Q-Logic 5200, 5202 User Manual

0
Simplify
SANbox 5200 Series
Switch Management User’s Guide
Firmware Version 4.2
59056-02 A Page i
Information furnished in this manual is believed to be accurate and reliable. However, QLogic Corporation assumes no responsibility for its use, nor for any infringements of patents or other rights of third parties which may result from its use. QLogic Corporation reserves the right to change product specifications at any time without notice. Applications described in this document for any of these products are for illustrative purposes only. QLogic Corporation makes no representation nor warranty that such applications are suitable for the specified use without further testing or modification. QLogic Corporation assumes no responsibility for any errors that may appear in this document.
QLogic, SANbox, SANsurfer, SANblade, SANsurfer Switch Manager, and SANsurfer Management Suite are trademarks or registered trademarks of QLogic Corporation.
Java and Solaris are registered trademarks of Sun Microsystems, Inc.
Gnome is a trademark of the GNOME Foundation Corporation. Linux is a registered trademark of Linus Torvalds. Microsoft, Windows NT, Windows 2000, Windows 2003, and Internet Explorer are trademarks of Microsoft
Corporation. Netscape Navigator and Mozilla are registered trademarks of Netscape Communications Corporation. Red Hat is a registered trademark of Red Hat Software Inc. All other brand and product names are trademarks or registered trademarks of their respective owners.
0
Document Revision History
Release, Revision A, September 2004
© 2000–2005 QLogic Corporation
First Printed: May 2001
All Rights Reserved Worldwide.
Printed in U.S.A.
Page ii 59056-02 A

Table of Contents

Section 1 Introduction
1.1 Intended Audience ............................................................................................. 1-1
1.2 Related Materials ............................................................................................... 1-1
1.3 JDOM License.................................................................................................... 1-2
1.4 Technical Support............................................................................................... 1-3
1.4.1 Availability.................................................................................................. 1-3
1.4.2 Training......................................................................................................1-3
1.4.3 Contact Information ................................................................................... 1-3
Section 2 Using SANsurfer Switch Manager
2.1 Installing the Management Application............................................................... 2-1
2.1.1 SANsurfer Switch Manager ....................................................................... 2-2
2.1.2 SANsurfer Management Suite................................................................... 2-3
2.1.2.1 SMS Installation for Windows........................................................... 2-3
2.1.2.2 SMS Installation for Linux................................................................. 2-5
2.1.2.3 SMS Installation for Solaris...............................................................2-6
2.2 Starting SANsurfer Switch Manager................................................................... 2-8
2.3 Exiting SANsurfer Switch Manager .................................................................. 2-10
2.4 Uninstalling SANsurfer Switch Manager .......................................................... 2-12
2.4.1 SMS Uninstall.......................................................................................... 2-12
2.4.2 Standalone Uninstall................................................................................2-13
2.5 Changing the Encryption Key for the Default Fabric View File......................... 2-13
2.6 Saving and Opening Fabric View Files ............................................................ 2-14
2.7 Setting SANsurfer Switch Manager Preferences ............................................. 2-14
2.8 Using Online Help ............................................................................................ 2-16
2.9 Viewing Software Version and Copyright Information ...................................... 2-16
2.10 SANsurfer Switch Manager User Interface ...................................................... 2-17
2.10.1 Menu Bars ............................................................................................... 2-18
2.10.1.1 Topology Display Menu .................................................................. 2-18
2.10.1.2 Faceplate Display Menu ................................................................. 2-19
2.10.1.3 Topology Display Shortcut Keys..................................................... 2-20
2.10.1.4 Faceplate Display Shortcut Keys.................................................... 2-21
2.10.2 Tool Bar ................................................................................................... 2-23
2.10.3 Fabric Tree .............................................................................................. 2-24
2.10.4 Graphic Window ...................................................................................... 2-25
2.10.5 Data Window and Tabs............................................................................ 2-25
59056-02 A Page iii
2.10.6 Working Status Indicator.......................................................................... 2-25
2.11 Using the Topology Display.............................................................................. 2-26
2.11.1 Switch and Link Status ............................................................................ 2-26
2.11.2 Working with Switches and Links ............................................................ 2-27
2.11.2.1 Selecting Switches and Links ......................................................... 2-27
2.11.2.2 Arranging Switches in the Display .................................................. 2-27
2.11.2.3 Opening the Faceplate Display and Topology Popup Menus......... 2-28
2.11.3 Topology Data Windows.......................................................................... 2-28
2.12 Using the Faceplate Display............................................................................. 2-29
2.12.1 Port Views and Status ............................................................................. 2-30
2.12.2 Working with Ports...................................................................................2-30
2.12.2.1 Selecting Ports................................................................................2-30
2.12.2.2 Opening the Faceplate Popup Menu.............................................. 2-31
2.12.3 Faceplate Data Windows......................................................................... 2-31
0
Section 3 Managing Fabrics
3.1 Fabric Security ................................................................................................... 3-1
3.1.1 User Account Security............................................................................... 3-1
3.1.2 Fabric Services.......................................................................................... 3-2
3.1.2.1 Enabling SNMP Configuration.......................................................... 3-2
3.1.2.2 Enabling In-band Management ........................................................3-2
3.2 Fabric Tracker .................................................................................................... 3-3
3.2.1 Saving a Version Snapshot ....................................................................... 3-3
3.2.2 Viewing and Comparing Version Snapshots.............................................. 3-3
3.2.3 Exporting Version Snapshots to a File....................................................... 3-4
3.3 Managing the Fabric Database .......................................................................... 3-4
3.3.1 Adding a Fabric ......................................................................................... 3-5
3.3.2 Removing a Fabric .................................................................................... 3-6
3.3.3 Opening a Fabric View File ....................................................................... 3-6
3.3.4 Saving a Fabric View File.......................................................................... 3-6
3.3.5 Rediscovering a Fabric.............................................................................. 3-6
3.3.6 Deleting Switches and Links...................................................................... 3-7
3.3.7 Adding a New Switch to a Fabric............................................................... 3-7
3.3.8 Replacing a Failed Switch ......................................................................... 3-8
3.4 Displaying Fabric Information.............................................................................3-9
3.4.1 Fabric Status............................................................................................ 3-10
3.4.2 Displaying the Event Browser.................................................................. 3-11
3.4.2.1 Filtering the Event Browser ............................................................3-13
3.4.2.2 Sorting the Event Browser.............................................................. 3-14
3.4.2.3 Saving the Event Browser to a File ................................................ 3-14
Page iv 59056-02 A
SANbox 5200 Series Switch Management
0
3.4.3 Devices Data Window ............................................................................. 3-15
3.4.4 Active Zone Set Data Window................................................................. 3-16
3.4.5 Link Data Window.................................................................................... 3-17
3.5 Working with Device Information and Nicknames............................................ 3-17
3.5.1 Displaying Detailed Device Information................................................... 3-17
3.5.2 Exporting Device Information to a File..................................................... 3-18
3.5.3 Managing Device Port Nicknames .......................................................... 3-18
3.5.3.1 Creating a Nickname ...................................................................... 3-18
3.5.3.2 Editing a Nickname......................................................................... 3-19
3.5.3.3 Deleting a Nickname ...................................................................... 3-19
3.5.3.4 Exporting Nicknames to a File........................................................ 3-19
3.5.3.5 Importing a Nicknames File ............................................................ 3-20
3.6 Zoning a Fabric ................................................................................................ 3-20
3.6.1 Zoning Concepts ..................................................................................... 3-20
3.6.1.1 Zones.............................................................................................. 3-21
3.6.1.2 Aliases ............................................................................................ 3-22
3.6.1.3 Zone Sets ....................................................................................... 3-22
3.6.1.4 Zoning Database ............................................................................ 3-23
3.6.2 Using the Zoning Wizard ......................................................................... 3-24
3.6.3 Managing the Zoning Database .............................................................. 3-24
3.6.3.1 Editing the Zoning Database .......................................................... 3-25
3.6.3.2 Configuring the Zoning Database................................................... 3-28
3.6.3.3 Saving the Zoning Database to a File............................................. 3-29
3.6.3.4 Restoring the Zoning Database from a File.................................... 3-29
3.6.3.5 Restoring the Default Zoning Database..........................................3-30
3.6.3.6 Removing All Zoning Definitions..................................................... 3-30
3.6.4 Managing Zone Sets ............................................................................... 3-31
3.6.4.1 Creating a Zone Set .......................................................................3-31
3.6.4.2 Activating and Deactivating a Zone Set.......................................... 3-32
3.6.4.3 Copying a Zone to a Zone Set........................................................ 3-32
3.6.4.4 Removing a Zone from a Zone Set or from All Zone Sets.............. 3-32
3.6.4.5 Removing a Zone Set..................................................................... 3-33
3.6.5 Managing Zones...................................................................................... 3-33
3.6.5.1 Creating a Zone in a Zone Set .......................................................3-34
3.6.5.2 Adding Zone Members ................................................................... 3-35
3.6.5.3 Renaming a Zone or a Zone Set .................................................... 3-36
3.6.5.4 Removing a Zone Member ............................................................. 3-36
3.6.5.5 Removing a Zone from a Zone Set ................................................ 3-36
3.6.5.6 Removing a Zone from All Zone Sets............................................. 3-36
User’s Guide
59056-02 A Page v
3.6.5.7 Changing Zone Types .................................................................... 3-37
3.6.6 Managing Aliases .................................................................................... 3-37
3.6.6.1 Creating an Alias ............................................................................ 3-37
3.6.6.2 Adding a Member to an Alias ......................................................... 3-38
3.6.6.3 Removing an Alias from All Zones ................................................. 3-38
3.6.7 Merging Fabrics and Zoning.................................................................... 3-39
3.6.7.1 Zone Merge Failure ........................................................................ 3-39
3.6.7.2 Zone Merge Failure Recovery ........................................................ 3-40
0
Section 4 Managing Switches
4.1 Managing User Accounts ................................................................................... 4-2
4.1.1 Creating User Accounts............................................................................. 4-3
4.1.2 Removing a User Account.........................................................................4-4
4.1.3 Changing a User Account Password......................................................... 4-5
4.1.4 Modifying a User Account..........................................................................4-6
4.2 Displaying Switch Information ............................................................................ 4-7
4.2.1 Devices Data Window ............................................................................... 4-8
4.2.2 Switch Data Window.................................................................................. 4-8
4.2.3 Port Statistics Data Window .................................................................... 4-11
4.2.4 Port Information Data Window................................................................. 4-11
4.2.5 Configured Zonesets Data Windows....................................................... 4-12
4.3 Configuring Port Threshold Alarms .................................................................. 4-13
4.4 Paging a Switch................................................................................................ 4-14
4.5 Setting the Date/Time and Enabling NTP Client .............................................. 4-15
4.6 Resetting a Switch............................................................................................ 4-15
4.7 Configuring a Switch ........................................................................................ 4-17
4.7.1 Using the Configuration Wizard............................................................... 4-17
4.7.2 Switch Properties..................................................................................... 4-17
4.7.2.1 Symbolic Name .............................................................................. 4-18
4.7.2.2 Switch Administrative States........................................................... 4-18
4.7.2.3 Domain ID and Domain ID Lock ..................................................... 4-19
4.7.2.4 Fabric Device Management Interface............................................. 4-20
4.7.2.5 Broadcast Support.......................................................................... 4-21
4.7.2.6 In-band Management .....................................................................4-21
4.7.2.7 Interop Mode for Zoning ................................................................. 4-21
4.7.2.8 Legacy Port Address Format.......................................................... 4-22
4.7.2.9 Timeout Values ............................................................................... 4-22
4.7.3 Network Properties.................................................................................. 4-23
4.7.3.1 IP Configuration.............................................................................. 4-24
4.7.3.2 Remote Logging ............................................................................. 4-25
Page vi 59056-02 A
SANbox 5200 Series Switch Management
0
4.7.3.3 NTP Client ...................................................................................... 4-25
4.7.4 SNMP Properties..................................................................................... 4-26
4.7.4.1 SNMP Configuration....................................................................... 4-27
4.7.4.2 SNMP Trap Configuration...............................................................4-28
4.8 Archiving a Switch............................................................................................ 4-29
4.9 Restoring a Switch ........................................................................................... 4-29
4.10 Restoring the Factory Default Configuration .................................................... 4-31
4.11 Downloading a Support File ............................................................................. 4-33
4.12 Upgrading the Switch Using License Keys....................................................... 4-34
4.13 Installing Firmware ........................................................................................... 4-35
4.14 Displaying Hardware Status ............................................................................. 4-36
User’s Guide
Section 5 Managing Ports
5.1 Displaying Port Information ................................................................................ 5-1
5.1.1 Monitoring Port Status ............................................................................... 5-2
5.1.1.1 Displaying Port Types....................................................................... 5-2
5.1.1.2 Displaying Port Operational States................................................... 5-3
5.1.1.3 Displaying Port Speeds .................................................................... 5-3
5.1.1.4 Displaying Transceiver Media Status................................................ 5-4
5.1.2 Port Statistics Data Window ...................................................................... 5-5
5.1.3 Port Information Data Window...................................................................5-8
5.2 Configuring Ports.............................................................................................. 5-10
5.2.1 Changing Port Administrative States....................................................... 5-11
5.2.2 Changing Port Speeds ............................................................................ 5-12
5.2.3 Changing Port Types ............................................................................... 5-12
5.2.4 I/O Stream Guard .................................................................................... 5-13
5.2.5 Scan Device ............................................................................................ 5-13
5.2.6 Changing Port Symbolic Name ............................................................... 5-14
5.3 Using the Extended Credits Wizard ................................................................. 5-14
5.4 Resetting a Port................................................................................................ 5-15
5.5 Testing Ports..................................................................................................... 5-16
5.6 Graphing Port Performance ............................................................................. 5-18
5.6.1 Starting SANsurfer Performance Viewer ................................................. 5-19
5.6.2 Exiting SANsurfer Performance Viewer................................................... 5-19
5.6.3 Saving and Opening Performance View Files......................................... 5-20
5.6.4 Changing the Default Performance View File Encryption Key ................ 5-21
5.6.5 Setting SANsurfer Performance Viewer Preferences.............................. 5-21
5.6.6 Setting the Polling Frequency.................................................................. 5-22
5.6.7 Displaying Graphs ................................................................................... 5-22
5.6.7.1 Arranging Graphs in the Display..................................................... 5-23
59056-02 A Page vii
5.6.7.2 Customizing Graphs ....................................................................... 5-23
5.6.7.3 Rescaling a Selected Graph........................................................... 5-25
5.6.8 Printing Graphs........................................................................................5-25
5.6.9 Saving Graph Statistics to a File.............................................................. 5-25
0
Appendix A Command Line Interface
A.1 Logging On to a Switch ......................................................................................A-1
A.2 User Accounts....................................................................................................A-2
A.3 Working with Switch Configurations...................................................................A-3
A.3.1 Modifying a Configuration..........................................................................A-3
A.3.2 Backing up and Restoring Switch Configurations......................................A-4
A.4 Commands .........................................................................................................A-6
Admin Command.......................................................................................A-8
Alias Command .........................................................................................A-9
Config Command.....................................................................................A-11
Create Support Command.......................................................................A-14
Date Command .......................................................................................A-16
Feature Command...................................................................................A-17
Firmware Install Command......................................................................A-18
Hardreset Command ...............................................................................A-19
Help Command........................................................................................A-20
History Command....................................................................................A-21
Hotreset Command .................................................................................A-22
Image Command.....................................................................................A-23
Lip Command ..........................................................................................A-26
Passwd Command ..................................................................................A-27
Ping Command........................................................................................A-28
Ps Command...........................................................................................A-29
Quit Command ........................................................................................A-30
Reset Command......................................................................................A-31
Set Command..........................................................................................A-37
Set Config Command ..............................................................................A-39
Set Log Command...................................................................................A-51
Set Port Command..................................................................................A-54
Set Setup Command ...............................................................................A-56
Show Command......................................................................................A-61
Show Config Command...........................................................................A-76
Show Log Command...............................................................................A-80
Show Perf Command ..............................................................................A-83
Show Setup Command............................................................................A-86
Page viii 59056-02 A
SANbox 5200 Series Switch Management
0
Shutdown Command...............................................................................A-89
Test Command ........................................................................................A-90
Uptime Command....................................................................................A-93
User Command .......................................................................................A-94
Whoami Command..................................................................................A-97
Zone Command.......................................................................................A-98
Zoneset Command................................................................................A-102
Zoning Command..................................................................................A-104
User’s Guide
Glossary
Index

Figures

Figure Page
2-1 Initial Startup Dialog.......................................................................................................2-9
2-2 SANsurfer Switch Manager Window............................................................................ 2-10
2-3 Save Default Fabric View File Dialog...........................................................................2-11
2-4 Load Default Fabric File Dialog.................................................................................... 2-11
2-5 Preferences Dialog – SANsurfer Switch Manager ....................................................... 2-15
2-6 SANsurfer Switch Manager Display Elements............................................................. 2-17
2-7 Topology Display Menu................................................................................................2-18
2-8 Faceplate Display Menu............................................................................................... 2-19
2-9 Fabric Tree................................................................................................................... 2-24
2-10 Topology Display..........................................................................................................2-26
2-11 Faceplate Display......................................................................................................... 2-29
3-1 Fabric Version Snapshot Analysis Dialog ...................................................................... 3-4
3-2 Add a New Fabric Dialog ............................................................................................... 3-5
3-3 Events Browser............................................................................................................ 3-11
3-4 Filter Events Dialog...................................................................................................... 3-13
3-5 Active Zone Set Data Window ..................................................................................... 3-16
3-6 Detailed Devices Display Dialog .................................................................................. 3-17
3-7 Edit Zoning Dialog........................................................................................................ 3-25
3-8 Zoning Config Dialog....................................................................................................3-28
4-1 User Account Administration Dialog – Add Account ...................................................... 4-3
4-2 User Account Administration Dialog – Remove Account ............................................... 4-4
4-3 User Account Administration Dialog – Change Password ............................................. 4-5
4-4 User Account Administration Dialog - Modify Account................................................... 4-6
4-5 Faceplate Display - Switch Information..........................................................................4-7
4-6 Configured Zonesets Data Window ............................................................................. 4-12
4-7 Port Threshold Alarm Configuration Dialog.................................................................. 4-13
4-8 Port Threshold Alarm Example .................................................................................... 4-14
4-9 Switch Properties Dialog.............................................................................................. 4-18
4-10 Network Properties Dialog ........................................................................................... 4-23
59056-02 A Page ix
4-11 SNMP Properties Dialog .............................................................................................. 4-26
4-12 Restore Dialogs – Full and Selective ........................................................................... 4-30
4-13 Features License Key Dialog ....................................................................................... 4-34
4-14 Add License Key Dialog............................................................................................... 4-34
4-15 Hardware Status LEDs................................................................................................. 4-36
5-1 Faceplate Display – Port Information............................................................................. 5-1
5-2 Port Properties Dialog.................................................................................................. 5-10
5-3 Designate Donor Ports................................................................................................. 5-15
5-4 Port Loopback Test Dialog........................................................................................... 5-16
5-5 Fabric View Graphs...................................................................................................... 5-18
5-6 Save Default Performance View File Dialog ................................................................ 5-20
5-7 Load Default View File Dialog...................................................................................... 5-20
5-8 Preferences – SANsurfer Performance Viewer............................................................ 5-21
5-9 Default Graph Options Dialog ...................................................................................... 5-23
0
Page x 59056-02 A
SANbox 5200 Series Switch Management
0
User’s Guide

Tables

Table Page
2-1 Topology Display Menu Shortcut Keys ........................................................................ 2-20
2-2 Faceplate Display Shortcut Keys ................................................................................. 2-21
2-3 Tool Bar Buttons .......................................................................................................... 2-23
3-1 Topology Display Switch and Status Icons .................................................................. 3-10
3-2 Severity Levels............................................................................................................. 3-12
3-3 Devices Data Window Entries...................................................................................... 3-15
3-4 Edit Zoning Dialog Tool Bar Buttons and Icons ........................................................... 3-26
4-1 Factory User Accounts...................................................................................................4-2
4-2 Switch Data Window Entries.......................................................................................... 4-8
4-3 Switch Resets .............................................................................................................. 4-16
4-4 Switch Administrative States........................................................................................4-19
4-5 Timeout Values ............................................................................................................ 4-22
4-6 IP Configuration Parameters........................................................................................ 4-24
4-7 SNMP Configuration Parameters................................................................................. 4-27
4-8 SNMP Trap Configuration Parameters ........................................................................ 4-28
4-9 Factory Default Configuration Settings ........................................................................ 4-31
5-1 Port Types...................................................................................................................... 5-2
5-2 Port Operational States.................................................................................................. 5-3
5-3 Port Speeds ...................................................................................................................5-3
5-4 Port Transceiver Media View ......................................................................................... 5-4
5-5 Port Statistics Data Window Entries............................................................................... 5-5
5-6 Port Information Data Window Entries........................................................................... 5-8
5-7 Port Administrative States............................................................................................ 5-11
5-8 Port Speeds .................................................................................................................5-12
5-9 Port Types.................................................................................................................... 5-12
A-1 Command-Line Completion ...........................................................................................A-6
A-2 Commands Listed by Authority Level.............................................................................A-7
A-3 Switch Configuration Defaults ......................................................................................A-32
A-4 Port Configuration Defaults..........................................................................................A-33
A-5 Port Threshold Alarm Configuration Defaults...............................................................A-34
A-6 Zoning Configuration Defaults......................................................................................A-34
A-7 SNMP Configuration Defaults ......................................................................................A-35
A-8 System Configuration Defaults.....................................................................................A-36
A-9 Set Config Port Parameters .........................................................................................A-39
A-10 Set Config Switch Parameters .....................................................................................A-42
A-11 Set Config Threshold Parameters................................................................................A-45
A-12 Set Config Zoning Parameters.....................................................................................A-46
A-13 SNMP Configuration Settings ......................................................................................A-56
A-14 System Configuration Settings.....................................................................................A-57
A-15 Show Port Parameters.................................................................................................A-63
A-16 Switch Operational Parameters ...................................................................................A-66
A-17 Zoning Database Limits .............................................................................................A-105
59056-02 A Page xi
Notes
0
Page xii 59056-02 A
Section 1
Introduction
This manual describes the switch management tools which include the SANsurfer Switch Manager application (version 4.02) and the Command Line Interface (CLI) for the SANbox 5200 Series Fibre Channel switches (firmware version 4.2). This includes the model 5200 switch and the model 5202 switch with dual replaceable power supplies. The SANbox 5200 Series switches are 20 port non-blocking Fibre Channel switches. This manual defines the features, components, and performance characteristics of the SANbox 5200 Series switches. The SANsurfer Switch Manager application is the primary focus of this manual which is organized as follows:
Section 1 describes the intended audience for this manual, related
materials, and technical support.
Section 2 describes how to use SANsurfer Switch Manager, its menus, and
its displays.
Section 3 describes fabric management tasks.
Section 4 describes switch management tasks.
Section 5 describes port and device management tasks.
Appendix A describes the command line interface.
A glossary of terms and an index are also provided.
1.1

Intended Audience

This manual introduces the switch management products and explains their installation and use. It is intended for users responsible for installing and using switch management tools.
1.2

Related Materials

Refer to the following manuals for information about switch hardware and installation.
SANbox 5200 Series Fibre Channel Switch Installation Guide, publication
number 59055-02 Rev. A.
59056-02 A 1-1
1 – Introduction JDOM License
1.3

JDOM License

This product includes software developed by the JDOM Project (http://www.jdom.org/). Copyright (C) 2000-2002 Brett McLaughlin & Jason Hunter. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this
2. Redistributions in binary form must reproduce the above copyright notice,
3. The name "JDOM" must not be used to endorse or promote products
4. Products derived from this software may not be called "JDOM", nor may
0
list of conditions, and the following disclaimer.
this list of conditions, and the disclaimer that follows these conditions in the documentation and/or other materials provided with the distribution.
derived from this software without prior written permission. For written permission, please contact license@jdom.org.
"JDOM" appear in their name, without prior written permission from the JDOM Project Management (pm@jdom.org).
In addition, we request (but do not require) that you include in the end-user documentation provided with the redistribution and/or in the software itself an acknowledgement equivalent to the following: "This product includes software developed by the JDOM Project (http://www.jdom.org/)."
Alternatively, the acknowledgment may be graphical using the logos available at http://www.jdom.org/images/logos.
THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE JDOM AUTHORS OR THE PROJECT CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
This software consists of voluntary contributions made by many individuals on behalf of the JDOM Project and was originally created by Brett McLaughlin <brett@jdom.org> and Jason Hunter <jhunter@jdom.org>. For more information on the JDOM Project, please see <http://www.jdom.org/>.
1-2 59056-02 A
0
1.4

Technical Support

Customers should contact their authorized maintenance provider for technical support of their QLogic switch products. QLogic-direct customers may contact QLogic Technical Support; others will be redirected to their authorized maintenance provider.
Visit the QLogic support Web site listed in Contact Information for the latest firmware and software updates.
1.4.1

Availability

QLogic Technical Support is available from 7:00 AM to 7:00 PM Central Standard Time, Monday through Friday, excluding QLogic-observed holidays.
1.4.2

Training

QLogic offers certification training for the technical professional for both the SANblade™ HBAs and the SANbox 5200 Series switches. From the training link at www.qlogic.com, you may choose Electronic-Based Training or schedule an intensive "hands-on" Certification course.
1 – Introduction
Technical Support
Technical Certification courses include installation, maintenance and troubleshooting QLogic SAN products. Upon demonstrating knowledge using live equipment, QLogic awards a certificate identifying the student as a Certified Professional. The training professionals at QLogic may be reached by email at tech.training@qlogic.com
1.4.3

Contact Information

Telephone: +1 952-932-4040
Fax: +1 952-932-4018
Email: Technical Service Technical Training
QLogic Web Site: www.qlogic.com
Technical Support Web Site: support.qlogic.comt
support@qlogic.com tech.training@qlogic.com
59056-02 A 1-3
1 – Introduction Technical Support
Notes
0
1-4 59056-02 A
Section 2
Using SANsurfer Switch Manager
This section describes how to use the SANsurfer Switch Manager application and its menus. The following topics are covered:
Installing the Management Application
Starting SANsurfer Switch Manager
Exiting SANsurfer Switch Manager
Uninstalling SANsurfer Switch Manager
Changing the Encryption Key for the Default Fabric View File
Saving and Opening Fabric View Files
Setting SANsurfer Switch Manager Preferences
Using Online Help
Viewing Software Version and Copyright Information
SANsurfer Switch Manager User Interface
Using the Topology Display
Using the Faceplate Display
2.1

Installing the Management Application

You can manage the switch using SANsurfer Switch Manager as a standalone application or as a part of SANsurfer Management Suite™. SANsurfer Management Suite is QLogic’s integrated fabric management application, managing both HBAs and switches.
If your switch was shipped with a SANsurfer Switch Manager Disk, refer to
”SANsurfer Switch Manager” on page 2-2 for instructions on how to install
SANsurfer Switch Manager.
If your switch was shipped with a SANsurfer Management Suite Disk, refer
to ”SANsurfer Management Suite” on page 2-3 for instructions on how to install and upgrade SANsurfer Management Suite.
Refer to the SANbox 5200 Series Switch Management User’s Guide for more information about using, exiting, and uninstalling SANsurfer Management Suite and SANsurfer Switch Manager.
59056-02 A 2-1
2 – Using SANsurfer Switch Manager Installing the Management Application
2.1.1

SANsurfer Switch Manager

You can install SANsurfer Switch Manager on a Windows, Linux, or Solaris workstation. To install SANsurfer Switch Manager from the SANsurfer Switch Manager disk, close all programs currently running, and insert the SANsurfer Switch Manager Installation Disk into the management workstation CD-ROM drive.
For a Windows workstation:
1. Using Windows Explorer, double-click the drive letter which contains the SANsurfer Switch Manager Installation Disk.
2. Double click the Switch_Manager folder, then double click the Windows folder.
3. Double click the executable file and follow the SANsurfer Switch Manager installation instructions.
For a Linux workstation:
0
1. If a file browser does not open, double-click the CD-ROM icon to open the browser. Double click the Switch_Manager folder, then double click the Linux folder. If there is no CD-ROM icon, do the following:
a. Open an xterm or other terminal window.
b. Mount the CD-ROM. From a shell prompt, enter the following
command:
mount /mnt/cdrom
c. Change directory to location of the install program:
cd /mnt/cdrom/Switch_Manager/Linux
2. Enter the following command to make the install file executable:
chmod +x Linux_4.02.xx_xxxx.bin
3. Execute the install program and follow the installation instructions:
./Linux_4.02.xx_xxxx.bin
For a Solaris workstation:
1. Open a terminal window. If the disk isn’t already mounted, enter the following command:
volcheck
2. Move to the directory on the disk that contains the executable. Enter the following command:
cd /cdrom/cdrom0/Switch_Manager/solaris
2-2 59056-02 A
0
3. Add the package and follow the SANsurfer Switch Manager installation instructions. Enter the following command:
pkgadd -d sol_pkg
2.1.2

SANsurfer Management Suite

The following instructions describe how to install SANsurfer Management Suite and upgrade SANsurfer Switch Manager. You can install SANsurfer Management Suite (SMS) on a Windows, Linux, or Solaris workstation. Choose the instructions for your workstation:
SMS Installation for Windows
SMS Installation for Linux
SMS Installation for Solaris
2.1.2.1
SMS Installation for Windows
Close all programs currently running, and insert the SANsurfer Management Suite Installation Disk into the management workstation CD-ROM drive.
2 – Using SANsurfer Switch Manager
Installing the Management Application
1. If the SANsurfer Management Suite start page does not open in your default browser, do the following:
a. Using Windows Explorer, double-click the drive letter which contains
the SANsurfer Management Suite Disk.
b. Locate and double-click the Start_Here.htm file to open the SANsurfer
Management Suite start page in your default browser.
2. On the SANsurfer Management Suite start page, click the SANbox Switch Software button.
3. On the SANbox Switch Software page, scroll to the SANbox 5200 Series Series area.
4. In the Operating System column, click the Win NT/2000 link.
5. Click the SANsurfer Management Software link to open the File Download dialog.
6. You can run the installation file from the CD-ROM or download the installation file to your hard drive. Choose one of the following:
Open the installation file from the CD-ROM and follow the SANsurfer
Switch Manager installation instructions.
Specify a location in which to save the
sansurfer_windows_install.exe file, and click the Save button. Double-click the saved sansurfer_windows_install.exe file and follow the installation instructions.
59056-02 A 2-3
2 – Using SANsurfer Switch Manager Installing the Management Application
7. When the installation is complete, start SANsurfer Management Suite using the SANsurfer file from the SANsurfer Management Suite installation directory. You can also start SANsurfer Management Suite by clicking the SANsurfer icon (if installed) on the desktop or from the Start menu. In SMS, Click the Switch tab in the left pane. From the Help menu, select About ... and make note of the version number. Close SANsurfer Management Suite.
8. To ensure you are using the most recent version of SANsurfer Switch Manager, visit the QLogic support web page and go to Drivers, Software and
Manuals.
a. Select your switch model from the pull-down menu. Locate the
description for SANsurfer Switch Manager for Windows under "Management Software".
b. If the release version number (4.02.xx) is greater than what is currently
installed, download the new version and proceed to step 9. Otherwise, no upgrade is needed and the SMS installation is complete.
9. To start the installer, open the zip file and run the SANsurferSwitchMgr_Windows_4.02.xx.exe file.
0
10. When prompted for an installation directory, click the Choose button and select the same folder as the SANsurfer Management Suite installation in
step 6. The default SMS installation directory is C:\Program Files\QLogic
Corporation\SANsurfer. Click the Next button.
11. When prompted for the location in which to create the program icons, click the In an Existing Group radio button, then specify the same group that was used for the SMS installation. The default SMS group is "QLogic Management Suite". Click the Next button.
12. Click the Install button to the start the installation. When the installation is complete, click the Done button.
13. In the SMS install directory, enter the following command to execute the chglax.bat file. If prompted to overwrite an existing file, enter Y to do so.
chglax.bat
14. Restart SANsurfer Switch Manager from SANsurfer Management suite as you did in step 7 and confirm that the new version is running.
2-4 59056-02 A
0
2.1.2.2
SMS Installation for Linux
Close all programs currently running, and insert the SANsurfer Management Suite Installation Disk into the management workstation CD-ROM drive.
1. If a file browser dialog opens showing icons for the contents of the CD-ROM, double-click the Start_Here.htm file to open the SANsurfer Management Suite start page. If a file browser does not open, double-click the CD-ROM icon to open the browser. If there is no CD-ROM icon, do the following:
a. Open an xterm or other terminal window.
b. Mount the CD-ROM. From a shell prompt, enter the following
command:
mount /mnt/cdrom
c. Execute your web browser to view the Start_Here.htm document
using one of the following commands:
mozilla file:/mnt/cdrom/Start_Here.htm
2 – Using SANsurfer Switch Manager
Installing the Management Application
or
netscape file:/mnt/cdrom/Start_Here.htm
d. The SANsurfer Management Suite start page opens in your browser.
2. On the SANsurfer Management Suite start page, click the SANbox Switch Software button.
3. On the SANbox Switch Software page, scroll to the SANbox 5200 Series Series area.
4. In the Operating System column, click the Linux link.
5. Click the SANsurfer Management Software link to open the File Download dialog.
6. Enter a path name to save the sansurfer_linux_install.bin file, and click the Save button.
7. Open a terminal window for the directory in which the sansurfer_linux_install.bin file was saved, and make the file executable.
chmod +x sansurfer_linux_install.bin
8. Execute the install program and follow the installation instructions
./sansurfer_linux_install.bin
9. When the installation is complete, start SANsurfer Management Suite using the SANsurfer file in the installation directory. Click the Switch tab from the left pane to open SANsurfer Switch Manager. From the Help menu, select About ... and make note of the release version number. Close SANsurfer Management Suite.
59056-02 A 2-5
2 – Using SANsurfer Switch Manager Installing the Management Application
10. To ensure that you are using the most recent version of SANsurfer Switch Manager, visit the QLogic support web page and go to Drivers, Software and
Manuals.
a. Select your switch model from the pull-down menu. Locate the
description for SANsurfer Switch Manager for Linux under "Management Software".
b. If the release version number (4.02.xx) is greater than what is currently
installed on your workstation, down load the new version and proceed to step 11. Otherwise, no upgrade is needed and the SMS installation is complete.
11. From the tar.gz file, extract the SANsurferSwitchMgr_Linux_4.02.xx.bin file and make the file executable.
chmod +x sansurferswitchmgr_linux_4.02.xx.bin
12. Execute the install program and follow the installation instructions.
./sansurferswitchmgr_linux_4.02.xx.bin
13. When prompted for an installation directory, click the Choose button and select the same folder as the SANsurfer Management Suite installation in
step 9. The default SMS installation directory is
/opt/QLogic_Corporation/SANsurfer.
0
14. Enter the following script command from the installation directory:
./chglax
15. Start SANsurfer Switch Manager from SANsurfer Management suite as you did in step 9 and confirm that the new version is running.
2.1.2.3
SMS Installation for Solaris
To install the SANsurfer Switch Manager application on Solaris from the SANsurfer Management Suite CD-ROM, do the following:
1. Insert the SANsurfer Management Suite Disk into the management workstation CD-ROM drive. If the SANsurfer Management Suite start page does not open in your default browser, do the following:
a. Right-click the Workspace Menu.
b. Select File, then select File Manager.
c. In File Manager, double-click the CD-ROM folder, and then
double-click the Sansurfer folder.
d. In the Sansurfer folder, double-click the Start_Here.htm file to open
the SANsurfer Management Suite start page in your default browser.
2. On the SANsurfer Management Suite start page, click the SANbox Switch Software button.
2-6 59056-02 A
0
2 – Using SANsurfer Switch Manager
Installing the Management Application
3. On the SANbox Switch Software page, scroll to the SANbox 5200 Series Series area.
4. In the Operating System column, click the Solaris SPARC link.
5. Click the SANsurfer Management Software link to open the Save As dialog.
6. Enter a path name to save the sansurfer_solaris_install.bin file and click the Save button.
7. Open a terminal window for the directory in which the sansurfer_solaris_install.bin file was saved, and enter the following:
chmod +x sansurfer_solaris_install.bin
8. Execute the install program and follow the installation instructions:
./sansurfer_solaris_install.bin
9. When the installation is complete, start SANsurfer Management Suite using the SANsurfer file in the installation directory. Click the Switch tab from the left pane to open SANsurfer Switch Manager. From the Help menu, select About ... and make note of the release version number. Close SANsurfer Management Suite.
10. To ensure that you are using the most recent version of SANsurfer Switch Manager, visit the QLogic support web page and go to Drivers, Software and
Manuals.
a. Select your switch model from the pull-down menu. Locate the
description for SANsurfer Switch Manager for Linux under "Management Software".
b. If the release version number (4.02.xx) is greater than what is currently
installed on your workstation, down load the new version. Otherwise, no upgrade is needed.
11. Open the tar file and save the SANsurferSwitchMgr_QLGCsol_4.02.xx.bin file in a folder and make the file executable.
# chmod +x sansurferswitchmgr_QLGCsol_4.02.xx
12. Install the new SANsurfer Switch Manager package:
# pkgadd -d sansurferswitchmgr_QLGCsol_4.02.xx
13. Change directories to the package location:
# cd /usr/opt/QLGCsol/bin
14. Locate and execute the file sbm_over_sms.sh:
# ./sbm_over_sms.sh
59056-02 A 2-7
2 – Using SANsurfer Switch Manager Starting SANsurfer Switch Manager
15. When prompted for the SMS installation directory, enter d if SMS was installed in it’s default directory (/opt/QLogic_Corporation/SANsurfer). Otherwise, enter the path name for the SMS installation directory. The script will copy the necessary files to the specified installation directory.
16. Restart SANsurfer Switch Manager from SANsurfer Management suite as you did in step 9 and confirm that the new version is running.
2.2

Starting SANsurfer Switch Manager

You can start SANsurfer Switch Manager as a standalone application or from SANsurfer Management Suite.
Note: After the switch is operational, you can also open the SANsurfer
Switch Manager web applet, by entering the switch IP address in an internet browser. If your workstation does not have the Java 2 Run Time Environment program, you will be prompted to download it.
0
To start SANsurfer Switch Manager as a standalone application, do the
following.
1. Start the SANsurfer Switch Manager using one of the following
methods:
For Windows, double-click the SANsurfer Switch Manager
shortcut, or select SANsurfer Switch Manager from Start menu, depending on how you installed the SANsurfer Switch Manager application. From a command line, you can enter the SANsurfer_Switch_Manager command:
<install_directory>SANsurfer_Switch_Manager.exe
For Linux or Solaris, enter the SANsurfer_Switch_Manager
command:
<install_directory>./SANsurfer_Switch_Manager
2. In the Initial Start dialog, click the Open Configuration Wizard button.
When you power up the switch, the Configuration Wizard will recognize the switch and lead you through the configuration process.
2-8 59056-02 A
0
2 – Using SANsurfer Switch Manager
Starting SANsurfer Switch Manager
To start SANsurfer Switch Manager from SANsurfer Management Suite, do
the following.
1. Start the SANsurfer Management Suite application using one of the
following methods:
For Windows, double-click the SANsurfer shortcut, or select
SANsurfer from Start menu, depending on how you installed the SANsurfer application. From a command line, enter the following command:
<install_directory>\SANsurfer.exe
For Linux or Solaris enter the SANsurfer command:
<install_directory>./SANsurfer
2. From the SANsurfer Management Suite home page, click the
SANsurfer Switch Manager button.
3. In the Initial Start dialog, click the Open Configuration Wizard button.
When you power up the switch, the Configuration Wizard will recognize the switch and lead you through the configuration process.
The application opens with the Initial Start dialog shown in Figure 2-1. If you prefer not to see this dialog, check the Don’t show this dialog again box. This has the same effect as disabling the Display Initial Startup Dialog preference. Refer to
”Setting SANsurfer Switch Manager Preferences” on page 2-14 for information
about setting preferences.
Figure 2-1. Initial Startup Dialog
59056-02 A 2-9
2 – Using SANsurfer Switch Manager Exiting SANsurfer Switch Manager
Click the Open Existing Fabric radio button to open the Add a New Fabric
dialog, which prompts you for a fabric name, IP address, account name, and password. Refer to ”Adding a Fabric” on page 3-5.
Click the Open Existing Fabric View File radio button to open the Open
View dialog which prompts you to specify a fabric view file that you saved earlier. Refer to ”Opening a Fabric View File” on page 3-6.
Click the Start Application Without Specifying a Fabric radio button to
open the SANsurfer Switch Manager window shown in Figure 2-2.
Click the Open Configuration Wizard radio button to open the Config
Wizard to configure a switch, add a new switch, replace/restore a switch, or recover or edit an IP configuration of an existing switch.
0
Figure 2-2. SANsurfer Switch Manager Window
2.3

Exiting SANsurfer Switch Manager

To exit a SANsurfer Switch Manager application session, open the File menu and select Exit. If you have not yet defined an encryption key, the Save Default Fabric View File dialog, shown in Figure 2-3, prompts you to save the current fabric view as the default fabric view file. Enter an encryption key in the Default Fabric File Encryption Key field. Re-enter the encryption key in the Re-enter Encryption Key to Confirm field. Click the OK button to save the current set of fabrics to the default fabric view file in the working directory.
2-10 59056-02 A
0
2 – Using SANsurfer Switch Manager
Exiting SANsurfer Switch Manager
Figure 2-3. Save Default Fabric View File Dialog
The encryption key is used to encrypt the sensitive data in the default fabric view file. Refer to ”Changing the Encryption Key for the Default Fabric View File” on
page 2-13 for information about changing this encryption key. If an encryption key
has been defined and the View File Auto Save and Load preferences settings are set to Enable, the current fabric view is automatically saved to your default fabric view file upon exit future SANsurfer Switch Manager sessions.
To prevent SANsurfer Switch Manager from prompting you to save the default fabric view file between SANsurfer Switch Manager sessions, set the View File Auto Save and Load preferences setting to Enable (default). Refer to ”Setting
SANsurfer Switch Manager Preferences” on page 2-14 for more information.
In your next SANsurfer Switch Manager session, the Load Default Fabric File dialog shown in Figure 2-4 prompts you to load the default fabric view file and to specify its encryption key, if there is one. In the Default Fabric File Encryption Key field, enter the encryption key and click the Load View File button. If you do not want to load the default fabric view file, click the Continue Without Loading button to open the SANsurfer Switch Manager with no fabric displayed.
Figure 2-4. Load Default Fabric File Dialog
59056-02 A 2-11
2 – Using SANsurfer Switch Manager Uninstalling SANsurfer Switch Manager
2.4

Uninstalling SANsurfer Switch Manager

The method you use to uninstall SANsurfer Switch Manager depends on how you installed it:
If you installed SANsurfer Switch Manager as part of SANsurfer
Management Suite, you must uninstall SANsurfer Management Suite. Refer to ”SMS Uninstall” on page 2-12.
If you installed SANsurfer Switch Manager as a standalone program, you
must uninstall SANsurfer Switch Manager directly. Refer to ”Standalone
Uninstall” on page 2-13.
2.4.1

SMS Uninstall

A program to uninstall SANsurfer Management Suite was included as part of the SANsurfer Management Suite installation process. Use this method only if you installed SANsurfer Switch Manager as part of SANsurfer Management Suite. The UninstallData folder in the installation directory contains the uninstall program, SANsurferUninstaller.
0
The default installation directories are:
For Windows: C:\Program Files\QLogic_Corporation\SANsurfer
For Linux: /opt/QLogic_Corporation/SANsurfer
For Solaris: /opt/QLogic_Corporation/SANsurfer
To uninstall the SANsurfer Management Suite application, do the following:
For Windows, browse for the uninstall program file or the shortcut/link that
points to the uninstall program file. The uninstall program shortcut is in the same folder as the program shortcut (Start menu, program group, on desktop, or user specified) that is used to start the SANsurfer Management Suite application. Double-click the uninstall program file or shortcut/link, and follow the instructions.
For Linux, execute the link to SANsurferUninstaller.
<install_directory>/UninstallerData/SANsurferUninstaller
For Solaris, enter the following command and follow the instructions:
<install_directory>/UninstallData/SANsurferUninstaller
2-12 59056-02 A
0
2.4.2

Standalone Uninstall

A program to uninstall SANsurfer Switch Manager was included as part of the SANsurfer Switch Manager installation process. Use this method only if you installed SANsurfer Switch Manager as a standalone program. The UninstallerData folder in the Install directory contains the uninstall program, Uninstall Switch_Manager. Also, a shortcut/link to the uninstall program was installed in the installation directory during the SANsurfer Switch Manager installation process.
The default installation directories are:
For Windows: C:\Program Files\QLogic_Corporation\Switch_Manager
For Linux: /opt/QLogic_Corporation/Switch_Manager
For Solaris: /usr/opt/QLGCsol
To uninstall the SANsurfer Switch Manager application, do the following:
For Windows, browse for the uninstall program file or the shortcut/link that
points to the uninstall program file. The uninstall program shortcut is in the same folder as the program shortcut (Start menu, program group, on desktop, or user specified) that is used to start the SANsurfer Switch Manager application. Double-click the uninstall program file or shortcut/link, and follow the instructions to uninstall the SANsurfer Switch Manager application.
2 – Using SANsurfer Switch Manager

Changing the Encryption Key for the Default Fabric View File

For Linux, execute the link to Uninstall_Switch_Manager. If no links were
created during the installation, enter the following command:
<install_directory>UninstallerData/Uninstall_Switch_Manager
For Solaris, enter the following command and follow the instructions to
uninstall the SANsurfer Switch Manager application:
pkgrm QLGCsol
2.5
Changing the Encryption Key for the Default Fabric View File
To change the encryption key for the SANsurfer Switch Manager default fabric view file, do the following:
1. Open the File menu and select Save Default Fabric View File to open the Save Default Fabric View File dialog. Enter an encryption key in the Default Fabric File Encryption Key field.
2. Re-enter the same encryption key in the Re-enter Encryption Key to Confirm field.
3. Click the OK button to save the current set of fabrics to the default fabric view file in the working directory.
59056-02 A 2-13
2 – Using SANsurfer Switch Manager Saving and Opening Fabric View Files
2.6

Saving and Opening Fabric View Files

A fabric view file is one or more fabrics saved to a file. In addition to the SANsurfer Switch Manager default fabric view file, you can save and open your own fabric view files. To save a set of fabrics to a file, do the following:
1. Open the File menu and select Save View As to open the Save View dialog.
2. Enter a name for the fabric view file or click the Browse button to select an existing file. Files are saved in the working directory.
3. Enter a password. When you attempt to open this fabric view file, you will be prompted for this password. If you leave the File Password field blank, no password will be required when attempting to open this fabric view file.
4. Click the OK button to save the view.
To open a fabric view file, do the following:
1. Open the File menu and select Open View File to open the Open View dialog.
0
2. Enter a name for the fabric view file or click the Browse button to select an existing file.
3. If the fabric view file was saved with a password, enter the password and click the OK button.
4. Click the OK button to open the view.
2.7

Setting SANsurfer Switch Manager Preferences

Using the preferences settings, you can:
Change the location of the working directory in which to save files.
Change the location of the browser used to view the online help.
Choose the fabric discovery interval. The fabric discovery interval is how
often the SANsurfer Switch Manager application receives information from the fabric. Choose 30 (default), 45, or 60 seconds. The smaller the interval, the more often the application talks to the switch and thus the greater impact to performance.
Enable (default) or disable the view file auto save and load feature. Refer to
”Exiting SANsurfer Switch Manager” on page 2-10 for more information on
the default fabric view file.
Enable (default) or disable the use of the Initial Start Dialog at the beginning
of a SANsurfer Switch Manager session. Refer to ”Starting SANsurfer
Switch Manager” on page 2-8 for information about the Initial Start Dialog.
After a default fabric view file is created, this setting has no effect.
2-14 59056-02 A
0
2 – Using SANsurfer Switch Manager
Setting SANsurfer Switch Manager Preferences
Enable (default) or disable the Event Browser. Refer to ”Displaying the
Event Browser” on page 3-11. If the Event Browser is enabled using the
Preferences dialog as shown in Figure 2-5, the next time SANsurfer Switch Manager is started, all events will be displayed. If the Event Browser is disabled when SANsurfer Switch Manager is started and later enabled, only those events from the time the Event Browser was enabled and forward will be displayed.
Choose the default port view when opening the faceplate display. You can
set the faceplate to reflect the current port type (default), port speed, port operational state, or port transceiver media. Regardless of the default port view you choose, you can change the port view in the faceplate display by opening the View menu and selecting a different port view option. Refer to the corresponding subsection for more information:
”Port Types” on page 5-2
”Displaying Port Operational States” on page 5-3
”Displaying Port Speeds” on page 5-3
”Displaying Transceiver Media Status” on page 5-4
Figure 2-5. Preferences Dialog – SANsurfer Switch Manager
To set preferences for your SANsurfer Switch Manager sessions, do the following:
1. Open the File menu, and select Preferences to open the Preferences dialog.
2. Enter, or browse, for paths to the working directory and browser.
3. In the Application-wide Options area, choose the preferences you want.
4. Click the OK button to save the changes.
59056-02 A 2-15
2 – Using SANsurfer Switch Manager Using Online Help
2.8

Using Online Help

Online help is available for the SANsurfer Switch Manager application and its functions. The two ways to open the online help file are: open the Help menu and select Help Topics, or click the Help button in the tool bar. You can also display context-sensitive help for all SANsurfer Switch Manager dialogs by choosing the Help button in the dialog.
2.9

Viewing Software Version and Copyright Information

To view SANsurfer Switch Manager software version and copyright information,
open the Help menu and select About....
0
2-16 59056-02 A
0
2.10

SANsurfer Switch Manager User Interface

The SANsurfer Switch Manager application uses two basic displays to manage the fabric and individual switches: the topology display and the faceplate display. The topology display shows all switches that are able to communicate and all connections between switches. The faceplate display shows the front of a single switch and its ports. Both displays share some common elements as shown in
Figure 2-6.
2 – Using SANsurfer Switch Manager
SANsurfer Switch Manager User Interface
Topology
Display
Fabric
Tree
Faceplate
Display
Menu
Bar
Data Window Tabs
Tool Bar
Graphic Window
Data
Window
Working Status Indicator
Figure 2-6. SANsurfer Switch Manager Display Elements
59056-02 A 2-17
2 – Using SANsurfer Switch Manager SANsurfer Switch Manager User Interface
2.10.1

Menu Bars

The menus and the options offered in them vary depending on the display. For example, the Port menu and many of the Switch menu selections are available only in the faceplate display.
2.10.1.1
Topology Display Menu
The menu options available in the topology display are shown in Figure 2-7.
0
Figure 2-7. Topology Display Menu
2-18 59056-02 A
0
2.10.1.2
Faceplate Display Menu
The menu options available in the faceplate display are shown in Figure 2-8.
2 – Using SANsurfer Switch Manager
SANsurfer Switch Manager User Interface
Figure 2-8. Faceplate Display Menu
The keyboard shortcut keys vary by display type: topology display and faceplate display. In addition to the menu bar, both the topology and faceplate displays have context sensitive menus that pop up when you right-click in the graphic window. Refer to ”Opening the Faceplate Display and Topology Popup Menus” on
page 2-28 for more information about these popup menus.
59056-02 A 2-19
2 – Using SANsurfer Switch Manager SANsurfer Switch Manager User Interface
2.10.1.3
Topology Display Shortcut Keys
The shortcut keys for the topology display are shown in Table 2-1. The shortcut key combinations are not case-sensitive.
Table 2-1. Topology Display Menu Shortcut Keys
Shortcut Selection Shortcut Selection
0
Ctrl+O Alt+F, O
Alt+F, A File>Save View As Alt+S, E Switch>Export Devices
Alt+F, D File>Save Default Fabric
Alt+F, R File>Preferences Alt+S, N Switch>Network Properties
Alt+F, N File>Nicknames Alt+S, S Switch>SNMP Properties
Alt+F, X File>Exit Alt+W, C Wizards> Configuration Wizard
Alt+B, A Fabric>Add Fabric Alt+V, RF5View>Refresh
Alt+B, R Fabric>Remove Fabric Alt+V, L View>Layout Topology
Alt+B, F +S +A
File>Open View File Alt+S, D Switch>Delete
Information
Alt+S, P Switch>Switch Properties
View File
Fabric>FabricTracker Save Snapshot Analyze Snapshot
Alt+V, A View>Toggle Auto Layout
(active only when one switch is selected)
(active only when one switch is selected)
(active only when one switch is selected)
Alt+B, D Fabric>Rediscover Fabric Alt+V, M View>Remember Layout
Alt+B, T Fabric>Start Performance
Viewer
Alt+B, E Fabric>Show Event Browser Alt+H, A Help>About
2-20 59056-02 A
Alt+H, H Help>Help Topics
0
2.10.1.4
Faceplate Display Shortcut Keys
The shortcut keys for the faceplate display are shown in Table 2-2. The shortcut key combinations are not case-sensitive.
Table 2-2. Faceplate Display Shortcut Keys
Shortcut Selection Shortcut Selection
2 – Using SANsurfer Switch Manager
SANsurfer Switch Manager User Interface
Ctrl+O Alt+F, O
Alt+F, A File>Save View As Alt+S, W Switch>Download Support File
Alt+F, D File>Save Default Fabric
Alt+F, R File>Preferences Alt+P, 0
Alt+F, N File>Nicknames Alt+P, N Port>Port Symbolic Name
Alt+F, X File>Exit Alt+P, T Port>Reset Port
Alt+B, A Fabric>Add Fabric Alt+P, L Port>Port Loopback Test
Alt+B, R Fabric>Remove Fabric Alt+Z, E Zoning>Edit Zoning
Alt+B, F +S +A
Alt+B, E Fabric>Show Event Browser Alt+Z, A Zoning>Activate Zone Set
Alt+S, A Switch>Archive Alt+Z, D Zoning>Deactivate Zone Set
Alt+S, R Switch>Restore Alt+Z, R Zoning>Restore Default Zoning
File>Open View File Alt+S, T Switch>Features
Alt+P, 2 Port>Port Properties
View File
Port>Port Properties 10G
(zero)
Fabric>FabricTracker Save Snapshot Analyze Snapshot
Alt+Z, C Zoning>Edit Zoning Config
Alt+S, U Switch>User Accounts Alt+W, C Wizards>Configuration Wizard
Alt+S, D Switch>Set Date/Time Alt+W, E Wizards>Ext Credit Wizard
Alt+S, P Switch>Switch Properties Alt+W, Z Wizards>Zoning Wizard
Alt+S, N Switch>Network Properties Alt+V, RF5View>Refresh
Alt+S, S Switch>SNMP Properties Alt+V, T View>View Port Types
Alt+S, G Switch>Toggle Beacon Alt+V, S View>View Port States
Alt+S, C Switch>Port Threshold
Alarm Configuration
59056-02 A 2-21
Alt+V, E View>View Port Speeds
2 – Using SANsurfer Switch Manager SANsurfer Switch Manager User Interface
Table 2-2. Faceplate Display Shortcut Keys (Continued)
Shortcut Selection Shortcut Selection
Alt+S, L Switch>Load Firmware Alt+V, M View>View Port Media
0
Alt+S, E +R +H +A
Alt+S, Y Switch>Restore Factory
Switch>Reset Switch Reset Hot reset Hard Reset
Defaults
Alt+H, H Help>Help Topics
Alt+H, A Help>About
2-22 59056-02 A
0
2.10.2

Tool Bar

2 – Using SANsurfer Switch Manager
SANsurfer Switch Manager User Interface
The tool bar consists of a row of graphical buttons that you can use to access SANsurfer Switch Manager functions as shown in Table 2-3. The tool bar buttons are an alternative method to using the menu bar. The tool bar can be relocated in the display by clicking and dragging the handle at the left edge of the tool bar.
Table 2-3. Tool Bar Buttons
Tool Bar Button Description
Add Fabric button - adds a new fabric to the fabric view.
Open View File button - opens an existing fabric view file.
Save View As button - saves the current fabric view to a file.
Refresh button - updates the topology or faceplate display with current information.
Event Browser button - opens the events browser.
Edit Zoning button - opens the Edit Zoning dialog (available only in faceplate display).
Help Topics button - opens the online help file.
The QLogic logo opens a link to the QLogic web site.
59056-02 A 2-23
2 – Using SANsurfer Switch Manager SANsurfer Switch Manager User Interface
2.10.3

Fabric Tree

The fabric tree lists the managed fabrics and their switches as shown in
Figure 2-9. The window width can be adjusted by clicking and dragging the
moveable window border. An entry handle located to the left of an entry in the tree indicates that the entry can be expanded or collapsed. Click this handle or double-click the entry to expand or collapse a fabric tree entry. A fabric entry expands to show its member switches.
Fabric
Entry
0
Entry Handle
Switch
Entries
Moveable
Window Border
Figure 2-9. Fabric Tree
Each fabric tree entry has a small icon next to it that uses color to indicate operational status.
A green icon indicates normal operation.
A yellow icon indicates that a switch is operational, but may require attention
to maintain maximum performance.
A red icon indicates a potential failure or non-operational state (if switch is
offline).
A blue icon indicates that a switch is unknown, unreachable, or
unmanageable.
If the status of the fabric is not normal, the fabric icon in the fabric tree will indicate the reason for the abnormal status. The same message is provided when you rest the mouse over the fabric icon in the fabric tree.
2-24 59056-02 A
0
The fabric tree provides access to the topology and faceplate displays for any fabric or switch.
To open the topology display from the fabric tree, click a fabric entry.
To open the faceplate display from the fabric tree, click a switch entry.
2.10.4

Graphic Window

The graphic window, as shown in Figure 2-6, presents graphic information about fabrics and switches such as the fabric topology and the switch faceplate. The window height can be adjusted by clicking and dragging the window border that it shares with the data window. This only works when displaying a fabric.
2.10.5

Data Window and Tabs

The data window presents a table of data and statistics associated with the selected tab. Use the scroll bar to browse through the data. The window length can be adjusted by clicking and dragging the border that it shares with the graphic window.
2 – Using SANsurfer Switch Manager
SANsurfer Switch Manager User Interface
Adjust the column width by moving the pointer over the column heading border shared by two columns until a right/left arrow graphic is displayed. Click and drag the arrow to the desired width.
The data window tabs present options for the type of information to display in the data window. These options vary depending on the display.
2.10.6

Working Status Indicator

The working status indicator, located in the lower right corner of the SANsurfer Switch Manager window, shows when the management workstation is exchanging information with the fabric. As conditions change, the fabric forwards this information to the management workstation where it is reflected in the various displays.
59056-02 A 2-25
2 – Using SANsurfer Switch Manager Using the Topology Display
2.11

Using the Topology Display

The topology display shown in Figure 2-10 receives information from the selected fabric and displays its topology. Switches and inter-switch links (ISLs) appear in the graphic window and use color to indicate status. Consider the following topology display features:
Switch and link status
Working with switches and links
Topology data windows
0
Figure 2-10. Topology Display
2.11.1

Switch and Link Status

Switch icon shape and color provide information about the switch and its operational state. Lines represent links between switches. The topology display uses green to indicate normal operation, yellow to indicate operational with errors, red to indicate a potential failure or non-operational state, and blue to indicate unknown, unreachable, or unmanageable. Refer to ”Fabric Status” on page 3-10 for more information about topology display icons.
2-26 59056-02 A
0
2.11.2

Working with Switches and Links

Switch and link icons are selectable and moveable, and serve as access points for other displays and menus. You select switches and links to display information about them, modify their configuration, or delete them from the display. Context-sensitive popup menus are displayed when you right-click on a switch or link icon, or in the background of the topology display graphic window.
2.11.2.1
Selecting Switches and Links
Selected switch icons are highlighted in light blue. Selected ISLs are displayed as a heavier line. You can select switches and links in the following ways:
To select a switch or a link, click the icon or link.
To select multiple switches or links, hold down the Control key and select.
To select all switches or links, right-click anywhere in the graphic window
background. Select Select All Switches or Select All Links from the popup menu.
2 – Using SANsurfer Switch Manager
Using the Topology Display
To cancel a selection, press and hold the Control key, and select the item again. To cancel all selections, click in the graphic window background.
2.11.2.2
Arranging Switches in the Display
You can arrange individual switch icons in the topology display or allow SANsurfer Switch Manager to arrange all switch icons for you:
To move an individual switch icon, click and drag the icon to another location
in the graphic window. Links stretch or contract to remain connected.
To arrange all switch icons in the topology display automatically, open the
View menu and select Layout Topology.
By default, the Toggle Auto Layout box in the View menu is checked which causes SANsurfer Switch Manager to arrange the icons when you select Layout Topology.
You can save a custom arrangement, or layout, and restore that layout during a SANsurfer Switch Manager session. Begin by arranging the icons, then open the View menu and select Remember Layout. To restore the saved layout, open the View menu, uncheck the Toggle Auto Layout box, and select Layout Topology.
59056-02 A 2-27
2 – Using SANsurfer Switch Manager Using the Topology Display
2.11.2.3
Opening the Faceplate Display and Topology Popup Menus
The faceplate display shows the front of a single switch and its ports. To open the faceplate display when viewing the topology display, click the switch entry/icon in the fabric tree, or double-click the switch graphic.
The topology display also offers a fabric, switch, and a link popup menu:
To open the fabric popup menu, right-click the graphic window background.
The fabric popup menu presents selections to refresh the fabric, select all switches, select all links, or layout topology.
To open the switch popup menu, right-click the switch icon in the graphic
window. The switch popup menu presents selections to refresh the switch, delete the switch from the display, open the Switch Properties dialog, open the Network Properties dialog, and open the SNMP Properties dialog.
To open the link popup menu, right-click the link. The Link popup menu
presents a selection to delete the link from the display.
0
2.11.3

Topology Data Windows

The topology display provides the following data windows corresponding to the data window tabs:
Devices – displays information about devices (hosts and storage targets)
connected to the switch. Refer to ”Devices Data Window” on page 3-15 for more information.
Active Zoneset – displays the active zone set for the fabric including zones
and their member ports. Refer to ”Active Zone Set Data Window” on
page 3-16 for more information about this data window. Refer to ”Zoning a Fabric” on page 3-20 for information about zone sets and zones.
Switch – displays current network and switch configuration data for the
selected switches. Refer to ”Switch Data Window” on page 4-8 for more information.
Link – displays information about the inter-switch links. Refer to ”Link Data
Window” on page 3-17 to for more information.
2-28 59056-02 A
0
2.12

Using the Faceplate Display

The faceplate display shown in Figure 2-11 displays the switch name and operational state, and port status. Consider the following functional elements of the faceplate display:
Port views and status
Working with ports
Faceplate data windows
2 – Using SANsurfer Switch Manager
Using the Faceplate Display
Figure 2-11. Faceplate Display
59056-02 A 2-29
2 – Using SANsurfer Switch Manager Using the Faceplate Display
2.12.1

Port Views and Status

Port color and text provide information about the port and its operational state. Green indicates active; gray indicates inactive. The faceplate display provides the following views of port status corresponding to the View menu options in the faceplate display. Refer to ”Monitoring Port Status” on page 5-2 for more information about these displays.
Port type
Port state
Port speed
Port media
Context-sensitive popup menus are displayed when you right-click the faceplate image or a port icon in the faceplate display.
2.12.2

Working with Ports

Ports are selectable and serve as access points for other displays and menus. You select ports to display information about them in the data window or to modify them. Context-sensitive popup menus are displayed when you right-click the faceplate image or on a port icon in the faceplate display.
0
2.12.2.1
Selecting Ports
You can select ports in the following ways. Selected ports are outlined in white.
To select a port, click the port in the faceplate display.
To select a range of consecutive ports, select a port, then press and hold the
To select several non-consecutive ports, hold the Control key while
To select all ports, right-click on the faceplate image. Select Select All Ports
To cancel a selection, press and hold the Control key and select it again.
shift key and select another port. The application selects both end ports and all ports in between in port number sequence.
selecting.
from the popup menu.
2-30 59056-02 A
0
2.12.2.2
Opening the Faceplate Popup Menu
To open the popup menu, right-click on the faceplate image to present the following tasks.
Refresh the switch
Select all ports
Manage switch properties
Manage network properties
Manage SNMP properties
Extended credits wizard
Manage port properties
Change the port symbolic name
Run the port loopback tests
If no ports are selected, the port-related tasks will be unavailable in the menu. Right-click a port to open the Port popup menu. Hold down the Shift or Control key to select more than one port. If multiple ports are selected, right-click one of the selected ports.
2 – Using SANsurfer Switch Manager
Using the Faceplate Display
2.12.3

Faceplate Data Windows

The faceplate display provides the following data windows corresponding to the data window tabs:
Devices – displays information about devices (hosts and storage targets)
connected to the switch.
Switch – displays current switch configuration data.
Port Statistics – displays performance data for the selected ports.
Port Information – displays information for the selected ports.
Configured Zonesets – displays all zone sets, zones, and zone membership
in the zoning database.
59056-02 A 2-31
2 – Using SANsurfer Switch Manager Using the Faceplate Display
Notes
0
2-32 59056-02 A
This section describes the following tasks that manage fabrics:
Fabric Security
Fabric Tracker
Managing the Fabric Database
Working with Device Information and Nicknames
Displaying Fabric Information
Zoning a Fabric
3.1

Fabric Security

The components of Fibre Channel fabric security are:
User account security
Fabric services
3.1.1

User Account Security

User account security is the process by which your user account and password are authenticated with the list of valid user accounts and passwords. The switch validates your account and password when you attempt to add a fabric using SANsurfer Switch Manager or log in to a switch through Telnet. Your system administrator defines accounts, passwords, and authority levels that are stored on the switch. Refer to ”Managing User Accounts” on page 4-2 for more information.
Section 3
Managing Fabrics
The Admin account possesses Admin authority which grants full access to all tasks of the SANsurfer Switch Manager menu system. The switch validates your user account and SANsurfer Switch Manager grants access to its menus according to your authority level. If you do not have Admin authority, you are limited to monitoring tasks.
Note: If a user is logged into a switch using SANsurfer Switch Manager or
CLI, and an administrator changes user access rights or passwords, existing logins will not be affected by the new settings. Login access and privileges are only checked for a new login request.
59056-02 A 3-1
3 – Managing Fabrics Fabric Security
3.1.2

Fabric Services

Fabric services security includes SNMP and In-band management. Simple Network Management Protocol (SNMP) is the protocol governing network management and monitoring of network devices. SNMP security consists of a read community string and a write community string, that are basically the passwords that control read and write access to the switch. The read community string ("public") and write community string ("private") are set at the factory to these well-known defaults and should be changed if SNMP is enabled using the SNMP Properties dialog. If SNMP is enabled (default) and the read and write community strings have not been changed from their defaults, you risk unwanted access to the switch. Refer to ”Enabling SNMP Configuration” on page 3-2 for more information. SNMP is enabled by default.
In-band management is the ability to manage switches across inter-switch links using SANsurfer Switch Manager, SNMP, management server, or the application programming interface. The switch comes from the factory with in-band management enabled. If you disable in-band management on a particular switch, you can no longer communicate with that switch by means other than a direct Ethernet or serial connection. Refer to ”Enabling In-band Management” on
page 3-2 for more information.
0
3.1.2.1
Enabling SNMP Configuration
To enable SNMP configuration, do the following:
1. On the faceplate display, open the Switch menu and select SNMP Properties to open the SNMP Properties dialog.
2. In the SNMP Configuration area, place a check mark in the SNMP Enabled check box.
3. Click the OK button to save the change to the database.
3.1.2.2
Enabling In-band Management
To enable In-band Management, do the following:
1. On the faceplate display, open the Switch menu and select Switch Properties to open the Switch Properties dialog.
2. Click the In-band Management Enable button.
3. Click the OK button to save the change to the database.
3-2 59056-02 A
0
3.2

Fabric Tracker

The Fabric Tracker option enables you to generate a snapshot or baseline of current system version information, which can be viewed, analyzed and compared to other snapshot files, and exported to a file. Information includes date and time, SANsurfer Switch Manager version, switch active firmware version, device hardware, drivers, and firmware version from FDMI.
The Snapshot Analyzer option enables you to:
Compare two snapshots
Detect mismatches of firmware and driver versions
Detect devices that have been moved, added to or removed from the fabric.
3.2.1

Saving a Version Snapshot

To save the current snapshot to an XML file, open the Fabric menu, select Fabric Tracker, and select Save Snapshot. To view and analyze system version information, open the Fabric menu, select Fabric Tracker, and select Analyze Snapshots. The Fabric Version Snapshot Analysis dialog, shown in Figure 3-1,
opens with the Summary, Differences and Reports tab pages. Click the Browse buttons to open and view the snapshot files in the corresponding tab pages. Click the Close button to exit the Fabric Version Snapshot Analysis dialog. The color key below the scrollable area defines the meanings of the colors used.
3 – Managing Fabrics
Fabric Tracker
The Summary tab page shows a brief description of the changes that have occurred between the older snapshot and the newer one. Use the Summary tab page quickly view what has changed.
3.2.2

Viewing and Comparing Version Snapshots

The Differences tab page shows a side-by-side comparison of two snapshots. The timestamp of each snapshot is displayed above the scroll area showing that snapshot. The background color of the older snapshot is darker than the background of the newer snapshot. The arrow icon between the snapshot selectors always points from the older snapshot to the newer one. If the two snapshots have the same timestamp, the arrow will not be displayed. The scroll bars are synchronized to view the same portion of each snapshot file simultaneously. Click and drag the separator bar between the two panes to resize each pane. At the top of the separator bar between the two panes, click the left/right arrows to close the corresponding pane. The left/right arrows move to one side.
59056-02 A 3-3
3 – Managing Fabrics Managing the Fabric Database
3.2.3

Exporting Version Snapshots to a File

The Reports tab page enables you to select one of several reports to save to a text file. The are two types of reports. The Summary report type shows the same format displayed on the Summary tab page without the color highlighting. The Detail report type shows a detailed breakdown of the differences. Use the Export button to save the selected report to a text file.
0
Figure 3-1. Fabric Version Snapshot Analysis Dialog
3.3

Managing the Fabric Database

A fabric database contains the set of fabrics that you have added during a SANsurfer Switch Manager session. Initially, if you do not open an existing fabric or fabric view file, the SANsurfer Switch Manager application opens with an empty fabric database.
3-4 59056-02 A
0
3.3.1

Adding a Fabric

To add a fabric to the database, do the following:
1. Open the Fabric menu and select Add Fabric to open the Add a New Fabric
3 – Managing Fabrics
Managing the Fabric Database
dialog as shown in Figure 3-2.
Figure 3-2. Add a New Fabric Dialog
2. Enter a fabric name (optional) and the IP address of the switch through which to manage the fabric.
3. Enter an account name and password. The factory account name and password are "admin" and "password". The password is for the switch and is stored in the switch firmware. Refer to ”Managing User Accounts” on
page 4-2 or the ”User Command” on page A-94 for information about
creating user accounts.
4. Click the Add Fabric button.
Note: A switch supports a combined maximum of 19 logins or sessions
reserved as follows:
4 logins or sessions for internal applications such as
management server and SNMP
9 high priority Telnet sessions
6 logins or sessions for SANsurfer Switch Manager inband
and out-of-band logins, Application Programming Interface (API) inband and out-of-band logins, and Telnet logins. Additional logins will be refused.
59056-02 A 3-5
3 – Managing Fabrics Managing the Fabric Database
3.3.2

Removing a Fabric

To delete a fabric file from the database, do the following:
1. Select a fabric in the fabric tree.
2. Open the Fabric menu and select Remove Fabric.
3.3.3

Opening a Fabric View File

A fabric view file is one or more fabrics saved to a file. To open an existing view file, do the following:
1. Open the File menu and select Open View File, or click the Open button. If the fabric you are currently viewing has changed, you will be prompted to save the changes to the fabric view file with the Save View dialog before opening a different view file.
2. In the Open View dialog, enter the name of the file to open, and enter a file password, if a password was entered when this fabric view file was saved.
0
3. Click the OK button.
3.3.4

Saving a Fabric View File

To save a fabric view file, do the following:
1. Open the File menu, and select Save View As.
2. In the Save View dialog, enter a new file name.
3. Enter a file password, if necessary.
4. Click the OK button.
3.3.5

Rediscovering a Fabric

After making changes to or deleting switches from a fabric view, it may be helpful to again view the actual fabric configuration. The rediscover fabric option clears out the current fabric information being displayed, and rediscovers all switch information. To rediscover a fabric, open the Fabric menu, and select Rediscover Fabric. The rediscover function is more comprehensive than the refresh function.
3-6 59056-02 A
0
3.3.6

Deleting Switches and Links

The SANsurfer Switch Manager application does not automatically delete switches or links that have failed or have been physically removed from the fabric. In these cases, you can delete switches and links to bring the display up to date. If you delete a switch or a link that is still active, the SANsurfer Switch Manager application will restore it automatically. You can also refresh the display. To delete a switch from the topology display, do the following:
1. Select one or more switches in the topology display.
2. Open the Switch menu and select Delete.
To delete a link, do the following:
1. Select one or more links in the topology display.
2. Open the Switch menu and select Delete.
3.3.7

Adding a New Switch to a Fabric

If there are no special conditions to be configured for the new switch, simply plug in the switch and the switch becomes functional with the default fabric configuration. The default fabric configuration settings are:
3 – Managing Fabrics
Managing the Fabric Database
Fabric zoning is sent to the switch from the fabric.
All 1-Gbps/2-Gbps ports will be GL_Ports; all 10-Gbps ports will be G_Ports.
The default IP address 10.0.0.1 is assigned to the switch without a gateway
or boot protocol configured (RARP, BOOTP, and DHCP).
If you are adding a new switch to a fabric and do not want to accept the default fabric configuration, do the following:
1. If the switch is not new from the factory, reset the switch to the factory configuration before adding the switch to the fabric by selecting Restore Factory Defaults in the Switch menu from the faceplate display.
2. If you want to manage the switch through the Ethernet port, you must first configure the IP address using the Network Properties dialog or the Configuration Wizard.
3. Configure any special switch settings. Consider configuring the Default Visibility setting to None in the Zoning Config dialog to prevent devices from finding other devices on all switches in the fabric until the new switch is configured. To open the Zoning Config dialog, open the Zoning menu, and select Edit Zoning Config.
4. Plug in the inter-switch links (ISL), but do not connect the devices.
59056-02 A 3-7
3 – Managing Fabrics Managing the Fabric Database
5. Configure the port types for the new switch using the Port Properties dialog. The 1-Gbps/2-Gbps ports can be G_Port, GL_Port, F_Port, FL_Port, or Donor. The 10-Gbps ports can be a G_Port or F_Port.
6. Connect the devices to the switch.
7. Make any necessary zoning changes using the Edit Zoning dialog. To open the Edit Zoning dialog, open the Zoning menu, and select Edit Zoning. If you changed the Default Visibility setting in the Zoning Config dialog from All to None, change that setting back to All. To open the Zoning Config dialog, open the Zoning menu, and select Edit Zoning Config.
3.3.8

Replacing a Failed Switch

The archive/restore works for all switches. However, the Restore menu item is not available for the in-band switches. You can only restore a switch out-of-band (the fabric management switch). There are certain parameters that are not archived, and these are not restored by SANsurfer Switch Manager. Refer to ”Archiving a
Switch” on page 4-29 and ”Restoring a Switch” on page 4-29 for information about
archive and restore. Use the following procedure to replace a failed switch for which an archive is available.
0
1. At the failed switch:
a. Turn off the power and disconnect the AC cords.
b. Note port locations and remove the interconnection cables and SFPs.
c. Remove the failed switch.
2. At the replacement switch:
a. Mount the switch in the location where the failed switch was removed.
b. Install the SFPs using the same ports as were used on the failed
switch.
CAUTION!
c. Attach the AC cords and power up the switch.
3. Select the failed switch in the topology display. Open the Switch menu and select Delete.
Do not reconnect inter-switch links, target devices, and initiator devices at this time. Doing so could invalidate the fabric zoning configuration.
3-8 59056-02 A
0
4. Restore the configuration from the failed switch to the replacement switch:
a. Open a new fabric through the replacement switch.
b. Open the faceplate display for the replacement switch. Open the
Switch menu and select Restore.
c. In the Restore dialog, enter the archive file from the failed switch or
browse for the file.
d. Click the Restore button.
5. Reset the replacement switch to activate the configuration formerly possessed by the failed switch including the domain ID and the zoning database. Open the Switch menu and select Reset Switch.
6. Reconnect the inter-switch links, target devices, and initiator devices to the replacement switch using the same ports as were used on the failed switch.
3.4

Displaying Fabric Information

The topology display is your primary tool for monitoring a fabric. The graphic window of the topology display provides status information for switches, inter-switch links, and the Ethernet connection to the management workstation.
3 – Managing Fabrics
Displaying Fabric Information
The data window tabs show device, switch, and active zone set information. The Active Zoneset tab shows the zone definitions for the active zone set. Refer to
”Devices Data Window” on page 3-15 and ”Switch Data Window” on page 4-8 for
information about the Devices and Switch data windows.
59056-02 A 3-9
3 – Managing Fabrics Displaying Fabric Information
3.4.1

Fabric Status

The fabric updates the topology and faceplate displays by forwarding changes in status to the management workstation as they occur. You can allow the fabric to update the display status, or you can refresh the display at any time. To refresh the topology display, do one of the following:
Click the Refresh button.
Open the View menu and select Refresh.
Press the F5 key.
Right-click anywhere in the background of the topology display and select
Refresh Fabric from the popup menu.
The topology display uses switch and status icons to provide status information about switches, inter-switch links, and the Ethernet connection. The switch status icons, displayed on the left side of a switch, vary in shape and color. Switches controlled by an Ethernet Internet Protocol have a colored Ethernet icon displayed on the right side of the switch. A green Ethernet icon indicates normal operation, yellow indicates a condition that may require attention to maintain maximum performance, and red indicates a potential failure. Tab le 3- 1 shows the different switch icons and their meanings.
0
Table 3-1. Topology Display Switch and Status Icons
Switch Icon Description
SANbox 5200 Series Switch
Normal operation (Green)Warning–operational with errors (Yellow)Critical–potential failure (Red)Unknown–communication status unknown,
unreachable, or unmanageable (Blue)
Fabric Management Switch
Ethernet connection normal (Green)Ethernet connection warning (Yellow)Ethernet connection critical (Red)
Switch is not manageable with this version of SANsurfer Switch Manager. Use the management application that was shipped with this switch.
3-10 59056-02 A
0
3.4.2

Displaying the Event Browser

The Event Browser displays a list of events generated by the switches in the fabric and the SANsurfer Switch Manager application. Events that are generated by the SANsurfer Switch Manager application are not saved on the switch, but can be saved to a file during the SANsurfer Switch Manager session.
Entries in the Event Browser shown in Figure 3-3, are formatted by severity, time stamp, source, type, and description. The maximum number of entries allowed in the Event Browser is 10,000. The maximum number of entries allowed on a switch is 1200. Once the maximum is reached, the event list wraps and the oldest events are discarded and replaced with the new events. Event entries from the switch, use the switch time stamp, while event entries generated by the application have a workstation time stamp. You can filter, sort, and export the contents of the Event Browser to a file. The Event Browser begins recording when enabled and SANsurfer Switch Manager is running.
If the Event Browser is enabled using the Preferences dialog, the next time SANsurfer Switch Manager is started all events from the switch log will be displayed. If the Event Browser is disabled when SANsurfer Switch Manager is started and later enabled, only those events from the time the Event Browser was enabled and forward will be displayed.
3 – Managing Fabrics
Displaying Fabric Information
To display the Event Browser, open the Fabric menu and select Show Event Browser, or click the Events button on the tool bar. If the Show Event Browser selection or the Events button is grayed-out, you must first enable the Events Browser preference. Refer to ”Setting SANsurfer Switch Manager Preferences”
on page 2-14.
Column Sorting
Buttons
Severity
Column
Figure 3-3. Events Browser
59056-02 A 3-11
3 – Managing Fabrics Displaying Fabric Information
Severity is indicated in the severity column using icons as described in Table 3-2.
0
Table 3-2. Severity Levels
Severity
Icon
Alarm – An Alarm is any event that’s a "serviceable event". This means that attention by the user or field service is required. Alarms are events that get posted asynchronously to the screen. Alarms cannot be turned off. If the alarm denotes that a system error has occurred the customer and/or field representative will generally be directed to provide a "show support" capture of the switch.
Critical event – An event that indicates a potential failure. Critical log messages are events that warrant notice by the user. By default, these log messages will be posted to the screen. Critical log messages do not have alarm status as they require no immediate attention from a user or service representative.
Warning event – An event that indicates errors or other conditions that may require attention to maintain maximum performance. Warning messages will not be posted to the screen unless the log is configured to do so. Warning messages are not disruptive and, therefore, do not meet the criteria of Critical. The user need not be informed asynchronously
No icon Informative – An unclassified event that provides supporting
information.
Description
Note:  Events (Alarms, Critical, Warning, and Informative) generated by
the application are not saved on the switch. They are permanently discarded when you close a SANsurfer Switch Manager session, but you can save these events to a file on the workstation before you close SANsurfer Switch Manager and read it later with a text editor or browser.
Events generated by the switch, are stored on switch, and will be
retrieved when the application is restarted. Some alarms are configurable. Refer to ”Configuring Port Threshold Alarms” on
page 4-13.
3-12 59056-02 A
0
3.4.2.1
Filtering the Event Browser
Filtering the Event Browser enables you to display only those events that are of interest based on the event severity, timestamp, source, type, and description. To filter the Event Browser, open the Filter menu and select Filter Entries. This opens the Filter Events dialog shown in Figure 3-4. The Event Browser displays those events that meet all of the criteria in the Filter Events dialog. If the filtering criteria is cleared or changed, then all the events that were previously hidden that satisfy the new criteria will be shown.
You can filter the event browser in the following ways:
Severity – Check one or more of the corresponding check boxes to display
alarm events, critical events, warning events, or informative events.
Date/Time – Check one or both of the From: and To: check boxes. Enter the
bounding timestamps (MM/dd/yy hh:mm:ss aa) to display only those events that fall within those times. ("aa" indicates AM or PM.) The current year (yy) can be entered as either 2 or 4 digits. For example, 12/12/03 will be interpreted December 12, 2003.
3 – Managing Fabrics
Displaying Fabric Information
Text – Check one or more of the corresponding check boxes and enter a text
string (case sensitive) for event source, type, and description. The Event Browser displays only those events that satisfy all of the search specifications for the Source, Type, and Description text.
Figure 3-4. Filter Events Dialog
59056-02 A 3-13
3 – Managing Fabrics Displaying Fabric Information
3.4.2.2
Sorting the Event Browser
Sorting the Event Browser enables you to display the events in alphanumeric order based on the event severity, timestamp, source, type, or description. Initially, the Event Browser is sorted in ascending order by timestamp. To sort the Event Browser, click the Severity, Timestamp, Source, Type, or Description column buttons. You can also open the Sort menu and select By Severity, By Timestamp, By Source, By Type, or By Description. Successive sort operations of the same type alternate between ascending and descending order.
3.4.2.3
Saving the Event Browser to a File
You can save the displayed Event Browser entries to a file. Filtering affects the save operation, because only displayed events are saved. To save the Event Browser to a file, do the following:
1. Filter and sort the Event Browser to obtain the desired display.
0
2. Open the File menu and select Save As.
3. Select a folder and enter a file name in which to save the event log and click the Save button. The file can be saved in XML, CSV, or text format. XML files can be opened with an internet browser or text editor. CSV files can be opened with Microsoft Excel or most spreadsheet applications.
3-14 59056-02 A
0
3.4.3

Devices Data Window

The Devices data window displays information about devices (hosts and storage targets) connected to the switch. Click the Devices tab below the data window to display device information for all devices that are logged into the selected fabric. To narrow the display to devices that are logged into specific switches, select one or more switches in the fabric tree or the topology display. Table 3-3 describes the entries in the Devices data window. Refer to ”Exporting Device Information to a
File” on page 3-18 for exporting device information.
Entry Description
Port WWN Port world wide name
Nickname Device port nickname. To create a new nickname or edit an
3 – Managing Fabrics
Displaying Fabric Information
Table 3-3. Devices Data Window Entries
existing nickname, double-click the cell and enter a nickname in the Edit Nickname dialog. Refer to ”Managing Device Port
Nicknames” on page 3-18 for more information.
Details Click the (i) to display additional detail about the device. Refer
to ”Displaying Detailed Device Information” on page 3-17.
FC Address Fibre Channel address
Switch Switch name
Port Switch port number
Target/Initiator Device type: target or initiator
Vendor Host Bus Adapter/Device Vendor
Host Name Name of host
Active Zones The active zone to which the device belongs
Row # Number of port as displayed in the faceplate display
59056-02 A 3-15
3 – Managing Fabrics Displaying Fabric Information
3.4.4

Active Zone Set Data Window

The Active Zoneset data window displays the zone membership for the active zone set that resides on the fabric management switch. The active zone set is the same on all switches in the fabric – you can confirm this by adding a fabric through another switch and comparing Active Zone Set displays.
To open the Active Zoneset data window, click the Active Zoneset tab below the data window in the topology display. Refer to ”Configured Zonesets Data
Windows” on page 4-12 for information about the zone set definitions on a
particular switch. Refer to ”Zoning a Fabric” on page 3-20 for more information about zone sets and zones.
The Active Zoneset data window, shown in Figure 3-5, uses display conventions for expanding and contracting entries that are similar to the fabric tree. An entry handle located to the left of an entry in the tree indicates that the entry can be expanded. Click this handle or double-click the following entries:
A zone set entry expands to show its member zones.
0
A zone entry expands to show its member ports/devices.
Ports/devices that are zoned by WWN or FC address, but no longer part of
the fabric, are grayed-out.
Active Zoneset
Data Window
Figure 3-5. Active Zone Set Data Window
3-16 59056-02 A
0
3.4.5

Working with Device Information and Nicknames

Link Data Window

The Link data window displays information about all switch links in the fabric or selected links. This information includes the switch name, the port number at the end of each link, and the link status icons. To open the Link data window, click the Link tab below the data window in the topology display.
3.5
Working with Device Information and Nicknames
SANsurfer Switch Manager enables you to do the following:
Display detailed device information
Export device information to a file
Manage device port nicknames
3.5.1

Displaying Detailed Device Information

In addition to the information that is available in the Devices data window, you can click the (i) in the Details column to display more information as shown in
Figure 3-6.
3 – Managing Fabrics
Figure 3-6. Detailed Devices Display Dialog
59056-02 A 3-17
3 – Managing Fabrics Working with Device Information and Nicknames
3.5.2

Exporting Device Information to a File

To save device information to a file, open the topology display and do the following:
1. Select one or more switches. If no switches are selected, Devices information is gathered for all switches.
2. Open the Switch menu and select Export Devices Information.
3. In the Save dialog, enter a file name.
4. Click the Save button.
3.5.3

Managing Device Port Nicknames

You can assign a nickname to a device port World Wide Name. A nickname is a user-definable, meaningful name that can be used in place of the World Wide Name. Assigning a nickname makes it easier to recognize device ports when zoning your fabric or when viewing the Devices data window.
0
SANsurfer Switch Manager maintains nicknames in Nicknames.xml, which is found in your working directory. In addition to creating, editing, and deleting nicknames, you can also export the nicknames to a file, which can then be imported into the Nicknames.xml file on other workstations.
3.5.3.1
Creating a Nickname
To create a device port nickname, do the following:
1. Open the File menu and select Nicknames to open the Nicknames dialog.
2. Choose one of the following methods to enter a nickname. A nickname must start with a letter and can have up to 64 characters. Valid characters include alphanumeric characters [aA-zZ][0-9] and special symbols [$ _ - ^ ].
Click on a device in the table. Open the Edit menu and select Create
Nickname to open the Add Nickname dialog. In the Add Nickname dialog, enter a nickname and WWN and click the OK button.
Double-click a cell in the Nicknames column, and enter a new
nickname in the text field. Click the Save button to save the changes and exit the Nicknames dialog.
You can also create a nickname by double clicking a cell in the Nickname column of the Devices data window. Refer to ”Devices Data Window” on page 3-15.
3-18 59056-02 A
0
3.5.3.2
Editing a Nickname
A nickname must start with a letter and can have up to 64 characters. Valid characters include alphanumeric characters [aA-zZ][0-9] and special symbols [$ _
- ^ ]. You can access the Edit Nicknames dialog two ways. Choose one of the
following methods to edit a nickname:
In the topology or faceplate display, open the File menu and select
Nicknames to open the Nicknames dialog. The device entries are listed in table format.
3 – Managing Fabrics
Working with Device Information and Nicknames
Click on a device entry in the table. Open the Edit menu and
select Edit Nickname to open the Edit Nicknames dialog. Edit the nickname in the text field. Click the OK button to save the changes.
Double-click a cell in the Nicknames or WWN columns, and edit
the nickname in the text field. Click the OK button to save the changes.
In the topology or faceplate display, click the Devices tab to display the
Devices data window. Double-click a cell in the Nickname column to open the Edit Nickname dialog. Edit the nickname in the text field. Click the OK button to save the changes. Refer to ”Devices Data Window” on page 3-15 for more information.
3.5.3.3
Deleting a Nickname
To delete a device port nickname, do the following:
1. Open the File menu and select Nicknames to open the Nicknames dialog.
2. Click a device in the table. Open the Edit menu and select Delete Nickname.
3. Click the Save button to save the changes.
3.5.3.4
Exporting Nicknames to a File
You can save nicknames to a file. This is useful for distributing nicknames to other management workstations. To save nicknames to an XML file, do the following:
1. Open the File menu and select Nicknames to open the Nicknames dialog.
2. Open the File menu in the Nicknames dialog, and select Export.
3. Enter a name for the XML nickname file in the Save dialog and click Save.
59056-02 A 3-19
3 – Managing Fabrics Zoning a Fabric
3.5.3.5
Importing a Nicknames File
Importing a nicknames file copies its contents into and replaces the contents of the Nicknames.xml file which is used by SANsurfer Switch Manager. To import a nickname file, do the following:
1. Open the File menu and select Nicknames to open the Nicknames dialog.
2. Open the File menu in the Nicknames dialog, and select Import.
3. Select an XML nickname file in the Open dialog and click Open. When prompted to overwrite existing nicknames, click Yes.
3.6

Zoning a Fabric

Zoning enables you to divide the ports and devices of the fabric into zones for more efficient and secure communication among functionally grouped nodes. This subsection addresses the following topics:
Zoning concepts
0
Using the Zoning Wizard
Managing the zoning database
Managing zone sets
Managing zones
Managing aliases
Merging fabrics and zoning
3.6.1

Zoning Concepts

The following zoning concepts provide some context for the zoning tasks described in this section:
Zones
Aliases
Zone sets
Zoning database
Zoning configuration
3-20 59056-02 A
0
3.6.1.1
Zones
3 – Managing Fabrics
Zoning a Fabric
A zone is a named group of ports or devices that can communicate with each other. Devices within a zone can only communicate with other devices in the same zone. A device may participate in more than one zone.
Membership in a zone can be defined by switch domain ID and port number, device Fibre Channel address (FCID), or device World Wide Name (WWN).
WWN entries define zone membership by the World Wide Name of the
attached device. With this membership method, you can move WWN member devices to different switch ports in different zones without having to edit the member entry as you would with a domain ID/port number member. Furthermore, unlike FCID members, WWN zone members are not affected by changes in the fabric that could change the Fibre Channel address of an attached device.
FCID entries define zone membership by the Fibre Channel address of the
attached device. With this membership method you can replace a device on the same port without having to edit the member entry as you would with a WWN member.
3.6.1.1.1
Soft Zones
Domain ID/Port number entries define zone membership by switch domain
ID and port number. All devices attached to the specified port become members of the zone. The specified port must be an F_Port or an FL_Port.
Two types of zones are supported:
Soft zone
Hard zone - Access Control List (domain/port member only or it will revert
back to a soft zone when activated)
Soft zoning divides the fabric for purposes of controlling discovery. Devices within the same soft zone automatically discover and communicate freely with all other members of the same zone. The soft zone boundary is not secure; traffic across soft zones can occur if addressed correctly. Soft zones that include members from multiple switches need not include the ports of the inter-switch links. Soft zone boundaries yield to ACL zone boundaries. Soft zones can overlap; that is, a device can participate in more than one soft zone. Zone membership can be defined by Fibre Channel address, domain ID and port number, World Wide Name, or a combination. Soft zoning supports all port types.
59056-02 A 3-21
3 – Managing Fabrics Zoning a Fabric
3.6.1.1.2
Access Control List Hard Zones
Access Control List (ACL) zoning divides the fabric for purposes of controlling discovery and inbound traffic. ACL zoning is a type of hard zoning that is hardware enforced. This type of zoning is useful for controlling access to certain devices without totally isolating them from the fabric. Devices can communicate with each other and transmit outside the ACL zone, but cannot receive inbound traffic from outside the zone. The ACL zone boundary is secure against inbound traffic. ACL zones can overlap; that is, a port can be a member of more than one ACL zone. ACL zones that include members from multiple switches need not include the ports of the inter-switch links. ACL zone boundaries supersede soft zone boundaries. Membership can be defined only by domain ID and port number. ACL zoning supports all port types.
3.6.1.2
Aliases
To make it easier to add a group of ports or devices to one or more zones, you can create an alias. An alias is a named set of ports or devices that are grouped together for convenience. Unlike zones, aliases impose no communication restrictions between its members. You can add an alias to one or more zones. However, you cannot add a zone to an alias, nor can an alias be a member of another alias.
0
3.6.1.3
Zone Sets
A zone set is a named group of zones. A zone can be a member of more than one zone set. Each switch in the fabric maintains its own zoning database containing one or more zone sets. This zoning database resides in non-volatile or permanent memory and is therefore retained after a reset. Refer to ”Configured Zonesets
Data Windows” on page 4-12 for information about displaying the zoning
database.
The orphan zone set is created by the application automatically to hold the zones which are not in any set. The orphan zone set can’t be removed and is not saved on the switch.
To apply zoning to a fabric, choose a zone set and activate it. When you activate a zone set, the switch distributes that zone set and its zones, excluding aliases, to every switch in the fabric. This zone set is known as the active zone set. Refer to
”Active Zone Set Data Window” on page 3-16 for information about displaying the
active zone set.
3-22 59056-02 A
0
3.6.1.4
Zoning Database
Each switch has its own zoning database. The zoning database is made up of all aliases, zones, and zone sets that have been created on the switch or received from other switches. The switch maintains two copies of the inactive zoning database: one copy is maintained in temporary memory for editing purposes; the second copy is maintained in permanent memory. Zoning database edits are made on an individual switch basis and are not propagated to other switches in the fabric when saved.
There are two configuration parameters that affect the zoning database: Interop Auto Save and Default Visibility. The Interop Auto Save parameter determines whether changes to the active zone set that a switch receives from another switch in the fabric will be saved to permanent memory on that switch. The Default Visibility parameter permits or prohibits communication among ports/devices when there is no active zone set. Refer to ”Configuring the Zoning Database” on
page 3-28 for information about zoning configuration.
The following zoning limits are enforced during the configuration of zoning and during a zoning database merge from the fabric:
3 – Managing Fabrics
Zoning a Fabric
MaxZoneSets is 256. The maximum number of zone sets that can be
configured on the switch.
MaxZones is 1000. The maximum number of zones that can be configured
on the switch.
MaxAliases is 2500. The maximum number of aliases that can be
configured on the switch.
MaxTotalMembers is 10,000. The maximum number of total zone and alias
members that can be configured on the switch. Aliases are considered zone members since they can be added to a zone just like a normal zone member.
MaxZonesInZoneSets is 1000. The maximum number of zone linkages to
zonesets that can be configured on the switch. Every time a zone is added to a zoneset this constitutes a linkage.
MaxMembersPerZone is 2000. The maximum number of zone members
that can be added to any zone on the switch. Aliases are considered zone members when added to a zone.
MaxMembersPerAlias is 2000. The maximum number of zone members
that can be added to any alias on the switch.
59056-02 A 3-23
3 – Managing Fabrics Zoning a Fabric
3.6.2

Using the Zoning Wizard

The Zoning Wizard is a series of dialogs that leads you through the process of zoning a fabric. To open the Zoning Wizard, open the Wizards menu in the faceplate display, and select Zoning Wizard.
The Zoning Wizard helps you with the two most typical reasons for zoning:
Zoning Windows servers storage
Assign storage to servers.
To solve these problems, there must be at least one target and at least one initiator in the name server. Windows servers do not share devices well, but sometimes they must share devices, such as a tape drive. The wizard helps you define which devices are sharable and which ones are not. Once a device is in a Windows group, it can no longer be in any other group.
3.6.3

Managing the Zoning Database

0
Managing the zoning database consists of the following:
Editing the Zoning Database
Configuring the Zoning Database
Saving the Zoning Database to a File
Restoring the Zoning Database from a File
Restoring the Default Zoning Database
Removing All Zoning Definitions
3-24 59056-02 A
0
3.6.3.1
Editing the Zoning Database
To edit the zoning database for a particular switch, open the Zoning menu from the faceplate display and select Edit Zoning to open the Edit Zoning dialog shown in Figure 3-7. Changes can only be made to inactive zone sets, which are stored in flash (non-volatile) memory and retained after resetting a switch.
3 – Managing Fabrics
Zoning a Fabric
Port/Device
Tree
Zone Sets
Tree
Figure 3-7. Edit Zoning Dialog
To apply zoning to a fabric, choose a zone set and activate it. When you activate a zone set, the switch distributes that zone set and its zones, excluding aliases, to every switch in the fabric. This zone set is known as the active zone set.
You can not edit an active zone set on a switch. You must configure an inactive zone set to your needs and then activate that updated zone set to apply the changes to the fabric. When you activate a zone set, the switch distributes that zone set to the temporary zoning database on every switch in the fabric. However, in addition to the merged active zone set, each switch maintains its own original zone set in its zoning database. Only one zone set can be active at one time.
59056-02 A 3-25
3 – Managing Fabrics Zoning a Fabric
Note: If the Interop Auto Save parameter is enabled on the Zoning
The Edit Zoning dialog has a Zone Sets tree on the left and a Port/Device (or members) tree on the right. Both trees use display conventions similar to the fabric tree for expanding and contracting zone sets, zones, and ports. An expanded port shows the port Fibre Channel address; an expanded address shows the port World Wide Name. You can select zone sets, zones, and ports in the following ways:
Click a zone, zone set, or port icon.
Right-click to select a zone set or zone, and open the corresponding popup
0
Configuration dialog, then every time the active zone set changes, the switch will copy it into an inactive zone set stored on the switch. You can edit this copy of the active zone set stored on the switch, and activate the updated copy to conveniently apply the changes to the active zone set. The edited copy then becomes the active zone set.
menu.
Hold down the Shift key while clicking several consecutive icons.
Hold down the Control key while clicking several non-consecutive icons.
Using tool bar buttons, popup menus, or a drag-and-drop method, you can create and manage zone sets and zones in the zoning database. Ta bl e 3 -4 describes the zoning tool bar operations.
Use the Edit Zoning dialog to define zoning changes, and click the Apply button to open the Error Check dialog. Click the Error Check button to have SANsurfer Switch Manager check for zoning conflicts, such as empty zones, aliases, or zone sets, and ACL zones with non-domain ID/port number membership. Click the Save Zoning button to implement the changes. Click the Close button to close the Error Check dialog. On the Edit Zoning dialog, click the Close button to close the Edit Zoning dialog.
Table 3-4. Edit Zoning Dialog Tool Bar Buttons and Icons
Tool Bar Button Description
Create Zone Set button - create a new zone set
Create Zone button - create a new zone
3-26 59056-02 A
0
3 – Managing Fabrics
Zoning a Fabric
Table 3-4. Edit Zoning Dialog Tool Bar Buttons and Icons (Continued)
Tool Bar Button Description
Create Alias button - create another name for a set of objects
Add Member button - adds selected port/device to a zone
Remove Member button - delete the selected zone from a zone set, or delete the selected port/device from a zone
Switch port icon – not logged in
Switch port icon – logged in
NL_Port (loop) device icon – logged in to fabric
NL_Port (loop) device icon – not logged in to fabric
N_Port device icon – logged in to fabric
N_Port device icon – not logged in to fabric
59056-02 A 3-27
3 – Managing Fabrics Zoning a Fabric
3.6.3.2
Configuring the Zoning Database
Use the Zoning Config dialog to change the Auto Save and Default Visibility configuration parameters. In the faceplate display, open the Zoning menu and select Edit Zoning Config to open the Zoning Config dialog shown in Figure 3-8. After making changes, click the OK button to put the new values into effect.
Figure 3-8. Zoning Config Dialog
0
3.6.3.2.1
Interop Auto Save
The Interop Auto Save parameter determines whether changes to the active zone set that a switch receives from other switches in the fabric will be saved to the zoning database on that switch. Changes are saved when an updated zone set is activated. Zoning changes are always saved to temporary memory. However, if Interop Auto Save is enabled, the switch firmware saves changes to the active zone set in temporary memory and to the zoning database. If Interop Auto Save is disabled, changes to the active zone set are stored only in temporary memory which is cleared when the switch is reset.
Note: Disabling the Interop Auto Save parameter can be useful to prevent
the propagation of zoning information when experimenting with different zoning schemes. However, leaving the Interop Auto Save parameter disabled can disrupt device configurations should a switch have to be reset. For this reason, the Interop Auto Save parameter should be enabled in a production environment.
3-28 59056-02 A
0
3.6.3.2.2
Default Visibility
Default visibility determines the level of communication that is permitted among ports/devices when there is no active zone set. The default visibility parameter can be set differently on each switch. When default visibility is enabled (ALL) on a switch, all ports/devices on the switch can communicate with all ports/devices on switches that also have default visibility enabled. When Default Visibility is disabled (NONE), none of the ports/devices on that switch can communicate with any other port/device in the fabric.
3.6.3.3
Saving the Zoning Database to a File
You can save the zoning database to an XML file. You can later reload this zoning database on the same switch or another switch. To save a zoning database to a file, do the following:
1. In the faceplate display, open the Zoning menu, and select Edit Zoning.
2. In the Edit Zoning dialog, open the File menu and select Save As.
3 – Managing Fabrics
Zoning a Fabric
3. In the Save dialog, enter a file name for the database file.
4. Click the Save button to save the zoning file.
3.6.3.4
Restoring the Zoning Database from a File
CAUTION!
Do the following to restore the zoning database from a file to a switch:
1. In the faceplate display, open the Zoning menu and select Edit Zoning to open the Edit Zoning window.
2. Open the File menu and select Open File. A popup window will prompt you to select an XML zoning database file.
3. Select a file and click Open.
Restoring the zoning database from a file will replace the current zoning database on the switch.
59056-02 A 3-29
3 – Managing Fabrics Zoning a Fabric
3.6.3.5
Restoring the Default Zoning Database
Restoring the default zoning clears the switch of all zoning definitions.
0
CAUTION!
To restore the default zoning for a switch:
1. In the faceplate display, open the Zoning menu and select Restore Default Zoning.
2. Click the OK button to confirm that you want to restore default zoning and save changes to the zoning database.
3.6.3.6
This command will deactivate the active zone set.
Removing All Zoning Definitions
To clear all zone and zone set definitions from the zoning database, choose one of the following:
Open the Edit menu and select Clear Zoning. In the Removes All dialog,
click the Yes button to confirm that you want to delete all zones and zone sets.
Right-click the Zone Sets heading at the top of the Zone Sets tree, and
select Clear Zoning from the popup menu. Click the Yes button to confirm that you want to delete all zone sets and zones.
3-30 59056-02 A
0
3.6.4

Managing Zone Sets

Zoning a fabric involves creating a zone set, creating zones as zone set members, then adding devices as zone members. The zoning database supports multiple zone sets to serve the different security and access needs of your storage area network, but only one zone set can be active at one time. Managing zone sets consists of the following tasks:
Creating zone sets
Activating and deactivating zone sets
Copying a zone to a zone set
Removing a zone from one zone set or from all zone sets
Removing a zone set
Note: Changes that you make to the zoning database are limited to the
managed switch and do not propagate to the rest of the fabric. To distribute changes to configured zone sets fabric wide, you must edit the zoning databases on the individual switches.
3 – Managing Fabrics
Zoning a Fabric
3.6.4.1
Creating a Zone Set
To create a zone set, do the following:
1. Open the Zoning menu, and select Edit Zoning to open the Edit Zoning dialog.
2. Open the Edit menu, and select Create Zone Set to open the Create Zone Set dialog.
3. Enter a name for the zone set, and click the OK button. The new zone set name is displayed in the Zone Sets dialog. A zone set name must begin with a letter and be no longer than 64 characters. Valid characters are 0-9, A-Z, a-z, _, -, ^, and $.
4. To create new zones in a zone set, do one of the following:
Right-click a zone set and select Create A Zone from the popup menu.
Copy an existing zone by dragging a zone into the new zone set. Refer
5. Click the Apply button to save changes to the zoning database.
In the Create a Zone dialog, enter a name for the new zone, and click the OK button. The new zone name is displayed in the Zone Sets dialog.
to ”Copying a Zone to a Zone Set” on page 3-32.
59056-02 A 3-31
3 – Managing Fabrics Zoning a Fabric
3.6.4.2
Activating and Deactivating a Zone Set
You must activate a zone set to apply its zoning definitions to the fabric. Only one zone set can be active at one time. When you activate a zone set, the switch distributes that zone set to the temporary zoning database on every switch in the fabric.
The purpose of the deactivate function is to suspend all fabric zoning which results in free communication fabric wide or no communication depending on the default visibility setting. Refer to ”Default Visibility” on page 3-29 for more information. It is not necessary to deactivate the active zone set before activating a new one.
To activate a zone set, open the Zoning menu and select Activate Zone Set
to open the Activate Zone Set dialog. Select a zone set from the Select Zone Set pull-down menu, and click the Activate button.
To deactivate the active zone set, open the Zoning menu, select Deactivate
Zone Set. Acknowledge the warning about traffic disruption, and click the Yes button to confirm that you want to deactivate the active zone set.
0
3.6.4.3
Copying a Zone to a Zone Set
To copy an existing zone and its membership from one zone set to another, select the zone and drag it to the chosen zone set. Click the Apply button to save changes to the zoning database.
3.6.4.4
Removing a Zone from a Zone Set or from All Zone Sets
You can remove a zone from a zone set or from all zone sets in the database.
1. In the faceplate display, open the Zoning menu and select Edit Zoning to open the Edit Zoning dialog.
2. In the Zone Sets tree, select the zone(s) to be removed.
3. Open the Edit menu, and select Remove to remove the zone from the zone set, or select Remove from All Zones to remove the zone from all zone sets.
4. Click the Apply button to save changes to the zoning database.
Alternatively, you may use shortcut menus to remove a zone from a zone set or from all zone sets in the database.
3-32 59056-02 A
0
3.6.4.5
Removing a Zone Set
Removing a zone set from the database affects the member zones in the following ways.
Member zones that are members of other zone sets are not affected.
Member zones that are not members of other zone sets become members
of the orphan zone set. The orphan zone set can’t be removed and is not saved on the switch.
To delete a zone set from the database, do the following:
1. In the faceplate display, open the Zoning menu and select Edit Zoning to open the Edit Zoning dialog.
2. In the Zone Sets tree, select the zone set to be removed.
3. Open the Edit menu, and select Remove to remove the zone set.
4. Click the Apply button to save changes to the zoning database.
3 – Managing Fabrics
Zoning a Fabric
Alternatively, you may use shortcut menus to remove a zone set from the database.
3.6.5

Managing Zones

Managing zones involves the following:
Creating a Zone in a Zone Set
Adding Zone Members
Renaming a Zone or a Zone Set
Removing a Zone Member
Removing a Zone from a Zone Set
Removing a Zone from All Zone Sets
Changing Zone Types
Note: Changes that you make to the zoning database are limited to the
managed switch and do not propagate to the rest of the fabric. To distribute changes to configured zone sets fabric wide, you must edit the zoning databases on the individual switches.
59056-02 A 3-33
3 – Managing Fabrics Zoning a Fabric
3.6.5.1
Creating a Zone in a Zone Set
When a zone is created, its zone type is soft. To change the zone type to a hard zone, refer to ”Changing Zone Types” on page 3-37 for more information. Refer to
”Zones” on page 3-21 for information on zone types (soft and hard). To create a
zone in a zone set, do the following:
1. Open the Zoning menu, and select Edit Zoning to open the Edit Zoning dialog.
2. Select a zone set.
3. Open the Edit menu and select Create a Zone.
4. In the Create a Zone dialog, enter a name for the new zone, and click the OK button. The new zone name is displayed in the Zone Sets dialog. A zone name must begin with a letter and be no longer than 64 characters. Valid characters are 0-9, A-Z, a-z, _, ^, $, and -.
Note: If you enter the name of a zone that already exists in the
database, the SANsurfer Switch Manager application will ask if you would like to add that zone and its membership to the zone set.
0
5. To add switch ports or attached devices to the zone, do one of the following:
In the zone set tree, select the zone set. In the graphic window, select
the port to add to the zone. Open the Edit menu and select Add Members.
Select a port by port number, Fibre Channel address, or World Wide
Name in the Port/Device tree, and drag it into the zone.
Select a port by port number, Fibre Channel address, or World Wide
Name in the Port/Device tree. Right-click the zone and select Add Zone Members from the popup menu.
6. Click the Apply button to save changes to the zoning database.
3-34 59056-02 A
0
3.6.5.2
Adding Zone Members
You can zone a port/device by switch domain ID and port number, device port Fibre Channel address, or the device port WWN. Adding a port/device to a zone affects every zone set in which that zone is a member. To add ports/devices to a zone, do the following:
1. Open the Zoning menu, and select Edit Zoning to open the Edit Zoning dialog.
2. Choose one of the following methods to add the port/device:
Select a port/device in the Port/Device tree, and drag it into the zone.
To select multiple ports/devices, press and hold the Control key while selecting.
Select a port/device in the Port/Device tree. To select multiple
ports/devices, press the Control key while selecting. Select a zone set in the left pane. Open the Edit menu and select Add Members.
Select a port/device in the Port/Device tree. To select multiple
ports/devices, press the Control key while selecting. Select a zone set in the left pane. Click the Insert button.
3 – Managing Fabrics
Zoning a Fabric
If the port/device you want to add is not in the Port/Device tree, you can add it by doing the following:
a. Right click the selected zone.
b. Open the Edit menu and select Create Members.
c. Choose the WWN, Domain/Port, or First Port Address radio button.
d. Enter the hexadecimal value for the port/device according to the radio
button selection: 16 digits for a WWN member, 4 digits for a Domain/ Port member (DDPP), or a 6-digit Fibre Channel Address for a First Port Address member (DDPPAA) where D=domain ID, P=port number, and A=ALPA.
3. Click the OK button to add the member and save the change.
Note: Domain ID conflicts can result in automatic reassignment of switch
domain IDs. These reassignments are not reflected in zones that use domain ID/port number pair to define their membership. Be sure to reconfigure zones that are affected by a domain ID change.
59056-02 A 3-35
3 – Managing Fabrics Zoning a Fabric
3.6.5.3
Renaming a Zone or a Zone Set
To rename a zone, do the following:
1. In the Zone Sets tree of the Edit Zoning dialog, click the zone/zone set to be renamed.
2. Open the Edit menu and select Rename.
3. In the Rename Zone/Rename Zone Set dialog, enter a new name for the zone/zone set.
4. Click the OK button.
3.6.5.4
Removing a Zone Member
Removing a zone member will affect every zone and zone set in which that zone is a member. To remove a member from a zone:
1. In the Edit Zoning dialog, select the zone member to be removed.
0
2. Open the Edit menu and select Remove.
3. Click the OK button to save changes and close the Edit Zoning dialog.
3.6.5.5
Removing a Zone from a Zone Set
The orphan zone set is created by the application automatically to hold the zones which are not in any set. The orphan zone set can’t be removed and is not saved on the switch. To remove a zone from a zone set, do the following:
1. In the Edit Zoning dialog, select the zone to be removed. The selected zone will be removed from that zone set only.
2. Open the Edit menu and select Remove.
3. Click the OK button to save changes and close the Edit Zoning dialog.
3.6.5.6
Removing a Zone from All Zone Sets
To remove a zone from all zone sets, do the following:
1. In the Edit Zoning dialog, select the zone to be removed.
2. Open the Edit menu and select Remove Zone from All Sets.
3. Click the OK button to save changes and close the Edit Zoning dialog.
3-36 59056-02 A
0
3.6.5.7
Changing Zone Types
To change a zone type, do the following:
1. In the faceplate display, select the switch with the zone type to change.
2. Click the Zoning button to open the Edit Zoning dialog.
3. In the Zone Sets tree, select the zone to change.
4. Open the Edit menu and select Set Zone Type to open the Set Zone Type dialog.
5. Open the Zone Type pull-down menu and select Soft or ACL.
Soft zoning is the least restrictive type of zoning.
ACL zoning is hard zoning and is enforced by hardware and defines
access to a given port. ACL zones need not include inter-switch links.
3.6.6

Managing Aliases

An alias is a collection of objects that can be zoned together. An alias is not a zone, and can not have a zone or another alias as a member.
3 – Managing Fabrics
Zoning a Fabric
Note: Changes that you make to the zoning database are limited to the
3.6.6.1
Creating an Alias
To create an alias, do the following:
1. Open the Zoning menu, and select Edit Zoning to open the Edit Zoning dialog.
2. Open the Edit menu, and select Create Alias to open the Create Alias dialog.
3. Enter a name for the alias, and click the OK button. The alias name is displayed in the Zone Sets dialog. An alias name must begin with a letter and be no longer than 64 characters. Valid characters are 0-9, A-Z, a-z, _, $, ^, and -.
4. Click the OK button to save the alias name to the zoning database.
managed switch and do not propagate to the rest of the fabric. To distribute changes to configured zone sets fabric wide, you must edit the zoning databases on the individual switches.
You will not see aliases in the active zone set.
59056-02 A 3-37
3 – Managing Fabrics Zoning a Fabric
3.6.6.2
Adding a Member to an Alias
You can add a port/device to an alias by domain ID and port number, device port Fibre Channel address, or the device port WWN. To add ports/devices to an alias, do the following:
1. Open the Zoning menu, and select Edit Zoning to open the Edit Zoning dialog.
2. Choose one of the following methods to add the port/device:
Select a port/device in the Port/Device tree, and drag it into the alias.
To select multiple ports/devices, press and hold the Control key while selecting.
Select a port/device in the Port/Device tree. Click an alias to select
multiple ports/devices, press the Control key while selecting. Select an alias. Open the Edit menu and select Add Members.
Select a port/device in the Port/Device tree. To select multiple
ports/devices, press the Control key while selecting. Select an alias. Click the Insert button.
0
If the port/device you want to add is not in the Port/Device tree, you can add it by doing the following:
a. Right click the selected alias.
b. Open the Edit menu and select Create Members.
c. Choose the WWN, Domain/Port, or First Port Address radio button.
d. Enter the hexadecimal value for the port/device according to the radio
button selection: 16 digits for a WWN member, 4 digits for a Domain/ Port member (DDPP), or a 6-digit Fibre Channel Address for a First Port Address member (DDPPAA) where D=domain ID, P=port number, and A=ALPA.
3. Click the OK button to add the member and save the change.
3.6.6.3
Removing an Alias from All Zones
To remove an alias from all zones, do the following:
1. In the Zone Sets tree in the Edit Zoning dialog, select the alias to be removed.
2. Open the Edit menu, and select Remove Alias from All Zones.
3. Click the Yes button in the Remove dialog.
3-38 59056-02 A
0
3.6.7

Merging Fabrics and Zoning

If you join two fabrics with an inter-switch link, the active zone sets from the two fabrics attempt to merge automatically. The fabrics may consist of a single switch or many switches already connected together. The switches in the two fabrics attempt to create a new active zone set containing the union of each fabric's active zone set. The propagation of zoning information only affects the active zone set, not the configured zone sets, unless Interop Auto Save is turned on.
3.6.7.1
Zone Merge Failure
If a zone merge is unsuccessful, the inter-switch links between the fabrics will isolate due to a zone merge failure, which will generate an alarm. The reason for the E_Port isolation can also be determined by viewing the port information. Refer to ”Port Information Data Window” on page 5-8 and the ”Show Command” on
page A-61 (Port keyword).
A zone merge will fail if the two active zone sets have member zones with identical names that differ in membership or type. For example, consider Fabric A and Fabric B each with a soft zone named “ZN1” in its active zone set. Fabric A "ZN1" contains a member specified by Domain ID 1 and Port 1; Fabric B “ZN1” contains a member specified by Domain ID 1 and Port 2. In this case, the merge will fail because the two zones have the same name, but different membership.
3 – Managing Fabrics
Zoning a Fabric
59056-02 A 3-39
3 – Managing Fabrics Zoning a Fabric
3.6.7.2
Zone Merge Failure Recovery
When a zone merge failure occurs, the conflict that caused the failure must be resolved. You can correct a failure due to a zone conflict by deactivating one of the active zone sets or by editing the conflicting zones so that their membership is the same. You can deactivate the active zone set on one fabric if the active zone set on the other fabric accurately defines your zoning needs. If not, you must edit the zone memberships, and reactivate the zone sets. After correcting the zone membership, reset the isolated ports to allow the fabrics to join.
Note: If you deactivate the active zone set in one fabric and the Interop Auto
Save parameter is enabled, the active zone set from the second fabric will propagate to the first fabric and replace all zones with matching names in the configured zone sets.
If the zone sets to merge have the same Zone A that only differ in the type of zone (soft vs. ACL), the zone sets will merge. If this is a 2 switch fabric, Switch 1 will state that Zone A is soft and Switch 2 will state that Zone A is ACL.
0
Refer to ”Managing Zones” on page 3-33 for information about adding and removing zone members. Refer to ”Resetting a Port” on page 5-15 for information about resetting a port.
3-40 59056-02 A
Section 4
Managing Switches
This section describes the following tasks that manage switches in the fabric.
Managing User Accounts
Displaying Switch Information
Configuring Port Threshold Alarms
Paging a Switch
Setting the Date/Time and Enabling NTP Client
Resetting a Switch
Configuring a Switch
Archiving a Switch
Restoring a Switch
Restoring the Factory Default Configuration
Installing Firmware
Downloading a Support File
Upgrading the Switch Using License Keys
Displaying Hardware Status
59056-02 A 4-1
4 – Managing Switches Managing User Accounts
4.1

Managing User Accounts

Only the Admin account can manage user accounts with the User Account Administration dialogs. However, any user can modify their own password. To open the User Account Administration dialogs, open the Switch menu in the
faceplate display, and select User Accounts.... A user account consists of the
following:
Account name or login
Password
Authority level
Expiration date
Switches come from the factory with the following user accounts:
Account Name Password Admin Authority Expiration
0
Table 4-1. Factory User Accounts
admin admin true never expires
images images false never expires
The Admin account is the only user that can manage all user accounts with the User Account Administration dialogs. The Admin account can create, remove, or modify user accounts, and change account passwords. The Admin account can also view and modify the switch and its configuration with SANsurfer Switch Manager. The Admin account can not be removed.
Users with Admin authority can view and modify the switch and its configuration using SANsurfer Switch Manager. Users without Admin authority are limited to viewing switch status and configuration.
The Images account can not be removed, and is required for exchanging files with the switch using FTP.
4-2 59056-02 A
0
4.1.1

Creating User Accounts

To create a user account on a switch, open the Switch menu in the faceplate
display and select User Accounts.... This displays the User Account
Administration dialog shown in Figure 4-1. A switch can have a maximum of 15 user accounts.
4 – Managing Switches
Managing User Accounts
Figure 4-1. User Account Administration Dialog – Add Account
1. To open the User Account Administration dialogs, open the Switch menu in
the faceplate display, and select User Accounts....
2. Click the Add Account tab to open the Add Account tab page.
3. Enter an account name in the New Account Login field. Account names are limited to 15 characters.
4. If the account is to have the ability to modify switch configurations, check the Admin Authority Enabled box.
5. Enter a password in the New Password field and enter it again in the Verify Password field. A password must have a minimum of 4 characters and no more than 20.
6. If this account is to be permanent with no expiration date, click the
Permanent Account radio button. Otherwise, click the Account Will Expire button and enter the number days in which the account will expire.
7. Click the Add Account button to add the newly defined account.
59056-02 A 4-3
4 – Managing Switches Managing User Accounts
4.1.2

Removing a User Account

To remove a user account on a switch, open the Switch menu in the faceplate
display and select User Accounts.... Click the Remove Account tab in the dialog
to present the display shown in Figure 4-2. Select the account (login) name from the list of accounts at the top of the dialog and click the Remove Account button.
0
Figure 4-2. User Account Administration Dialog – Remove Account
4-4 59056-02 A
0
4.1.3

Changing a User Account Password

To change the password for an account on a switch, open the Switch menu in the
faceplate display and select User Accounts.... Click the Change Password tab
in the dialog to present the display shown in Figure 4-3. Select the account (login) name from the list of accounts at the top of the dialog, then enter the old password, the new password, and verify the new password in the corresponding fields. Click the Change Password button. Any user can change their password for their account, but only the Admin account name can change the password for another user’s account. If the administrator does not know the user’s original password, the administrator must remove the account and add the account.
4 – Managing Switches
Managing User Accounts
Figure 4-3. User Account Administration Dialog – Change Password
59056-02 A 4-5
4 – Managing Switches Managing User Accounts
4.1.4

Modifying a User Account

To modify a user account on a switch, open the Switch menu in the faceplate
display and select User Accounts.... This displays the User Account
Administration dialog shown in Figure 4-4. Click the Modify Account tab. Select the account (login) name from the list of accounts at the top of the dialog. Click the Admin authority Enabled check box to grant admin authority to the account name. Click an Account Expiration Date radio button. If the account is not to be permanent, enter the number of days until the account expires. Click the Modify Account button to save the changes. Click the Close button to close the User Account Administration dialog.
0
Figure 4-4. User Account Administration Dialog - Modify Account
4-6 59056-02 A
0
4.2

Displaying Switch Information

The faceplate display and data windows provide the following switch information:
Device and HBA information
Switch specifications and addresses
Configuration parameters
Port performance statistics
Port information
Configured zone sets
Figure 4-5 shows the faceplate display for the SANbox 5200 Series switch.
4 – Managing Switches
Displaying Switch Information
Figure 4-5. Faceplate Display - Switch Information
The fabric updates the topology and faceplate displays by forwarding changes in status to the management workstation as they occur. You can allow the fabric to update the switch status, or you can refresh the display at any time. To refresh switch status in the display, do one of the following:
Click the Refresh button.
Open the View menu and select Refresh.
Press the F5 key.
Right-click a switch in the topology display and select Refresh Switch from
the popup menu.
Right-click in the graphic window of the faceplate display, and select
Refresh Switch from the popup menu.
59056-02 A 4-7
4 – Managing Switches Displaying Switch Information
4.2.1

Devices Data Window

The Devices data window displays information about devices (hosts and storage targets) connected to the switch. Click the Devices tab below the data window to display name server information for all devices that are logged into the selected fabric. To narrow the display to devices that are logged into specific switches, select one or more switches in the fabric tree or the topology display. Refer to
”Devices Data Window” on page 3-15 for a description of the entries in the
Devices data window.
4.2.2

Switch Data Window

The Switch data window displays current network and switch information for the selected switches. Refer to ”Configuring a Switch” on page 4-17 for more information about the Switch data window. To open the Switch data window, select one or more switches in the topology display, or open the faceplate display, and click the Switch tab below the data window. Table 4-2 describes the Switch data window entries.
0
Table 4-2. Switch Data Window Entries
Entry Description
First Port Address Switch Fibre Channel address
World Wide Name Switch World Wide Name
Serial Number Number assigned to each chassis. Required for license
keys
Reason for Status Additional status information
User Name Account name
Login Level Authority level
Super User Super user privileges enabled/disabled
UserAuthentication Enabled
Vendor Switch manufacturer
Firmware Version Active firmware version
Inactive Firmware Version Inactive firmware version
Pending Firmware Version Firmware version that will be activated at the next reset
Enforcement of account names and authority (always True)
PROM/Boot Version PROM boot version
4-8 59056-02 A
0
4 – Managing Switches
Displaying Switch Information
Table 4-2. Switch Data Window Entries (Continued)
Entry Description
MAC Address Media Access Control address
IP Address Internet Protocol address
Subnet Mask Mask that determines the IP address subnet
Gateway Gateway address
SNMP Enabled SNMP enabled or disabled.
Negotiated Domain ID The domain ID currently being used by the fabric
Configured Domain ID The domain ID defined by network administrator
Domain ID Lock Domain ID lock status. Prevents (True) or permits (False)
dynamic domain ID reassignment.
Number of Ports Number of ports activated on the switch.
Switch Type Switch model
Operational State Switch operational state: Online, Offline, Diagnostic
Administrative State Current switch administrative state
Configured Admin State Switch administrative state that is stored in the switch
configuration
R_A_TOV Resource allocation timeout value
E_D_TOV Error detect timeout value
Interop Mode Zoning merge status. If True, changes to the active zone
set are propagated throughout the fabric. If false, changes to both the active zone set and zoning database are propagated throughout the fabric. Refer to the QLogic Switch Interoperability Guide found on the QLogic Web site.
Legacy Address Format Legacy port addressing status. Enabled only for
interoperability with non-FC-SW-2 compliant switches.
Interop Auto Save Zoning auto save status. Saves zoning updates in
temporary memory and the zoning database (True) or only in temporary memory (False).
Zoning Default Visibility Zoning visibility status. Permits (All) or prevents (None)
communication between attached devices in the absence of an active zone set.
Temperature Internal switch temperature °C
59056-02 A 4-9
4 – Managing Switches Displaying Switch Information
Security Auto Save N/A - does not apply to this switch
0
Table 4-2. Switch Data Window Entries (Continued)
Entry Description
Security Fabric Binding Enable
Fan 1 Status The status of Fan 1 (SANbox 5202 only)
Fan 2 Status The status of Fan 2 (SANbox 5202 only)
Power Supply 1 Status Power supply 1 status
Power Supply 2 Status Power supply 2 status (SANbox 5202 only)
Beacon Status Beacon status. Switch LEDs are blinking (On) or not (off).
Broadcast Support Broadcast support status. Broadcast support is enabled or
In-band Enabled In-band management status. Permits (True) or prevents
Temperature Failure Port Shutdown
Warning Temperature Non-configurable temperature threshold (65° Celsius)
Failure Temperature Non-configurable temperature threshold (70° Celsius)
N/A - does not apply to this switch
disabled (default).
(False) a switch from being managed over an ISL.
Non-configurable (always enabled for this switch). All ports are downed when the switch temperature exceeds the Failure Temperature.
above which a warning condition alarm is generated.
above which a failure condition alarm is generated.
NTP Client Enabled Enabled or disabled. Allows for switches to synchronize
their time a centralized server.
NTP Server Address The IP address of the centralized NTP server. Ethernet
connection to NTP server is required.
FDMI HBA Entry Limit Maximum number of HBAs that can be registered with a
switch.
FDMI Enable Fabric Device Management Interface status. If enabled,
device information can be obtained, managed, and saved through the fabric using Name Service Management Server functions. SANsurfer Switch Manager will report any and all FDMI information reported by the entry switch, if FDMI is enabled on the entry switch. Refer to
”Displaying Detailed Device Information” on page 3-17 for
information about displaying FDMI information.
4-10 59056-02 A
0
Table 4-2. Switch Data Window Entries (Continued)
Entry Description
Number of Donor Groups Total number of donor port groups. A donor group is a set
Embedded GUI SANsurfer Switch Manager web applet status. Enables or
Inactivity Timeout Number of minutes the switch waits before terminating an
4.2.3

Port Statistics Data Window

The Port Statistics data window displays port performance data for the selected ports. To open the Port Statistics data window, click the Port Stats tab below the data window in the faceplate display. Refer to Ta ble 5- 6 for a description of the Port Statistics data window entries.
4 – Managing Switches
Displaying Switch Information
of (1-Gbps/2-Gbps only) ports on a switch that can donate buffer credits to each other.
disables the web applet on the switch.
idle command line interface session. Zero (0) disables the time out threshold.
The Statistics pull-down menu is available on the Port Statistics data window, and provides different ways to view detailed port information. Click the down arrow to open the pull-down menu. Open the pull-down menu and select Absolute to view the total count of statistics since the last switch reset. Select Rate to view the number of statistics counted per second over the polling period. Select Baseline to view the total count of statistics since the last time the baseline was set. Click the Clear Baseline button to set the current baseline.
4.2.4

Port Information Data Window

The Port Information data window displays port detail information for the selected ports. To open the Port Statistics data window, click the Port Info tab below the data window in the faceplate display. Refer to Ta ble 5- 6 for a description of the Port Information data window entries.
59056-02 A 4-11
4 – Managing Switches Displaying Switch Information
4.2.5

Configured Zonesets Data Windows

The Configured Zonesets data window displays all zone sets, zones, aliases, and zone membership in the zoning database, as shown in Figure 4-6. To open the Configured Zonesets data window, click the Configured Zonesets tab below the data window in the faceplate display. To view the active zone set in the Active Zonesets data window, open the topology display and click the Active Zonesets data window tab.
The Configured Zonesets data window uses display conventions for expanding and contracting entries that are similar to the fabric tree. An entry handle located to the left of an entry in the tree indicates that the entry can be expanded. Click this handle or double-click the following entries to expand or collapse them:
A zone set entry expands to show its member zones.
A zone entry expands to show its members by device port World Wide
Name, or device port Fibre Channel address.
The alias entry expands to show its entries.
0
Figure 4-6. Configured Zonesets Data Window
4-12 59056-02 A
Loading...