How it Works
QNAP
Loading...
TS-1886XU-R
User Manual
53 pgs2.64 Mb0
Table of contents
Loading...

QNAP TS-1886XU-R User Manual

TS-1886XU-RP
User Guide
Document Version: 2 02/03/2020
TS-1886XU-RP User Guide

Contents

1. Preface
About This Guide.......................................................................................................................................... 3
Audience.......................................................................................................................................................3
Document Conventions................................................................................................................................ 3
2. Product Overview
Front Panel...............................................................................................................................................8
Rear Panel................................................................................................................................................8
Rear Panel Network Interface.................................................................................................................. 9
Rear Panel LED......................................................................................................................................10
System Board.........................................................................................................................................10
Drive Numbering.....................................................................................................................................11
3. Installation and Configuration
Hardware Installation.................................................................................................................................. 14
Drive Installation.....................................................................................................................................14
Removing the Case Cover..................................................................................................................... 19
Attaching the Case Cover.......................................................................................................................20
Replacing Memory Modules...................................................................................................................22
Replacing Expansion Cards................................................................................................................... 24
Hot-Swapping Redundant Power Supply Units......................................................................................27
Rail Kits.................................................................................................................................................. 28
Expansion Unit Installation..................................................................................................................... 28
QTS Installation.......................................................................................................................................... 33
Installing QTS Using Qfinder Pro........................................................................................................... 34
Installing QTS Using the Cloud Key....................................................................................................... 35
4. Basic Operations
Power Button.............................................................................................................................................. 37
Reset Button............................................................................................................................................... 37
LEDs........................................................................................................................................................... 37
Audio Alert.................................................................................................................................................. 39
5. Troubleshooting
6. Glossary
1
QTS.............................................................................................................................................................42
7. Notices
2
TS-1886XU-RP User Guide

1. Preface

About This Guide

This guide provides information on the QNAP TS-1886XU-RP NAS and step-by-step instructions on installing the hardware. It also provides instructions on basic operations and troubleshooting information.

Audience

This document is intended for storage administrators. This guide assumes that the user is knowledgeable and qualified to install, maintain, and troubleshoot issues involving servers, server components, and storage systems. This guide also assumes that the user is trained to recognize hazards, including the appropriate actions the user needs to take to prevent personal injury and damage to data and property.

Document Conventions

Symbol Description
Notes provide default configuration settings and other supplementary information.
Important notes provide information on required configuration settings and other critical information.
Tips provide recommendations or alternative methods of performing tasks or configuring settings.
Warnings provide information that, when ignored, may result in potential loss, injury, or even death.
Preface 3
TS-1886XU-RP User Guide

2. Product Overview

This chapter provides basic information about the QNAP TS-1886XU-RP NAS.

About the TS-1886XU-RP

The TS-1886XU-RP is an enterprise rackmount NAS that provides an economic yet powerful enterprise storage solution. Powered by the latest enterprise Intel® Xeon® D processors, the TS-1886XU-RP possesses high computing capacity for supporting QNAP's automated data tiering feature, Qtier, while ensuring data integrity. The new Intel® Xeon® D processors support DDR4 Error Correcting Code (ECC) memory to ensure data integrity and reliability. Additionally, the TS-1886XU-RP can be scaled to meet different enterprise networking needs. The NAS is loaded with dual-channel long-DIMM DDR4 memory that can be scaled up to 128 GB, and equipped with four PCIe 3.0 slots to accomodate multiple network and accelerator cards. The TS-1886XU-RP supports up to 18 bays that works with 3.5-inch hard drives and 2.5­inch solid-state drives for delivering excellent SSD caching and data tiering performance.

Hardware Specifications

Warning
• If your QNAP product has hardware defects, return the product to QNAP or a QNAP­authorized service center for maintenance or replacement. Any attempt to repair or perform maintenance procedures on the product by you or an unauthorized third-party invalidates the warranty.
• QNAP is not responsible for any damage or data loss caused by unauthorized modifications and installation of unsupported third-party applications. For details, see the QNAP Warranty Terms and Conditions.
Ordering P/N CPU Memory Power supply
TS-1886XU-RP-D1602-4G Intel® Xeon® D-1602 4 GB Redundant
TS-1886XU-RP-D1622-8G Intel® Xeon® D-1622 8 GB Redundant
Component TS-1886XU-RP-D1602-4G TS-1886XU-RP-D1622-8G
Processor
CPU Intel® Xeon® D-1602 Intel® Xeon® D-1622
Frequency Dual-core/4-thread 2.50 GHz/3.2
GHz burst
Architecture x86 64-bit
Encryption engine AES-NI
Memory
Pre-installed memory 4 GB RAM: 1 x 4 GB UDIMM
DDR4 ECC
Quad-core/8-thread 2.60 GHz/3.2 GHz burst
8 GB RAM: 2 x 4 GB UDIMM DDR4 ECC
Product Overview 4
Component TS-1886XU-RP-D1602-4G TS-1886XU-RP-D1622-8G
Memory slots 4 x Long-DIMM DDR4
Important
• Use only QNAP memory modules to maintain system performance and stability. For NAS devices with more than one memory slot, use QNAP modules with identical specifications.
• Using unsupported modules may degrade performance, cause errors, or prevent the operating system from starting.
Maximum memory 128 GB
Flash memory 5 GB (dual-boot OS protection)
Storage
Drive bays • 12 x 3.5-inch SATA 6 Gbps
• 6 x 2.5-inch SATA 6 Gbps
TS-1886XU-RP User Guide
Tip
The drive bays are backward compatible with SATA 3 Gbps drives.
Drive compatibility 3.5-inch bays:
• 3.5-inch SATA hard disk drives
• 2.5-inch SATA hard disk drives
• 2.5-inch SATA solid-state drives
2.5-inch bays:
2.5-inch SATA solid-state drives
SSD cache acceleration support • 3.5-inch drive bays: 1 to 12
• 2.5-inch drive bays: 13 to 18
Hot-swapping Supported
Network
10 Gigabit Ethernet ports 2 x 10GbE SFP+ SmartNIC port
Gigabit Ethernet ports 4 x GbE RJ45
External I/O Ports & Expansion Slots
Product Overview 5
Component TS-1886XU-RP-D1602-4G TS-1886XU-RP-D1622-8G
PCIe slots • 2 x PCIe Gen 3.0 x4
• 2 x PCIe Gen 3.0 x8
Important
• A dual-port 10 GbE SFP+ network expansion card is pre-installed in the PCIe slot.
• Certain PCIe slot lengths are affected by the installation of expansion cards in neighboring PCIe slots. For details, see Installing Expansion Cards.
Tip
For the list of compatible expansion cards, go to
https://www.qnap.com/compatibility.
USB ports 2 x USB 3.0 Type-A
Interface
Buttons • Power
TS-1886XU-RP User Guide
• Reset
Dimensions
Form factor 2U Rackmount
Dimensions (H x W x D) 88.3 x 482 x 549.7 mm
(3.48 x 18.98 x 21.64 in)
Net weight 12.73 kg (28.06 lbs)
Others
Rail compatibility RAIL-B02
Note
• Rail kits are not included with the NAS and must be purchased separately. For details, contact an authorized reseller or go to http://shop.qnap.com.
• Information on rail kit installation can be found in the installation guide included in the rail kit package.
Power supply unit TS-1886XU-RP: 2 x 550W, 100-240V AC, 50/60 Hz
Warning
To reduce the risk of fire or electric shock, ensure that you only connect the power cord to a properly grounded electrical outlet.
Product Overview 6
Component TS-1886XU-RP-D1602-4G TS-1886XU-RP-D1622-8G
System battery CR2032 lithium battery (3V, 225 mAh)
Warning
To avoid potential battery explosion, causing injury or damage to components, ensure that you replace the existing battery with a battery of the same type.
Important
Dispose of used batteries according to local regulations or the instructions of the battery manufacturer.
Sound level 56.9 db(A)
Note
The sound level was tested at a bystander position, which is within one meter of the NAS. The test NAS operated at low speed with the maximum number of drives installed.
TS-1886XU-RP User Guide
Fans System: 3 x 60 mm, 12V DC fans
Warning
To avoid potential injury or damage to components, do not touch the fans while the NAS is connected to a power source.
Operating temperature 0˚C to 40˚C (32˚F to 104˚F)
Relative humidity • Non-condensing relative humidity: 5% to 95%
• Wet-bulb temperature: 27˚C (80.6˚F)
Tip
Model specifications are subject to change without prior notice. To see the latest specifications, go to https://www.qnap.com.

Package Contents

Item Quantity
TS-1886XU-RP 1
Power cord 2
Ethernet cables 2
Screws for 3.5-inch drives 48
Screws for 2.5-inch drives 64
Quick Installation Guide (QIG) 1

Components

Product Overview 7

Front Panel

TS-1886XU-RP User Guide
No. Component No. Component
1 3.5-inch drive LEDs 4 LAN LED
2 Power button 5 Expansion unit LED
3 Status LED -

Rear Panel

No. Component No. Component
1 USB 3.1 Gen 1 Type-A port 4 Power supply unit 2
Product Overview 8
No. Component No. Component
2 PCIe low-profile covers 5 Tool port
Note
This port is only for engineering purposes.
3 Power supply unit 1 6 Reset button

Rear Panel Network Interface

TS-1886XU-RP User Guide
No. Component Specifications
1 Ethernet port 3 GbE RJ45
2 Ethernet port 1 GbE RJ45
3 Ethernet port 6 10GbE SFP+
4 Ethernet port 5 10GbE SFP+
5 Ethernet port 2 GbE RJ45
6 Ethernet port 4 GbE RJ45
Product Overview 9

Rear Panel LED

TS-1886XU-RP User Guide
No. Component No. Component
1 Gigabit Ethernet speed LED 4 10 Gigabit Ethernet activity LED
2 Gigabit Ethernet activity LED 5 Drive status LED
3 10 Gigabit Ethernet speed LED 6 Drive activity LED

System Board

No. Component Specifications
1 Memory slot 1 Long-DIMM DDR4
Product Overview 10
No. Component Specifications
2 Memory slot 2 Long-DIMM DDR4
3 Memory slot 3 Long-DIMM DDR4
4 Memory slot 4 Long-DIMM DDR4
5 PCIe slot 4 PCIe 3.0 x8
Note
A 10GbE SFP+ SmartNIC card is pre-installed in this PCIe slot.
6 PCIe slot 3 PCIe 3.0 x4
7 PCIe slot 2 PCIe 3.0 x8
8 PCIe slot 1 PCIe 3.0 x4

Drive Numbering

TS-1886XU-RP User Guide
Front panel 3.5-inch drive bays
Product Overview 11
Rear panel 2.5-inch drive bays
TS-1886XU-RP User Guide

Installation Requirements

Category Item
Environment • Room temperature: 0˚C to 40˚C (32˚F to 104˚F)
• Non-condensing relative humidity: 5% to 95%
• Wet-bulb temperature: 27˚C (80.6˚F)
• Flat, anti-static surface without exposure to direct sunlight, liquids, or chemicals
• Free from objects that may obstruct NAS ventilation or apply pressure to the NAS or power cord
Hardware and peripherals • Storage drives
For the list of compatible drive models, go to https://
www.qnap.com/compatibility.
• Network cable
Tools • Phillips #1 or #2 screwdriver
• Flat head screwdriver
• Anti-static wrist strap

Setting Up the NAS

1. Place your NAS device in an environment that meets the requirements.
For details, see Installation Requirements.
2. Install the drives. For details, see the following topics:
Product Overview 12
TS-1886XU-RP User Guide
• Installing 3.5-inch Hard Drives on 3.5-inch Trays
• Installing 2.5-inch Hard Drives or Solid-State Drives on 3.5-inch Trays
• Installing 2.5-inch Hard Drives or Solid-State Drives on 2.5-inch Trays
For a list of compatible drives and expansion cards, go to http://www.qnap.com/compatibility.
3. Optional: Replace expansion cards. For details, see Replacing Expansion Cards.
4. Optional: Replace memory modules. For details, see Replacing Memory Modules.
5. Optional: Install the NAS on a rack. For details, see Rail Kits.
6. Optional: Connect the expansion units. For details, see Expansion Unit Installation.
7. Connect the power cord and all applicable cables.
8. Power on the NAS.
For details, see Front Panel.
9. Install QTS. For details, see QTS Installation.
10. Log on to QTS.
Product Overview 13
TS-1886XU-RP User Guide

3. Installation and Configuration

This chapter provides specific hardware and firmware installation and configuration steps.

Hardware Installation

This section provides information on installing drives, memory modules, and expansion cards.

Drive Installation

The TS-1886XU-RP is compatible with 3.5-inch hard drives, 2.5-inch hard drives, and 2.5-inch solid-state drives.
Installing 3.5-inch Hard Drives and Solid-State Drives on 3.5-inch Trays
For the list of compatible drive models, go to https://www.qnap.com/compatibility.
Warning
• Installing a drive deletes all data on the drive.
• Observe electrostatic discharge (ESD) procedures to avoid damage to components.
1. Power off the NAS.
2. Remove the drive tray.
a. Pull the handle to release the tray.
b. Pull the tray out.
3. Install a drive on the tray.
a. Place the drive on the tray so that the holes on the bottom of the drive are aligned with the holes
on the bottom of the tray.
Installation and Configuration 14
b. Attach the screws.
TS-1886XU-RP User Guide
4. Load the tray into the bay.
a. Insert the tray into the bay.
b. Push the handle.
5. Power on the NAS.
Installation and Configuration 15
Loading...
+ 37 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use