RCA DRD455RH User Manual

Satellite Receiver

User’s Guide

Changing Entertainment. Again.

Important Information

Cautions

Do not stack electronic components or other objects on top of the Digital Satellite Receiver. The slots on top of the receiver must be left

uncovered to allow proper airﬂow to the unit. Blocking the airﬂow to the unit could impair performance or damage your receiver and other components.

Remove any sales or promotional materials attached to the product.

Do not stack the digital satellite receiver on top of a “hot component” such as an audio power ampliﬁer.

FCC Regulations state that unauthorized changes or modiﬁcations to this equipment may void the user’s authority to operate it.

Note to Cable TV Installer:

This reminder is provided to call your attention to article 820-40 of the National Electrical Code (Section 54 of the Canadian Electrical Code, Part

1) which provides guidelines for proper grounding and, in particular, speciﬁes that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical.

Note to Satellite Dish Installer:

This reminder is provided to call your attention to articles 810 and 820 of the 1999 National Electrical Code. Refer to article 810, in particular to 810-1 and 810-15, for required grounding of the metal structure of the Dish Antenna. Refer also to the 810-2 which, by reference to article 820, requires that the satellite dish coaxial cable shield be connected to the grounding system of the building as close to the point of cable entry as practical.

Care and Cleaning:

Use a soft cloth or dusting attachment of your vacuum cleaner to dust your digital satellite receiver. Remove dust from the ventilation holes on the top and bottom.

Plastic surfaces are easily scratched and can be marred by alcohol and various solvents. Avoid excessive use of oil-based furniture polishes since the materials used in the cabinet will accumulate more dust. A non-abrasive, anti-static cleaner/polisher is recommended.

Product Registration

Please fill out the product registration card (packed separately) and return it immediately, or register online at rca.com. Returning the card allows us to contact you if needed.

Product Information

Keep your sales receipt to obtain warranty parts and service and for proof of purchase. Attach it here and record the serial and model numbers in case you need them. These numbers are located on the product.

Model No. ______________________________________________

Serial No. _______________________________________________

Purchase Date: __________________________________________

Dealer/Address/Phone: ____________________________________

WARNING

To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. The apparatus shall not be exposed to dripping or splashing. No objects filled with liquids, such as vases, shall be placed on the apparatus.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

This symbol indicates "dangerous voltage" inside the product that presents a risk of electric shock or personal injury.

This symbol indicates important instructions accompanying the product.

Caution: To reduce the risk of electric shock, do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel.

IMPORTANT NOTICE:

This device incorporates an anticopy process technology that is protected by U.S. patents and other intellectual property rights. The anticopy process is licensed for non-commercial, home use only. Reverse engineering or disassembly is prohibited.

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Table of Contents

Chapter 1: Connections & Setup

Things To Consider Before You Connect Components................ 2

Choose Your Connection................................................................ 2

Insert Your Access Card ................................................................. 2

Excellent Connection ..................................................................... 3

Very Good Connection ................................................................... 4

Basic Connection ............................................................................ 5

Advanced Audio (Digital Audio Output Connection) ................. 6

Jacks and Cables............................................................................. 6

Satellite Receiver Rear Panel ........................................................ 7

Place Batteries in the Remote Control ........................................ 8

Plug in and Turn on the Receiver ................................................. 8

Wait for the Receiver to Download

ADVANCED PROGRAM GUIDE™ Data ....................................... 8

Locating the VCR’s Infrared Remote Control Sensor ................. 9

Using Highlight and Select............................................................ 9

Selecting a VCR Type ................................................................... 10

Complete the Assisted Setup ...................................................... 10

Order Programming...................................................................... 10

Chapter 2: Using the Remote Control

Remote Control Buttons .............................................................. 11

Top of the Digital Satellite Receiver .......................................... 12

Programming the Remote Control ............................................. 12

Testing the Remote Control .............................................................. 12

Using Automatic Code Search .........................................................12

Using Direct Entry ............................................................................... 13

Operating Other Components ..................................................... 13

Modes of Operation ............................................................................13

Controlling a Second RCA Satellite Receiver............................... 13

Chapter 3: Satellite Receiver Features

The Program Guide....................................................................... 16

Displaying the Toolbar ........................................................................ 16

The Channel Banner ..................................................................... 16

The DIRECTV INTERACTIVE™ Feature ......................................... 17

Displaying On-screen Guides ...................................................... 18

The Detail Guide ................................................................................... 18

The Grid Guide ......................................................................................18

Getting Around In the Guides ..................................................... 18

More Details .......................................................................................... 19

Additional Program Guides ......................................................... 20

The Channel Guide .............................................................................. 20

The Logo Guide ..................................................................................... 20

The Suggestion Guide ......................................................................... 20

The Category Guide ............................................................................. 21

The AlphaSort™ Guide ........................................................................21

The Scout™ Guide ................................................................................21

The Profile Guide.................................................................................. 21

The Guide Toolbar ........................................................................ 22

Chapter 4: Using On-Screen Menus

Using the Menu System............................................................... 23

Main Menu Items ......................................................................... 24

The Program Guide....................................................................... 24

Messages ....................................................................................... 25

Mail .......................................................................................................... 25

Caller ID .................................................................................................. 25

Using the Purchases Menu .......................................................... 27

Reviewing and Canceling Upcoming Purchases ......................... 27

Spending Limits .................................................................................... 27

Pay Per View Programs ....................................................................... 27

Timer Recordings .......................................................................... 28

User Profiles .................................................................................. 29

Creating and Editing User Profiles .................................................. 29

Creating a Profile Channel List ........................................................ 29

Setting the Rating Limit ....................................................................30

Viewing Hours ...................................................................................... 30

Setting Up Spending Limits ..............................................................30

Locking a User’s Profile ......................................................................30

Locking the System .............................................................................31

Unlocking the System......................................................................... 31

Choosing Your Profile ......................................................................... 31

Personal Settings.......................................................................... 32

Name .......................................................................................................32

Guide Settings ................................................................................. 32

Channel Banner .................................................................................... 32

Color Scheme ...................................................................................32

Translucency ..................................................................................... 32

Animation ......................................................................................... 32

Edit Fetch ..........................................................................................32

INFO Message ..................................................................................33

System Setup ................................................................................ 33

Assisted Setup ..................................................................................33

Receiver Index ...................................................................................... 33

Receiver Options ..................................................................................34

Dish Pointing ......................................................................................... 36

System Test ............................................................................................ 37

System Info ............................................................................................ 37

System Upgrades ................................................................................. 37

New Access Card ................................................................................. 37

Alternate Data ......................................................................................37

Interactive ..................................................................................... 37

Chapter 5: Other Information

Troubleshooting ............................................................................ 38

Running the System Test ................................................................... 40

Fine-Tuning the Signal ....................................................................... 40

Finding the TV’s Video Line Input.................................................... 40

Limited Warranty ......................................................................... 41

Accessory Information ................................................................. 44

Index .............................................................................................. 45

Chapter 1: Connections & Setup

Things To Consider Before You Connect Components

Protect Your Components from Power Surges

• Connect all components before plugging any power cords into the wall outlet.

• Always turn off the digital satellite receiver, TV and other components before you connect or disconnect any cables.

Position Cables Correctly to Avoid Audio Hum or Interference

• Insert all cable plugs firmly into their jacks.

• Place the Audio/Video (A/V) cables to the sides of the TV’s back panel instead of straight down the middle after you connect your components.

• Try not to coil any twin-lead cables and keep them away from the A/V cables as much as possible.

• Make sure all antennas and cables are properly grounded. See the inside front cover of this book for more information.

Protect Your Components from Overheating

• Do not block ventilation holes in any of the components. Arrange the components so that air can circulate freely. Remove any sales or

promotional materials attached to the product.

• Do not stack components.

• Allow adequate ventilation when placing components in a stand.

• Place an amplifier or receiver on the top shelf of the stand so heated air rising from it will not flow around other components.

Choose Your Connection

There are several ways to connect your digital satellite receiver depending on the components you want to connect and the quality of the signal you want to achieve.

The next four pages show three options for connecting your satellite receiver to your other components, plus instructions for connecting your satellite receiver to a digital audio receiver. Choose the connection that most closely matches your components in order to get the best signal you can. For example, if your TV has component video inputs, use the Excellent Connection shown on the next page as a guide. If your TV only has an RF coaxial input, use the Basic Connection shown on page 5 as a guide.

Page 6 shows the kinds of cables you’ll use to make connections.

Insert Your Access Card

Find the access card in the material that came with your receiver. Make sure the card is facing up, and fully insert it into the slot on the right side of your satellite receiver.

2 Chapter 1

Illustrations contained in this document are for representation only.

Sat

eceiver

RJ11

dula

jack

CH3

Digital

ellite

mo phone

PHONE

VCR

S-VIDEO

– R –

– L –

AUDIO

VIDEO

DIGITAL

AUDIO

LOW SPEED

DATA

OUT TO TV

AUDI

-VIDE

Note: Your VCR and TV back panels may not look exactly like the ones illustrated.

VIDE

FROM

atellite

h Antenn

GROUND

IN FROM ANT

SATELLITE IN

Cable or Off-air Antenna

Connections & Setup

Excellent Connection

Using S-Video and A/V jacks and cables to connect to the TV, RF coaxial cables to connect the VCR

This connection provides the best picture quality, surpassing that of A/V cables. The S-Video cable, which carries video information only, requires that audio cables also be used for sound.

What you will need (see page 6 for descriptions of these cables):

• Two (2) RF coaxial cables

• Two (2) A/V cables

• One (1) S-Video cable

• One (1) telephone line cord

• Coaxial cable lines fed from a digital satellite antenna and a standard TV antenna (or cable line)

Making the Connection

1. Connect the satellite dish antenna feed (RG-6 coaxial cable) to the SATELLITE IN jack on the satellite receiver.

2. Connect one end of an RF coaxial cable to the OUT TO TV jack on the satellite receiver, and the other end to the antenna input jack on the VCR.

Note: If your VCR has A/V input jacks, you can use A/V cables to connect the satellite receiver’s second A/V jacks to the A/V jacks of the VCR instead of using the RF coaxial cable.

3. Connect one end of an RF coaxial cable to the antenna output jack on the VCR, and the other end to the TV’s antenna input jack.

4. Connect the cable or off-air antenna feed (RF coaxial cable) to the IN FROM ANT jack on the satellite receiver.

5. Connect one end of the supplied telephone line cord to the PHONE JACK on the back of the satellite receiver, and the other end to an RJ11-type modular phone jack (the most common type of phone jack).

6. Connect two ends of the supplied A/V cables to AUDIO R and L jacks on the satellite receiver, and the other ends to the corresponding audio input jacks on the TV.

Note: Make sure you connect jacks by their labels. For example, AUDIO R on the digital satellite receiver should be connected to TV’s right audio input jack, L Audio to L Audio, etc.

If your TV only has one audio input jack, use the satellite receiver’s AUDIO L jack to make the connection.

7. Connect one end of the supplied S-Video cable to the satellite receiver, and the other end to the S-Video input jack on the TV.

Go to Page 6

Using Your Components

To watch DIRECTV® programming:

Tune the TV to its S-Video line input (if you have difficulty finding your TV’s S-Video line input, see your TV’s User’s Manual or page 40 in this manual). Then tune the satellite receiver to the desired channel.

To record DIRECTV programming:

Tune the satellite receiver to the desired channel. Then set your VCR to record on the proper input channel (video line input if using A/V cables to connect the VCR to the satellite receiver, channel 3 or 4 if using RF coaxial cable).

To view VCR recordings:

Tune the TV to channel 3 or 4 (whichever is set on the VCR as its output channel). Begin VCR playback as usual.

DIRECTV programming is subject to the terms and conditions of the DIRECTV Customer Agreement; a copy is provided at DIRECTV.com and with your first bill. See page 10 for more information.

Chapter 1 3

Connections & Setup

Sat

eceiver

dula

CH3

RJ11 mo

Digital

ellite

phone jac

PHONE

VCR

S-VIDEO

– R –

– L –

AUDIO

VIDEO

DIGITAL

AUDIO

LOW SPEED

DATA

AUDI

VIDE

Note: Your VCR and TV back panels may not look exactly like the ones shown.

OUT TO TV

atellite

Dish Antenn

GROUND

IN FROM ANT

FROM

SATELLITE IN

Cable or Off-air Antenna

Very Good Connection

Using A/V jacks and cables to connect to the TV, RF coaxial cables to connect the VCR

This connection provides better picture quality than RF coaxial cables and is recommended for use with TVs that do not have S-Video input jacks.

What you will need (see page 6 for descriptions of these cables):

• Two (2) RF coaxial cables

• Three (3) Audio/Video cables

• One (1) telephone line cord

• Coaxial cable lines fed from a digital satellite antenna and a standard TV antenna (or cable line)

Making the Connection

1. Connect the satellite dish antenna feed (RG-6 coaxial cable) to the SATELLITE IN jack on the satellite receiver.

2. Connect one end of an RF coaxial cable to the OUT TO TV jack on the satellite receiver, and the other end to the antenna input jack on the VCR.

Note: If your VCR has A/V input jacks, you can use A/V cables to connect the satellite receiver’s second set of A/V output jacks to the A/V jacks of the VCR instead of using the RF coaxial cable.

3. Connect one end of an RF coaxial cable to the antenna output jack on the VCR, and the other end to the TV’s antenna input jack.

4. Connect the cable or off-air antenna feed (RF coaxial cable) to the IN FROM ANT jack on the satellite receiver.

6. Connect the ends of the supplied A/V cables to the satellite receiver’s AUDIO and VIDEO jacks, and the other ends to the corresponding AUDIO and VIDEO input jacks on the TV.

Notes: Make sure you connect jacks and cables corresponding to their labels. For example, AUDIO R output on the digital satellite receiver should be connected to AUDIO R input on the TV, VIDEO output to VIDEO input, etc.

If your TV only has one audio input jack, use the satellite receiver’s AUDIO L jack to make the connection.

Go to Page 6

Using Your Components

To watch DIRECTV® programming:

Tune the TV to its video line input (if you have difficulty finding your TV’s video line input, see your TV’s User’s Manual or refer to the instructions on page 40 in this manual). Then tune the satellite receiver to the desired channel.

To record DIRECTV programming:

Follow the steps in the previous step, then tune the satellite receiver to the desired channel. Set your VCR to record on its proper input channel (channel 3 or 4).

To view VCR recordings:

Tune the TV to channel 3 or 4 (whichever is set on the VCR as its output channel). Begin VCR playback as usual.

4 Chapter 1

Digital

Sat

eceiver

dula

jack

CH3

ellite

PHONE

VCR

S-VIDEO

Connections & Setup

Basic Connection

RJ11 mo

phone

– R –

– L –

AUDIO

VIDEO

DIGITAL

AUDIO

LOW SPEED

DATA

OUT TO TV

atellite

h Antenn

GROUND

IN FROM ANT

SATELLITE IN

Cable or Off-air Antenna

Using RF Coaxial cables for all connections

This connection provides standard picture quality. This connection is only recommended for use with TVs that do not have S-Video or A/V input jacks.

What you will need (see page 6 for descriptions of these cables):

• Two (2) RF coaxial cables

• One (1) telephone line cord

• Coaxial cable lines fed from a digital satellite antenna and a standard TV antenna (or cable line)

Making the Connection

1. Connect the satellite dish antenna feed (RG-6 coaxial cable) to the SATELLITE IN jack on the satellite receiver.

2. Connect one end of an RF coaxial cable to the OUT TO TV jack on the satellite receiver, and the other end to the antenna input jack on the VCR.

3. Connect one end of an RF coaxial cable to the antenna output jack on the VCR, and the other end to the TV’s antenna input jack.

4. Connect the cable box or off-air antenna feed (RF coaxial cable) to the IN FROM ANT jack on the satellite receiver.

Go to Page 6

AUDI

VIDE

FROM

Note: Your VCR and TV back panels may not look exactly like the ones shown.

Using Your Components

To watch DIRECTV® programming:

Tune the TV to the satellite receiver’s output channel (either channel 3 or 4).

Note: You can change the satellite receiver’s output channel by pressing the remote control’s DIRECTV button, then the MENU button, then select System Setup, then System Options, and finally select Output Channel. Use the remote control’s arrow and SELECT buttons to highlight and select the desired output channel. Tune the TV to that channel to see the satellite receiver’s picture.

To record DIRECTV programming:

Follow the directions in the previous step, then set your VCR to record on its proper input channel (channel 3 or 4 if using RF coaxial cable to make the connection, Video Line Input if using A/V cables to connect the VCR to the satellite receiver).

To view VCR recordings:

Tune the TV to channel 3 or 4 (whichever is set on the VCR as its output channel). Begin VCR playback as usual.

Chapter 1 5

Connections & Setup

Receiver or Decoder with Optical Input

DIGITAL

AUDIO INPUT

Advanced Audio (Digital Audio Output Connection)

Cables: Optical (SPDIF)

Use this connection to take advantage of Dolby Digital* quality sound, when available.

Digital Satellite Receiver

VCR

PHONE

VIDEO

S-VIDEO

Making the Connection

– R –

– L –

AUDIO

DIGITAL

AUDIO

LOW SPEED

DATA

OUT TO TV

GROUND

IN FROM ANT

SATELLITE IN

Note: Your digital receiver back panel may not look exactly like the one pictured.

This satellite receiver’s digital output jack fully complies with the international standard governing this type of jack (IEC958), and will output digital audio signals in either PCM or Dolby Digital format. It is designed for connection to an external Dolby Digital-capable receiver/ decoder.

Older equipment, some of which is not fully compliant with IEC958, may not be compatible with Dolby Digital. If the digital audio output is connected to a receiver that cannot decode Dolby Digital signals, set the Dolby Digital setting in the Receiver Options menu to PCM (see page 35 for further details). Failure to do so could create a high noise level, causing damage to headphones, speakers, or your hearing.

Connect one end of the optical (SPDIF) cable to the DIGITAL AUDIO output jack* on the satellite receiver, and to the digital audio input jack on a Dolby Digital receiver/decoder.

Using Your Component

After you connect your satellite receiver to an A/V receiver that includes a Dolby Digital-capable receiver/decoder, you must select Dolby Digital from the System Options menu (press the remote control’s MENU button, then select System Setup, then Receiver Options, then highlight Dolby Digital. Use the remote control’s arrow and SELECT buttons to highlight and select Autoselect, PCM, or Dolby Digital in order for the receiver to recognize the digital audio connection.

For more information on this feature, see the Dolby Digital entry starting on page 35 in the section, Using The Menu System.

* Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

Jacks and Cables

Below is a description of the jacks and cables you can use to make connections. Not all cables come with your digital satellite receiver.

S-Video Jack and Cable

S-Video jacks/cables provide this receiver’s best picture quality. Remember to connect the left and right audio cables to the

S-VIDEO

TV because the S-Video cable carries only the picture signal, not the sound.

Audio/Video (A/V) Jack and Cable (RCA-type)

Audio/Video (A/V) cables provide good picture quality and stereo sound, and should be used if your TV has no S-video jacks.

VIDEO AUDIO

ANTENNA IN

The digital satellite receiver’s A/V jacks are color coded (yellow for video, red for right audio, and white for left audio). If your TV has only one input for audio (mono), connect it to the left (white) audio jack on the satellite receiver.

RF Jack and Coaxial Cable (F-type)

RF jacks provide good picture and mono sound quality. They should be used if A/V connections are not available on your TV. RF jacks are used for off-air antenna and cable feed connections. The RF jacks on the receiver are labeled IN FROM ANT and OUT TO TV. The coaxial cable supplied with your system is used to connect the receiver to your TV/VCR’s antenna input jack.

VCR Controller

VCR

The VCR Controller plugs into the VCR jack on the satellite receiver’s back panel. Attach the other end of the cable to your VCR’s remote control sensor.

Digital Audio Output (SPDIF)

DIGITAL AUDIO

If you own an A/V receiver that includes a Dolby Digital-compatible decoder, use a digital audio cable to connect the satellite receiver to your external A/V receiver/decoder.

Telephone Jack and Cord

The telephone line cord is required to connect your satellite receiver to a telephone line if you choose to subscribe to

DIRECTV

PHONE

modulator jack (the most common type of phone jack) which might look like one of those pictured here. If you don’t have a modular jack, call your local telephone company to find out how to get one installed.

programming. The phone line connection is used to periodically call out to DIRECTV. You will need an RJ11-type

6 Chapter 1

Connections & Setup

Satellite Receiver Rear Panel

This diagram illustrates each of the back panel jacks found on your digital satellite receiver. When working with cables, be sure to connect corresponding outputs and inputs (Video out to Video in, Right Audio out to Right Audio in, etc.).

PHONE

VCR

S-VIDEO

VIDEO

– R –

– L –

AUDIO

DIGITAL

AUDIO

LOW SPEED

DATA

OUT TO TV

GROUND

IN FROM ANT

SATELLITE IN

For more information on the function of the back panel jacks and many other features of your digital satellite receiver, press the MENU button and select System Setup from the Main menu, then

Back Panel Jacks (in alphabetical order)

select Receiver Index.

AUDIO (R and L) Audio cables offer better sound quality than RF coaxial cables. Connect a second set of audio cables to another component, such as a VCR or stereo.

DIGITAL AUDIO Connects the satellite receiver’s audio to a Dolby Digital-capable receiver or decoder. This audio connection provides the best sound quality. Use the optical DIGITAL AUDIO output cable (SPDIF) for this receiver’s best possible sound.

IN FROM ANT Connect a standard TV antenna or cable feed to the satellite receiver using this jack. You can then switch between the satellite receiver’s signal and the TV/cable feed using the remote control’s ANTENNA button to toggle between the two.

LOW SPEED DATA This port allows you to connect your digital satellite receiver to future services and accessories as they become available. A shielded cable and additional hardware may be required.

OUT TO TV Connects the satellite receiver to your TV or VCR using RF coaxial cable. This jack provides the most basic connection, carrying average sound and video quality.

PHONE Connects the satellite receiver to a telephone line. The digital satellite receiver requires a telephone line connection to periodically communicate with your program provider.

SATELLITE IN Use to connect the satellite receiver to the satellite dish antenna. S-VIDEO Provides better picture quality than VIDEO or RF coaxial cable jacks. If your TV has an S-Video jack, use it along with the audio jacks (S-

Video only carries picture information, not sound) to connect to your TV. VCR This jack allows the satellite receiver to control the VCR using an IR cable. The cable is attached above the VCR’s remote control sensor. This

connection is required for One-Touch Record and Timer recording features. VIDEO Provides better picture quality than the OUT TO TV jack. Connect the second VIDEO jack to another device, such as a VCR. You must also

connect the AUDIO cables when using the VIDEO connection.

Chapter 1 7

Connections & Setup

Place Batteries in the Remote Control

Follow these steps whenever you need to install or change the batteries in your digital satellite receiver’s remote control.

Note: When replacing old batteries, you may need to reprogram the remote control to operate other devices.

Avoid pressing any of the remote control buttons while you’re replacing old batteries. If your press a remote control button while replacing batteries, you will need to reprogram the remote control to operate other devices.

1. Remove the cover from the battery compartment.

2. Insert batteries in the battery compartment, matching the + and – end of each battery.

3. Replace the cover.

Note:

The message “Searching for Satellite Signal” might appear briefly at the bottom of your screen when you turn on your satellite receiver for the first time. This is normal.

If this message stays on the screen for more than one minute, check your receiver’s on-screen signal meter to make sure your antenna is receiving the strongest possible satellite signal. See “Signal Meter” on page 36 for more information.

Note

The Satellite Data Acquisition screen will also appear when:

• your unit loses power (either from a power outage or being unplugged)

• your unit loses the satellite signal for an extended period of time.

Plug in and Turn on the Receiver

Plug the end of the power cord into the wall outlet. Be sure to insert the plug completely. To turn on the satellite receiver, press the DIRECTV button on the remote control or the POWER

button on the front panel. If your TV brand is RCA, GE, or Proscan, press the TV button on the remote control to turn on the TV. If your TV brand is not RCA, GE, or Proscan, see page 12 in the next section, Using the Remote Control, for details on programming the satellite receiver’s remote control to operate your TV.

Wait for the Receiver to Download ADVANCED PROGRAM GUIDE™ Data

The first time you connect a receiver to a satellite antenna you’ve already installed and pointed correctly, the receiver starts to gather information for the program guide.

After you turn on your receiver and tune your TV to the correct video input channel, a progress bar appears indicating that the receiver is gathering this program guide information.

To prevent any damage to your TV screen, the progress bar disappears after 2 minutes (the screen goes blank).

Note: When the progress bar reaches 100%, there might be a delay before you actually see video on the screen.

If the screen stays blank for more than 2 to 3 minutes, you need to reset the receiver.

To reset the receiver:

1. Unplug the satellite receiver’s power cord from the power outlet.

2. Wait a few seconds, and plug the power cord back into the outlet.

3. Turn on the receiver and wait for it to download program guide information.

8 Chapter 1

PHONE

ON OFF

AUX2

ACK

SKIP

MUTE

CLEAR

GUIDE

AUX1

VOL

CH -

(-)

VCR (Front Panel)

Connections & Setup

Locating the VCR’s Infrared Remote Control Sensor

The VCR Controller must be affixed directly over the infrared remote control sensor on your VCR. Some VCRs have a label that identifies the remote control sensor, but others do not. If the IR sensor is

labeled on your VCR, affix the VCR Controller directly over the sensor. For VCRs that do not label the sensor, you can use the VCR’s remote control to locate the VCR’s sensor before affixing the VCR Controller cable.

To Find the VCR’s Remote Control Sensor:

1. Hold the VCR’s remote control so that it is touching the front of the VCR.

2. Slowly move the remote control over the front of the VCR while repeatedly pressing the remote control’s power button.

3. When your VCR turns on/off, you have located the remote control sensor.

Note: To test the VCR controller’s position, use a piece of vinyl tape to temporarily attach the VCR controller to the spot where you think the sensor is located. Then see Selecting a VCR Type on the next page to see if the VCR Controller is positioned correctly.

VCR

– R –

– L –

AUDIO

VIDEO

S-VIDEO

GROUND

IN FROM ANT

OUT TO TV

LOW SPEED

DIGITAL

DATA

AUDIO

SATELLITE IN

Connect the VCR Controller

To use the One-Touch Record and Record Timer features, you need to attach the VCR Controller cable to the VCR and the satellite receiver.

1. Plug the VCR Controller into the VCR jack on the satellite receiver.

2. Affix the other end in front of the remote control sensor on your VCR.

Remonte Control

IR Sensor

Arrow buttons

MENU button

DIRECT

FET

INF

ELE

DIRECTV button

SELECT button

CLEAR button

All on-screen menus can be handled the same way, using highlight and select navigation.

Highlight and select navigation has two steps:

1. Use the arrow buttons (up, down, left, and right) on the remote control to highlight different choices on the screen.

2. Press SELECT to select the highlighted item.

Note: When a highlighted on-screen menu choice has a number beside it, you can also press the corresponding number button on the remote control to select it.

Once you know how to navigate on-screen menus, you can complete the Assisted Setup (see the next step) and explore the menu system.

To display the on-screen menu system, press the remote control’s DIRECTV button, then press the MENU button.

Note: Don’t worry about getting stuck inside a menu. Pressing the CLEAR button on the remote control takes you out of the menu system and back to the program you were watching.

Continues on next page...

Using Highlight and Select

Chapter 1 9

Connections & Setup

Selecting a VCR Type

In order to use the One-Touch Record and Record Timer features, you need to tell the satellite receiver which VCR brand you are using.

1. Tune the TV to its satellite receiver viewing channel (either 03, 04, or the TV’s appropriate input channel depending on your connections).

2. Press MENU on the remote control to display the satellite receiver’s Main menu.

3. Highlight and select number 7, System Setup.

4. Highlight and select number 3, Receiver Options.

5. Highlight and select number 2, Set VCR Type.

6. Highlight and select the name of your VCR manufacturer.

Note: If you do not see your VCR manufacturer’s name, select Other (at the bottom of the list) and enter the appropriate code from the VCR Remote Control code list on pages 14-15.

7. Follow the on-screen instructions to ensure that you are using the correct code (if you need more assistance while in a menu, press the remote control’s INFO button for details).

Note: Some VCR brands may not be capable of being controlled by the receiver.

Complete the Assisted Setup

If you installed your satellite dish antenna yourself, you may have already used the Assisted Setup to find dish-pointing coordinates, acquire and finetune the signal, and run a system test.

If you need to run the setup again, select System Setup from the Main menu, then select Assisted Setup. To check your dish-pointing coordinates or run the signal strength meter, display the Main menu, then select System Setup, and finally Dish Pointing.

Tip

When you order programming, you need to know your access card and receiver ID numbers. To get these numbers, select System Setup from the Main menu, then System Test.

Wait for the system to run all of its tests. The access card and receiver ID numbers are displayed at the end of the system test.

Write the access card and receiver ID numbers in the space below for easy reference:

Important!

If local channels are available in your area and you decide to subscribe, the receiver will need to download all of your program guide information again. This might take a few minutes. See “Wait for the Receiver to Download ADVANCED PROGRAM GUIDE™ Information” on page 8 for more information.

Order Programming

After you have installed your DIRECTV® System, you should contact DIRECTV to order DIRECTV® programming.

With this receiver and the proper satellite dish antenna, you may be able to subscribe to local channels from DIRECTV in certain areas. Additional equipment may be required in some markets. Check with your retailer or visit DIRECTV in your area.

ACTIVATION OF PROGRAMMING MAY BE SUBJECT TO CREDIT APPROVAL AND REQUIRES VALID SERVICE ADDRESS, SOCIAL SECURITY NUMBER AND/OR MAJOR CREDIT CARD. DEPOSIT OR PREPAYMENT MAY BE REQUIRED. Professional and collegiate sports subscriptions sold separately. Eligibility for local channels based on service address within certain designated market areas as defined by Nielsen Media Research, Inc. In some areas served by members or affiliates of the National Rural Telecommunications Cooperative, local channels may be available from DIRECTV rather than the NRTC member or affiliate. Programming, pricing, terms and conditions subject to change. Hardware and programming sold separately. Pricing is residential. Taxes not included. Equipment specifications and programming options may vary in Alaska and Hawaii. DIRECTV services not provided outside the U.S. DIRECTV programming is sold separately and independently of DIRECTV System hardware. A valid programming subscription is required to operate DIRECTV System hardware. Receipt of DIRECTV programming is subject to the terms of the DIRECTV Customer Agreement; a copy is provided at DIRECTV.com and in your first bill. Activate your DIRECTV 800-347-3288).

DIRECTV.com for information on availability of local channels from

programming today at 1-800-DIRECTV (1-

10 Chapter 1

STOPPAUSE

ON OFF

AUX2

ACK

SKIP

MUTE

CLEAR

GUIDE

WHO INPUT

AUX1

VOL

CH -

(-)

Remote Control Buttons

VCR When programmed, tells the remote to

control the VCR. This button lights up when you

press a valid button in VCR mode (see Modes of

Operation on page 13 for more details).

AUX1 Turns on a second RCA satellite receiver.

AUX1 can also be programmed to control an

auxiliary component. This button lights up when

you press a valid button in AUX1 mode (see Modes

of Operation on page 13 for more details).

DVD When programmed, tells the remote to

operate the DVD player. This button lights up when

you press a valid button in DVD mode (see Modes

of Operation on page 13 for more details).

MUTE When programmed to control a TV or

audio receiver, this button reduces that

component’s volume to its minimum level. Press

CH + and CH - Use to scan up and down

through the channels in the current channel list.

In the program guide or menu system, use the CH

buttons to page up and down a screen at a time.

FETCH In the program guides, displays the guide

toolbar at the bottom of the screen. During

normal viewing, displays the Fetch menu with up

to eight different actions, or executes a single

task- depending on the preferences set.

GUIDE Brings up the program guide. Subsequent

presses of the GUIDE button switch between the

SELECT/i (interactive) Selects a highlighted

choice if you are in the menu system. Also brings

up the password challenge and purchase offer

Press the SELECT button when the DIRECTV

INTERACTIVE

™

programs and commercials. Pressing SELECT

displays more information and offers the chance

to interact with what is displayed on screen.

MENU Displays the Main menu. When using the

remote control to operate other components, the

MENU button might also bring up that

WHO•INPUT Press one or more times to scroll

through the user profiles. When using the remote

control to operate an RCA, GE, or PROSCAN TV (in

TV mode), press the WHO•INPUT button one or

more times to scroll through the available video

again to restore the volume.

Detail and Grid guide formats.

screens outside of the menu system.

icon ( ) appears during interactive

component’s menu system.

input sources.

Chapter 2: Using the Remote Control

ON•OFF Turns the component you are

controlling on or off. When pressed twice

within two seconds, all components that

are on are turned off (this feature only works with most RCA, GE, and Proscan

products). The component keys also light

up, one after another, counterclockwise in

a circle.

DIRECT

FET

INF

NTENN

Transport Buttons (REVERSE, PLAY, FORWARD, RECORD, STOP, PAUSE) In onscreen guides, PLAY advance the display one page, FORWARD advances the display 6 hours and REVERSE moves time backward 6 hours. When the remote control is programmed, these buttons also control an auxiliary component, such as a VCR or DVD player (when the remote is in the correct mode). If the VCR Controller is connected, pressing the RECORD button schedules a timer recording from the Program Guide or begins recording while watching a program (in VCR mode).

TV When programmed, tells the remote to control the TV. This button lights up when you press a valid button in TV mode (see Modes of Operation on page 13 for more details).

AUX2 Turns on a compatible RCA amplifier/ audio receiver. AUX2 can be programmed to control an auxiliary component. This button lights up when you press a valid button in AUX2 mode (see Modes of Operation on page 13 for more details).

DIRECTV Tells the remote to control the digital satellite receiver. This button lights up when you press a valid button in DIRECTV mode (see Modes of Operation on page 13 for more details).

SKIP Activates the commercial skip mode on some RCA, GE, and Proscan products that offer Commercial Skip feature. See the user’s manual that came with your TV for more information. Activates the search function on some RCA, GE, or ProScan VCRs (when the remote is in VCR mode).

VOL up and down When programmed, adjusts the audio volume of your TV or audio receiver.

GO BACK Moves you back and forth between the last two selected channels. In the menu system, returns you to the previous screen.

INFO Brings up the on-screen channel banner. In the program guides, INFO gets information about the highlighted program or channel. In the menu system, INFO displays context-sensitive help for highlighted control elements.

Arrows Moves the on-screen highlight up, down, left, or right.

CLEAR Removes the on-screen displays and returns you to normal viewing.

Digit Buttons (0 - 9) Tune directly to a specific channel. In the menu system, use 1-9 to select menu items, or use 0 to return to the previous menu screen.

ANTENNA In TV mode, toggles between the satellite and standard TV/cable signals when the satellite receiver is connected to the TV using the OUT TO TV jack. In VCR mode, functions as a TV/ VCR input button.

Note: The component key corresponding to the mode you’re in flashes when the remote batteries are low and you press a button on the remote. A warning banner may also

Chapter 2 11

appear on-screen when you press a remote button and your batteries are low (if you’re watching satellite programming).

Illustrations contained in this document are for representation only.

Using the Remote Control

STOPPAUSE

ON OFF

AUX2

ACK

SKIP

MUTE

CLEAR

GUIDE

WHO INPUT

AUX1

VOL

CH -

(-)

Top of the Digital Satellite Receiver

This diagram illustrates the buttons on the top (also referred to as the front panel) of the digital satellite receiver. For more information on the function of the front panel buttons and many other features of your digital satellite receiver, press the MENU button and select System Setup from the Main menu, then select Receiver Index.

POWER

Front Panel Buttons

POWER Use to turn your digital satellite receiver on for viewing or off when you are not viewing it. Your receiver will still be able to download software upgrades and receive messages from program providers when it is off.

MENU / SELECT Use this button to display the Main menu, password challenge screen or purchase offer screen. If you are already in the menu system, pressing this button selects the highlighted item.

Arrows Use the navigation arrows to move the on-screen highlight up, down, left, or right. INFO Use this button to display the channel banner. Press twice to display additional program information, when available. While in the menu

system INFO also summons context sensitive help about a highlighted menu item.

Component buttons and ON•OFF button

FET

INFO

Programming the Remote Control

The digital satellite receiver’s remote can be programmed to control most brands of remote

DIRECT

INF

controllable components. The remote is already programmed to control most RCA, GE and Proscan components; it may need to be programmed to control other manufacturers’ brands.

Testing the Remote Control

To determine whether the universal remote control needs to be programmed, turn a component on, such as a VCR, point the remote at the VCR, and press the VCR button. Then press the ON•OFF or CH + and CH - buttons to see if the VCR responds to the remote commands. If not, the remote needs to be programmed.

There are two ways to program the remote control: Automatic Code Search or Direct Entry.

PLAY button

NTENN

REVERSE button

STOP button

Note:

The DIRECTV button cannot be programmed.

Using Automatic Code Search

The following instructions can be used to program the remote to control many of the components connected to your TV. If you want to exit the automatic code search without programming any of your components, press the CLEAR button until the component button you’re trying to program turns off.

1. Turn on the component you want to control (VCR, satellite receiver, etc.)

2. Press and hold the button you want to program. While holding the component button, press and hold ON•OFF until all of the component buttons (VCR, TV, DVD, DIRECTV, AUX1 and AUX2) flash. Then, release both buttons.

Note: The AUX1 and AUX2 buttons will only search through the codes for their default type of component during the automatic code search – satellite receivers for AUX1 and audio components for AUX2. If you want to use these buttons for a different type of component – for example, a DVD player for AUX1 – then use direct entry to program these buttons. See the next page for more information.

3. Point the remote at the component, press and release PLAY, then wait five seconds or until the component button you’re trying to program stops flashing.

At this point the remote control is searching for the correct code to program, so keep pointing it at the component. If, after five seconds, the component you want to control does not turn off, press and release PLAY again to tell the remote to search the next set of codes.

Continue pressing and releasing PLAY until the component turns off or until the all of the component buttons on the remote flash 4 times in unison. If the component has not turned off by the time all the component buttons on the remote control flash 4 times in unison, then the remote cannot control that particular component.

If the component you want to control does turn off:

1. Press and release REVERSE, then wait two seconds. Repeat this step until the component turns back on.

2. To finish, press and hold STOP until the component button you’re trying to program on the remote control turns off. This saves the code to that button.

12 Chapter 2

Using the Remote Control

ON OFF

AUX2

AUX1

Important:

This remote may not be compatible with all models of all brands of components. It also may not operate all functions of the remote that came with your component.

Note:

The DIRECTV button cannot be programmed.

Component buttons

DIRECT

Using Direct Entry

1. Turn on the component to be programmed.

2. Look up the brand and code number(s) for the component on the code list at the end of this section.

3. On your remote control, press and hold the component button you want to program.

4. While pressing the component button, enter a code from the code list. If all of the component buttons flash 4 times in unison, then the code you’ve entered is not the right kind of code for that button (see pages 14 and 15 to see which buttons can be programmed to control the component you want).

5. Release the component button, point the remote at the component and then press ON•OFF to see if the component responds to the remote control commands. If it doesn’t, try pressing the component button and then ON•OFF (or other buttons on the remote) again.

6. If you get no response, repeat these steps using the next code listed for your brand, until the component responds to the remote control commands.

Operating Other Components

Once the remote has been programmed successfully, you are ready to use it to operate your components.

To Operate the Component:

1. Press the component button (TV, VCR, DVD, DIRECTV, AUX1, or AUX2) to set the remote to control the component.

2. Press ON•OFF to turn the component on or off.

3. Use the remote control buttons that apply to that component. The component button on your remote lights up when you press valid buttons while in that component’s mode.

Note: Your remote’s buttons might operate differently for other components, especially when you’re using another component’s menu system.

Tip:

If something unexpected happens (or if nothing happens) when you press a remote control button, check which component button lights up when you press that button. If the wrong component button lights up, press the component button the corresponds to the component you want to control – this puts the remote control in the right mode. Now that the remote is in the correct mode, press the button you were pressing before.

One Button Recording

If your remote is programmed to operate a VCR, and the VCR is properly connected to the satellite receiver, you only need to press the RECORD button to begin recording from video.

Modes of Operation

Because this universal remote can control several different components (DVD player, VCR, cable box, etc.) it uses operational modes triggered by the component buttons. For example, if you want the remote control to operate the TV, press the TV button to put the remote into TV mode. If you want the remote to operate the VCR, press the VCR button.

The button corresponding to the mode the remote is in lights up when you press any button that works in that mode. For example, if you’re in TV mode and you press the VOL+ button, the TV button lights up. This tells you that the command to increase the volume is being sent to the TV (and not the satellite receiver, for example).

Controlling a Second RCA Satellite Receiver

The remote can control two RCA satellite receivers. From the Main menu, select System Setup, then Receiver Options, then Remote Setup. Then follow the on-screen instructions. By default, the DIRECTV button is used to control the first RCA satellite receiver and the AUX1 button is used to control the second RCA satellite receiver.

If your second receiver is an RCA, GE, or Proscan and you want to control it using the AUX1 button, use code 5001. Code 5000 is used by the DIRECTV button.

If you want to control a second non-RCA satellite receiver, use the AUX1 or AUX2 buttons. See the Using Automatic Code Search section on the previous page for more information.

Chapter 2 13

+ 33 hidden pages