QSC K8.2, K12.2, K10.2 Quick Start Guide

K.2 Series

Yoke Mounting Quick Start Guide

EXPLANATION OF SYMBOLS

The term “WARNING!” indicates instructions regarding personal safety. If the instructions are not followed the result may be
bodily injury or death.

The term “CAUTION!” indicates instructions regarding possible damage to physical equipment. If these instructions are not
followed, it may result in damage to the equipment that may not be covered under the warranty.

The term “IMPORTANT!” indicates instructions or information that are vital to the successful completion of theprocedure.

The term "NOTE" is used to indicate additional useful information.

The intent of the lightning flash with arrowhead symbol in a triangle is to alert the user to the presence of un­insulated "dangerous" voltage within the product's enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to humans.

The intent of the exclamation point within an equilateral triangle is to alert the user to the presence of important
safety, and operating and maintenance instructions in this manual.

IMPORTANT SAFETY INSTRUCTIONS

WARNING!: These mounting brackets shall only be used with K.2 Series loudspeakers. Use with other
apparatus could result in instability and possible injury.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Only use attachments/accessories specified by the manufacturer.

6. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any
way, or has been dropped.

7. Adhere to all applicable, local codes.

8. Consult a licensed, professional engineer when any doubt or questions arise regarding a physical
equipmentinstallation.

9. Before placing or installing any loudspeaker product, inspect all hardware, cabinets, transducers, brackets and
associated equipment for damage. Any missing, corroded, deformed, or non-load rated component could
significantly reduce the strength of the installation and should be immediately corrected. Use only hardware which is
rated for the loading conditions of the installation and any possible short-term unexpected overloading. Never exceed
the rating of the hardware or equipment.

TD-000524-00-A

*TD-000524-00*

Warranty

For a copy of the QSC Limited Warranty, visit the QSC website at www.qsc.com

Yoke Mounting the K.2 Series Loudspeakers

WARNING!: Read and follow these instructions carefully. If the loudspeakers are not installed properly, they could fall,
causing personal injury or death, and damage to the equipment.

Rules for Mounting

EN

• Consult a Professional Mechanical or Structural Engineer, licensed in the

jurisdiction of the sound system installation, to review, verify, and approve all
attachments to the building or structure.

• Employ the services of a Professional Rigger for hoisting, positioning, and

attaching the equipment to the supporting structure.

• Correct use of all mounting hardware and components is imperative in sound system installation and deployment.

• Consult local codes and regulations to fully understand the requirements for installed loads in the venue in which you

will install theequipment.

• Use only the recommended yoke for installing the loudspeaker.

• Be absolutely certain of the integrity of any structural member intended to support the loudspeaker(s). Hidden

structural members can have hidden structural weakness.

• Never assume anything! Owner or third-party supplied attachment points may not be adequate for installing

theloudspeakers.

• Before lifting, always inspect all components (enclosures, brackets, pins, frames, bolts, nuts, etc.) for cracks, wear,

deformation, corrosion, missing, loose, or damaged parts that could reduce the strength of the assembly. Discard any
worn, defective, or suspect parts and replace them with new appropriately load-rated parts.

Model Weight (kg) Weight (lbs)

K8.2 12.2 27

K10.2 14.5 32

K12.2 17. 7 39

Yoke Mounting

Each model has four yoke-mounting points, one on each side, one on top, and one on the bottom of the enclosure. The
bottom mounting point requires the pole-cup adapter included in the Yoke Mounting kit.

Yoke Installation Options

TD-000524-00-A

Adjustable distance from the
mounting surface.

— Figure 1 —

2