QSC MX-1000-A Brochure
FEATURES
500 watts per channel at 2 ohms
400 watts per channel at 4 ohms
MX 1000a
he MX 1000a is a high power, low profile pro-
fessional power amplifier with advanced features and a flexible input. It delivers tremendous power in only two rack spaces, providing
high level performance under the most demanding conditions.
A stepped linear output circuit combines high
power with high efficiency to provide greater
average and dynamic audio performance, while
reducing normal system cooling and AC require-
ments by greater than 40%. An automatic twospeed fan matches cooling capacity with thermal requirements.
The rear panel uses Level 1 of QSC's exclusive
™
Open Input Architecture
which allows the use
of optional input connectors, input transformers, cinema crossovers, power limiters, precision attenuators, and other signal processing
cards as they become available.
Low profile—Only 2 rack spaces
high
High efficiency, 2-step output
circuit for improved thermal
performance and lower AC current
consumption
Split secondary configuration—
independent power supply on each
channel, for greater reliability
Quiet 2-speed fan
Independent DC, sub audio speaker
protection & thermal overload
protection on each channel
Open Input Architecture™–Level 1
Recessed calibrated front gain
controls for easy access &
protection from damage
Patented Output Averaging™ shortcircuit protection
Comprehensive LED status arrays
1/4" RTS and barrier balanced input
connectors
Mono-bridging/parallel switch
"Touch proof" binding post output
connectors
THX approved for cinema
applications
3 year warranty PLUS optional
3 year extended service contract
LOAD FTC CONTINUOUS AVERAGE EIA WATTS
Stereo (W/Ch)
8Ω 250 watts 275 watts
4Ω 350 watts 400 watts
2Ω 500 watts*
Mono-Bridged
16Ω 500 watts 550 watts
8Ω 700 watts 800 watts
4Ω 1000 watts*
®
A U D I O
20Hz-20kHz, 0.1% THD 1kHz, 1% THD
1675 MacArthur Boulevard
Costa Mesa, California 92626-1468 USA
Phone: 714/754-6175 Fax: 714/754-6174
*typical
..
TUV
PRODUCT
SERVICE
R
geprüfte
Sicherheit
OUTPUT POWER (per channel)
8 ohms, 20 Hz to 20 kHz, 0.1% THD, 250 watts
8 ohms, 1kHz, 1% THD, 275 watts
4 ohms, 20 Hz to 20 kHz, 0.1% THD, 350 watts
4 ohms, 1 kHz, 1% THD, 400 watts
2 ohms, 1 kHz, 1% THD, 500 watts*
OUTPUT POWER (bridged mono)
8 ohms, 20 Hz to 20 kHz, 0.1% THD, 700 watts
4 ohms, 1 kHz, 1% THD 1000 watts*
*typical
DISTORTION:
SMPTE-IM, less than 0.05%
FREQUENCY RESPONSE:
20 Hz to 20 kHz, ±0.15 dB
8 Hz to 100 kHz, +0/-3 dB
BACK
DAMPING FACTOR:
Greater than 200
DYNAMIC HEADROOM: 3 dB at 4 ohms
NOISE: 100 dB below rated output (20 Hz to 20 kHz)
SENSITIVITY: 1.12 Vrms for rated power (8 ohms)
VOLTAGE GAIN: 40 (32 dB)
INPUT IMPEDANCE: 10K unbalanced, 20K balanced
CONTROLS:
Front: AC Switch, Ch 1 and Ch 2 Gain Knobs
Back: Parallel/Stereo/Bridge Switch
INDICATORS:
PWR-ON: Green LED
SIGNAL PRESENT: Yellow LED
CLIP: Red LED
PROT: Red LED
MX 1000a Specifications
CONNECTORS: (each channel)
Input: Barrier strip and 1/4" RTS
Speakers: "Touch proof" binding posts
COOLING: Two-speed fan, rear-to-front air flow.
AMPLIFIER PROTECTION:
Full short circuit†, open circuit, ultrasonic, and RF protection. Stable into reactive or mismatched
loads.
LOAD PROTECTION:
On/off muting. DC-fault load grounding relay with internal fault fuses.
OUTPUT CIRCUIT TYPE:
Complementary linear outputs, 2 step high efficiency circuit.
POWER REQUIREMENTS: 100,120, 240 Vac, 50-60 Hz
POWER CONSUMPTION:
Normal Operation: 4 ohms per channel: less than 7.5 amps, 120 Vac (900 VA) maximum (full power,
2 ohms per channel): 22 amps, 120 Vac (2640 VA)
DIMENSIONS:
19.0" (48.3 cm) rack mounting
3.5" (8.9 cm) tall (2 spaces)
17.9" (45.5 cm) deep (rear support ears)
WEIGHT: 42 Ibs (19.1 kg) net, 49 Ibs (22.2 kg) shipping
†Output Averaging™ short circuit protection (US Patent 4,321,554)
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.
ARCHITECT’S AND ENGINEER’S SPECIFICATIONS
The amplifier shall contain all solid-state circuitry, using complementary
silicon output devices. The amplifier shall exceed the efficiency of an ordinary class-B linear output circuit. Overall electrical efficiency, with four
or eight-ohm loads, shall exceed 35% at 1/3 power and 29% at 1/8 power.
The amplifier shall operate from 50-60 Hz AC power, with internal taps for
selecting voltages 100,120, or 220-240 Vac. The amplifier shall operate
from a normal household AC outlet, drawing less than 900 VA when driven
with random program material at 1/8 rated power into four ohm loads.
The amplifier shall be supplied with a single molded AC cord having an
appropriate AC plug for the intended operating voltage.
The amplifier shall employ forced-air cooling with a two speed fan for
minimum acoustic noise. Air flow shall be from rear to front to avoid temperature rise inside the rack. Rack mounting shall be possible without
clearance necessary between amplifiers for ventilation. The amplifier shall
be capable of continuous operation at 1/8 power, into four -ohm loads, for
ambient temperatures up to 104° F (40° C).
The amplifier shall contain two independent channels, with separate AC
transformer secondaries, power supplies, and protection systems. All protection systems shall be self resetting upon removal of fault, and the remaining channel shall continue to operate. Each channel shall have independent protective circuitry against open circuit, short circuit, or mismatched loads. Each channel shall monitor temperature of its heat sink
and power transformer, and shall trigger fan speed boost, and if necessary, signal muting to prevent excessive temperature rise. Each channel
shall have on-off muting, acting for three seconds after turn-on, and within
1/4 second after turn-off or loss of AC power. Each channel shall have DC
fault protection for the load, consisting of a load-grounding relay with
fault fusing to interrupt power. Fault fuses shall be adequately large to
prevent nuisance blowing at any output power the amplifier is capable of
delivering.
Each channel shall have the following controls and displays: A front panel
Gain control, a green LED power-on indicator; one yellow LED signal indicator, triggering at -30 dB; a red LED showing true amplifier clipping; and
a red LED which indicates muting when illuminated.
The output connectors for each channel shall include a "touch proof" binding post.
The input connectors shall be mounted on a removable panel to permit
upgrades. The standard input panel shall provide barrier strip and 1/4"
connections for each channel. Inputs shall be electronically balanced, with
a minimum impedance of 10 kilohms per side, and a common mode rejection of at least 50 dB from 20 Hz to 20 kHz. The standard input panel shall
contain switches for mono-bridging and parallel inputs, and solder patterns for input isolation transformers, gain reduction resistors, and firstorder high and low pass filters .
The input panel shall have enough space behind it to contain a circuit
board measuring up to 5.9" wide by 4.1 “ deep. The multi-pin connector to
the amplifier circuitry shall supply positive and negative DC supply currents, and for each channel, balanced input signals, output signal, and
clip/protect signal.
Each channel shall be capable of meeting the following performance criteria with both channels driven: Sine-wave output power of 250 watts
into eight ohms, and 350 watts into four ohms, 20Hz to 20kHz, with less
than O.1% THD. Frequency response at 3dB below rated power shall be
20Hz to 20kHz within O.15 dB. The voltage gain shall be 40, equivalent to
32dB, and the input sensitivity shall be 1.12 Vrms. The signal to noise
ratio over the range of 20 Hz to 20 kHz shall exceed 100 dB unweighted.
IHF damping factor shall exceed 200.
The amplifier chassis shall occupy two rack spaces, with provision for
securing the rear corners. Depth from mounting surface to tips of rear
supports shall be 17.9" (45 5 cm).
Weight shall not exceed 42 Ibs. (19.1 kg.). The amplifier shall be the QSC
Audio Products Model MX 1000a.
A U D I O
®
1675 MacArthur Boulevard
Costa Mesa, California 92626-1468 USA
Phone: 714/754-6175 Fax: 714/754-6174
Loading...