Qasair LIV15003T, D400L1, D500L2 Installation Guide

ISLAND

INSTALLATION & USER

INSTRUCTIONS

Qasair Rangehoods Installation Instructions2

Important Information

Instructions for Models

4F / PRE / FRA / MA / SQ 420 / MOL / FPR / BUR / BEL

Instructions for Models

D 400 / D 500 / SEN

Instructions for Models

TR CT / LIV

4

6

20

23

Remote Switching Specications

Ducting Pieces

Installation Ideas

Operation Details, Rangehood Cleaning, Filter Cleaning

Appliance Guarantee

Guarantee Exclusions

Standard Warranty / Extended Warranty

26

29

42

47

48

49

50

Qasair Rangehoods Installation Instructions

3

IMPORTANT INFORMATION

The installation of QASAIR Rangehoods must comply with the information in this booklet. QASAIR Rangehoods are

designed and made to work efciently over all domestic cookware available on the Australian market.

Clearance from cooktop to Rangehood

For electric hot plate cooktops

As there are no regulations for Rangehoods over an electric hot plate, please follow the manufacturers Instructions /

Recommendations.

For Induction cooktops

Induction cooktops may present problems with condensation on lters of Rangehoods.
All Qasair Rangehoods installed above an induction cooktop must be installed no less than 750mm between the

induction cooktop and the Rangehood, with the exception of the Eastmore (EAS) Rangehood which can be installed

no less than 600mm. Undermount (NDCH) and Conley (CON) Rangehoods are not suitable for induction cooktops.

For gas cooktops

All Qasair Rangehood installations over a gas appliance must comply with (AS/NZS 5601.1).

The Regulations for the installation of Gas Appliances (AS/NZS 5601.1) states that the clearance between the
highest part of the burner of a gas cooking appliance and a Rangehood be no less than 600mm. If the gas
appliance is designed for use without a cooking vessel like an indoor barbecue or open ame grill, then the
clearance from the cooking surface to the Rangehood shall be no less than 1200mm.

All Qasair Rangehoods installed above a gas cooktop must be installed no less than 600mm between the highest

part of the burner and the Rangehood.

The recommendation for Qasair Wallmount Rangehoods is that they be installed between 700 to 800mm above the

highest part of the burner. When the Rangehood is installed in a galley or partially enclosed kitchen the Rangehood

can be installed between 900 to 1000mm above the highest part of the burner.

Qasair Island Rangehoods should not be installed any higher than 800mm above the highest part of the burner as
any movement around the bench will result in fumes being drawn out from the catchment area of the Rangehood
with the exception of the Thermidor and Liverpool which for aesthetic reasons is installed ush with the ceiling.

Ducting

1. Every QASAIR Rangehood must be ducted to the outside atmosphere by the use of zinc-alume duct or

non-porous and non-ammable materials. Do not use of any type of exible ducting or plastic PVC piping.
Rangehoods must not be vented into a wall cavity or a ceiling space. Externally ducting the rangehood prevents
a build up of grease, which can be a re risk. Ensure the external outlet vent does not restrict the airow in any

way, as this may result in reduced performance.

2. QASAIR Rangehoods must be ducted in duct work equivalent to the outlet of the rangehood ie: The cross
sectional area of the rangehood outlet and the duct work must be equal. Do not reduce the duct size or have
sharp bends. Enlarge the duct size if the duct is to run 6 metres or longer. Advice from CONDARI is available to
ensure optimum performance. Always use nonammable materials to minimise the risk of re in the duct.

3. Ensure all ducting pieces are correctly tted and sealed with either duct tape or silicone to ensure that fumes
do not escape into the ceiling space and seep into living areas through vents or light ttings.

Qasair Rangehoods Installation Instructions4

Other Important Information

1. Always adequately ventilate the room when the rangehood is in use at the same time as appliances

burning gas or other fuels.

2. WARNING: Incorrect venting will result in additional noise and a reduction in efciency. Exhaust air must not be

discharged into any chimney or ue, which may carry combustible products from other sources.
a) Do not discharge the air-ow from the rangehood into a ue used for exhausting fumes

from burning gas or fuel;
b) For cleaning purposes please refer to page 47 of installation instructions for stainless steel;

c) If cleaning is not carried out in accordance with the instructions as listed on page 47, there may be an
increased risk of re;

d) Some parts of the rangehood may become hot when cooking;
e) This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person responsible for their safety.

3. The installation and tting of the rangehood should be done in such a way that will allow the unit to be removed
if service is required. Additional costs incurred in the removal of wall tiles, damage to walls or bench tops are not
covered by warranty.

4. To reduce the risk of xing screws coming in contact with live parts, do not drill or screw into the rangehood.
Live wires are encapsulated where possible to prevent user contact. If necessary drill from the inside out and

only through single sheet material.

5. NOTE: CONDARI recommend an air movement of between 1000 to 1400 cubic metres per hour over an indoor
barbecue, depending on the length of the duct run. Ensure a twin motor unit is installed over indoor barbecues

for optimum results. Barbecues should be positioned under the centre of the hood where the fans are mounted
and not near the outer edges where leakage may occur.

6. The lights in the rangehoods are LED and come with a night light except for D400L-1 and SEN400L-1.

7. If the supply cord is damaged, an authorised service centre or licensed electrician must replace it.

8. Do not ambé under the rangehood.

9. QASAIR domestic rangehoods must not to be used over barbecues approved for outdoor use only,
CONDARI make a range of hoods specically for outdoor barbecues in alfresco areas under the CONDOR

name.

10. CONDARI can manufacture rangehoods to be used over commercial cookers in domestic applications.

12. NOTE: Ensure all requirements are met with gas and electrical regulations and or state authorities.

Qasair Rangehoods Installation Instructions

5

INSTALLATION INSTRUCTIONS

• 4F

• PRE / FRA

• MA

• SQ 420 / MOL

• FPR

• BUR / BEL

• D 400 / D 500 / SEN

It is recommended that the rangehood be mounted 100mm back from the edge of the benchtop.

1. The rangehood can be installed between 700mm and 800mm above the cooking surface. The installer should
check for local requirements in case additional provisions apply.

2. It is advisable to remove fans for easier handling of unit by removing retaining bolts or clips and unplugging

electrical connector.

3. Measure hole centres and duct size on top of the rangehood. This will vary with the hood size, model and

number of fans fitted and will determine the ducting required.

4. Using a plumb line, mark the ceiling before making the cut out. Check for obstructions like electrical cables etc.

5. Cut two (2) supporting beams approximately 1.0m long and pre-drill hole centres so that the supporting beams
are 90 degrees to the ceiling joists.

6. Fit 8mm all thread (threaded rod) through holes provided and secure with nuts and washers.

7. Level unit by tensioning the 8mm nuts. Do not over tighten.

8. Fit off ducting as required.

Installation Suggestions

1) 2)

6

Qasair Rangehoods Installation Instructions

4 Flare

Technical Specification Sheet

4F

Ceiling Mounted

4 FLARE - 4F

B

o

d

y

F

l

u

e

W

i

d

t

h

A

l

l

-

T

h

r

e

a

d

0

6

2

250
210

W

i

d

t

h

Ø15mm Radius

H

Power Entry

5

1

1

d

a

e

r

h

T

-

l

l

A

480

F

l

u

e

W

i

d

t

h

B

o

d

y

W

i

d

t

h

700

80

Power Entry

0

6

A

l

l

-

T

h

r

e

a

d

2

5

1

1

a

e

r

h

T

-

l

l

A

Ø15mm Radius

A Transition is supplied to suit standard DL2 ducting.

Model 4F 1000L-2 4F 1200L-2

Body Width

Motor Box /
Flue Width

Motor Qty

LED Light

Nightlight

Light Qty

Light Centres

Filter Qty

1000mm

350mm

2

Cool

YES

2

430mm

4

1200mm

400mm

2

Cool

YES

3

380mm

6

Model4F 1200L-24F 1000L-2

Filter Size

Conversion
Top/Back Back/Top

Electrical Connection

Minimum Height
(H =)

Maximum Height
(H =)

PowderKote
Available
All-thread
Fixing Centres

Corner Type

Condari Pty Ltd.



429mm x 260mm

N/A

10 Amp Lead

480mm

1660mm

YES

300mm x 200mm

Round

Version: D 20/03/2017F

355mm x 250mm

N/A

10 Amp Lead

480mm

1660mm

YES

350mm x 200mm

Round

Page 1 of 1

d

Qasair Rangehoods Installation Instructions

7

President

Technical Specification Sheet

PRE

Ceiling Mounted

Model

Body Width

Motor Box /
Flue Width

PRE 1000L-2

Condari Pty Ltd.

Corner Type

Motor Qty

Nightlight

Light Qty

All-thread
Fixing Centres

Maximum Height
(H =)

6

380mm430mm

Cool

4

Filter Qty

Light Centres

LED Light

360mm x 320mm 360mm x 320mm

1600mm

YES

429mm x 260mm

PRE 1000L-2

Electrical Connection

NO

550mm

10 Amp Lead

Version: D 28/03/2017F

Round

550mm

YES

Page 1 of 2

Round

1000mm

420mm

2

YES

2

PRE 1200L-2 Model

1600mm

NO

10 Amp Lead

PowderKote



Available

Minimum Height
(H =)

3

Cool

YES

2

1200mm

420mm

Filter Size

Conversion
Top/Back Back/Top

PRE 1200L-2

355mm x 250mm

Power Entry

B

o

d

y

W

i

d

t

h

100

H

85 85250

420

1

4

0

M

o

t

o

r

B

o

x

W

i

d

t

h

2

5

0

A

l

l

-

T

h

r

e

a

d

A

l

l

-

T

h

r

e

a

d

5

0

700

Ø15mm Radius

5

0

B

o

d

y

W

i

d

t

h

M

o

t

o

r

B

o

x

W

i

d

t

h

Power Entry

2

5

0

A

l

l

-

T

h

r

e

a

d

1

4

0

A

l

l

-

T

h

r

e

a

d

5

0

5

0

Ø15mm Radius

PRESIDENT - PRE

Qasair Rangehoods Installation Instructions8

President

Technical Specification Sheet

PRE

Ceiling Mounted

ModelPRE 1800L-3PRE1500L-3Model

Body Width

Nightlight

Light Qty

Minimum Height
(H =)

All-thread
Fixing Centres

Light Centres

LED Light

Filter Qty

Motor Qty

Motor Box /
Flue Width

Corner Type

Maximum Height
(H =)

Electrical Connection

Conversion
Top/Back Back/Top

Condari Pty Ltd.

PowderKote



Available

Filter Size

Page 1 of 2

3

Cool

YES

8

510mm

3

1500mm

900mm 900mm

1800mm

4

Cool

3

422mm

10

YES

840mm x 320mm

Round

YES

840mm x 320mm

YES

1600mm

PRE 1800L-3

10 Amp Lead

550mm

PRE 1500L-3

NO

340mm x 260mm

NO

340mm x 260mm

10 Amp Lead

Round

Version: D 28/03/2017F

1600mm

550mm

250

85

H

100

B

o

d

y

W

i

d

t

h

B

o

d

y

W

i

d

t

h

85

1

4

0

M

o

t

o

r

B

o

x

W

i

d

t

h

M

o

t

o

r

B

o

x

W

i

d

t

h

420

A

l

l

-

T

h

r

e

a

d

5

0

A

l

l

-

T

h

r

e

a

d

1

4

0

A

l

l

-

T

h

r

e

a

d

4

5

0

5

0

A

l

l

-

T

h

r

e

a

d

Power Entry

700

Ø15mm Radius

Ø15mm Radius

Power Entry

4

5

0

5

0

5

0

PRESIDENT - PRE

Qasair Rangehoods Installation Instructions

9

Franklyn

Technical Specification Sheet

FRA

Ceiling Mounted

Model

Body Width

Motor Box /
Flue Width

FRA 1000L-2

Condari Pty Ltd.

Corner Type

Motor Qty

Nightlight

Light Qty

All-thread
Fixing Centres

Maximum Height
(H =)

6

380mm430mm

Cool

3

Filter Qty

Light Centres

LED Light

360mm x 320mm 360mm x 320mm

1600mm

N/A

429mm x 260mm

FRA 1000L-2

Electrical Connection

NO

550mm

10 Amp Lead

Version: C 12/12/2017F

Square

550mm

N/A

Page 1 of 2

Square

1000mm

420mm

2

YES

2

FRA 1200L-2 Model

1600mm

NO

10 Amp Lead

PowderKote

}

Available

Minimum Height
(H =)

3

Cool

YES

2

1200mm

420mm

Filter Size

Conversion
Top/Back Back/Top

FRA 1200L-2

350mm x 250mm

Power Entry

700

100

H

85 85250

420

Front

Front

Power Entry

FRANKLYN - FRA

Qasair Rangehoods Installation Instructions10

840mm x 320mm

Square

840mm x 320mm

Square

N/A

550mm

10 Amp Lead

NO NO

1600mm

10 Amp Lead

PowderKote

}

Available
All-thread
Fixing Centres

3

Cool

1800mm

900mm

Maximum Height
(H =)

43

510mm

10

422mm

8

Cool

YES YES

900mm

1500mm

3

FRA 1500L-3

FRA 1800L-3

N/A

550mm

340mm x 260mm 340mm x 260mm

1600mm

Model

Conversion
Top/Back Back/Top

FRA 1800L-3

Corner Type

Electrical Connection

Minimum Height
(H =)

FRA 1500L-3

Condari Pty Ltd.

Filter Size

LED Light

Filter Qty

Motor Box /
Flue Width

Motor Qty

Light Centres

Light Qty

Nightlight

Model

Body Width

Version: C 12/12/2017F

Page 2 of 2

Franklyn

Technical Specification Sheet

FRA

Ceiling Mounted

Power Entry

250

85

H

100

700

85

420

Front

Front

Power Entry

FRANKLYN - FRA

Qasair Rangehoods Installation Instructions

11

Maddison

Technical Specification Sheet

MA

Ceiling Mounted

MADDISON - MA

Motor Box

Width

Flues are equally spaced

across the body width.

250 250

2020

Motor Box

Width

Power Entry.

420

250

H

Equal Equal Equal

Body Width

Model MA 2500-3000L-4

Body Width

Motor Box /
Flue Width

Motor Qty

LED Light

Nightlight

Light Qty

Light Centres

Filter Qty

MA 2000-2500L-4

2000mm-2500mm

420mm

4

YES

Varies depending on

length of rangehood

Varies depending on

length of rangehood

Varies depending on

length of rangehood

420mm

4

CoolCool

Varies depending on

length of rangehood

Varies depending on

length of rangehood

Varies depending on

length of rangehood

Model

Filter Size2500mm-3000mm

Conversion
Top/Back Back/Top

Electrical Connection

Minimum Height
(H =)

Maximum Height
(H =)

PowderKote
Available
All-thread
Fixing Centres

Corner Type

Condari Pty Ltd.

}

700

MA 2000-2500L-4

Varies depending on

length of rangehood

N/A

10 Amp Lead

550mm

1600mmYES

N/A

360mm x 250mm

Square

Version: C 31/05/2017F

Qasair Rangehoods Installation Instructions12

MA 2500-3000L-4

Varies depending on

length of rangehood

N/A

10 Amp Lead

550mm

1600mm

N/A

360mm x 250mm

Square

Page 1 of 1

150

Winton

Technical Specification Sheet

SQ 420

Ceiling Mounted

5

WINTON - SQ420

8

5

H

250

8

5

8

5

250

8

420

420

Power Entry.

Model

Body Width

Motor Box /
Flue Width

Motor Qty

LED Light

Nightlight

Light Qty

Light Centres

Filter Qty

SQ 420L-2

420mm

N/A

2

Cool

YES

1

Centre

1

Qasair Rangehoods Installation Instructions

Front

Model

Filter Size

Conversion
Top/Back Back/Top

Electrical Connection

Minimum Height
(H =)

Maximum Height
(H =)

PowderKote
Available
All-thread
Fixing Centres

Corner Type

Condari Pty Ltd.



SQ 420L-2

355mm

10 Amp Lead

520mm

1450mm

250mm X 320mm

Square

Version: B 27/11/2014F

x 250mm

NO

YES

Page 1 of 1

13

Molina

Technical Specification Sheet

MOL

Ceiling Mounted

Version: B 27/11/2014F

5

MOLINA - MOL

8

5

250

8

5

8

5

250

8

H

420

420

Model

Body Width

Motor Box /
Flue Width

Motor Qty

LED Light

Nightlight

Light Qty

Light Centres

Filter Qty

MOL 420L-2

420mm

N/A

2

Cool

YES

1

Centre

1

Front

Model

Filter Size

Conversion
Top/Back Back/Top

Electrical Connection

Minimum Height
(H =)

Maximum Height
(H =)

PowderKote
Available
All-thread
Fixing Centres

Corner Type

Condari Pty Ltd.



Power Entry.

MOL 420L-2

x 250mm

355mm

NO

10 Amp Lead

520mm

1100mm

N/A

250mm X 320mm

Square

Page 1 of 1

Qasair Rangehoods Installation Instructions14

Fremont

Technical Specification Sheet

FPR

Ceiling Mounted

Light Centres

Filter Qty

All-thread
Fixing Centres

Varies depending on

length of rangehood

Varies depending on

length of rangehood

Corner Type

Page 1 of 1

PowderKote



Available

Condari Pty Ltd.

Varies depending on

length of rangehood

YES

Varies depending on

length of rangehood

Nightlight

Light Qty

Varies depending on

length of rangehood

Varies depending on

length of rangehood

1600mm-2600mm

Model FPR 2600-3600L-2

420mm

Model

Body Width

LED Light

2

10 Amp Lead

550mm

Motor Qty

1600mm

YES

CoolCool

2

Filter Size

2600mm-3600mm

FPR 1600-2600L-2

420mm

Conversion
Top/Back Back/Top

Motor Box /
Flue Widt

h

360mm x 250mm

Square

Version: B 31/06/2017F

10 Amp Lead

360mm x 250mm

Square

FPR 1600-2600L-2

Varies depending on
length of rangehood

N/A

N/A

FPR 2600-3600L-2

N/A

Maximum Height
(H =)

Electrical Connection

Minimum Height
(H =)

N/A

Varies depending on

length of rangehood

1600mm

550mm

Power Entry.

Motor Box can be

either L/H or R/H

A

l

l

-

T

h

r

e

a

d

700

150

H

250

20

420

5

0

A

l

l

-

T

h

r

e

a

d

1

4

0

M

o

t

o

r

B

o

x

W

i

d

t

h

Support Alternatives

Rigging

Round

Square

Square w-cross brace

Ø16mm S-S Tube

25mm x 25mm SQ S-S Tube

25mm x 25mm SQ S-S Tube

These centre dimensions are

typical for all support fixings

2

8

2

8

B

O

D

Y

W

I

D

T

H

FREMONT - FPR

Qasair Rangehoods Installation Instructions

15

Burdett

Technical Specification Sheet

BUR

Ceiling Mounted

Condari Pty Ltd.

Page 1 of 2

Version: D 28/03/2017F

Power entry location

BURDETT - BUR

is the same for all

Burdett models.

Front

250

H

Model

Body Width

Motor Box /
Flue Width

Motor Qty

LED Light

Nightlight

Light Qty

Light Centres

Filter Qty

BUR 1000L-2

1000mm

N/A

2

Cool

YES

430mm

4

BUR 1200L-2

1200mm

N/A

2

Cool

YES

380mm

6

700

Model

Filter Size

Conversion
Top/Back Back/Top

Electrical Connection

Minimum Height
(H =)

Maximum Height
(H =)

PowderKote
Available
All-thread
Fixing Centres

Corner Type

}

Front

BUR 1000L-2

429mm x 260mm

NO

10 Amp Lead

400mm

1450mm

YES23

500mm x 800mm

Square

BUR 1200L-2

355mm x 250mm

NO

10 Amp Lead

400mm

1450mm

YES

500mm x 1000mm

Square

Qasair Rangehoods Installation Instructions16

Burdett

Technical Specification Sheet

BUR

Ceiling Mounted

Version: D 28/03/2017F

Page 2 of 2

Condari Pty Ltd.

Power entry location

BURDETT - BUR

is the same for all

Burdett models.

Front

H

700

Model

Body Width

Motor Box /
Flue Width

Motor Qty

LED Light

Nightlight

Light Qty

Light Centres

Filter Qty

BUR 1200L-3

1200mm

N/A

3

Cool

YES

3

380mm

6

Qasair Rangehoods Installation Instructions

BUR 1500L-3

1500mm

N/A

3

Cool

YES

3

510mm

8

Front

Model

Filter Size

Conversion
Top/Back Back/Top

Electrical Connection

Minimum Height
(H =)

Maximum Height
(H =)

PowderKote
Available
All-thread
Fixing Centres

Corner Type

}

BUR 1200L-3

355mm x 250mm

NO

10 Amp Lead

400mm

1450mm

YES

500mm x 1000mm

Square

BUR 1500L-3

340mm x 260mm

NO

10 Amp Lead

400mm

1450mm

YES

500mm x 1300mm

Square

17

Belgrad

Technical Specification Sheet

BEL

Ceiling Mounted

Condari Pty Ltd.

Page 1 of 2

Version: C 13/12/2017F

BELGRAD - BEL

Power entry location

is the same for all

Belgrad models.

H

250

Front

Model

Body Width

Motor Box /
Flue Width

Motor Qty

LED Light

Nightlight

Light Qty

Light Centres

Filter Qty

BEL 1000L-2

1000mm

N/A

2

Cool

YES

430mm

4

BEL 1200L-2

1200mm

N/A

2

Cool

YES

380mm

6

700

Model

Filter Size

Conversion
Top/Back Back/Top

Electrical Connection

Minimum Height
(H =)

Maximum Height
(H =)

PowderKote
Available
All-thread
Fixing Centres

Corner Type

}

Front

BEL 1000L-2

429mm x 260mm

NO

10 Amp Lead

400mm

1450mm

N/A23

500mm x 800mm

Square

BEL 1200L-2

355mm x 250mm

NO

10 Amp Lead

400mm

1450mm

N/A

500mm x 900mm

Square

Qasair Rangehoods Installation Instructions18

Belgrad

Technical Specification Sheet

BEL

Ceiling Mounted

Version: C 13/12/2017F

500mm x 1000mm

Square

500mm x 1300mm

Square

400mm

1450mm

10 Amp Lead

BEL 1500L-3

NO

340mm x 260mm

N/A

BEL 1200L-3

NO

355mm x 250mm

Page 2 of 2

N/A

400mm

1450mm

10 Amp Lead

Body Width

Motor Box /
Flue Width

Nightlight

Motor Qty

LED Light

Light Qty

N/A

3

Cool

YES

3

N/A

3

Cool

YES

8

510mm

3

BEL 1500L-3

1500mm

Model

1200mm

BEL 1200L-3

Filter Qty

6

Light Centres

380mm

Condari Pty Ltd.

Corner Type

PowderKote

}

Available

Conversion
Top/Back Back/Top

Filter Size

Model

Electrical Connection

Maximum Height
(H =)

All-thread
Fixing Centres

Minimum Height
(H =)

Power entry location

is the same for all

Belgrad models.

700

H

Front

Front

BELGRAD - BEL

Qasair Rangehoods Installation Instructions

19

Albany

Technical Specification Sheet

D

Ceiling Mounted

Power Entry.

D 400L-1 / SEN 400L-1
D 500L-2 / SEN 500L-2

1. Remove Rangehood from packaging and place on a at clean surface.

2. Remove the lter.

3. Remove the four screws in the corners of the lter apperture.

4. Gently pull the base from the tube.

5. Once removed, the power supply and fan plug becomes visible. Disconnect and

place the base assembly to one side.

6. Place the four lengths of All-thread Rod through the holes in the hood and (make

sure the seam is facing the right direction) secure through a brace in the ceiling.
Feed the plug and cord into the ceiling space.

7. Fit nuts to top and bottom of All-thread Rods and tighten.

8. Reconnect the power plug and reinstall base assembly.

9. Connect power supply in ceiling and test Rangehood.

10. Fit off ducting as required

All

-

Threa

d

0

d
a
e

r

h
T

-

l

l

A

235

Bod

y Diamete

9
0

1
1

Power Entry.

r

d
a
e

r

h
T

-

l

l

A

All-Threa

Bod

250

y Diamete

d

0
5
2

r

Qasair Rangehoods Installation Instructions20

Albany

Technical Specification Sheet

D

Ceiling Mounted

Page 1 of 1

Condari Pty Ltd.

Version: A 01/07/2014F

ALBANY - D

All

-

Threa

d

0
9

d
a
e

r

h
T

-

l

l

A

0
1
1

Power Entry.

d
a
e

r

h
T

-

l

l

A

All-Threa

d

0
5
2

235

Bod

y Diamete

Model D 500L-2

Body Diameter

Motor Box /
Flue Width

Motor Qty

LED Light

Nightlight

Light Qty

Light Centres

Filter Qty

D 400L-1

400mm

N/A

1

NO

1

Centre

1

r

N/A

2

CoolCool

YES

1

Centre

1

Model

Filter Size500mm

Conversion
Top/Back Back/Top

Electrical Connection

Minimum Height
(H =)

Maximum Height
(H =)

PowderKote
Available
All-thread
Fixing Centres

Corner Type



Bod

250

y Diamete

D 400L-1

272mm

N/A

10 Amp Lead

550mm

1500

N/A

300mm

N/A

r

x 272mm

m

m

x 160mm

Power Entry.

D 500L-2

x 290mm

379mm

N/A

10 Amp Lead

650mm

1500mm

N/A

x 160mm

410mm

N/A

Qasair Rangehoods Installation Instructions

21

Seneca

Technical Specification Sheet

SEN

Ceiling Mounted

Version: A 01/07/2014F

SENECA - SEN

All

-

Threa

d

0
9

d
a
e

r

h
T

-

l

l

A

0
1
1

Power Entry.

d
a
e

r

h
T

-

l

l

A

All-Threa

d

0
5
2

235

Bod

y Diamete

Model SEN 500L-2

Body Diameter

Motor Box /
Flue Width

Motor Qty

LED Light

Nightlight

Light Qty

Light Centres

Filter Qty

SEN 400L-1

400mm

N/A

1

NO

1

Centre

1

r

N/A

2

CoolCool

YES

1

Centre

1

Model

Filter Size500mm

Conversion
Top/Back Back/Top

Electrical Connection

Minimum Height
(H =)

Maximum Height
(H =)

PowderKote
Available
All-thread
Fixing Centres

Corner Type

Condari Pty Ltd.



Bod

250

y Diamete

SEN 400L-1

272mm

N/A

10 Amp Lead

550mm

1100

N/A

300mm

N/A

r

x 272mm

m

m

x 160mm

Power Entry.

SEN 500L-2

x 290mm

379mm

N/A

10 Amp Lead

650mm

1100mm

N/A

x 160mm

410mm

N/A

Page 1 of 1

Qasair Rangehoods Installation Instructions22

INSTALLATION INSTRUCTIONS

• TR CT (REMOTE SWITCHED)

Installation must be carried out by the procedure outlined.
Failure to do so may void the guarantee.
Electrical: Wiring to the appliance must comply with State and local Regulations.
Connection to be carried out by a registered electrician.

• LIV (REMOTE SWITCHED)

1. Remove hood from packaging being careful not to touch the stainless steel front.

2. Locate centre of stove and using level or plumb line, mark centre line up to the ceiling.

3. In a new house the hood can be fixed into the ceiling space by bolting or screwing into the ceiling joists or by
building a frame to support the hood.

4. In an existing home, a hole must be cut into the ceiling and pushing the hood into the space. Ensure there are no
obstructions to placing the hood in position. In these cases a ceiling flange in stainless can be supplied to finish
the hood to the ceiling. It is not supplied in colours.

5. The outlets are either top or back ducted and can be changed on site and the hood can be reversed to suit the

intended ducting direction.

6. Once secure in position standard ducting pieces can be used.

7. Switches are not provided and remote switching in a convenient position must be installed. The switching used
must be an electrically approved switch and is not provided by Condari Pty Ltd.

8. The TR CT can be wired with either individual fan control or one pair of switches to control all fans together.

Contact Condari for further information

Qasair Rangehoods Installation Instructions

23

Thermidor

Technical Specification Sheet

TR CT

Ceiling Cavity Mounted

Page 1 of 1

Condari Pty Ltd.

Version: B 03/12/2014F

THERMIDOR - TR CT

Power entry location
is the same for all
Thermidor models.

2

0

110

110

2

0

350

600

This view is shown with grills
removed to expose filters.

Model TR CT 1500-3

Body Width

Motor Box /
Flue Width

Motor Qty

LED Light

Nightlight

Grill Qty

Grill Size

Filter Qty

TR CT 1200-3

1200mm

N/A

3

NO

2

598mm x 596mm

4

N/A

3

NONO

3

498mm x 596mm

5

Model

Filter Size1500mm

Conversion
Top/Back Back/Top

Electrical Connection

Minimum Height
(H =)

Maximum Height
(H =)

PowderKote
Available
All-thread
Fixing Centres

Corner Type



TR CT 1200-3

x 480mm

290mm

YES

Remote Switching

N/A

N/ANO

N/A

N/A

Square

Optional Flange

TR CT 1500-3

x 480mm

290mm

YES

Remote Switching

N/A

N/A

N/A

N/A

Square

Qasair Rangehoods Installation Instructions24

Liverpool

Technical Specification Sheet

LIV

Ceiling Cavity Mounted

Condari Pty Ltd.

Page 1 of 1

Version: A 20/04/2017F

LIVERPOOL - LIV

Power entry locations

are the same for all

Liverpool models.

110

20

110

20

600

300

Model

Body Width

Motor Box /
Flue Width

Motor Qty

LED Light

Nightlight

Light Qty

Light Centres

Filter Qty

LIV 1200-3

1200mm

N/A

3

N/A

N/A

N/A

4

Optional Flange

LIV 1500-3

1500mm

N/A

N/A

N/A

N/A

Model

Filter Size

Conversion
Top/Back Back/Top

3

5

Electrical Connection

Minimum Height
(H =)

Maximum Height
(H =)

PowderKote
Available
All-thread
Fixing Centres

Corner Type

}

LIV 1200-3

290mm x 480mm

YES

Remote Switching

N/A

N/A

N/AN/A N/A

N/A

Square

LIV 1500-3

290mm x 480mm

YES

Remote Switching

N/A

N/A

N/A

N/A

Square

Qasair Rangehoods Installation Instructions

25

REMOTE SWITCHING SPECIFICATIONS

3 FAN (no lights)

1. Wiring to the appliance must comply with State and local regulations.

2. Switching is not provided with this unit. - The order was for the controls to be separate from the unit.

3. You may use any switching to connect the rangehood (e.g. Clipsal switches).

4. All fans must be controlled by at least one ON/OFF and one HI/LO switch.
(i.e. single or twin motor models).

5. Please refer to Wiring Diagram below for detailed wiring information.

WIRING DIAGRAM

-------------------- CABLES TO REMOTE SWITCHES --------------------

NOTES:-

ALL FANS MUST BE CONTROLLED

1. IT IS NECESSARY TO PROVIDE

BY AT LEAST ONE ON/OFF AND

AN ON/OFF AND A HIGH/LOW

ONE HI/LO SWITCH.

SWITCH FOR EACH FAN.

2. THE WIRING FOR THE FANS ARE 4 CORE ­ LOW SPEED - BROWN
HIGH SPEED - WHITE
NEUTRAL - BLUE
EARTH - GREEN

BLUE

WHITE

BROWN

GREEN

BLUE

WHITE

BROWN

GREEN

BLUE

GREEN

WHITE

JUNCTION

BOXES

BLUE

BROWN BROWN

BLACK

BLUE

BROWN

BLACK

JUNCTION

BOXES

BLUE

BROWN

BLACK

NOTE: This diagram is for reference only. A qualied elecrician must connect remote
switching to rangehood.
Reected in this drawing is the most common method of connecting the rangehood.
Be aware that Active voltage must NOT be applied to both the ‘White- High’ or
‘Brown-Low’ wires at the same time. This will cause the fan to fail.

Qasair Rangehoods Installation Instructions26

REMOTE SWITCHING SPECIFICATIONS

‘Brown-Low’ wires at the same time. This will cause the fan to fail.

3 FAN, LED and NIGHTLIGHT

1. Wiring to the appliance must comply with State and local regulations.

2. Switching is not provided with this unit. - The order was for the controls to be separate from the unit.

3. You may use any switching to connect the rangehood (e.g. Clipsal switches).

4. All fans must be controlled by at least one ON/OFF and one HI/LO switch.
(i.e. single or twin motor models).

5. Please refer to Wiring Diagram below for detailed wiring information.

WIRING DIAGRAM

ALL FANS MUST BE CONTROLLED
BY AT LEAST ONE ON/OFF AND
ONE HI/LO SWITCH.

NOTE: This diagram is for reference only. A qualied elecrician must connect remote
switching to rangehood.
Reected in this drawing is the most common method of connecting the rangehood.
Be aware that Active voltage must NOT be applied to both the ‘White- High’ or

Qasair Rangehoods Installation Instructions

27

REMOTE SWITCHING SPECIFICATIONS

22/08/2013

3 FAN with LED

1. Wiring to the appliance must comply with State and local regulations.

2. Switching is not provided with this unit. - The order was for the controls to be separate from the unit.

3. You may use any switching to connect the rangehood (e.g. Clipsal switches).

4. All fans must be controlled by at least one ON/OFF and one HI/LO switch.
(i.e. single or twin motor models).

5. Please refer to Wiring Diagram below for detailed wiring information.

WIRING DIAGRAM

-------------------- CABLES TO REMOTE SWITCHES --------------------

GREEN

WHITE

BROWN

BLUE

BLACK

BROWN

BLUE

CIRCUIT DIAGRAM

AC1 AC2

LED

BLUE

BLUE

BLUE

BLUE

BROWN

BROWN

BROWN

BROWN

BLUE

BROWN

BLUE

JUNCTION

BOXES

AC2

LED

GREEN

WHITE

BROWN

BLUE

JUNCTION

BOXES

BROWN

BLACK

BLUE

AC1

GREEN

WHITE

BROWN

BLUE

JUNCTION

BLACK

BROWN

BLUE

CONDARI PTY LTD

8 Argent Place, Ringwood VIC 3134

Ph: [phone] / Fx: [phone]

BOXES

NOTE: This diagram is for reference only. A qualied elecrician must connect remote
switching to rangehood.
Reected in this drawing is the most common method of connecting the rangehood.
Be aware that Active voltage must NOT be applied to both the ‘White- High’ or
‘Brown-Low’ wires at the same time. This will cause the fan to fail.

NOTES:-

1. IT IS NECESSARY TO PROVIDE

ALL FANS MUST BE CONTROLLED BY

AN ON/OFF AND A HIGH/LOW

AT LEAST ONE ON/OFF AND ONE

SWITCH FOR EACH FAN.

HI/LO SWITCH.

2. THE WIRING FOR THE FANS ARE 4 CORE ­ LOW SPEED - BROWN
HIGH SPEED - WHITE
NEUTRAL - BLUE
EARTH - GREEN

3. THE WIRING FOR THE LIGHTS IS 2 CORE ­ ACTIVE - BROWN
NEUTRAL - BLUE

DESIGNER

M. Brewin

CHECKED

M. Malesevic REVISION

DATE

A

Qasair Rangehoods Installation Instructions28

SINGLE MOTOR DUCTING

NOTE:

This Zinc Alume Strip is provided to join some duct pieces together.

It will be clearly shown on the drawing of the piece it is supplied with.

I/I: Inside to Inside Measurement

101. DL-1 Single Motor Duct Length 1200mm
DL-1 CB Single Motor Duct

Back Draft Wall Vent Single Motor Horizontal

1200mm Colourbond

Horizontal Bend Single Motor 90º

102. HB-1

105. BD/WV-H-1 SS

445M2 Stainless Steel

Length

Single Motor Duct Length 300mm

Horizontal Bend Single Motor 45º

Vertical Bend Single Motor 90º

101. DL-1 A

103. HB-1/45

106. VB-1

Single Motor Duct Length Extension

Back Draft Wall Vent Single Motor Horizontal

See alternative Duct Piece No. 145

Vertical Bend Single Motor 45º

101. DL-1 E

104. BD/WV-H-1

107. VB-1/45

Back Draft Wall Vent Single Motor

108. BD/WV-V-1

Vertical

Qasair Rangehoods Installation Instructions

Back Draft Wall Vent Single Motor Vertical

109. BD/WV-V-1 SS

445M2 Stainless Steel

Duct Director Single Motor Horizontal Left

110. DD-1H L

29

SINGLE MOTOR DUCTING

Duct Director Single Motor Horizontal

111. DD-1H R

Right

114. CD-920

Cavity Duct Extendible

117. DR-200

Duct Length 200Ø

Twisted Transition Single Motor

Duct Length 200Ø Colourbond

112. TT-1

115. CD-920 TO DL-1

Cavity Duct to DL-1

118. DR-200 CB

113. DLE-DLE

Flue Joiner Single Motor

Single Motor Transition DL-1 to 200Ø

116. TR-1

119. DR-200/45

200Ø Bend 45º

120. DR-200/90
200Ø Bend 90º

123. CH-200

Chairman’s Hat 200Ø

Back Draft Wall Vent Rear Register Kit to

121. BD-6/7/9-WV-R/R

Suit 6/7/900H

Chairman’s Hat 200Ø Colourbond

124. CH-200 CB

122. BD/WV-200Ø

Back Draft Wall Vent

Back Draft Roof Cowl Single Motor

125. BD/RC-1

Qasair Rangehoods Installation Instructions30

SINGLE MOTOR DUCTING

Back Draft Roof Cowl Single Motor

Wall Vent Cover Single Motor Horizontal

126. BD/RC-1 CB

Colourbond

Back Draft Damper Single Motor

129. BD/M-1

132. WVC-H-1 SS

445M2 Stainless Steel

Back Draft Roof Cowl Single Motor 200Ø

Wall Vent Cover Single Motor Vertical

127. BD/SQ-RC 200

130. CF 6/7/900H

Ceiling Flange to Suit 6/7/900H

133. WVC-V-1

Stainless Steel Flue Cap to Suit DLE

Wall Vent Cover Single Motor Horizontal

Wall Vent Cover Single Motor Vertical

128. DLE-S/S CAP

131. WVC-H-1

See alternative Duct Piece No. 145

134. WVC-V-1 SS

445M2 Stainless Steel

135. 6/7/900H-SC

Spiggot Cap to Suit 6/7/900H

Roof Cap 200Ø 445M2 Stainless Steel

138. RCP 200 SS

Qasair Rangehoods Installation Instructions

136. EV/DL-1

Eave Vent to Suit DL-1

Roof Cowl 200Ø 445M2 Stainless Steel

139. RC 200 SS

Wall Vent Cover to Suit Rear Register Kit

137. WVC-6/7/9H-R/R

for 6/7/900H

140. RC 200

Roof Cowl 200Ø

31

Roof Cowl Single Motor 445M2 Stainless Steel

400

75

250

141. RC 1 SS

WALL VENT

144. FRWV-V-1 SS

Fire Rated Wall Vent Vertical

445M2 Stainless Steel

142. FRC 200 SS

Fire Rated 200Ø Roof Cowl

445M2 Stainless Steel

I

/

I

2

4

2

4

8

0

/

I

WALL VENT

3

1

7

7

5

I

/

I

3

1

8

2

5

0

0

5

1

Back Draft Wall Vent & Cover Single Motor

Horizontal kit assembled as one piece

145. BD/WV/K-H-1

WALL VENT

143. FRWV-H-1 SS

Fire Rated Wall Vent Horizontal

445M2 Stainless Steel

0

1

1

I

ROOF COWLS, WALL VENTS

AND WALL VENT COVERS

All the above ducting pieces

are all made in stainless

steel type 445M2 which

has a chromium content of

22% which is far greater

than marine grade stainless

steel and provides better

protection.

This is stated on the
description of each piece in
the ducting brochure.

WALL VENT COVERS SPECIFICATIONS

FIRE RATED APPROVED

The wall vent covers have

stainless steel screening

type 316 and meets the
requirements for stainless

steel screening under the
Australian Standard.

AS 3959-2009 Construction

of Buildings in Bushfire
prone areas.

Qasair Rangehoods Installation Instructions32

TWIN MOTOR DUCTING

NOTE:

This Zinc Alume Strip is provided to join some duct

pieces together. It will be clearly shown on the drawing
of the piece it is supplied with.

I/I: Inside to Inside Measurement

201. TMT

Twin Motor Transition

Horizontal Bend Twin Motor 45º

204. HB-2/45

Vertical Bend Twin Motor 90º

207. VB-2

Twin Motor Duct Length 1200mm

Back Draft Wall Vent Twin Motor

Vertical Bend Twin Motor 45º

202. DL-2

205. BD/WV-H-2

Horizontal

208. VB-2/45

Horizontal Bend Twin Motor 90º

Back Draft Wall Vent Twin Motor Horizontal

203. HB-2

206. BD/WV-H-2 SS

445M2 Stainless Steel

Back Draft Wall Vent Twin Motor Vertical

209. BD/WV-V-2

Back Draft Wall Vent Twin Motor Vertical

210. BD/WV-V-2 SS

445M2 Stainlerss Steel

Qasair Rangehoods Installation Instructions

Twisted Transition Twin Motor

211. TT-2

212. DLE-2 TO DLE-2

Flue Joiner Twin Motor

33

TWIN MOTOR DUCTING

213. BD-10/12/15-WV-R/R

Back Draft Wall Vent 10/12/1500H

216. DR-300

Duct Length 300Ø

219. DR-300/90
300Ø Bend 90º

214. TMT-300

Twin Motor Transition to 300Ø

217. DR-300 CB

Duct Length 300Ø Colourbond

Twin Motor Transition DL-2 to 250SQ

220. DL-2/250SQ

Twin Motor Transition from DL-2 to 300Ø

Twin Motor Transition 250SQ to 300Ø

215. TR-2

218. DR-300/45

300Ø Bend 45º

221. TMT-250/300

Twin Motor Transition to 250SQ

222. TMT-250

225. HB-250/45

Horizontal Bend 250SQ 45º

223. DL-250

Duct Length 250SQ

226. TMT-250/90 L

Duct Deflector 250SQ Left

224. HB-250

Horizontal Bend 250SQ 90º

227. TMT-250/90 R

Duct Deflector 250SQ Right

Qasair Rangehoods Installation Instructions34

TWIN MOTOR DUCTING

228. BD/WV-250 SQ

Back Draft Wall Vent 250SQ

231. BD/RC-2 CB

Back Draft Roof Cowl Twin Motor

Colourbond

234. BD/SQ-RC 300

Back Draft Roof Cowl 300Ø

229. BD/WV-250 SQ SS

Back Draft Wall 250SQ 445M2 Stainless

Back Draft Roof Cowl 250SQ

Steel

232. CH-300

Chairman’s Hat 300Ø

235. BD/RC-250 SQ

Back Draft Roof Cowl Twin Motor

Chairman’s Hat 300Ø Colourbond

Stainless Steel Flue Cap to Suit DLE-2

230 BD/RC-2

233. CH-300 CB

236. DLE-2-S/S CAP

237. CF 10/12/1500H

Ceiling Flange to Suit 10/12/1500H

240. CF 4F-900-2

Ceiling Flange to Suit 4F 900-2

Qasair Rangehoods Installation Instructions

238. CF 3F-900-2

Ceiling Flange to Suit 3F 900-2

241. CF 4F-1200-2

Ceiling Flange to suit 4F 1200-2

239. CF 3F-1200-2

Ceiling Flange tp suit 3F 1200-2

Wall Vent Cover Twin Motor Horizontal

242. WVC-H-2

35

TWIN MOTOR DUCTING

Wall Vent Cover Twin Motor Horizontal

Spiggot Cap to Suit 10/12/1500H

243.WVC-H-2 SS

445M2 Stainless Steel

246. WVC-250 SQ

Wall Vent Cover 250SQ

249. 10/12/15H-SC

Wall Vent Cover Twin Motor Vertical

Wall Vent Cover 250SQ 445M2 Stainless

Duct Director Twin Motor Horizontal Left

244. WVC-V-2

247. WVC-250 SQ SS

Steel

250. DD-2H-L

Wall Vent Cover Twin Motor Vertical

Wall Vent Cover to suit 10/12/1500H

Duct Director Twin Motor Horizontal Right

245. WVC-V-2 SS

445M2 Stainless Steel

248. WVC-10/12/15H-R/R

251. DD-2H-R

Duct Director Twin Motor Vertical Left

Back Draft Damper Twin Motor 250SQ

252. DD-2V-L

255. BD/M-250SQ

Duct Director Twin Motor Vertical Right

253. DD-2V-R

256. BD/WV-300Ø

Back Draft Wall Vent

254. EV/DL-2

Eave Vent to Suit DL-2

257. BD/WVC-SBS

Twin Motor Wall Vent Deflector

Qasair Rangehoods Installation Instructions36

TWIN MOTOR DUCTING

75

400

250

EXTENDED

250

75

400

EXTENDED

6

7

5

258. CF 3F-1500-2

Ceiling Flange to Suit 3F 1500-2

Roof Cowl 300Ø 445M2 Stainless Steel

Fire Rated Wall Vent Twin Motor Horizontal

I

/

I

6

5

Kit assembled as one piece. Two Single Motor

261. RC 300 SS

264. FRWV-H-2 SS

445M2 Stainless Steel

5

2

5

3

9

5

2

5

0

0

267. BD/WV/K-H-2

Back Draft Wall Vent Horizontal

with telescopic length & cover

I

/

I

0

4

2

I

/

I

0

1

1

2

4

8

Roof Cap 300Ø 445M2 Stainless Steel

Roof Cowl Twin Motor 445M2 Stainless

259. RCP 300 SS

262. RC 2 SS

Steel

WALL VENTWALL VENT

Fire Rated Wall Vent Twin Motor Vertical

I

/

I

7

5

Kit assembled as one piece. Fire rated Two

Single Motor Back Draft Wall Vent Horizontal

265. FRWV-V-2 SS

445M2 Stainless Steel

6

5

2

6

5

3

2

5

0

0

5

268. FRWV/K-H-2

with telescopic length & cover

9

5

I

/

I

0

4

2

I

/

I

0

1

1

2

4

8

WALL VENTWALL VENT

Roof Ventilation Cowl 300Ø 445M2

260. RV 300 SS

Stainless Steel

263. FRC 300 SS

Fire Rated Roof Cowl 300Ø

445M2 Stainless Steel

WALL VENT

Fire Rated Wall Vent Twin Motor 250SQ

266. FRWV-250 SQ SS

445M2 Stainless Steel

ROOF COWLS, WALL VENTS

AND WALL VENT COVERS

All the above ducting pieces

are all made in stainless

steel type 445M2 which

has a chromium content of

22% which is far greater

than marine grade stainless

steel and provides better

protection.

This is stated on the
description of each piece in
the ducting brochure.

WALL VENT COVERS SPECIFICATIONS

FIRE RATED APPROVED

The wall vent covers have

stainless steel screening

Qasair Rangehoods Installation Instructions

type 316 and meets the
requirements for stainless

steel screening under the
Australian Standard.

AS 3959-2009 Construction

of Buildings in Bushfire
prone areas.

37

TRIPLE MOTOR DUCTING

NOTE:

This Zinc Alume Strip is provided to join some duct pieces together.

It will be clearly shown on the drawing of the piece it is supplied with.

I/I: Inside to Inside Measurement

301. 3MT-DL-3

Three Motor Transition to DL-3

Horizontal Bend Triple Motor 45º

Triple Motor Twisted Transition

304. HB-3/45

307. TT-3

302. DL-3

Triple Motor Duct Length

Vertical Bend Triple Motor 90º

Triple Motor Transition DL-3 to 350Ø

305. VB-3

308. TMT-400x200/350

Horizontal Bend Triple Motor 90º

Vertical Bend Triple Motor 45º

Triple Motor Transition to 350Ø

303. HB-3

306. VB-3/45

309. TR-3

310. DR-350

Duct Length 350Ø

311. DR-350 CB

Duct Length 350Ø Colourbond

312. DR-350/45
350Ø Bend 45º

Qasair Rangehoods Installation Instructions38

TRIPLE MOTOR DUCTING

313. DR-350/90
350Ø Bend 90º

Back Draft Roof Cowl Triple Motor 350SQ

316. BD/SQ-RC 350

319. CH-350 CB

Chairmans Hat 350Ø Colorbond

Back Draft Roof Cowl Triple Motor

Back Draft Wall Vent Triple Motor Horizontal

314. BD/RC-3

317. BD/SQ-RC 350 SS

Back Draft Roof Cowl 350Ø

445M2 Stainless Steel

320. BD/WV-H-3

Back Draft Roof Cowl Triple Motor

Back Draft Wall Vent Triple Motor Horizontal

315. BD/RC-3 SS

445M2 Stainless Steel

318. CH-350

Chairmans Hat 350Ø

321. BD/WV-H-3 SS

445M2 Stainless Steel

Back Draft Wall Vent Triple Motor Vertical

Wall Vent Cover Triple Motor Horizontal

322. BD/WV-V-3

325.WVC-H-3 SS

445M2 Stainless Steel

Qasair Rangehoods Installation Instructions

Back Draft Wall Vent Triple Motor Vertical

Wall Vent Cover Triple Motor Vertical

323. BD/WV-V-3 SS

445M2Stainless Steel

326. WVC-V-3

Wall Vent Cover Triple Motor Horizontal

Wall Vent Cover Triple Motor Vertical

324. WVC-H-3

327. WVC-V-3 SS

445M2 Stainless Steel

39

TRIPLE MOTOR DUCTING

0

75

EXTENDED

9

I

1

EXTENDED

9

5

I

Duct Director Triple Motor Vertical Left

328. DD-3V-L

WALL VENT

331. FRWV-H-3 SS

Fire Rated Wall Vent Triple Motor

/

I

9

8

8

7

5

Kit assembled as one piece. Three Single

Motor Back Draft Wall Vent Horizontal

with telescopic length & cover

Horizontal

8

7

9

5

0

334. BD/WV/K-H-3

9

5

I

/

I

0

4

2

I

/

I

0

1

1

2

4

8

2

5

0

WALL VENT WALL VENT

Duct Director Triple Motor Vertical Right

329. DD-3V-R

WALL VENT

Fire Rated Wall Vent Triple Motor Vertical

/

I

7

5

Kit assembled as one piece. Fire rated Three

Single Motor Back Draft Wall Vent Horizontal

332. FRWV-V-3 SS

8

7

9

8

8

9

5

0

5

335. FRWV/K-H-3

with telescopic length & cover

9

5

I

/

I

0

4

2

I

/

I

1

1

2

4

8

2

5

0

330. BD/WV-350Ø

Back Draft Wall Vent

Fire Rated Roof Cowl 350Ø 445M2

333. FRC 350 SS

Stainless Steel

ROOF COWLS, WALL VENTS

AND WALL VENT COVERS

All the above ducting pieces

are all made in stainless

steel type 445M2 which

has a chromium content of

22% which is far greater

than marine grade stainless

steel and provides better

protection.

This is stated on the
description of each piece in
the ducting brochure.

WALL VENT COVERS SPECIFICATIONS

FIRE RATED APPROVED

The wall vent covers have

stainless steel screening

type 316 and meets the
requirements for stainless

steel screening under the
Australian Standard.

AS 3959-2009 Construction

of Buildings in Bushfire
prone areas.

Qasair Rangehoods Installation Instructions40

450 x 250 DUCTING

NOTE:

This Zinc Alume Strip is provided to join some duct pieces together.

It will be clearly shown on the drawing of the piece it is supplied with.

All 450 x 250 Duct Pieces can be supplied in Stainless Steel (SS)
and Colorbond/Powdercoat (C/P), just add SS or C/P to the part
number. Eg. DL-4SS.

I/I: Inside to Inside Measurement

450 x 250 Duct Length 1200

Horizontal Bend 450 x 250 45º

Back Draft Wall Vent 450 x 250 Vertical

400. DL-4

403. HB-450X250/45

406. BD/WV-V-450X250

401. HB-450X250

Horizontal Bend 450 x 250 90º

404. VB-450X250/45

Vertical Bend 450 x 250 45º

407. RCB

Roof Cowl 450 x 250

402. VB-450X250

Vertical Bend 450 x 250 90º

Back Draft Wall Vent 450 x 250 Horizontal

405. BD/WV-H-450X250

408. RCBA

Roof Cowl 450 x 250

409. WCV-H-450X250

Wall Vent Cover 450 x 250 Horizontal

Qasair Rangehoods Installation Instructions

410. WCV-V-450X250

Wall Vent Cover 450 x 250 Vertical

Back Draft Roof Cowl 450 x 250

411. BD/RC-4

41

INSTALLATION IDEAS

Condari recommends Qasair and Condor Rangehoods be installed using ducting that is:

• rigid

• non-ammable

• correctly sized
to ensure maximum air movement and minimum noise levels.

Ducting incorrectly with exible or smaller diameter ducting will dramatically reduce the air movement
and increase the noise level of the rangehood and will void the manufacturer’s warranty.

The Installation Ideas below will give you some guidelines on how to correctly duct your Qasair and

Condor Rangehood using Qasair and Condor ducting pieces.

FA 60L-1 T
Rangehood

3. FA 60L-1 T 4. FA 60L-1 T

FA 60L-1 T
Rangehood

5. FA 60L-1 T

6. FA 60L-1 T / FA 60L-1 B

FA 60L-1 T
Rangehood

FA 60L-1 T
FA 60L-1 B
Rangehood

Qasair Rangehoods Installation Instructions42

FA 90L-2 T
Rangehood

FA 90L-2 T
Rangehood

7. FA 90L-2 T 8. FA 90L-2 T

FA 90L-2 B
Rangehood

FA 90L-2 T
Rangehood

9. FA 90L-2 T 10. FA 90L-2 B

FA 90L-2 T
Rangehood

11. FA 90L-2 T 12. FA 90L-2 T

Qasair Rangehoods Installation Instructions

FA 90L-2 T
Rangehood

43

600HL-1 T / 700HL-1 T / 900HL-1 T
Rangehood

13. 600HL-1 T / 700HL-1 T / 900HL-1 T 14. 600HL-1 T

600HL-1 T Rangehood

CON 60L-1 T Rangehood

15. CON 60L-1 T 16. CON 80L-1 T

17. CON 60L-1 T 18. CON 80L-2 T

CON 80L-1 T Rangehood

CON 80L-2 T RangehoodCON 60L-1 T Rangehood

Qasair Rangehoods Installation Instructions44

1200HL-2 T
Rangehood

19. 1200HL-2 T 20. LIS 800L-2 T

LIS 800L-2 T
Rangehood

21. LIS 1000L-2 T 22. 3F 900L-2 T / 1200L-2 T

LIS 500L-1 T
Rangehood

23. LIS 500L-1 T 24. LIS 800L-1 T

Qasair Rangehoods Installation Instructions

LIS 1000L-2 T
Rangehood

3F 900L-2 T / 1200L-2 T
Rangehood

LIS 800L-1 T
Rangehood

45

LIS 1200L-2 B
Rangehood

CON 80L-1 T
Rangehood

FA-90L-1 T
Rangehood

LIS 1000L-2 T
Rangehood

25. CON 80L-1 T / LIS 1000-2 T 26. LIS 1200L-2 B

FA-60L-1 B
Rangehood

1. FA 60L-1 B2. FA 90L-1 T

Qasair Rangehoods Installation Instructions46

OPERATION DETAILS

Light ON and OFF

Light High and Low

Fan Left Side ON and OFF

Fan Left Side High and Low

Right Side Fan/s ON and OFF

Right Side Fan/s High and Low

RANGEHOOD CLEANING

Qasair Rangehoods are made from stainless steel, either type 304 or type 316.
* Type 304 is classied as 18/8 stainless steel
* Type 316 is classied as 18/10 stainless steel
This means that the stainless steel is made of 18% nickel and either 8% or 10% of chromium respectively.
Stainless steel gets its protective coating from the chromium oxidising in the air to form a protective surface

of chromium oxide. This can be attacked by different substances, such as salt water or sea air. The stainless
steel will start to show pit marks which are referred to in the industry as tea staining. This will happen to

marine grade stainless steel type 316 in the same way it will happen to stainless steel type 304, it will just

take longer to happen.

The way to overcome this is to clean the stainless steel with warm soapy water and then polish it with a cloth

so that the chromium will oxidise again.
When exposed to sea water or sea side conditions this is only a stop gap measure as the attack will start
again.

With stainless steel rangehoods exposed in Alfresco areas we recommend spraying the hood with vegetable
oil and rubbing it all over the rangehood, if it is going to be unused over a period of time.

FILTER CLEANING

For the best results, please clean filters regularly.
Condari recommends cleaning filters once per month, or immediately after heavy use.
You can do this by hand washing in warm soapy water, or by placing filters in the top rack of the
dishwasher using a detergent of pH 8 or less.
Note: Washing the filters in the dishwasher may cause discolouration of the filters.

We recommend washing filters in the dishwasher without detergent or use one of the powder

detergent.
Ensure the filters are completely dry before placing them back.
Do not operate the rangehood without the filters installed.
Condari does not recommend the use of corrosive, caustic or acidic products, particulary industrial
or citric products.
Condari has experienced problems with many of the dishwashing detergents now on the market.
Particularly with the tablet type detergents as many come from overseas, which are made for a hard
water environment. We have found that these detergents have a deleterious effect on the filters and
the result is that the filters last for about 50 to 60 washes.
This is equivalent to about 5 to 6 years life.

Qasair Rangehoods Installation Instructions

47

CONDARI PTY LTD APPLIANCE GUARANTEE

The benefits conferred by this warranty are in addition to all other rights and remedies in respect of the product

which the consumer has under the Competition and Consumer Act 2010 and similar state and territory laws.

Condari P/L in Melbourne (and by their agency in Country Areas and other States) warrants that the appliance
will be free from defects in materials and workmanship for a period of 36 months from the date of purchase of
the appliance to the consumer.

If there is a breach of this warranty, Condari will rectify, free of charge, at it’s nearest service centre or
authorised service agency any fault caused by faulty workmanship or material at the time of manufacture

occurring in the appliance within 36 months from the date of purchase of the appliance to the customer.

This warranty is conditional upon the appliance being used only for personal, domestic and household purposes
and installed and operated in accordance with QASAIR Instructions and does not apply to articles which by their
nature are consumable.

If a defect is caused by neglect, misuse, or failure to follow operating instructions where special precautions are
detailed for user attention then a charge shall be made for the service call.

For example:

With the filters the user is specifically requested:

• To clean filter regularly by handwashing or placing in a dishwasher at least once a month.

• To turn rangehood off after each use.

• Note: Warranty under filter cleaning on page 47.

Where a claim is made under warranty, CONDARI reserves the right to determine whether or not the fault is

caused by faulty workmanship or material or that the part is defective.

The consumer shall be fully responsible for all expenses whatsoever incidental to the removal of parts from

the unit or to their replacement. Amongst other things, such responsibility shall extend to damaged walls, tiles,

fixtures and fittings whether or not the unit has been built into a cupboard and irrespective of the stage either of
its installation or the fitting of any other item whatsoever in its vicinity.

No other person, or firm or corporation is authorised by Condari to offer or give on its behalf any other greater
warranty than that given by Condari under this warranty.

Condari Pty Ltd provides to all QASAIR Rangehoods a 10 year motor replacement warranty. This is a change
over warranty.

The installation of the rangehood must comply with the information in this guide. Failure to follow the instructions
may result in loss of the warranty.

We do point out that incorrect installation such as the ducting being the incorrect size or the duct run being too

long will result in the motor failing and possible burning out.

The change over will be carried out by a authorized technician and will be charged at the rates applicable at
time of the change over.

Qasair Rangehoods Installation Instructions48

EXCLUSIONS

There are some exclusions from the Condari Pty Ltd Guarantee. (on previous page)

CONDOR Rangehoods are designed to be used over all domestic barbecues available
in AUSTRALIA.

QASAIR Rangehoods are not to be used over barbecues approved for outdoor use only.

Outdoor barbecues will have a rating plate on them specifying that they are approved for outdoor use only and
also a mega joule rating per burner or a total mega joule rating.

In practice any barbecue or outdoor cooking appliance over 50 mega joule will need a specially made
rangehood with an air movement exceeding 2000 cubic meters per hour.

QASAIR have hoods to go over domestic cookers such as VIKING, WOLF and CAPITAL cooking appliances.
These brands have a mega joule rating of up to 95 mj and therefore special hoods are required for the

appliances.

CONDARI will manufacture special rangehoods to go over commercial cooking appliances situated in domestic

kitchens.

Once the heat output is over 50 mega joule a special rangehood is required.

Qasair Rangehoods Installation Instructions

49

STANDARD
WARRANTY

Date purchased

Purchased from

Model

Serial No

The purchaser must fill in the above information and keep this with the original purchase document.

This form must be produced if and when
a claim is made under this warranty.

QASAIR Rangehoods are made in Ringwood, Australia.

Tel: [phone]
Fax: [phone]
Email: [e-mail]

Pleae Note that the Warranty is from the date of installation and the service technician will need to see proof of
purchase so he can provide service under the guarantee.

If no proof of purchase then the service call will be charged at standard rates and if proof provided later,

reimbursement will be made.

Qasair Rangehoods Installation Instructions50

EXTENDED
WARRANTY

Condari Pty Ltd provides an extended warranty from 36 months to 72 months if installed by an authorised

Qasair installer and the below form is completed.

The authorised installer also offers a warranty on their workmanship for the same period of 72 months with a

guarantee that the installation is in compliance with
‘Qasair installation instructions’.

Customer Name:

Model Number: Serial Number:

Purchased from:

Purchased Date: Installed Date:

Installer Name:

Installer Signature:

Condari Pty Ltd authorised installer stamp:

(This is required for validity of extended warranty)

Pleae note: The installation warranty does not cover the ageing process in a building or any problems due to

storm damage.

Qasair Rangehoods Installation Instructions

51

NOTES

Qasair Rangehoods Installation Instructions52

NOTES

Qasair Rangehoods Installation Instructions

53

NOTES

Qasair Rangehoods Installation Instructions54

NOTES

Qasair Rangehoods Installation Instructions

55

www.condari.com.au

DISTRIBUTED IN AUSTRALIA BY CONDARI PTY LTD

Tel: [phone]
HEAD OFFICE
VIC Tel: [phone] Fax: [phone]
Email: [e-mail]
Website: www.condari.com.au

YOUR DISTRIBUTORS

NSW/ACT Tel: [phone] Fax: [phone] Email: [e-mail]

QLD Tel: [phone] Fax: [phone] Email: [e-mail]

WA Tel: [phone] Fax: [phone] Email: [e-mail]

SA/NT Tel: [phone] Fax: [phone] Email: [e-mail]

TAS Tel: [phone] Fax: [phone] Email: [e-mail]

New Zealand

Kouzina Appliances Email: [e-mail]

Singapore

Eldric Marketing Pte Ltd Email: [e-mail]

CONDARI RESERVES THE RIGHT TO CHANGE SPECIFICATION WITHOUT NOTICE

QASAIR RANGEHOODS MADE IN RINGWOOD 3134

rev. 150318