Radio Shack 6 × 9 Speaker Enclosures, 6 x 9 Speaker Enclosures Owner's Manual

6

××××

9 Speaker Enclosures

OWNER’S MANUAL — Please read before using this equipment.

Your RadioShack 6 × 9 Speaker Enclosures are designed to
hold most 6

9-inch, full-range, 2- and 3-way s peakers. The

×

enclosures are made of the highest quality materials to ensure
maximum response and sound quality in vehicle installations
and other areas with limited space.

Note: You need wood screws (not supplied) to install the
speakers in the enclosures. Check the number of mounting
holes on the speakers’ frames to de termine how many screws
you need. The screw size depends on the type of speaker you
install and the type of grille (if any).

MOUNTING THE ENCLOSURES

If you use the enclosures in a vehicle, mount the enclosures in
the vehicle before you install the speakers. Use the supplied
mounting hardware to mount the enclosures as follows:

1. Drill a

2. On the mounting surface, use a

3. Place a washer over a

4. Place the enclosure on the mounting surface, aligning the

1

/4-inch hole at the enclosure’s center point.

1

/4-inch drill bit to drill a

hole at the center point of the desired mounting location.

1

/4-inch bolt.

enclosure’s hole with the hole in the mounting surface.
Then, from the inside of the enclosure, insert the bolt
through the holes.

INSTALLING THE SPEAKERS

Follow these steps to install speakers in the enclosures.

1. Connect the speaker’s wires to the enclosure’s inside ter­minals by soldering the wires or by using clip-on terminals.
Be sure to connect the wire from th e speaker’s positive (+)
terminal to the enclosure’s positive terminal and the wire
from the speaker’s negative (–) terminal to the enclosure’s
negative terminal.

Speaker

Hint: You can improve the speaker’s sound by placing a

small amount of loosely packed acoustic insulation inside
the enclosure before you go to the Step 2.

2. Insert the speaker, magnet first, into the enclosure’s oval
hole. Then, align the speaker as needed.

Inside Terminals

Mounting
Bolt and
Washers

5. From the underside of the mounting surface, place a
washer and nylon locking nut over the bolt. Then, tighten
the nut.

6. Repeat Steps 1–5 to mount the other enclosure.

Bolt

Washers

Locking Nut

Mounting Surface

3. Using the speaker’s frame as a template, mark the
speaker’s mounting holes on the enclosure’s face. Then
use wood screws (not supplied) to secure the speaker to
the enclosure.

Wood Screws

Speaker

4. If the speaker includes a grille, attach the grille according to
its instructions.

5. Connect your sound system’s speaker wires to the spring
terminals on the back of the enclosure. Be sure you con­nect system’s wires (usually marked + for positive an d – f or
negative) to the corresponding positive and negative termi­nals on the enclosure.

6. Repeat Steps 1–5 to install the other speaker.

2000 Tandy Corporation.

©

RadioShack and RadioShack.com are trademarks used by Tandy Corporation.

All Rights Reserved.

Limited Ninety-Day Warranty

This product is warranted by RadioShack against manufacturing defects in material and workman­ship under normal use for ninety (90) days from the date of purchase from RadioShack company­owned stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED
HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES,
INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES
CONTAINED HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABIL­ITY OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RE­SPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE
OR PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WAR­RANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVE­NIENCE, LOSS OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT,
SPECIAL, INCIDENT AL, OR CONSEQ UENTIAL DAMAGES, EVEN IF RadioShac k HAS BEEN AD­VISED OF THE POSSIBILITY OF SUCH DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limit a­tion of incidental or consequential damages, so the above limitations or exclusions may not apply to
you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un­less otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the prop­erty of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.

RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102

We Service What We S ell

12/99

RadioShack
A Division of Tandy Corporation
Fort Worth, Texas 76102

40-171

03A00

Printed in USA