Pyle PQE 2100 User Manual
Professional Power Amplifier
PQA 2100
PQA 3100
PQA 4100
PQA 5100
B
B
B
B
www.pyleaudio.com
De
PQA
s
De
De
d
d
e
e
n
n
g
g
si
si
gi
gi
n
n
e
e
d
d
n
n
a
a
d
an
an
ed
ed
n
n
g
g
i
i
s
i
i
d
d
e
e
r
r
e
e
e
e
n
n
r
ee
ee
n
n
i
i
g
g
en
en
d
A
A
S.
S.
U.
U.
n
n
PQA
De
A
A
S.
S.
.
.
U
U
n
n
i
i
d
d
e
e
r
THD
Model
2 OH M S
PQA2100
1050+1050w rms
460+460w
230+230w
920+920w
>85dB
>70dB
>250
30v/μs
Short circui t,C urrent lim iter, T ermal cut off ,Slo w Star t,
Limiter,AC li ne fus e, DC fault,Power u p/do wn tra nsients
<140W
PQA3100
1550+1550w rms
760+760w
380+380w
1520+1520w
10Hz-50KHz -1.5dB
21dB/9V
20K OHMS
>85dB
>70dB >70dB
>250
h
30v/μs
Variab le Speed Fan
<300W
AC 115V- 230V/ 50- 60H z
PQA4100
2050+2050w rms
1000+1000w
500+500w
2000+2000w
>90dB
>250
30v/μs
<300W
PQA5100
2550+2550w rms
1200+1200w
600+600w
2400+2400w
>90dB
>70dB
>250
30v/μs
<300W
OVERVIEW
It is well- known the PQA series professional amplifier is designed by the
specialist who has full experience and new model equipment. To raise
reliability of the amplifier, PQA series professional amplifier has been
installed with short distance cooling unit,
high- speeding and consistency to increase the life of the power parts.They
all have adopted mature and reliable circuit with SMT technology.
The conventional amplifier applies tunnel- model cooling system, this kind
of system has long distance for heat dissipation, the hot air is distributed
with difficulty, and theradiator is very hot at the top, but too cool at the
bottom, the temperature difference goes between 2 0℃-4 0℃,those system
produces temperature difference easily in the power parts, the electric
current is high in hot parts, which results in its damage and reduces the
using- life and reliability.
PQA series amplifiers has full-protection, including:
Soft start function to prevent wave shock at power- on.
Delay function for prevent shock at switch power on.
DC protection.
Over- electric current protection.
Cut- wave protection.
Over heat protection.
482x 314 x88 mm
8kg
9.5k g
10.5 kg
11.5k g
Installation guidelines
DO NOT use these amplifiers in damp or high humidity environments.
。
Do not use outdoors or anywhere where liquids could fall or splash onto the amplifier.
Ensure the amp is adequately ventilated, with free airflow to the front and rear panels.
。
Keep away from other heat sources. If the amps are mounted in a rack with other amps,
ensure there is adequate cool air flow front and rear. Note that air is drawn in through
the back panel, and exhausted through the front panel.
NEVER cover the amplifiers, as they may overheat.
。
PQA power amplifiers are designed to fit standard 19 racks, with a 2U height
。
and 17 depth. We recommend the use of rear rack supports, especially if the rack is to
be mobile. Use shake proof washers or thread lock adhesive to prevent mounting bolts
becoming loose in transit.
Ensure that the AC power supply is correct for your amplifier. The required AC supply
。
is stated on the rear panel next to the AC power input.
ATTENTION
Never put any parts on the top of the amplifier.
Using fixed power socket that must be has enough capacity to prove power.
Never switch the power on and off continuously at the same time.
Donruction in the air vent of front panel.
Input stereo level can be adjust by own gain mixer, in bridge- model connection,
the adjustment will adjust by CHA channel mixer.
The output connector have 3 kind model, tie- model, phone model and professional
speakon connector for connecting.
When using stereo, bridge, mono function, the connect model must be same than
model switch selected.
When output high- power signal continuously, the amplifier should be has speedup in the cooling fan, it may be have low noise produce in this equipment, it is
normally.
The general gain of the amplifier can be adjust by gain knob, the input level
have 0 .7 7V, 1 .4 V, full- power out and fixed 2 6dB gain 3 band should be selected.
Donr vent of rear panel.
When clear-up the cover of the equipment, you must be power off and loose the
power Plug using dry- cloth to clear, never using and solvent that have corrosive
to clear.
If have problem happened, power down immediately, and contact with dealer.
Ensure that you use the correct type of mains lead for your equipment and country.
。
This must be free from damage and easily accessible during use.
www.pyleaudio.com
www.pyleaudio.com
Loading...