Quikserv QST-625 Service Manual

Service Manual

QST-625 & QST-625S

QST-625 & QST-625S

Service Manual

Click the Procedure to View

Operation and Maintenance Procedures 2
Disassembly Procedures for Slide Rail Replacement 3
Disassembly Procedures for Slide Rail Replacement Cont. 4
Warranty Service Policy 5

Quikserv Corp.© quikserv.com • 1-800-388-8307 • Fax [phone]

1

Service Manual

QST-625 & QST-625S

Operation and Maintenance Procedures

Operation Procedures:

• Unlock all locking mechanisms and ensure
that the drawer is free of obstructions.

• Operate the drawer and return to the closed
position. The self-locking push bar will provide
daytime security.

• The rear thumb turn lock provides additional
nighttime security.

General Cleaning Guidelines:

• All drawers should be kept clean and free of
debris.

• Slide rails should be frequently cleaned, oiled,
and checked for debris and build-up.

• All cleaning uids and applicators should be

non-abrasive.

QST-625 & QST-625S

Quikserv Corp.© quikserv.com • 1-800-388-8307 • Fax [phone]

2

Service Manual

QST-625 & QST-625S

Transaction Drawer

Slide Rail Replacement

1. From the outer face of the drawer, remove
the two 6-32 screws from the underside of
the outer front vertical panel. Hold the bottom
of the outer front panel and pull out and up to
separate from the internal panel.

2. Remove the four 10-32 allen head screws
from the transaction inner tray.

Quikserv Corp.© quikserv.com • 1-800-388-8307 • Fax [phone]

3. Remove the two 10-32 allen head screws
from the rear of the front panel.

4. Remove the four 10-32 allen head screws
that connect the bottom of the drawer to the
rail assembly.

3

Service Manual

QST-625 & QST-625S

Transaction Drawer Disassembly Continued

5. From the inside of the drawer, pull the sliding
drawer back to the inside until it is latched in
place.

6. Push the drawer forward until the bolt heads
of the push handle side brackets will clear
the notch on the drawer housing.

Quikserv Corp.© quikserv.com • 1-800-388-8307 • Fax [phone]

7. Using the push handle, pull the sliding
drawer up and out.

8. Slide the inner rail race forward and remove
two 10-32 allen head screws which hold
each rail in place.

For installing new rails, simply reverse the
procedures outlined above.

4

Service Manual

Warranty Service Policy

QST-625 & QST-625S

1. Quikserv Corp. MUST be notied of a war­ranty situation before any work is performed.
Otherwise, Quikserv Corp. will not be respon­sible to pay for unauthorized work.

2. Quikserv Corp. requires the following on each
invoice submitted: an itemized account of work
performed detailing hours charged and parts
used, along with a short detailed description
of the problem noted.

3. Quikserv Corp. will authorize a set dollar
amount to be invoiced prior to performing ser­vices that will be rendered. This amount will
be determined from the initial call to the ser­vice company as a fair maximum. If additional
amounts are to be invoiced, they must be dis­cussed with Quikserv Corp. prior to invoicing.

4. A service technician on a warranty service call
needs to call our customer service department
at [phone] or [phone] before
leaving the job site.

5. A service company representative needs to
call the store where the work is to be per­formed prior to going to that store. Set up a
date and approximate time of arrival and if it
is foreseen that the agreed upon time cannot
be met, contact the store and make other ar­rangements.

7. Quikserv Corp. needs to be notied of any ex­tra parts - either to be sent back or to be kept
by the service technician. Any parts that were
replaced must be returned to Quikserv Corp.
if required verbally or on the service work or­der copy supplied with the parts sent by Qui­kserv Corp. If the parts are not returned, the
part cost + mark up will be deducted from the
service invoice.

8. A purchase order number will be given either
verbally or on the service work order from
Quikserv Corp. Please use this on all invoic­ing.

9. Work required on a window unit not covered
under Quikserv’s warranty must be reported
to Quikserv Corp. before work is begun.

10. Quikserv’s payment terms are net 30. The in­formation above will help us assure the fast-

est and most efcient service possible. For

further information or if you have any ques­tions, please do not hesitate to contact us at
[phone].

Customer Service Department

6. Warranty parts sent to service companies are
parts previously decided on that should cover
the necessary repairs. Additional parts will be

sent upon notication to Quikserv Corp.

Quikserv Corp.© quikserv.com • 1-800-388-8307 • Fax [phone]

5