Page 1
Service Manual
Package Receiver
Package Receiver
Service Manual
Click the Procedure to View
Operation and Maintenance Procedures 2
General Cleaning Guidelines 2
Door Closer Adjustment for Package Receiver 3
Packager Receiver Disassembly Procedures 4
Replacement Parts 5
Warranty Service Policy 6
Quikserv Corp.© quikserv.com • 1-800-388-8307 • Fax (713) 849-5708
1
Page 2
Service Manual
Package Receiver
Operation and Maintenance Procedures
Operation Procedures:
1. Unlock all locking mechanisms and
Ensure that Package Receiver is free of
obstructions.
2. Open Package Receiver and load. Close
door. The other door now can be opened.
Return drawer to closed position.
3. The interior lock bar is for nighttime security.
General Cleaning Guidelines:
1. All Package Receivers should be kept clean
and free of debris.
2. Interior of Package Receiver should be
frequently cleaned and checked for debris
and build up.
3. Allcleaninguidsandapplicatorsshouldbe
non-abrasive.
Package Receiver
Quikserv Corp.© quikserv.com • 1-800-388-8307 • Fax (713) 849-5708
2
Page 3
H
I
EXTERIOR SIDE
Service Manual
Package Receiver
Package Receiver
Disassembly Procedures
Adjust Screw
Door Closer Adjustment for Package
Receiver
1. With the door closed, push tension
adjustment screw upward to release lock
position and turn left.
2. Test closing speed.
3. Turn left to increase closing speed.
Quikserv Corp.© quikserv.com • 1-800-388-8307 • Fax (713) 849-5708
3
Page 4
Key No. Part No. Description
A 5219 Shoulder Bolt
B 5214 Interlocking Eyebolt
C 8127 Pivot Arm Spacer
D 8126 Pivot Arm Body
E 8127 Linkage Arm (Glass Door)
E 8133 Linkage Arm (Steel Door)
F 8133 Linkage Arm
G 8129 1/2" Steel Ball Bearing
H 8124 Door Closer
I 8044 Door Handle
J 8125 Pivot Arm Middle
K 5743 Lock Bar
F
G
D
A
B
E
J
D
C
B
A
Service Manual
Package Receiver
Package Receiver
Disassembly Procedures
Disassembly procedures for Package
Receiver Pivot Arm replacement and
Lock Bar Replacement Procedures for
Package Receiver
Adjustment
1. Open outside door.
1. Remove two of Part # 5219 Shoulder Bolts.
2. Remove the two screws holding Part # 8126
Pivot Arm Body to unit.
3. Replace with new Pivot arms Part # 8127 &
8123 Depending on metal or glass door.
4. Replace with new Part # 8129 ½” Steel Ball
Bearing.
5. Adjust door tension by turning Part# 5214
clockwise or counter clockwise until only one
door will open at a time.
6. Tighten nuts on Part# 5214 after applying
non-permanent Lock-Tight.
Quikserv Corp.© quikserv.com • 1-800-388-8307 • Fax (713) 849-5708
2. Remove the two screws holding the lock bar
to the outside door.
3. Replace with new Pivot arms Part# 8127 &
8123 Depending on metal or glass door.
4. Replace with new Lock bar.
5. Tighten the two screws after applying nonpermanent Lock-Tight.
4
Page 5
Key No. Part No. Description
A 5219 Shoulder Bolt
B 5214 Interlocking Eyebolt
C 8127 Pivot Arm Spacer
D 8126 Pivot Arm Body
E 8127 Linkage Arm (Glass Door)
E 8133 Linkage Arm (Steel Door)
F 8133 Linkage Arm
G 8129 1/2" Steel Ball Bearing
H 8124 Door Closer
I 8044 Door Handle
J 8125 Pivot Arm Middle
K 5743 Lock Bar
F
G
D
A
B
E
J
D
C
B
A
H
I
EXTERIOR SIDE
Service Manual
Package Receiver
Replacement Parts
Quikserv Corp.© quikserv.com • 1-800-388-8307 • Fax (713) 849-5708
5
Page 6
Service Manual
Warranty Service Policy
Package Receiver
1. Quikserv Corp. MUST be notied of a warranty situation before any work is performed.
Otherwise, Quikserv Corp. will not be responsible to pay for unauthorized work.
2. Quikserv Corp. requires the following on each
invoice submitted: an itemized account of work
performed detailing hours charged and parts
used, along with a short detailed description
of the problem noted.
3. Quikserv Corp. will authorize a set dollar
amount to be invoiced prior to performing services that will be rendered. This amount will
be determined from the initial call to the service company as a fair maximum. If additional
amounts are to be invoiced, they must be discussed with Quikserv Corp. prior to invoicing.
4. A service technician on a warranty service call
needs to call our customer service department
at (800) 388-8307 or (713) 849-5882 before
leaving the job site.
5. A service company representative needs to
call the store where the work is to be performed prior to going to that store. Set up a
date and approximate time of arrival and if it
is foreseen that the agreed upon time cannot
be met, contact the store and make other arrangements.
7. QuikservCorp.needstobenotiedofanyextra parts - either to be sent back or to be kept
by the service technician. Any parts that were
replaced must be returned to Quikserv Corp.
if required verbally or on the service work order copy supplied with the parts sent by Quikserv Corp. If the parts are not returned, the
part cost + mark up will be deducted from the
service invoice.
8. A purchase order number will be given either
verbally or on the service work order from
Quikserv Corp. Please use this on all invoicing.
9. Work required on a window unit not covered
under Quikserv’s warranty must be reported
to Quikserv Corp. before work is begun.
10. Quikserv’s payment terms are net 30. The information above will help us assure the fast-
est and most efcient service possible. For
further information or if you have any questions, please do not hesitate to contact us at
(800) 388-8307.
Customer Service Department
6. Warranty parts sent to service companies are
parts previously decided on that should cover
the necessary repairs. Additional parts will be
sentuponnoticationtoQuikservCorp.
Quikserv Corp.© quikserv.com • 1-800-388-8307 • Fax (713) 849-5708
6
Loading...