Quikserv QSP-713-E Service Manual

Service Manual

Serial Number 4243 & Up

QSP-713-E

Serial Numbers 4243 & Up

QSP-713-E

Service Manual

Click the Procedure to View

Operation and Maintenance Procedures 2
Instructions to Convert from Electric Operation to Manual 3
Disassembly Procedures for QSP-713-E 4-5
Replacement Parts 6
Warranty Service Policy 7

Quikserv Corp.© quikserv.com • 1-800-388-8307 • Fax [phone]

1

Service Manual

QSP-713-E

Operation and Maintenance Procedures

Operation Procedures

• Unlock all locking mechanisms and ensure
that drawer is free of obstructions

• Make sure unit has power

• Push open button on the back of the drawer

to open

• Push close button on the back of the drawer
to close

General Cleaning Guidelines

• All drawers should be kept clean and free of
debris

• Slide rails should be frequently cleaned,
oiled, and checked for debris and build-up

• All cleaning fluids and applicators should be
non-abrasive

QSP-713-E

Serial Numbers 4243 & Up

Quikserv Corp.© quikserv.com • 1-800-388-8307 • Fax [phone]

2

Service Manual

Serial Numbers 4243 & Up

Instructions to Convert from Electric Operation to Manual

QSP-713-E

1. Disconnect the power source to the drawer
unit.

2. Remove the back cover panel while watching
the wires to the open/close switch.

3. Remove the top slide panel by removing the
2 screws at the top of the stainless back liner
of the drawer.

4. Manually push the drawer to the fully-opened
position. There will be some resistance at
this point in the process.

5. Remove the two hex head screws that attach
the aluminum mounting block to the rear of
the drawer liner.

Quikserv Corp.© quikserv.com • 1-800-388-8307 • Fax [phone]

6. After removing the two hex head screws
from the aluminum block, spin the aluminum
mounting block counter-clockwise to the
closed position (all the way back to the motor
coupling at the rear of the drawer)

7. There is a black knob in a bag attached
inside the drawer. Remove the knob from the
bag.

8. Screw the black threaded knob tightly into
the nutzert on the top of the serving area.

9. Drawer is now ready for manual operation.

3

STEP 1

STEP 2

BACK

COVER

LEESON

STEP 3

Service Manual

Figure 1

QSP-713-E

Serial Numbers 4243 & Up

Disassembly Procedures for QSP-713S-E

Disassembly Procedures for QSP-713S-E

1. Remove 8 screws holding back panel on.

2. Remove the 2 screws holding the back cover
on to the drawer liner.

3. Remove the 4 screws that hold back panel
together.

Quikserv Corp.© quikserv.com • 1-800-388-8307 • Fax [phone]

4

Service Manual

Disassembly Procedures for QSP-713S-E Continued

Figure 2

QSP-713-E

Serial Numbers 4243 & Up

4. Remove the 2 screws that hold super nut to
back panel.

5. Push back of drawer outwards to customer.

Quikserv Corp.© quikserv.com • 1-800-388-8307 • Fax [phone]

6. Remove 4 screws that hold slide rails to
bottom of drawer liner. Pull drawer liner
completely out.

5

Key No. Part No Description

A 8819 Bearing Block

B 1075 Lead Screw

D 1076 Super Nut

E 1077 Coupling

F 4458 Motor

G 1089 Push Buttons (2 pc's)

H 4459 Motor Drive

I 1083 Terminal Block

I

LEESON

H

F

G

A

E

D

B

Service Manual

QSP-713-E

Serial Numbers 4243 & Up

Parts Break Down

Quikserv Corp.© quikserv.com • 1-800-388-8307 • Fax [phone]

6

Service Manual

Warranty Service Policy

QSP-713-E

Serial Numbers 4243 & Up

1. Quikserv Corp. MUST be notified of a war­ranty situation before any work is performed.
Otherwise, Quikserv Corp. will not be respon­sible to pay for unauthorized work.

2. Quikserv Corp. requires the following on each
invoice submitted: an itemized account of work
performed detailing hours charged and parts
used, along with a short detailed description
of the problem noted.

3. Quikserv Corp. will authorize a set dollar
amount to be invoiced prior to performing ser­vices that will be rendered. This amount will
be determined from the initial call to the ser­vice company as a fair maximum. If additional
amounts are to be invoiced, they must be dis­cussed with Quikserv Corp. prior to invoicing.

4. A service technician on a warranty service call
needs to call our customer service department
at [phone] or [phone] before
leaving the job site.

5. A service company representative needs to
call the store where the work is to be per­formed prior to going to that store. Set up a
date and approximate time of arrival and if it
is foreseen that the agreed upon time cannot
be met, contact the store and make other ar­rangements.

7. Quikserv Corp. needs to be notified of any ex­tra parts - either to be sent back or to be kept
by the service technician. Any parts that were
replaced must be returned to Quikserv Corp.
if required verbally or on the service work or­der copy supplied with the parts sent by Qui­kserv Corp. If the parts are not returned, the
part cost + mark up will be deducted from the
service invoice.

8. A purchase order number will be given either
verbally or on the service work order from
Quikserv Corp. Please use this on all invoic­ing.

9. Work required on a window unit not covered
under Quikserv’s warranty must be reported
to Quikserv Corp. before work is begun.

10. Quikserv’s payment terms are net 30. The in­formation above will help us assure the fast­est and most efficient service possible. For
further information or if you have any ques­tions, please do not hesitate to contact us at
[phone].

Customer Service Department

6. Warranty parts sent to service companies are
parts previously decided on that should cover
the necessary repairs. Additional parts will be
sent upon notification to Quikserv Corp.

Quikserv Corp.© quikserv.com • 1-800-388-8307 • Fax [phone]

7