February 2014
INSTALLATION MANUAL
QUANTUM
ROLLERSHADE HARDWARE SYSTEM
PAGE 2
CORNERS
Note: For windows in reveal brackets must be top
fixed for deductions to work.
FRONT EDGE
ON FACE
BACK EDGE
BAYS
ON FACE
TOP FIX FRONT EDGE
TOP FIX BACK EDGE
ANGLED LINKED BLINDS 90° CORNERS
FACE FIT
TOP FIT FRONT EDGE of REVEAL
Corners in Reveal- Front Edge Deductions
Through Blind +50mm(from corner)
Butt Blind - 0mm
Corners in Reveal- Back Edge Deductions
Through Blind - 0mm
Butt Blind - 60mm (37mm Tube)
- 80mm (50mm Tube)
Corners on Face Deductions (Butt Blinds)
38mm Projection bracket - 75mm
55mm Projection Bracket - 90mm
Bays in Reveal Deductions
Front Edge of Reveal - 0mm - 0mm - 0mm
Back Edge of Reveal - 22mm - 44mm - 22mm
Bays on Face Deductions
38mm Projection Bracket - 28mm - 56mm - 28mm
55mm Projection Bracket - 33mm - 66mm - 33mm
Angled Link Bay on Face Deductions
38mm Projection Bracket - 38mm - 76mm -38mm
55mm Projection Bracket - 43mm - 86mm -43mm
Angled Link Bay in Reveal Deductions
Front Edge of Reveal - 10mm - 20mm - 10mm
*Gap between Brackets 30mm approximate
Angled Link Corners on Face
Measure Blinds into the corner and deduct 76mm from each
blind.
Angled Link Corners in Reveal
Measure from the front edge of reveal and deduct 10mm
from each blind.
In all corner linked situations we strongly recommend
that the brackets are fixed in exact location first and then
measured outside edge to outside edge of the bracket to
ensure the gap is minimised.
*Gap between Brackets 30mm approximate
ANGLED LINKED BLINDS BAY WINDOW
MEASURE WALL
Brackets to be fixed to wall
CEILING FIT FRONT EDGE
OF REVEAL
FACE FIT
Deductions are only approximate due to thickness of fabric and drop, for
best results install the thru blind then measure for the butt blind.
QUANTUM MEASURING DEDUCTIONS
PAGE 3
QUANTUM INSTALLATION
1. Fix bracket with the screws
provided
2. Place the chain drive in the
bracket (1)
3. Slide it down until it
clicks (2).
4. Place the tube adapter on the
chain drive. Press the idle end
and lift the blind.
5. Snap it to the bracket. 6. Slide the end caps onto the
brackets.
1. Slide a screw driver between
idle end and bracket and
push the idle end in the chain
drive direction. Slide the end
cap towards you.
2. Move the blind downwards
out of the bracket.
3. Push the pin of the chain
drive and take the chain drive
out of the bracket.
4. Place a screw driver under the
pin of the chain drive and pull it
outwards. Remove chain drive
from the bracket.
REMOVAL - STANDARD ROLLER SYSTEM
INSTALLATION - STANDARD ROLLER SYSTEM
PAGE 4
INSTALLATION - STANDARD ROLLER SYSTEM WITH LEVELLER BRACKET
1. Make sure that the opening
for the Allen key is pointing
downwards before installing the
brackets. Change the orientation
by loosening the 2 screws and
turning the leveller 90°. Fix the
screws.
2. To adjust skewing, put the
provided Allen key into the
screw of the leveller and turn
it left or right to move the
blind up or down.
QUANTUM INSTALLATION
PAGE 5
QUANTUM INSTALLATION
INSTALLATION - LINKED BLINDS
1. Place the tube adaptor on the
chain drive head. Press the
idle end and lift the blind.
2. Fix the outer bracket with the
screws provided.
3. Slide the aligner or the
connector through the
bracket into the idle end.
4. Place the tube adaptor on the
aligner or connector head.
5. Press the spring loaded idle
with locking ring end and lift
the blind and snap it to the
bracket.
6. To align the bottom rails, push
the blind against the idle end
(1), turn the blind, level the
bottom rail with the other one
(2). Release to x the position
(3).
NOTE: This is not possible
when using the standard
connector set.
7. Fix the blind by turning the
locking ring against the idle
end.
8. Slide the end caps onto the
brackets.
NOTE: The aligner component has an extra metal bearing ring which is only required if the centre space
between two blinds is being extended. For normal installation this can be removed using an allen key.
PAGE 6
1. Slide the end cap towards
you.
2. Unfasten the locking ring.
Slide a screw driver between
locking ring and bracket
and push the idle end in the
aligner direction.
3. Move the blind downwards
out of the bracket. Pull the
aligner or connector out of
the idle end.
QUANTUM INSTALLATION
REMOVAL - LINKED BLINDS
1. Unfasten the locking ring. 2. Slide up the chain drive. 3. Push blind in the idle end
direction (2) and lower blind
to remove from bracket (3).
QUANTUM INSTALLATION
REMOVAL - SPRING BOOSTER
1
3
2
1
2
2
2
1
1. Place the idle end into the
bracket. Push blind in the idle
end direction (1) and lift blind
up (2).
2. Lift the blind up until chain
drive clicks in place (3).
QUANTUM INSTALLATION
INSTALLATION - SPRING BOOSTER
3
click
3. Fix the blind by turning the
locking ring against the idle
end.
PAGE 7
QUANTUM INSTALLATION
INSTALLATION - HEADBOX SYSTEM
1. Fix headbox back plate to wall
by drilling through extrusion
and slide brackets into keyway.
Tighten grubscrew.
3. Clip headbox front plate inside
keyway at the top of the
back plate.
NOTE: End cap removed for
demonstration only.
2. Slide end caps into the
headbox back plate.
4. Clip headbox front plate into
place to secure the endcaps.
1. Level the side guiding channel
ush with the headbox end
cap. Mark this position.
3. Fix the lower clip - and clips
at 1000 mm intervals - before
installing the channel.
2. Fix the top clip with a distance
max 7.5mm from the bottom
of the headbox end cap.
INSTALLATION - SIDE CHANNELS
4. Place the bottom rail into the
side guiding channel. Snap
and remove tab on chain
drive end.
5. Snap channel into clips.
Tab
PAGE 8
QUANTUM MANUAL
INSTALLATION MANUAL INFORMATION
This Installation Manual is only a guide to the measurement and installation procedures
for the Quantum Hardware System. New Zealand Window Shades Limited does not
warrant the accuracy contained in this manual.
The information contained in this Installation Manual is based on the measurement and
installation data known to us at the time of issue and is therefore subject to changes
or amendments at anytime without notice, and the right to change or amend is hereby
expressly reserved by New Zealand Window Shades Limited.
IMPORTANT
This Installation Manual at all times remains the property of New Zealand Window
Shades Limited. Its contents are strictly condential and may not be reprinted, copied,
reproduced or multiplied in any form. This Installation Manual must be maintained in
its original form and must be returned to New Zealand Window Shades Limited upon
rst request. New Zealand Window Shades Limited is not responsible to you or anyone
else for any loss suered in connection with the use of this Installation Manual or any
of the content.
© Copyright 2014 New Zealand Window Shades Limited
®
Registered Trade Marks of Hunter Douglas Limited.
NEW ZEALAND WINDOW SHADES LIMITED
PO BOX 12 785 PENROSE,
AUCKLAND 1642
NEW ZEALAND
Customer Service Phone: 0800 223 224
Loading...