Radio Shack 900 MHz Digital Spread Spectrum Dual Keypad Cordless Telephone with Caller ID/Call Waiting ID, Sprint 43-5520 Owner's Manual
Page 1
Owner’s Manual
Please read before using this equipment.
900 MHz Digital Spread
Spectrum Dual Keypad
Cordless Telephone
with Caller ID/Call Waiting ID
43-5520.fm Page 1 Friday, July 21, 2000 8:01 AM
Page 2
2
ˆ
Contents
Features .................................................................................................................................. 6
Installation .............................................................................................................................. 7
Mounting the Phone .......................................................................................................... 7
Connecting, Charging, and Replacing the Battery Pack ................................................... 9
A Quick Look at the Handset .......................................................................................... 11
Setting the Dialing Mode ................................................................................................. 11
Setting the Ringer Tone/Volume ...................................................................................... 12
Turning Auto Talk On/Off ................................................................................................. 12
Turning Caller ID/Call Waiting On/Off ............................................................................. 12
Storing Your Area Code .................................................................................................. 13
Operation .............................................................................................................................. 13
Making and Receiving Calls ............................................................................................ 13
Using the Speakerphone ................................................................................................. 14
Using Hold ....................................................................................................................... 14
Using Mute ...................................................................................................................... 14
Using Redial .................................................................................................................... 14
Using Flash ..................................................... ... ... .......................................................... 15
Using Tone Services on a Pulse Line .............................................................................. 15
Using Page/Intercom ......................... .............................................................................. 15
Memory Dialing .......................................................... ... .................................................. 16
Using a Headset ....................................................................... ....................................... 18
Caller ID Operation ......................................................................................................... 19
Using the Phone Company’s Network Service ............................................................... 21
Troubleshooting ................................................................................................................... 22
Care ................................................................................................................................ 23
WARNING:
To reduce the risk of fire or
shock hazard, do not expose this product to rain
or moisture.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
CAUTION:
TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED PERSONNEL.
!
This symbol is intended to alert
you to the presence of uninsulated dangerous voltage within
the product’s enclosure that might
be of sufficient magnitude to constitute a risk of electric shock. Do
not open the product’s case.
This symbol is intended to inform
you that important operating and
maintenance instructions are
included in the literature accompanying this product.
!
RadioShack and RadioShack.com are trademarks used by RadioShack Corporation.
The Sprint Logo is a registered trademark of Sprint Communications Company L.P. Used under license.
43-5520.fm Page 2 Friday, July 21, 2000 8:01 AM
Page 3
3
This phone has been tested and found to
comply with all applicable UL and FCC standards.
IMPORTANT CALLER ID
INFORMATION
To use the phone's Caller ID and Call W aiting with Caller ID features, you must be in an
area where those services are available and
you must subscribe to those services
through your local phone company. Where
Caller ID is offered, one or more options are
generally available:
• caller's number only
• caller's name only
• caller's name and number.
READ THIS BEFORE
INSTALLATION
We have designed your phone to conform to
federal regulations, and you can connect it to
most telephone lines. However, each phone
(and each device, such as a telephone or answering machine) that you connect to the
telephone line draws power from the telephone line. We refer to this power draw as
the device's ringer equivalence number, or
REN. The REN is on the bottom of your
phone.
If you use more than one phone or other device on the line, add up all of the RENs. If the
total is more than five (or three in rural areas), your telephones might not ring. If ringer
operation is impaired, remove a device from
the line.
Your phone complies with Part 68 of
FCC
Rules
. You must, upon request, provide the
FCC registration number and the REN to
your telephone company. Both numbers are
on the bottom of your phone.
Note:
You must not connect your phone to:
• coin-operated systems
• party-line systems
• most electronic key telephone systems
Important:
• Cordless phones such as this one
require AC power to operate. When the
AC power is off, you cannot dial out or
receive incoming calls using your
phone. For this reason, the phone
should not be your only telephone. To be
safe, you should also have a phone that
does not require AC power to operate
(not a cordless phone) so you can still
make and receive calls if there is an AC
power failure.
• Some cordless phones operate at frequencies that might cause interference
to nearby TVs and VCRs. To minimize
or prevent such interference, the base of
the cordless phone should not be placed
near or on top of a TV or VCR.
• Your cordless pho ne operates on standard radio frequencies, as allocated by
the FCC. Even though your phone's
access protection code prevents unauthorized use of your phone line, it is possible for other radio units operating on
similar frequencies within a certain area
to unintentionally intercept your conversations and/or cause interference. This
possible lack of privacy can occur with
any cordless phone.
THE FCC WANTS YOU TO
KNOW
In the unlikely event that your phone causes
problems on the phone line, the phone company can temporarily discontinue your service. If this happens, the phone company
attempts to notify you in advance. If advance
43-5520.fm Page 3 Friday, July 21, 2000 8:01 AM
Page 4
4
notice is not practical, the phone company
notifies you as soon as possible and advises
you of your right to file a complaint with the
FCC.
Also, the phone company can make changes
to its lines, equipment, operations, or procedures that could affect the operation of this
telephone. The telephone company notifies
you of these changes in advance, so you can
take the necessary steps to prevent interruption of your telephone service.
LIGHTNING
Your telephone has built-in protection circuits
to reduce the risk of damage from surges in
telephone line and power line current. These
protection circuits meet or exceed the FCC
requirements. However, lightning striking the
telephone or power lines can damage yo ur
telephone.
Lightning damage is not common. Nevertheless, if you live in an area that has severe
electrical storms, we suggest that you unplug
your phone when storms approach to reduce
the possibility of damage.
FCC STATEMENT
The phone complies with the limits for a
Class B digital device as specified in Part 15
of
FCC Rules
. These limits provide reasonable protection against radio and TV interference in a residential area. However, your
equipment might cause TV or radio interference even when it is operating properly. To
eliminate interference, you can try one or
more of the following corrective measures:
• Reorient or relocate the receiving
antenna.
• Increase the distance between the
equipment and the radio or TV.
• Use outlets on different electrical circuits
for the equipment and the radio or TV.
Consult your local RadioShack store if the
problem still exists.
IMPORTANT SAFETY
INSTRUCTIONS
When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock
and injury to persons, including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions
marked on the product.
3. Never install telephone wiring during a
lightning storm.
4. Never install telephone jacks in wet
locations unless the jack is specifically
designed for wet locations.
5. Never touch uninsulated telephone
wires or terminals unless the telephone
line has been disconnected at the network interface.
6. Use caution when installing or modifying
telephone lines.
7. Do not fix the AC power supply cord to
building surfaces with metal fittings (if
the product has an AC power cord).
8. Unplug this product from the wall outlet
before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp
cloth for cleaning.
9. Do not use this product near water, for
example, near a bath tub, wash bowl,
kitchen sink, or laundry tub, in a wet
basement, or near a swimming pool.
10. Do not place this product on an unstable
cart, stand, or table. The product may
fall, causing serious damage to the
product.
43-5520.fm Page 4 Friday, July 21, 2000 8:01 AM
Page 5
5
11. Slots and openings in the cabinet and
the back or bottom are provided for ventilation. To protect it from overheating,
these openings must not be blocked or
covered. The openings should never be
blocked by placing the product on a bed,
sofa, rug, or other similar surface. This
product should never be placed near or
over a radiator or heat register. This
product should not be placed in a built-in
installation unless proper ventilation is
provided.
12. This product should be operated only
from the type of power source indicated
on the marking label. If you are not sure
of the type of power supply to your
home, consult your local power company.
13. Do not allow anything to rest on the
power cord. Do not locate this product
where the cord will be stepped on.
14. Do not overload wall outlets and extension cords as this can result in a risk of
fire or electric shock.
15. Never push objects of any kind into this
product through cabinet slots as they
may touch dangerous voltage points or
short out parts that could result in a risk
of fire or electric shock. Never spill liquid
of any kind on the product.
16. To reduce the risk of electric shock, do
not disassemble this product. Take it to
a qualified serviceman when service or
repair work is required. Opening or
removing covers may expose you to
dangerous voltage or other risks. Incorrect reassembly can cause electric
shock when the product is subsequently
used.
17. Unplug this product from the wall outlet
and refer servicing to qualified service
personnel under the following conditions:
• When the power cord plug is damaged
or frayed.
• If liquid has been spilled into the product.
• If the product has been exposed to rain
or water.
• If the product does not operate normally
by following the operating instructions.
Adjust only those controls that are covered by the operating instructions
because improper adjustment of other
controls may result in damage and will
often require extensive work by a qualified technician to restore the product to
normal operation.
• If the product has been dropped or the
cabinet has been damaged.
• If the product exhibits a distinct change
in performance.
18. Avoid using a telephone (other than a
cordless type) during an electrical storm.
There may be a remote risk of electric
shock from lightning.
19. Do not use the telephone to report a gas
leak in the vicinity of the leak.
BATTERY SAFETY
INSTRUCTIONS
CAUTION:
TO REDUCE THE RISK OF
FIRE OR INJURY, READ AND FOLLOW
THESE INSTRUCTIONS
.
1. Use only the appropriate type and size
of battery pack specified in the instruction manual provided for this product.
2. Do not dispose of the battery pack in a
fire. The cell may explode. Check with
local codes for possible special disposal
instructions.
43-5520.fm Page 5 Friday, July 21, 2000 8:01 AM
Page 6
6
Features
3. Do not open or mutilate the battery
pack. Released electrolyte is corrosive
and may cause damage to the eyes or
skin. It may be toxic if swallowed.
4. Exercise care in handling the battery
pack in order not to short it with conducting materials such as rings, bracelets,
and keys. The battery or conductor may
overheat and cause burns.
5. Charge the battery pack provided with or
identified for use with this product only in
accordance with the instructions and
limitations specified in the instruction
manual provided for this product.
6. Observe proper polarity orientation
between the battery pack and battery
charger.
SAVE THESE
INSTRUCTIONS
ˆ
Features
Your Sprint 900 MHz Digital Spread Spectrum Dual Keypad Cordless Telephone uses
the most advanced cordless telephone technology to give you superior audio quality and
extended range.
The phone’s Caller ID records each caller’s
telephone number (and name, if available in
your area) and the date and time of the call,
as provided by your local phone company to
Caller ID service subscribers. And, if you
subscribe to Call Waiting with Caller ID, the
phone shows you the incoming caller information, even when you are already on the
phone.
Your phone has these features:
900 MHz Operation
— provides longer
range and less interference than many other
cordless phones.
Spread Spectrum Technology
— spreads
the signal across several frequencies, for
added security during your phone conversations.
Caller ID Memory
— stores up to 50 Caller
ID records.
Dual Keypads
— a full set of keys on both
the handset and base let you use either keypad to operate the phone.
Speakerphone
— lets you make or answer
calls without using the handset.
Lighted Handset Keypad
— Lights when
you press any key or receive a call, making
the phone easy to use, even in total darkness.
Network Service
— supports the advanced
calling features such as Return Call, Repeat
Dial, and Cancel Call Waiting.
3-Line Liquid Crystal Display with Backlight
— lets you view an entire Caller ID
record on one screen.
30-Number Memory Dialing
— lets you
store up to 30 numbers (20 in the handset
and 10 in the base) in memory for easy dialing.
Two-Way Intercom/Paging System
— lets
you send a signal from the base to the handset (or from the handset to the base) to page
someone or locate the handset when it is
away from the base. If someone answers,
you can use the phone as an intercom.
43-5520.fm Page 6 Friday, July 21, 2000 8:01 AM
Page 7
7
Installation
Headset Jack
— lets you connect an optional headset (available from your local RadioShack store) for hands-free convenience.
Facedown or Faceup Handset Charging
— you can place the handset on the base
face down or face up (to show the Caller ID
display, for example).
Volume Control
— lets you adjust the vol-
ume you hear through the handset.
Adjustable Ringers
— you can set different
volumes for the handset and base ringers.
Auto Talk
— lets you set the handset so you
can answer a call by simply lifting the handset from the base or by pressing any key
when the handset is away from the base.
Ample Talk and Standby Time
— the supplied battery (when fully charged) provides
about 7 hours of talk time or 7 days of standby time.
20 Channels
— automatically selects a clear
channel when you make or answer a call.
Security Access-Protection Code
— automatically prevents other cordless phone users from using your phone line.
Redial
— lets you quickly redial any of the
three last numbers dialed on the handset
and the last number dialed on the base.
Flash
— sends an electronic switchhook signal for use with special phone services, such
as Call Waiting.
Tone/Pulse Dialing
— lets you use your
phone with either type of service and you can
quickly switch from pulse to tone dialing for
long-distance, bank-by-phone, or other special services.
Hearing-Aid Compatibility
— lets you use
your phone with hearing aids that have a T
(telephone) switch.
ˆ
Installation
MOUNTING THE PHONE
You can place the phone’s base on a desk or
table, mount it on a standard wall plate or directly on a wall. Choose a location that is:
• near an AC outlet
• near a modular telephone line jack
• out of the way of normal activities
• away from electrical machinery, electrical appliances, metal walls or filing cabinets, wireless intercoms, alarms, and
room monitors
• away from other cordless phones
The base’s location affects the phone’s
range. If you have a choice of several locations, try each to see which provides the best
performance.
Cautions:
You must use a Class 2 power
source that supplies 9V DC
and delivers at least 350 mA.
Its center tip must be set to positive and
its plug must fit the phone's
DC IN 9V
jack. The supplied adapter meets these
specifications. Using an adapter that
does not meet these specifications
could damage the phone or the adapter.
!
43-5520.fm Page 7 Friday, July 21, 2000 8:01 AM
Page 8
8
Installation
• Always connect the AC adapter to the
phone before you connect it to AC
power. When you finish, disconnect the
adapter from AC power before you disconnect it from the phone.
Note:
Your telephone connects directly to a
modular telephone line jack. If your phone
line jack is not a modular jack, you can update the wiring yourself, using jacks and
adapters available at your local RadioShack
store. Or, you can let the phone company update the wiring for you.
The USOC number of the jack to be installed
is RJ11C (RJ11W for a wall plate).
On a Desk Top, Shelf, or Table
1. Plug one end of the supplied long modular cord into the
TEL LINE
jack on the
back of the base.
2. Plug the modular cord’s other end into a
modular telephone line jack.
3. Insert the supplied AC adapter’s barrel
plug into the
DC IN 9V
jack on the back
of the base.
4. Route the adapter’s cord through the
strain relief slot on the bottom of the
base.
5. Plug the adapter into a standard AC outlet.
6. Lift the base’s antenna to a vertical position.
On a Wall Plate or Wall
1. Insert the two tabs at the top of the narrow end of the supplied bracket into the
base’s upper tab slots, then press down
on the bracket’s latches and insert them
into the lower slots.
2. Plug one end of the supplied short modular cord into the
TEL LINE
jack on the
back of the base.
3. Insert the supplied AC adapter’s barrel
plug into the
DC IN 9V
jack.
4. Route the adapter and modular cords
through the grooves on the bracket.
5. Plug the modular cord’s other end into
the wall plate jack, then align the
bracket’s keyhole slots with the wall
plate studs and slide the phone downward to secure it.
6. Plug the adapter into a standard AC outlet.
7. Press and lift out the handset holder.
Rotate it 180°, then snap it back into
place so it holds the handset.
8. Lift the base’s antenna to a vertical position.
43-5520.fm Page 8 Friday, July 21, 2000 8:01 AM
Page 9
9
Installation
Note:
To mount the phone directly on a wall,
you need two screws (not supplied) with
heads that fit into the keyhole slots on the
bottom of the base.
Follow the steps under “On a Wall Plate or
Wall” on Page 8 , then apply these additional
instructions.
1. Drill two holes 3
15
/16 inches
(100 mm) apart. Then thread
a screw into each hole, letting the heads extend about
3
/16 inch (5 mm) from the
wall.
2. Plug one end of the supplied long modular cord into the
TEL LINE
jack on the
back of the base and route the adapter
cable and modular cords through the
grooves on the bracket.
3. Align the bracket’s keyhole slots with the
mounting screws and slide the phone
downward to secure it.
CONNECTING, CHARGING,
AND REPLACING THE
BATTERY PACK
The phone comes with a rechargeable
nickel-cadmium battery pack in the handset. Before using your phone, you must
connect the battery pack, then charge it for
about 24 hours.
1. Press down and slide off the battery
pack compartment cover.
2. Lift the battery pack out of the compartment.
3. Plug the battery pack's connector into
the socket in the compartment, (the connector fits only one way), replace the
battery pack, and replace the cover.
To charge the battery pack, place the handset either faceup or facedown on the base.
The CHARGE/IN USE indicator on the base
lights and
Total:00
appears.
Recharge the battery pack when
Low Bat-
tery
flashes.
Important:
Be sure the battery pack is properly connected before you try to charge it.
The CHARGE/IN USE indicator lights when
the handset is on the base, even if the battery pack is not connected.
Notes:
• When you first use the phone after
charging or recharging the battery pack,
the phone might not work and you might
hear a beep when you press
TALK
.
Return the handset to the base for about
5 seconds to reset the security accessprotection code.
• If the base loses power for 60 minutes
while the handset is away from it or the
handset’s battery pack is completely discharged, the security access-protection
code might be lost. To reset the code,
315/16"
3
/16"
43-5520.fm Page 9 Friday, July 21, 2000 8:01 AM
Page 10
10
Installation
return the handset to the base for about
5 seconds.
• Using a pencil eraser, clean the charging contacts on the handset and base
about once a month.
• If the battery pack becomes weak during
a call, the handset beeps every 3 seconds and
Low Battery
flashes. When
this happens, you cannot make another
call on the phone until you recharge the
battery pack.
• About once a month, fully discharge the
battery by keeping the handset off the
base until
Low Battery
flashes. Otherwise, the battery pack loses its ability
to fully recharge.
• If the display is blank and the phone
does not work, recharge the battery
pack. (The battery power might be too
low to light the display.)
• If you are not going to use your phone
for an extended period of time, disconnect the battery pack. This increases the
battery pack's usable life.
The supplied battery pack should last about
a year. If the battery pack does not hold a
charge for more than 2 hours after an overnight charge, replace it with a new 3.6-volt,
600 mAh battery pack with a connector that
fits the socket in the battery compartment.
You can order a replacement battery pack
through your local RadioShack store. Install
the new battery pack and charge it for about
24 hours.
Warning:
Dispose of the old battery pack
promptly and properly. Do not burn or bury it
(see “Battery Safety Instructions” on Page 5
for additional information on proper battery
handling).
If you have trouble replacing the battery
pack, take the phone to your local RadioShack store for assistance.
Important:
The EPA certified
RBRC
®
Battery Recycling Seal
on the nickel-cadmium (Ni-Cd)
battery indicates RadioShack
is voluntarily participating in an
industry program to collect and recycle these
batteries at the end of their useful life, when
taken out of service in the United States or
Canada. The RBRC program provides a convenient alternative to placing used Ni-Cd batteries into the trash or the municipal waste
stream, which may be illegal in your area.
Please call 1-800-THE-SHACK (1-800-843-
7422) for information on Ni-Cd battery recycling and disposal bans/restrictions in your
area. RadioShack’s involvement in this program is part of the company’s commitment to
preserving our environment and conserving
our natural resources.
43-5520.fm Page 10 Friday, July 21, 2000 8:01 AM
Page 11
11
Installation
A QUICK LOOK AT THE HANDSET
Note:
The handset window has a plastic film on it to protect it during shipment. Carefully pee l
off the film before using your phone for the first time.
SETTING THE
DIALING MODE
Set
DIAL MODE
on the back of the base for
the type of service you have. If you are not
sure which type you have, once the battery
pack is fully charged, do this test.
1. Be sure
DIAL MODE
is set to T (tone).
2. Lift the handset, press
TALK
, and listen
for a dial tone.
3. Press any number except 0.
Note:
If your phone system requires that
you dial an access code (9, for example)
before you dial an outside number, do
Press INTCM to page someone at
the base or transfer a call to the
base (see “Using Page/Intercom” on
Page 15).
Use TALK to make a
call (see “Making and
Receiving Calls” on
Page 13).
Use CALL ID to review
the Caller ID records.
Use MEM to store or recall
names and numbers in memory
(see “Memory Dialing” on
Page 16).
Press DEL to Delete Caller ID
records (see “Deleti ng Caller
ID Records” on Page 20) or to
erase information if you make
a mistake.
Press VOL/CID
8888
or
9999
to adjust
the handset volume (see “Adjusting
the Handset Volume” on Page 13),
set the ringer tone/volume (see
“Setting the Ringer Tone/Volume”
on Page 12), view Caller ID records
(see “Caller ID Operation” on
Page 19), or select options.
Press SELECT/CHANNEL to
select the phone’s channels
(see “Selecting the Channel”
on Page 13) and other options.
Press RDL/PAUSE to select a phone
number so you can redial it (see
“Using Redial” on Page 14) or store
a pause in a number (see “Entering
a Pause” on Page 18).
Press FLASH to use
the phone’s flash
function (see “Using
Flash” on Page 15).
Press
*
TONE
6666
to use your phone
company’s special tone services on
a pulse line (see “Using Tone Services on a Pulse Line” on Page 15).
Press MENU to use the telephone
company’s network service (see
“Using the Phone Company’s Network Service” on Page 21).
43-5520.fm Page 11 Friday, July 21, 2000 8:01 AM
Page 12
12
Installation
not press the access code number
either.
If the dial tone stops
, you have touch-
tone service. Leave
DIAL MODE
set to T.
If the dial tone continues
, you have
pulse service. Set
DIAL MODE
to
P
(pulse).
SETTING THE RINGER
TONE/VOLUME
You can select one of four different ringer
tone/volume settings on the handset. Repeatedly press
VOL/CID
8888
or
9999
(except
during a call) to select the desired ringer setting. Each time you press a button, the
phone rings at the selected setting and the
display shows
Ringer A High, Ringer A
Low
,
Ringer B High
, or
Ringer B Low
.
Note:
Pressing
VOL/CID
8888
when the phone
is set to
Ringer A High
or
VOL/CID
9999
when the phone is set to
Ringer B Low
does not change the setting. Press the opposite arrow key to change the setting.
To set the base’s ringer volume, set
RING
VOL
on the back of the base to
OFF, LO
, or
HI
.
Notes:
• When you set
RING VOL
to
OFF
, the
base (and the handset if it is on the
base) does not ring but another phone
connected to the same line rings. If the
handset is away from the base, the
handset also rings.
• When you set the auto talk function to
off, the handset rings when you lift the
handset from the base. See “Turning
Auto Talk On/Off.”
TURNING AUTO
TALK ON/OFF
Your phone is preset so you must press
TAL K
when you lift the handset from the base
to answer a call. With auto talk turned on,
you can answer a call by just lifting the handset from the base. If the handset is away
from the base, you can answer by pressing
any key.
Follow these steps to turn auto talk on or off.
1. Lift the handset and hold down
CALL ID
.
A menu appears with
Auto Talk
selected.
2. Press
SELECT/CHANNEL
to change the
auto talk setting. On or
Off
appears
indicating the selected setting.
3. Return the handset to the base or press
CALL ID
to store the new setting.
TURNING CALLER ID/
CALL WAITING ON/OFF
If you subscribe to Call Waiting with Caller ID
service, you can set the phone to show Caller ID information for an incoming call even
while you are using the phone.
Follow these steps to turn the Caller ID/Call
Waiting feature on or off.
1. Lift the handset and hold down
CALL ID
.
2. Press 2 or
VOL/CID
9999
to select
CIDCW
(Caller ID/Call Waiting).
3. Press
SELECT/CHANNEL
to change the
Caller ID/Call Waiting setting. On or
Off
appears indicating the selected
setting.
Return the handset to the base to store the
new setting.
43-5520.fm Page 12 Friday, July 21, 2000 8:01 AM
Page 13
13
Operation
STORING YOUR
AREA CODE
You can store your local area code in the
phone’s Caller ID record so it does not show
the area code if the received call is from your
local area. If for some reason you need to
dial the area code (or store it in the memory),
you can add it afterwards. See “Adding/Deleting the Area Code” on Page 20.
Note:
If your calling area requires 10-digit dialing including area code, do not enter the
area code but leave this option blank.
Follow these steps to store your area code.
1. Lift the handset and hold down
CALL ID
.
2. Press
3
or
VOL/CID
9999
twice to select
Area Code
.
3. Press
SELECT/CHANNEL
, then enter
your three-digit area code. If you make a
mistake, repeatedly press
6666
or
7777
to
move the cursor over the incorrect digit,
then enter the correct number.
Note:
If an area code is already stored, it ap-
pears. To delete the area code, press
DEL
three times. Then enter your area code. Or
you can use
6666
or
7777
to move the cursor and
edit the area code.
Press
SELECT/CHANNEL
to store the area
code, then press
CALL ID
or return the hand-
set to the base to clear the display.
ˆ
Operation
MAKING AND RECEIVING
CALLS
To make a call, lift the handset and press
TAL K
.
Talk
and the current volume setting
(see “Adjusting the Handset Volume”) appear on the handset’s display, and the
CHARGE/IN USE indicator on the base
lights. Then dial the number. The number appears on the handset as you dial, then the
call’s elapsed time appears.
You can also dial the number before you
press
TAL K
.
If you make a mistake, press
DEL
until the incorrect entry is erased, then enter the correct
number. To delete the entire number, hold
down
DEL
for at least 1 second.
When you receive a call,
Incoming Call
appears. To answer it, lift the handset from
the base and press
TALK
. If auto talk is on,
just lift the handset from the base or press
any key.
Talk
and the current volume set-
ting appear.
To end a call, place the handset on the base
or press
TALK
.
Selecting the Channel
The phone has 20 channels. If the call
seems to disconnect for no reason during a
call, press
SELECT/CHANNEL
on the handset
to select a different channel.
Scanning
appears while your phone searches for a clear
channel.
Adjusting the Handset Volume
To adjust the handset’s volume during a call,
press
VOL/CID
8888
or
9999
until you reach the
desired volume level.
Volume Maximum
,
Volume High, Volume Medium
, or
Volume Low
appears.
43-5520.fm Page 13 Friday, July 21, 2000 8:01 AM
Page 14
14
Operation
Once you set the volume level, the setting is
maintained even after you hang up the
phone.
Note:
When you press
VOL/CID
8888
while the
volume is maximum or
VOL/CID
9999
while the
volume is low, the setting does not change
and the phone beeps three times.
USING THE
SPEAKERPHONE
To make or answer a call using the speakerphone, press
SPEAKER
. The SPEAKER indicator lights. When you hear a dial tone, dial
the number.
To set the speakerphone’s volume, slide
VOLUME
on the right side of the base.
To end a speakerphone call, press
SPEAKER
again.
Switching Between the Handset
and Speakerphone
To switch to the speakerphone while you are
using the handset, press
SPEAKER
on the
base. When you hear the conversation or
dial tone on the speakerphone, press
TAL K
on the handset.
To switch to the handset while you are using
the speakerphone, simply lift the handset off
the base. If the handset is away from the
base, press
TALK
, then press
SPEAKER
.
Using Both the Handset
and Speakerphone
If someone else is using the speakerphone,
press
TALK
on the handset to join the con-
versation.
If someone else is using the handset, press
SPEAKER
on the base to join the conversa-
tion.
During the call, one person can hang up and
another person can continue the call at the
other keypad. Or, both people can hang up
at the same time to end the call.
Note:
If you hear a high-pitched noise from
the base’s speaker, the handset and the
base are too close together.
USING HOLD
Press
HOLD
to put a speakerphone call on
hold. The HOLD indicator lights. While a call
is on hold, you can make an intercom call
(see “Using Page/Intercom” on Page 15) between the handset and the base without disconnecting the call.
To release a call from hold, lift the handset
and press
TALK
, press
SPEAKER
or
HOLD
on
the base, or pick up any extension phone on
the same line.
USING MUTE
While talking on the speakerphone, you can
temporarily turn off the phone’s microphone
by pressing
MUTE
so the other party cannot
hear you. The SPEAKER indicator flashes.
Press
MUTE
or
SPEAKER
to resume your
conversation.
Note:
If the phone is close to loud noises
while you are using the speakerphone, the
phone might not switch to let you hear the
person on the other end of the line. If this
happens, press
MUTE
to turn off the micro-
phone so you can hear the caller. Press
MUTE
again to speak.
USING REDIAL
You can quickly dial any of the last three
numbers you dialed recently on the handset.
Lift the handset and repeatedly press
RDL/
PAUSE
until the number you want to dial dis-
43-5520.fm Page 14 Friday, July 21, 2000 8:01 AM
Page 15
15
Operation
plays. Then press
TALK
and the phone dials
the number.
To dial the last number dialed using the
base, press
SPEAKER
then
REDIAL
.
Notes:
• The redial memory for each keypad is
separate. You cannot redial a number
you dialed on the handset’s keypad
using
REDIAL
on the base’s keypad, and
vice versa.
• On the handset, you can also press
RDL/PAUSE
after pressing
TAL K
to dial
the last number dialed.
• The redial memory holds up to 32 digits,
so you can redial long-distance as well
as local numbers.
• The redial memory also holds pause
entries. See “Entering a Pause” on
Page 18.
USING FLASH
FLASH
performs the electronic equivalent of
a switchhook operation for special services,
such as Call Waiting.
For example, if you have Call Waiting, press
FLASH
to answer an incoming call without
disconnecting the current call. Press
FLASH
again to return to the first call.
Note:
If you do not have any special phone
services, pressing
FLASH
might disconnect
the current call.
USING TONE SERVICES
ON A PULSE LINE
Some special services, such as bank-byphone, require tone signals. If you have
pulse service, you can still use these special
tone services by following these steps.
1. Be sure
DIAL MODE
is set to P.
2. Dial the service’s main number.
3. When the service answers, press
*
/
TONE/
6666
on the handset (
TONE
on the
base). Any additional numbers you dial
are sent as tone signals.
When you hang up, the phone automatically
resets to pulse dialing.
USING PAGE/INTERCOM
You can use the phone as a two-way pager
and intercom between the base and the
handset. This is useful if the handset is away
from the base and you want to locate it, or if
you want to converse with someone through
the intercom.
To page the base from the handset, press
IN-
TCM
.
Paging Base
appears, and the base
and handset ring. Press
SPEAKER
or
INTCM/
PAGE
on the base to answer the page.
In-
tercom
appears.
To page the handset from the base, press
IN-
TCM/PAGE
. The handset and base ring, and
Paging
appears. Press
TALK
or
INTCM
on
the handset to answer the page.
Intercom
appears.
To end an intercom call, press
TALK
on the
handset, press
SPEAKER
on the base, or
hang up the handset.
If a call comes in during an intercom conver-
sation, either the person at the base or the
person at the handset can answer the call.
Press
TALK
on the handset or
SPEAKER
on
the base once to end the intercom call, then
press
TALK
or
SPEAKER
again to answer the
incoming call.
Note:
You can use the intercom while a call
is on hold, but not during a conversation.
43-5520.fm Page 15 Friday, July 21, 2000 8:01 AM
Page 16
16
Operation
Transferring a Call Between the
Handset and Base
You can use the phone’s intercom feature to
transfer a call between the handset and the
base.
To transfer a call from the handset to the
base, press
INTCM
. The call is placed on
hold, and
Paging Base
and
Hold
appear.
When the person at the base answers, press
TALK
. The call is released from hold and
transferred to the base. To return to handset
use, press
TALK
or
INTCM
.
To transfer a call from the base to the handset, press
INTCM/PAGE
. The call is placed on
hold, and
Paging
and
Hold
appear. When
the person with the handset answers, press
SPEAKER
. The call is released from hold and
transferred to the handset. To return to the
base use, press
SPEAKER
or
INTCM/PAGE
.
MEMORY DIALING
You can store up to 30 numbers in memory
(20 in the handset’s and 10 in the base’s
memory), then dial a stored number by
pressing a memory location number.
You can also store a name with each number
in the handset’s memory.
Use the supplied memory directory sticker to
record your stored numbers. Peel the backing from the sticker and attach it to the
base’s handset cradle.
Storing a Number in the Handset’s
Memory
Notes:
• The phone beeps five times and exits
the storing process if you wait more than
20 seconds between each keypress.
• If you receive a call during memory
entry, the phone exits the storing process.
Follow these steps to store a number in the
handset’s memory.
1. Lift the handset.
2. Hold down
MEM
until
Memory Store
and a list of memory location numbers
appear.
3. Press a number (
01–20
) or press
VOL/
CID
8888
or
9999
to choose a two-digit memory location. Precede a single digit location number with 0 — 01, 02, 03, and so
on.
4. To store a name, press
SELECT/CHAN-
NEL
.
Store Name
appears.
If you do not want to enter a name, skip
to Step 6.
5. To enter a name , press
VOL/CID
8888
or
9999
to select the characters. Press
6666
or
7777
to move the cursor left or right.
Repeatedly press
VOL/CID
9999
to view
the characters in alphabetical order.
(The display shows uppercase letters
first, then lowercase letters, numbers,
and special characters.)
Notes:
• Press
VOL/CID
8888
to see the charac-
ters in reverse alphabetical order.
• You can hold down
VOL/CID
8888
or
9999
to scroll rapidly through the characters.
• If you make a mistake, move the cur-
sor over the error, then enter the correct character, or press
DEL
to delete
a character. To delete all the characters, hold down
DEL
for at least 1 sec-
ond.
43-5520.fm Page 16 Friday, July 21, 2000 8:01 AM
Page 17
17
Operation
6. Press
SELECT/CHANNEL
.
Store Num-
ber
appears.
7. Enter the phone number and any tone or
pause entries (see “Using T one Services
on a Pulse Line” on Page 15 and “Entering a Pause” on Page 18).
8. Press
SELECT/CHANNEL
. The phone
beeps and
<Memory nn Stored>
appears (nn is the memory location
number you selected).
After 2 seconds,
Memory Store
appears. Repeat Steps 3–8 to store
more numbers.
9. When you finish, press
MEM
.
To replace a stored number, store a new one
in its place.
Editing or Deleting a Number in
the Handset’s Memory
Follow these steps to edit or delete a memory number.
1. Lift the handset.
2. Hold down
MEM
until
Memory Store
and a list of memory location numbers
appear.
3. Choose a memory location (01–20) by
pressing a number or by repeatedly
pressing
VOL/CID
8888
or
9999
.
4. Press
SELECT/CHANNEL
. A menu
appears with the three options listed
below. Press
VOL/CID
8888
or
9999
to high-
light the desired option then press
SELECT/CHANNEL
to choose it.
Edit Memory nn
— edit the record as
described in Steps 5 through 7 of “Storing a Number in the Handset’s Memory”
on Page 16.
Delete Memory nn
— The display
prompts you to confirm the deletion.
Press
VOL/CID
8888
to move the cursor to
Yes
, then press
SELECT/CHANNEL
or
DEL
. The phone beeps, and
Memory
nn
Deleted
appears.
Go Back
— Returns you to the list of
memory numbers.
Storing a Number in
the Base’s Memory
Note:
The phone beeps five times and exits
the storing process if you wait more than 20
seconds between each keypress.
1. Press
MEM
. The CHARGE/IN USE indi-
cator blinks.
2. Enter the number (up to 16 digits) and
any tone or pause entries (see “Using
Tone Services on a Pulse Line” on
Page 15 and “Entering a Pause” on
Page 18).
Notes:
• The phone beeps five times and exits
the storing process if you enter more
than 16 digits.
• Each tone or pause entry uses one
digit of memory.
3. Press
MEM
again, then enter the mem-
ory location number (
0–9
) where you
want to store the phone number. The
phone beeps once.
To replace a number in the base’s memory,
simply store a new number in its place. To
erase a memory number, press
MEM
twice,
then press the memory location number (
0–
9
) you want to erase. The phone beeps once.
43-5520.fm Page 17 Friday, July 21, 2000 8:01 AM
Page 18
18
Operation
Entering a Pause
In some telephone systems, you must dial an
access code (9, for example) and wait for a
second dial tone before you can dial an outside number. You can store the access code
with the phone number. However, you
should also store a pause after the access
code to allow the outside line time to connect.
To enter a 2-second pause, press
PAUSE
(
RDL/PAUSE
on the handset). P appears if
you are storing a number into the handset’s
memory. You can add more pause entries
for a longer pause.
Reviewing the Handset’s
Memory Numbers
To review your handset’s memory numbers,
press
MEM
. The list of memory location num-
bers (
01–20
) appears with the name stored
with each number (or
<Memory nn>
if you
did not store a name).
To see the stored phone numbers, press
7777
.
An arrow to the right of the number means it
is longer than 13 digits. Press
7777
again to
see the rest of the number. Repeatedly press
6666
to return to the name display.
To exit the memory number list, press
MEM
.
To see a stored name and phone number at
the same time, press
SELECT/CHANNEL
when the cursor is by a memory location
number. To exit this display, hold down
DEL
until the display clears.
Dialing a Memory Number
To dial a number stored in the handset’s
memory, lift the handset and press
MEM
. The
list of memory location numbers appears.
Choose a memory location (01–20) by pressing a number or by repeatedly pressing
VOL/
CID
8888
or
9999
, then press
TALK
.
To dial a number stored in the base’s memory, press
SPEAKER
. When you hear a dial
tone, press
MEM
, then press the memory location number and the phone dials the number.
Note:
If you select an empty memory location in the base, the phone beeps five times.
Enter the correct memory location number.
Chain-Dialing Service Numbers
For quick recall of numbers for special services (such as bank by phone), store each
group of numbers in its own memory location. Dial the service’s main number first.
Then, at the appropriate place in the call,
press
MEM
and the number for the location
where the additional information is stored.
Testing Stored Emergency
Numbers
If you store an emergency service’s number
(police department, fire department, ambulance) and you choose to test the stored
number, make the test call during the late
evening or early morning hours to avoid peak
demand periods. Also, remain on the line to
explain the reason for your call.
USING A HEADSET
You can talk with hands-free convenience
using an optional headset that has a 3/32-inch
(2.5-mm) plug. Contact your local RadioShack store for a suitable headset.
To connect the headset, open the rubber
cover marked on the side of the handset,
then insert the headset’s plug into the jack.
43-5520.fm Page 18 Friday, July 21, 2000 8:01 AM
Page 19
19
Operation
Notes:
• Connecting a headset disconnects the
handset’s earpiece and microphone.
•
VOL/CID
8888
or
9999
on the handset also
controls the connected headset’s volume.
• If you place the handset on the base to
recharge it while the headset is connected, be sure the handset seats properly.
With a headset connected, you can make or
answer calls as usual using the speakerphone or the keys on the handset.
You can use a handset holder (available
from your local RadioShack store) to hang
the handset on your belt for greater convenience.
When you finish using the headset, disconnect it from the handset and close the rubber
cover to protect the jack.
CALLER ID OPERATION
If you subscribe to Caller ID service from
your phone company, the phone company
sends information about the call, as well as
the time and date, between the first and second rings of every call you receive.
The phone displays this information after the
second ring, and it stores up to 50 Caller ID
records for later review. It also shows if caller
information is unavailable or if the name and
number were blocked by the caller (“Caller
ID Messages”).
If you subscribe to Call Waiting with Caller
ID, you will hear a tone through the handset
when a call comes in, then the Caller ID
record appears. If you want to answer the incoming call, press
FLASH
. To resume the
previous phone conversation, press
FLASH
again.
If the phone’s Caller ID memory becomes
full, any new call replaces the oldest call’s
record.
Reviewing Caller ID Records
If the handset is faceup on the base, it shows
the number of new Caller ID records, if any,
and the total number of records.
To review the contents of each Caller ID
record, lift the handset and press
CALL ID
to
recall the number of records. Then, repeatedly press
VOL/CID
9999
to scroll through the
Caller ID records from the newest to the oldest, or
VOL/CID
8888
to scroll back through the
records. To scroll quickly through the
records, hold down
VOL/CID
8888
or
9999
.
When you scroll past the last record, the total
record number appears, then the first record.
When you scroll past the first record, the total
record number appears, then the last record.
The top line of each record shows the date,
time and the number of calls from that number. The second line shows the caller’s
name, and the third line shows the caller’s
phone number.
To exit the Caller ID record display, press
CALL ID
.
Caller ID Messages
Display Description
New: XX
Total: XX
Shows the number of new
Caller ID records (records
you have not reviewed) and
the total number of records.
Private
Name
or
Private
Number
The caller has blocked the
Caller ID information.
43-5520.fm Page 19 Friday, July 21, 2000 8:01 AM
Page 20
20
Operation
Adding/Deleting the Area Code
When the area code of the received call is
the same as the one you stored (see “Storing
Your Area Code” on Page 13), the caller ID
record does not show the area code. If it is
different, the record shows the area code.
However, you can add or delete the area
code. When the record is on the display,
press
3
to add or delete the area code.
Pressing
3
again deletes or adds the area
code.
When you dial the number or store it into
memory, the phone dials or stores the number as it appears.
Dialing Numbers from
a Caller ID Record
To dial a local number stored in a Caller ID
record, recall the record, then press
TALK
. If
it is a long distance call, press 1 (1 appears
before the displayed number) before you
press
TALK
. If you want to add or delete the
area code, press 3 before you press
TALK
.
Note:
If a Caller ID record does not contain a
phone number (if it was blocked by the caller,
for example) you cannot dial from that
record.
Storing a Caller ID
Record to Memory
Follow these steps to store the name and
number from a Caller ID record into a memory location.
1. Press
CALL ID
then
VOL/CID
8888
or
9999
to
recall the record you want to store.
2. If you want to add or delete the area
code, press
3
. If it is a long distance call,
press 1.
3. Press
MEM
.
Select Location
appears.
4. Choose a memory location (
01–20
) by
pressing a number or by repeatedly
pressing
VOL/CID
8888
or
9999
, then press
SELECT/CHANNEL
.
If the selected location is empty, the phone
beeps to confirm that it stored the number,
then the Caller ID record appears.
If a record exists in the selected location,
Replace Memory?
appears, prompting
you to confirm the replacement. Move the
cursor to
Yes
or No, then press
SELECT/
CHANNEL
.
Deleting Caller ID Records
You can delete Caller ID records individually
or all at once.
Follow these steps to delete a single Caller
ID record.
1. Press
CALL ID
then
VOL/CID
8888
or
9999
to
recall the record you want to delete.
2. Press
DEL
.
Delete Message?
and
Yes/No
appear with the cursor pointing
to
Yes
.
3. Press
SELECT/CHANNEL
or
DEL
. The
phone beeps once.
Unknown
Name
or
Unknown
Number
The caller is not within a
Caller ID service area.
Incomplete
Data
Appears if there was an
error during transmission of
Caller ID information. Occasional errors are normal. If
the phone frequently displays
Incomplete
Data
, contact your local
telephone company or
RadioShack store.
Display Description
43-5520.fm Page 20 Friday, July 21, 2000 8:01 AM
Page 21
21
Operation
Follow these steps to delete all Caller ID
records.
1. Press
CALL ID
so the record totals
appear.
2. Press
DEL
.
Delete All?
and
Yes/No
appear with the cursor pointing to No.
3. Press
VOL/CID
8888
to move the cursor to
Yes
, then press
SELECT/CHANNEL
or
DEL
. The phone beeps once and
Total:00
appears.
USING THE PHONE
COMPANY’S NETWORK
SERVICE
Your phone supports the advanced calling
services provided by many phone companies, such as Return Call, Repeat Dial, or
Cancel Call Waiting.
To use these features, you must be in an
area where those services are available and
you must subscribe to those services
through your phone company. Contact your
local telephone company for more details on
how to subscribe.
The phone has the following features preprogrammed in its memory.
Important:
Some phone companies use different key sequence to achieve the features.
Each section shows the built-in key sequence, so if your phone company uses different sequence, you need to edit the
sequence before using the service. See “Editing Service Name and Numbers” on
Page 22.
Notes:
• When using certain calling features,
local, toll or long distance charges might
apply.
• Y ou might not be able to use certain calling features on some long distance calls
or from certain types of business lines.
Follow these steps to access services.
1. Lift the handset.
2. Press
MENU
.
Return Call, Repeat
Dial
, and
Cancel CW
appear.
3. Press
VOL/CID
8888
or
9999
or 1, 2, or 3 to
select the service you want to use.
4. Press
TALK
. The selected service num-
ber appears and is dialed.
Feature Description Press
Return Call The service retains the
number of the party that
called you last and
automatically dials that
number. Return call is
useful if you miss an
incoming call.
69
Repeat Dial When you get a busy
signal or you want to
redial the last number
you called, the service
continuously redials the
number until the call
goes through.
66
Cancel Call
Waiting
Temporarily cancels
your Call Waiting service. This is useful
when you also use your
telephone line for internet service or sending/
receiving faxes. Enter
the key sequence prior
to dialing the internet or
fax number. Call Waiting is restored when
you disconnect the call.
70
43-5520.fm Page 21 Friday, July 21, 2000 8:01 AM
Page 22
22
Troubleshooting
Note:
You can display the programmed service number of each calling feature. At step 2
above, press
7777
to see the number and
6666
to return the list of services.
Editing Service Name
and Numbers
You might need to change the number
stored in any of the three service locations,
for example, if your phone company uses different number sequence from the programmed one.
Follow these steps to edit the key sequence.
1. Lift the handset.
2. Hold down
MENU
until
Select to
Edit
and list of calling features
appears.
3. Choose a calling feature by pressing a
number (
1–3
) or
VOL/CID
8888
or
9999
.
4. Press
SELECT/CHANNEL
. A menu listing
Edit, Restore
, and Go
Back
appears. Press
VOL/CID
8888
or
9999
to
highlight the desired option then press
SELECT/CHANNEL
to choose it.
Edit
—
Service name
appears.
Edit the service name and press
SELECT/CHANNEL
. Then,
Service
number
appears. Edit the number and
press
SELECT/CHANNEL
. Enter the
name and number as described in Steps
5 through 8 of “Storing a Number in the
Handset’s Memory” on Page 16.
Restore
— the display prompts you to
confirm the restoration. If you want to
return to the preprogrammed calling feature, press
VOL/CID
8888
to move the cur-
sor to
Yes
, then press
SELECT/
CHANNEL
. The phone beeps and
Ser-
vice
Setting Restored
appears.
Go Back
— returns you to the list of
service numbers.
ˆ
Troubleshooting
We do not expect you to have any problems with your phone, but if you do, these suggestions
might help.
Problem Suggestion
The phone does not work properly.
Be sure the base's phone line cord and AC adapter are correctly and
securely connected.
Be sure the battery pack in the handset is connected and charged.
Return the handset to the base for about 5 seconds to reset the secu-
rity access-protection code.
The display flashes slowly
when the handset is faceup on
the base.
Make sure the battery pack in the handset is properly connected.
The handset stops working or
works poorly during a call.
Move the handset closer to the base.
Lift the base's antenna to a fully vertical position.
Be sure the handset's battery pack is charged. (If the battery pack
power is too low, the handset cannot display
Low Battery
.)
43-5520.fm Page 22 Friday, July 21, 2000 8:01 AM
Page 23
23
Troubleshooting
If you still have problems, disconnect the phone. If other phones on the same line work properly, the fault is in this phone or its installation. If you cannot find the problem, ta ke the phone to
your local RadioShack store for assistance.
CARE
Keep the phone dry; if it gets wet, wipe it dry
immediately. Use and store the phone only in
normal temperature environments. Handle
the phone carefully; do not drop it. Keep the
phone away from dust and dirt, and wipe it
with a damp cloth occasionally to keep it
looking new.
Modifying or tampering with the phone’s internal components can cause a malfunction
and might invalidate its warranty and void
your FCC authorization to operate it. If your
phone is not performing as it should, take it
to your local RadioShack store for assistance. If the trouble is affecting the telephone
lines, the phone company can ask you to disconnect your phone until you have resolved
the problem.
Low volume or unusual
sounds.
Someone has picked up another phone on the same line. Hang up the
other phone.
Dropout or mute. Keep the handset away from computers, remote control toys, wireless
microphones, alarm systems, intercoms, room monitors, fluorescent
lights, and electrical appliances. Move to another location or turn off
the source of interference.
Press
SELECT/CHANNEL
to change the channel.
Hang up and redial the number.
The phone cannot be operated
at a useful distance from the
base because the signal
becomes weak or noisy (handset's range has decreased).
Lift the base's antenna to a vertical position.
Return the handset to the base and recharge the battery pack.
The handset battery pack does
not charge.
Check the charging contacts on the handset and base. If they are dirty ,
clean them with a pencil eraser.
Be sure the battery pack is connected correctly.
Be sure the handset is properly seated on the base.
Replace the battery pack (see “Connecting, Charging, and Replacing
the Battery Pack” on Page 9).
The handset does not ring or
receive a page.
Move the handset closer to the base.
Lift the base's antenna to a vertical position.
Be sure the battery pack in the handset is connected and charged.
Move the base away from other electrical devices.
Y ou have an incoming call, but
do not receive any Caller ID
information.
Let the phone ring twice before you answer so the phone has time to
record the Caller ID information.
Check that the phone is correctly and securely connected.
Check with your phone company to verify that your Caller ID service is
active.
Problem Suggestion
43-5520.fm Page 23 Friday, July 21, 2000 8:01 AM
Page 24
43-5520
UZZ01699ZZ
07A00
Printed in China
RadioShack Corporation
Fort Worth, Texas 76102
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workmanship under normal use for one (1) year from the date of purchase from RadioShack compan y- owned
stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED
HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVE NIENCE, LOSS
OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to
you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, unless otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the property of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinsta llation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102
We Service What We Sell
12/99
43-5520.fm Page 24 Friday, July 21, 2000 8:01 AM
Loading...