture.

• A PG -rated motion picture should be investigated

by parents before they let younger children attend.

• A PG-13 rating is a sterner warning to parents to

determine whether their children under age 13 should view the motion picture, as some material might not be suited for them.

• An R -rated motion picture contains some adult

material.

• An NC-17 rated motion picture is one that most

parents would consider too adult for their children.

• X rating is adults only.

• NR is not rated.

For more information about TV ratings, visit: www.PauseParentPlay.org

Shortcut key

Closed Captioning

• Lets you change the closed caption appearance (font, text color, text opacity, background color, background, edge e ect and edge color).

• Press 1 (Font Options) to change font color and e ects, 2 (Back Options) to change background color and e ects or 3 (Default) to reset to default settings.

• Only digital closed captions can be changed.

• For more information, see “Advantages of closed captioning on the Converter Box”.

Shortcut key

Settings

• Six sub-meus are available:

• Press 1 for Channel Scan

– To start automatic channel scan. – To scan more channels (Scan Add) after adjusting

your antenna

– Enable the “Scan Add” option if you only want to

scan more channels with keeping existing channel list.

• Press 2 for Language

– To select the menu language.

• Press 3 for Power Saver

– An energy saving feature to turn off the converter

box automatically after 4 (default), 8 or 12 hours according to your selection. Select OFF to de-activate this feature.

– The timer is only active when the converter box

remains idle (i.e. no key activation). Once any “Box” key is pressed, the timer will be reset.

– If you have set up timer recordings for TV programs,

make sure the converter box will not turn oautomatically before the recordings  nish.

• Press 4 for Antenna

– To show the signal strength for receiving broadcast

from a TV station. If signal is weak, you may need to reposition the antenna.

• Press 5 for Time Zone

– To select your local time zone – To enable or disable Daylight Saving Time.

• Press 6 for System Reset

– To restore all settings to factory defaults.

+ 22 hidden pages