T H E P E R F O R M A N C E Y O U N E E D
TM
100W 2-Way
In-wall Speaker
Please read this user’s guide before using your new speaker.
User’s Guide 40-290
© 2009. Ignition L. P. All rights reserved. Auvio is a trademark used by Ignition L.P.
Package and insert are recyclable. Insert contains recycled material.
Package Contents
In-wall Speaker Template / Paint Mask
User’s Guide Quick Start
Features
Mount your speaker flush with the ceiling or wall with the
wing-type mounting system.
The frame and grille can be painted to match the room’s
decor.
The tweeter can be tilted to direct the sound to best suit
the room’s acoustics.
1 Installation
Prepare the location
To mount your speaker, you need the following items (not
supplied).
Drywall or keyhole saw
Wire stripper
Phillips screwdriver
Pencil or maker
18-20 gauge speaker wire
Be sure the mounting surface:
Is between 3/8 – 11/8 inch thick (9.5 – 32 mm)
Has at least 3 inches (76 mm) clearance behind the surface
Has no wall studs or other objects to block the back of
the speaker
w Warning: Be careful not to cut into existing wiring or
plumbing hidden behind the wall.
2
2
1. Remove the inner cardboard disc from
the supplied template/paint mask and
keep it for later. Use the outer portion
of the mask as a template to mark
the cutout hole size and location for
mounting the speaker.
2. Use a drywall or keyhole saw to cut
the hole.
Template
2 Connect to your amplifier
1. Route the speaker wire from your amplifier to the
speaker. Avoid routing near existing electrical wires and
do not nail or staple the wire.
2. Separate about 4 inches (100
mm) of wire at each end.
3. Using a wire stripper, remove
about 1/4 inch (6 mm) of
insulation from each wire. Then
twist the ends of each wire.
4. Connect the positive (marked) wire to the red speaker
terminal by pressing the tab, inserting the wire into the hole,
and releasing the tab. Repeat this procedure to connect the
negative (unmarked) wire to the black terminal.
6. Connect the wire coming from the red terminal to your
amplifier’s positive (+) terminal. Connect the wire from
the black terminal to your amplifier’s negative (–) terminal.
1
/4 inch
1
4 inches
4 inches
inch
/
4
AM
FM UNBAL
ANTENNA
Ω
LOOP
75
S-VIDEO cable Coaxial digital cable
Composite Video Cables Audio Cables Component Video Cables
SPEAKERS
CENTERSURROUND
FRONT
L
R
L
R
S
K
E
R
S
Screw
3
3
Tabs
3 Mount the speaker
1. Remove the grille to expose the mounting screws.
2. Be sure the mounting tabs are turned in, allowing the
speaker to fit into the hole. Then insert the speaker into
the mounting hole.
Mounting Tab
3. Tighten the six screws to secure the mounting tabs
to the wall or ceiling. Be careful not to overtighten the
screws.
4. Replace the grille.
n Note: To remove the speaker from the wall or ceiling,
loosen the screws only far enough to remove the speaker.
If you loosen the screws too far, you may lose the mounting
tabs behind your wall.
4
4
Painting the speaker (optional)
Before you connect the speaker wire or mount the speaker,
you can paint the frame and grille.
1. To remove the grille, insert a
paper clip into one of the grille
openings, then pull up.
2. Before you paint the grill, carefully
remove the dust cloth.
Frame
Grille
3. Before you paint the frame, insert the supplied
cardboard paint mask to prevent paint from entering the
speaker.
4. After the paint is dry, remove the paint mask, replace
the dust cloth, and reinstall the grille.
n Note: Using spray paint will keep paint from blocking
grille holes. Do not paint speaker components.
Specifications
Resonance Frequency ..............................................65 Hz ±20%
Frequency Response ..............................................70–20,000 Hz
Power Handling........................................ 50W RMS, 100W Max.
Impedance (nominal) ........................................................ 8 ohms
Sensitivity ................................................ 87 dB ±3 dB @ 1W-1M
Tweeter Size .............................................................1 in (25 mm)
Woofer Size ......................................................... 6.5 in (165 mm)
Dimensions (HWD) ..........12 × 8.6 × 2.8 in (305 × 218 × 70 mm)
Specifications are subject to change and improvement without notice. Actual
product may vary from the images found in this document.
Limited Warranty
Ignition L.P. warrants this product against defects in materials and workmanship
under normal use by the original purchaser for one (1) year after the date of
purchase. IGNITION L.P. MAKES NO OTHER EXPRESS WARRANTIES.
5
5
This warranty does not cover: (a) damage or failure caused by or attributable to
abuse, misuse, failure to follow instructions, improper installation or maintenance, alteration, accident, Acts of God (such as floods or lightning), or excess
voltage or current; (b) improper or incorrectly performed repairs by persons who
are not a Ignition L.P. Authorized Service Facility; (c) consumables such as fuses
or batteries; (d) ordinary wear and tear or cosmetic damage; (e) transportation,
shipping or insurance costs; (f) costs of product removal, installation, set-up
service, adjustment or reinstallation; and (g) claims by persons other than the
original purchaser.
Should a problem occur that is covered by this warranty, take the product and
the sales receipt as proof of purchase date to the place of purchase in the U.S.
Ignition L.P. will, at its option, unless otherwise provided by law: (a) repair the
product without charge for parts and labor; (b) replace the product with the same
or a comparable product; or (c) refund the purchase price. All replaced parts
and products, and products on which a refund is made, become the property
of Ignition L.P. New or reconditioned parts and products may be used in the
performance of warranty service. Repaired or replaced parts and products are
warranted for the remainder of the original warranty period. You will be charged
for repair or replacement of the product made after the expiration of the warranty
period.
IGNITION L.P. EXPRESSLY DISCLAIMS ALL WARRANTIES AND CONDITIONS
NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED WARRANTIES
THAT MAY BE IMPOSED BY LAW, INCLUDING THE IMPLIED WARRANTY
OF MERCHANTABILITY AND, IF APPLICABLE, THE IMPLIED WARRANTY OF
FITNESS FOR A PARTICULAR PURPOSE, SHALL EXPIRE ON THE EXPIRATION
OF THE STATED WARRANTY PERIOD.
EXCEPT AS DESCRIBED ABOVE, IGNITION L.P. SHALL HAVE NO LIABILITY
OR RESPONSIBILITY TO THE PURCHASER OF THE PRODUCT OR ANY
OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS OR
DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFORMANCE
OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY,
INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM
INCONVENIENCE AND ANY LOSS OF TIME, DATA, PROPERTY, REVENUE, OR
PROFIT AND ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES, EVEN IF IGNITION L.P. HAS BEEN ADVISED OF THE POSSIBILITY
OF SUCH DAMAGES.
Some States do not allow limitations on how long an implied warranty lasts or
the exclusion or limitation of incidental or consequential damages, so the above
limitations or exclusions may not apply to you. This warranty gives you specific
legal rights, and you may also have other rights which vary from State to State.
You may contact Ignition L.P. at:
Ignition L.P., 3102 Maple Ave, Suite 450, Dallas, TX 75201 02/09
For product support, call 1-866-315-0426
6
6
Protect the environment by recycling used electronics. Go to
E-CyclingCentral.com to find an electronic recycling center near you.
Get more from your audio and video equipment. See what
you’ve been missing. With Auvio, you control the experience.
Auvio was established by a group of technophiles to provide
high quality audio and video products without the high sticker
price. The Auvio philosophy is for you to experience audio
and video as it was intended to be: pure and distortion free.
We know electronics can be intimidating. Auvio simplifies
your experience by providing the right products, with the
right specs, to work with your equipment.
Be confident about your purchase: your new Auvio product
incorporates the latest technology, is built to the highest
quality standards, and reduces environmental impact by
complying with RoHS environmental restrictions.
Printed
in China
7
7
07A09
40-290
Loading...